Search Documents

The segregation process has been known for many years and applied industrially for the treatment of various refractory copper ores. The principles of the process are briefly reviewed; the process was tested in the laboratory on two copper-cobalt oxide ores from Gecamines, Shaba Province, Zaire. Various parameters of the process, such as segregation temperature, dosage of reducing and chloridizing agents and flotation conditions were inyestigated. Experimental results have shown that the segregation of copper could proceed satisfactorily at low temperature (1000° K) but that of cobalt required higher temperature and higher additions of reducing and chloridizing agents.

Jan 1, 1992

By Brij M. Moudgil

Flotation of fine and coarse coal after multistage addition of the frother was found to yield coal fractions with significantly lower ash content as compared to the feed. It was observed that the lowest ash content, specific gravity and reactivity of coal was associated with finer size fractions. Ignition and combustion characteristics of different coal fractions were evaluated using a differential thermal analyzer (DTA) with calorimeter attachment. It is suggested that in the ignition stage, the removal of mineral matter affects the reactivity through the physical changes brought about by the ash removal. In the char combustion stage the mineral matter seems to influence the reactivity through the catalytic activity of surface concentrations of metal ions, ratio of combustible/incombustible material, internal pore structure and roughness.

Jan 1, 1984

By Alexander I. Feldman, Michael S. Kucker, Robert A. Robinson, Harvey W. Parker

An extensive geotechnical monitoring program was used to assess ground and liner behavior, provide input to a Disputes Review Board, and verify design assumptions during construction of the Mt. Baker Ridge Highway Tunnel along I-90 in Seattle, Washington. The stacked-drift tunnel liner was constructed with twenty-four 2.9 m diameter concrete-filled drifts forming a semi-flexible compression ring, followed by excavation of the 19.4 m diameter soil core. Instrumentation data was used for monitoring hillside stability, liner deflections and loads, impacts on adjacent highway tunnels, for back analyzing soil properties, and for helping to limit construction-induced settlements to about 6 cm.

Jan 1, 1987

By Ruiren Jin

In alkaline pulp, galena is depressed by sodium carboxymethyl cellulose (NaCMC), while Cu(II)-activated sphalerite exhibits a high flotability so that satisfied separation can be achieved. In addition to hydrogen bonding, chemical bonding of NaCMC with galena is confirmed by IR; only hydrogen bonding is involved between NaCMC and Cu(II)-activated sphalerite. It is also found that the greater the degree of substitute and polymerization of NaCMC, the stronger the depressive effect of NaCMC and that lower stirring speed favors the depression.

