Search Documents

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By Colin Rawlings, Simon Pepper, Maria Karakitsiou, John Mathews, Peter Townsend, Russell Bowler, David Keeble, Christopher Darton, Scott Sadler

National Grid needs to maintain a connection between two existing electricity sub-stations (Beddington & Rowdown) in the Croydon (south London) area, and allow the replacement of two 275 kV cable circuits that are buried under roads. This is to be achieved using a single 400 kV cable circuit within a 10 km (6.25 mile) long, 3 m (9.8 ft) diameter high voltage cable tunnel which is being driven through water bearing Chalk, at depths ranging from 5 m (15 ft) to 80 m (262 ft), with four access shafts(12.5 m (41 ft) in diameter) ranging in depth from 10 m (31 ft) to 40 m (131 ft). The Chalk in this area acts as a source of public drinking water supply (PWS) and is protected by areas designated Groundwater Source Protection Zones. To minimise the groundwater risk the design and construction of the cable tunnel and shafts has paid particular attention to the construction materials used, including testing of these construction materials prior to use, developing construction methods (including the design of the Earth Pressure Balance TBM) and maintaining a groundwater monitoring & testing programme prior to and during construction to ensure the integrity of the Chalk aquifer is maintained as a drinking water source. This paper describes the tunnel &shaft design and construction in relation to these particular groundwater environmental issues which set new precedents for tunnel assessment, design and construction requirements in the United Kingdom.

Jan 1, 2007

By C. -G. Zhang

This paper presents the results of a study on cellular acclimation of Acidithiobacillus ferrooxidans to sulfur biooxidation in terms of cells growth and changes in surface properties and morphologies of both cells and sulfur particles. The results showed that A. ferrooxidans cells were grown faster and demonstrated higher concentration in the soluble thiosulfate substrate than in nonsoluble hydrophobic S0 substrate. The results showed that A. ferrooxidans cells acclimated to the sulfur biooxidation by actively expressing some extracellular polymers substance and maybe some outer membrane proteins that modified the surface properties of both sulfur particles and the cells themselves. In addition, the results showed that the A. ferrooxidans cells were able to dynamically adsorb to or desorb from the surface of sulfur particles. The cells aggregating onto the S0 surface enhanced the use of S0 substrate by the bacteria cells. This mode may be one of the most important characteristics for the better growth and propagation of the cells in solid sulfur-containing media.

Jan 1, 2009

By J. Kretschmann

Around the world, mining has been done for thousands of years for the benefit of humankind. The winning process in mining operations ends with the depletion of the deposit or its closure if the operation becomes economically unprofitable. After that, a period of post-mining follows which may last for a very long time and which is generally regarded as a period of hazards, risk and high cost. In the USA alone, approximately 500,000 abandoned mines do exist; worldwide, there are millions. In Germany, too, we have had to deal with abandoned mines for a considerable period of time now.

Jan 1, 2012

By S. Christiansen, G. R. Winslow, R. W. Kobler

Todays End of Life vehicles are shredded and their metal components recovered and recycled by standard methods. The remaining non-metallic fraction is shredder residue, and contains vast amounts of high value engineering plastics. None are today recovered. Discussed are the developmental approaches used in the first process to recover these valuable plastics. Examined are initial laboratory studies, pilot plant design and construction, product development, results, and flowchart explanations.

Jan 1, 2001

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By William Crowe Kellogg

By now the term AFMAG has been fairly well introduced to the mining industry. Several papers have been presented and published concerning AFMAG (references 1 and 2). However, the term AFMAG remains rather new to the industry, and the exact place which AFMAG occupies in the minerals exploration field is still somewhat uncertain in the minds of many who may have use for this new and interesting method of electromagnetic exploration for conductive minerals. It is the purpose of this paper to again review the basic theory of the AFMAG system, to describe and - illustrate the equipment and data presentation as used in aerial surveying, and to provide some idea of the cost and nature of airborne AFMAG surveys. This paper is primarily of a general descriptive nature and presents AFMAG theory in a schematic rather than mathematical form; emphasis is placed on the equipment, the present method of data presentation and survey operations, since it is believed that such, information will now generally best serve to inform the mining industry of the characteristics of the AFMAG system.

Jan 1, 1960

By Thomas D. Kelly

In 1900, the average U.S. citizen’s average life span was 47 years. He traveled about 1,900 km (1,200miles) in a lifetime and resided in a home with an ice-box for food storage and oil or gas for lighting. He communicated by mail, telegraph and crude telephones with limited availability and range. By 2000, the average citizen’s life span was 77 years. He traveled an average of 19,000 km/a (12,000 miles/year) by automobile alone. He resided in a home with many electrical appliances, including refrigerators and electric lights. And he communicated almost instantaneously with any other part of the globe by several widely available means, including portable phones and e-mail.

Jan 1, 2002

The use of coal as a fuel causes air, pollution in; a number of different forms, and in nearly all stages of its, handling, preparation, storage, use and-disposal of its residue. First let us consider the handling of coal. As shipped, particularly to large utilities, it is run-of-mine bituminous made up of large chunks as well as pulverized particles. Because it 'is in an open car or barge, it is subject to the action o winds and the small particles may be blown around adding to the-particulate load in the atmosphere. Mien un¬loaded from the barge or car, there is again an opportunity for the wind to blow the fine particles around. All of us I am sure have seen a barge at the dock of a utility plant being unloaded by a clamshell bucket. This, after grabbing its load from the barge, lifts it some 60 or 70 feet and, then drops it on a conveyor, which carries the coal to a storage area.