Jan 1, 1987

By Lok W. Home

HISTORICAL DEVELOPMENT At the beginning of the 1970 more than 90% of pro¬duction drilling in open-pit mining was obtained with the use of rotary drills. At the same time, the use of rotary drills underground was virtually nonexistent. Several progressive mines began questioning whether efficient rotary drilling could not be adapted to under¬ground applications. In the late 60s and early 70s at¬tempts to use rotary drilling were made by Inco, Ltd. and Meramac Mining, utilizing drill units designed as a combination of small diameter raise drills and rotary drills. These initial attempts were unsuccessful primarily due to the immobility of the equipment and low degree of dependability. At the same time, experiments con¬ducted by Inco and Meramac using large diameter in¬the-hole percussion drills produced immediate encourag¬ing results. The first serious attempt at utilizing rotary drilling underground was made by Texasgulf in 1971 at Kidd Creek mine in Canada. An experimental stope 15 m wide, 36 m long, and 30 m deep was drilled using 200-mm diam rotary drilled holes. The machine used was a Robbins' Model 11 D. The Model 11D is a rotary drill designed to drill drain and utility holes under¬ground. The results of this test revealed that large diameter blasthole stoping was feasible. The indications were that the major areas of concern-fragmentation and pillar damage-could be controlled and a new low-cost stoping method resulted. At this point Texasgulf and Robbins entered into a cost-sharing agreement to develop a rotary drilling unit specifically for this stoping method. Drilling of the trial stope required pouring a concrete pad at each drill hole plus anchoring the derrick to the pad by means of rock¬bolts. Utilization expressed in terms of drilling time to available time was less than 20%. It was obvious that the required unit had to be mobile, setup time had to be minimized, and rod handling had to be improved. The first attempt at an underground production-type rotary drill consisted of mounting the basic 11D on an air-powered Eimco 600 Series crawler. The crawler was equipped with four screw-type leveling jacks operated by an impact wrench; rod rack facilities for 60 m of 1.2-m long, 170-mm diam rods; a rod handling facility consisting of an air-lift swing boom and a pipe loader which automatically positioned the rod under the float¬ing drive box; a turnbuckle anchor system requiring in¬stallation of four rockbolts in the drill drift floor and placing turnbuckles from the rockbolts to the corners of the drill; and trailing power units containing the electrics and hydraulics required to operate the drilling unit. Operation of this unit revealed a vast improvement in drilling time but some problem areas remained. The anchoring system required secondary drilling and proved difficult to adapt to the localized irregular floor surface and the trailing power unit was difficult to maneuver and was causing unnecessary maintenance costs. Addi¬tional improvements resulted in the standard 11MD rotary blasthole drill. DESCRIPTION OF UNIT This standard model consists of the drill and the power unit integrally mounted on an air-powered crawler chassis (Fig. 1). The rod-handling and leveling¬jack systems are similar to those used on the prototype Texasgulf unit and remained relatively the same. The anchoring system has been replaced by the roof jack, initially screw type but now hydraulically actuated. The anchoring system is necessary as the drill exerts more thrust than the weight of the unit. During operation it is found that the two front jacks adequately anchor the machine. The complete unit's operational dimensions are: height, 3.2 m; width, 2.1 m; and length, 4.2 m requiring a 3.5- x 3-m drill drift. The derrick is pivot mounted and raised and lowered by a hydraulic cylinder reducing the transport height to 2.5 m. The derrick is also turnbuckle mounted to allow dip angle drilling from vertical to 0.52 rad (30°) off vertical. The drill derrick can be mounted to allow dip axis to be parallel or perpendicu¬lar to the long axis of the unit. The standard rods are 1.2 m in length and are contained in racks of 10 which can be removed for transportation. Drilling torque is produced by a 56-kW (75-hp) electric motor driving a double vane pump which in turn drives a Robbins high torque gear-type hydraulic mo¬tor. In addition to the hydraulic motor, the machine drive system has a 3.9:1 planetary gear reducer. This results in six speeds with the following minimum and maximum range: Maximum rpm 112 Torque 3725.5 J (380 kg m) Minimum rpm 10 Torque 14 706.0 J (1500 kg m) Drilling thrust is provided by two bootstrap cylin¬ders pressurized by a variable volume pump. This sys¬tem can produce from 0 to 267 231.2 N thrust in either direction. Bailing air (approximately 17 m3/min at 382.2 to 490.3 kPa) is introduced through a rotary swivel pass¬ing directly through the center of the drive system to keep efficiency and losses to a minimum. Hole annulus is also kept to a minimum by using 170-mm rod when drilling a 200-mm hole. A small amount of water is added to the air for dust suppression. The machine has to be supplied with air, water, and electrical power. It does not appear feasible to provide an integral air power supply with the rotary drill such as is done with open-pit rotary drills. Air is required and installed during the primary development of the drill drift. The machine can be adapted to drill hole diameters from 170 to 228 mm for blasthole operations. The drill string consists of the rotary bit, crossover stabilizer, roller stabilizers, and standard rods. The operator controls speed and thrust pressure from an operating console which can be mounted in a conve¬nient position. Mount Isa has made an adaption to the operating console to permit remote collaring of drill holes in an uncleared floor.

Jan 1, 1982

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009

By D. M. S. Bhatia

Twenty-six insitu analyses of cubic galena crystals from a Mississippi Valley-type deposit were undertaken with a laser microprobe spectrograph to study the variation of nine trace elements from the crystal center to its periphery, both along the diagonal and vertical. The general trend is an increase in the concentrations of Ag, Ga, Ge, and In with As showing the opposite trend Bi, Cd and Sn did not show any pattern. Sb was not detected. These variation patterns nay serve as a model for similar studies of other Mississippi Valley-type deposits.

Jan 1, 1984

By J. Chai, Q. Yuan, B. Qiu

"Overburden strata deformation monitoring is one of the key problems in ground control. Using geophysical method through surface drilling to detect strata deformation is commonly used in the industry. In this paper, a geophysical method based on the distributed optical fiber sensing (DOFS) system were conducted in the laboratory, where a DOFS-based strata deformation monitoring experiment was performed with three physical models. The results show that the DOFS method precisely detects the rock mass deformation and strata structure forming with the Brillouin frequency shifts (BFS) representation. The BFS curves are divided into three phases, which reflects the horizontal three zones developed in the overburden. The BFS distribution presents a multiple stages form, the 1st stage corresponds to the caving zone and the 2nd stage corresponds to the fracture zone. Based on the multiple stages form, the evolution of the water flowing through fractured zone have been determined and the controlling effect of key strata over the water flowing fracture has been pointed out. In the end, the comparison validation proves the accuracy and reliability of this method, and it could be a new approach for the ground control research. INTRODUCTION Overburden rock strata above the work face space will propagate from slight deformation, part destruction to violent movement because of the underground coal mining. It is fundamental and an intrinsic requirement of ground control to monitor the mining-induced rock mass deformation.[1] Overburden strata have their significant mechanical behaviors and movement under damage deformation and fracture. Overburden strata deformation affect the mining ground pressure control directly, and performance in the relationship of supporting equipment and the surrounding rock, the mining-induced fracture distribution and the loss of underground water resource, the ground surface structure stability and the ecological environment.[2] From the perspective of the concept of safe and efficient scientific coal mining: the overburden strata deformation is an important part of mining method selection and reasonable supporting solutions decision which can solve the issues like the roof supporting force calculation, overburden fracture distribution and gas drainage, ground subsidence, separation of coal and rock control and top-coal recovery rate and so on. From the perspective of green and ecological mining: the overburden strata deformation is the key basis of studying the mining-induced ground subsidence and mining area ecological damage, and such engineering problem like environmental protection in mining area, ecological restoration in mining subsided land and the water conservation in fragile ecology area of mining could be solved based on it.[3-6] Therefore, the mining-induced overburden strata deformation is the key of ground control and needs to be controlled artificially."

Jan 1, 2017

By Anthony Busigin, Stephen Pogorski, Colin R. Phillips

The precision of radon daughter measurement techniques is a complicated function of uncertainties arising from concentration and flowrate fluctuations during sampling, counting statistics and many other factors. Optimization of a measurement technique requires that all these uncertainties - not just counting statistics - be considered. In this work, the optimization procedure of Busigin and Phillips (1980) is tested against Monte Carlo experiments for the case of the modified Tsivoglou method.

Jan 1, 1981

By Erwin A. Morlan

Present methods of boring large hole mine openings are briefly reviewed. Factors that influence the design and choice of down-the-hole equipment for rotary drilling large holes are discussed. With formation drillability taken as a starting point, graphs and charts are given as an aid in the selection of bit load, circulation system, flow rate, drill stem, cutter design and rotary speed.

Jan 1, 1961

By John W. Conn, Harry C. Verakis

An explosion in an underground coal mine can have a devastating effect on the main fans used to provide mechanical ventilation. The Code of Federal Regulations, Title 30, Part 75.310 (CFR, 1992), specifies that each main mine fan shall be offset by at least 15 feet (4.6 m) from the nearest side of the mine opening unless an alternative method of protecting the fan is approved in the ventilation plan. Also, each main mine fan shall be protected by one or more weak walls or explosion doors. This paper presents venting and fan configuration designs which provide a comparable degree of safety for explosion protection. Design flexibility is enhanced and a means for consistency in safety judgements is afforded.

Jan 1, 1993

By G. F. Revey

All underground operations have limiting factors that influence overall profitability. Hoisting, hauling, available headings, labor, milling capacity and other factors limit how much material can be removed from an underground mine. Consequently, when mines use limited labor to handle the additional rock from overbreak and to perform extra ground support tasks, productive activity is replaced by nonproductive work. Mining economics are further penalized when overbreak causes dilution of ore grades. This paper reviews the organizational systems that mines have been using to create environments that foster the creation of successful overbreak-control programs. Actual case histories document the various quality-improvement techniques, worker incentives and practical project-management systems used by these mines. A brief review of controlled-blasting technology sources and overbreak-measurement tools is also included.

Jan 1, 1999

By Paul H. Johnson

A new system for leaching many types of ores has recently been developed on a commercial basis by J and J Research and Development, Inc. of Hanover, New Mexico. This revolutionary new leaching system consists principally of three new leaching reactors; viz, (1) a large, air-agitates, column-like reactor for leaching crushed ores that is constructed in an underground environment and has the inherent ability to do a very efficient job of leaching, (2) a vat-like, air-agitated vessel for leaching an rinsing finely ground ores and , (3) an air-agitated copper precipitation column that is built underground and utilizes an inexpensive dense or heavy scrap iron as a copper precipitant. Each of these new reactors have been used in a large leaching plant near Hanover, New Mexico.

Jan 1, 1973

By B. S. Treiber, R. A. Lohnes, S. M. Levorson

As part of a research program to develop a coal-handleability index that would predict the ease with which a coal would flow through a handling system, an apparatus was developed to directly measure the unconfined Yield strength and bulk density of consolidated-coal samples. The new test apparatus provides a fast and simple method for determining the strength and compressibility parameters that are associated with the handling characteristics of crushed coal. Comparative tests were conducted using a low-stress triaxial-test apparatus. To check the accuracy of the new method, four coals with a variety of moisture contents and gradations were tested using the new method. These tests indicate that the new test device yields valid results. Further, the speed and ease of operation of the new device makes it suitable for quality control and quality assurance in plants.

Jan 1, 1996

By Dominique Francois-Bongarcon

The world mining industry is facing a severe recession. Thus, it is time to recall the value of geostatistical methods which were formerly developed as a money-saving and productivity-increasing tool. The situation has worsened, but the techniques of geostatistics have dramatically changed. Up to millions of dollars can be saved during exploration with simple use of variograms; then, during reserves estimation with kriging methods; and finally, with the parameterization of reserves, when evaluating a project and optimizing its global mining parameters.

Jan 1, 1983

By Por J. B. Evans

El mantener un beneficio óptimo sobre todo el conjunto de un emplazamiento minero necesita una constante puesta al día de las estrategias operativas. En esencia, cada estrategia es una combinación particular del gasto del capital previsto, el flujo de ingresos y el tiempo transcurrido. La selección de una estrategia basada en el beneficio potencial requiere que cada estrategia contemplada con un ordenador, un análisis tal puede ser engorroso. Este capítulo discute o desarrolla una técnica de "corte rápido" que asigna una relación de beneficio a las estrategias alternativas e identifica aquellos aspectos de una estrategia que producen mayor impacto sobre el beneficio. Esta técnica puede proporcionar valoraciones rápidas de suficiente precision para muchas de las decisiones de las estrategias operativas que se toman sobre la marcha en minas que se encuentran en explotación.

Jan 1, 1982

By Jorge Gutierrez C.

CODELCO-CHILE, the world's largest copper producer, began an integrated study of the informatics situation in the corporation at the end of 1980. As a result, a five years strategic Systems Plan was elaborated and approved by top Corporate management. Main points in this plan were: a systems architecture with information integration to the top level management; a higher degree of information technology in the production areas, an optional systems development resources utilization and a high profitability of the plan itself. During the study phase a series of theoretical definitions were fixed and used as a basis for the plan's design. A "common systems" approach was chosen as the development strategy instead of corporate systems or separate divisional efforts. Top management should be highly involved in the revisions of the plan, as well as qualified users should be chosen as project managers. The systems architecture should grant the information integration to the corporate level, in order to support an integrated planning and administration environment for the corporation. A total of 15 projects were defined, involving 570,000 man-hours and shifting the development efforts towards the production and production services areas. The paper presents a critical evaluation of the whole process, showing its good and bad aspects and a positive global balance. It also points some suggestions and hints to any corporation who wishes to get involved in a similar experience.

Jan 1, 1989

By P. K. Crane, S. C. Gambrell

The work reported herein compares the support characteristics of two different types of roof truss subjected to the same force in the horizontal tension member. The major differences between the two trusses are in the sequence of tensioning the horizontal and inclined members and in the design of the loading brackets. A photoelastic model was used to compare stresses at points along the roof of the mine opening and at the junction of the roof surface and the rib. The effects of simulated subsidence on stress in the roof and on tension in the horizontal member were analyzed. Results indicate that there are significant differences in the overall support characteristics of the two trusses. Conclusions are drawn relative to which type of roof truss provides the most favorable support if the horizontal members are tensioned equally.

Jan 1, 1986

By N. Edmonson

The demand for sulfur divides into two major categories: agricultural and industrial. Most of the agricultural demand is related to the production of phosphate fertilizer products. Industrial demand is derived from the demands for a large number of products and is related to a variety of industrial processes, no one of which characterizes it in a simple way.

Jan 1, 1994

By Maurice L. Madden

An investigation was undertaken for a ground water discharge plan for the Chino mining complex near Hurley, New Mexico. Operations which impact ground water include dump leaching, storage reservoirs, and tailings seepage. The investigation included both hydrogeological data collection and laboratory analysis. A conceptual understanding of surface water and ground water was then developed. Surface water and ground water models were used to match existing conditions and predict the impact of operational modifications. The study concluded that runoff and resulting leach reservoir overflows were primarily responsible for the ground water degradation. Tailings seepage represents a smaller part of the impact.

Jan 1, 1984