Jan 1, 1964

By Dan Martz, Bill Moler, David Young, Wally Chen, Matthew Crow, Steve Norris, Tolga Togan

Two 610 m (2000 ft) long tunnels were driven through water bearing silts, sands and clays beneath the Sacramento River using a 4.59 m (15.1 ft) diameter Earth Pressure Balance Tunnel Boring Machine (EPBM). Four sheet pile shored shafts were sunk with and without dewatering. The pre-cast concrete segmentally lined and grouted tunnels were driven down at 6% grades beneath the river flood protection levees, buildings, roads, a railroad and adjacent to a Freeway Viaduct. Details of the schedule, cost, shaft construction, TBM, tunnel construction, and installation methodology for the twin1.676 m (66 in) steel force main pipes and environmental constraints are provided.

Jan 1, 2007

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007

By K. Lang

A case study is provided that highlights the successful use of high efficiency electrical submersible pumps (ESPs) adapted from the oil and gas industry for a large scale, open pit mine dewatering operation. In this case, the mine is Goldcorp?s Peñasquito Mine, Peñasco and Chile Colorado open pit development areas in Zacatecas, Mexico. At the time of publication (July 2012), there were 18 vertical bedrock dewatering wells producing an average flow rate of 350 liters per second (lps) from the Peñasco and Chile Colorado development areas. Average pumping rate per well was 18 lps, with a maximum of 44 lps. The depth of wells varies from 330 m to 500m, and includes both in-pit and perimeter (ex-pit) pumping centers. A network of 50 piezometers was used to monitor the response of groundwater levels to pumping. Since dewatering operations were initiated in 2007, groundwater elevations decreased overall, from approximately 1950 m above sea level (masl) to around 1625 masl, for a total of 340 m of drawdown. The pit floor elevation was approximately 1655 masl. All of the producing wells were constructed with 16-inch boreholes, completed with 10-inch diameter blank casing and louvered screen sections and equipped with ESPs. The application of ESPs has proven to be highly effective in the case of Peñasquito?s dewatering operations. Noted advantages include the following: ? Small diameter pump allows use of smaller diameter boreholes (16 inches) and casing / screens (10 inches) reducing well drilling and construction costs ? Greater application range for flow rate and total dynamic head ? Variable speed drive systems for greater energy efficiency and flow rate optimization ? Integration of downhole instrumentation into the motor and pump assembly The advantages and benefits of using high efficiency ESPs revolutionized the dewatering program at Peñasquito open pit mine as evidenced by the number of deep vertical well installations and high dewatering flow rates and total dynamic head requirements.

Feb 27, 2013

By John Zeni

In Australia during the 1990s, Zeni Drilling took on several demanding shaft boring contracts. This paper describes the safety, operational, technical and environmental advantages derived through the implementation of mechanized boring methods for two of these projects. The paper first describes a 3-meter (10 ft) diameter access shaft blind bored from an underground location to 440 meters (1,444 ft) deep for a gold mine in Tasmania. The construction of a 5.8-meter (19 ft) diameter, 515-meter (1,690 ft)deep ventilation shaft for a longwall coal mine in New South Wales is also described.

Jan 1, 2001

By G. S. Austin

The St. Cloud Mining Company extracts clinoptilolite about 6.5 km south of Winston, Sierra County, New Mexico. Production is about 18,000 mt/year. Natural zeolites are good adsorbents for positively charged solutes such as ammonium. St. Cloud’s production is used in animal hygiene, animal feed, environmental mitigation, air and water filtration, and other applications. By a simple chemical treatment with a surfactant, zeolites can also be modified to adsorb negatively charged solutes such as nitrate and arsentate, and neutral organics such as solvents and fuel components. These surfactant-modified zeolites are used in treating groundwater contamination, stormwater runoff, and solvent vapors from painting operations.

Jan 1, 2002

By Silvano Morelli, Giovanna Cassani, Renzo Bindi, Antonio Nicola

More than 70 km of main line and service tunnels have been excavated to date for crossing the Apennines between Bologna and Florence. A new design and construction approach, known as Analysis of the Controlled Deformation in Rock and Soils, (ADECO-RS), was adopted to tackle the extreme heterogeneity of the ground and the particular stress-strain conditions. The goal of this system is to obtain constant and predictable full section advance rates, even in very poor geology, with the highest possible level of safety and reliability. The execution of this gigantic project required the mobilization of 21 job-sites, with the concurrent operation of 30 excavation headings. The global production rates confirm the high quality of the design and the high level of industrialization reached during the construction stage, levels not previously obtained in similar conditions, using other approaches such as NATM.

Jan 1, 2003

By Steve Kral

The mining industry has had three difficult years. Commodity prices have remained low and investor confidence in the industry has been shaken. And even though the Asian economy appears to be improving, it will be some time before this improvement will translate into better commodity price conditions for mining. In addition, increased environmental and social restrictions that have been placed on the industry in developed and developing countries have made mining a more difficult proposition. And, if that is not enough, the global mining industry has found itself in fierce competition with Internet businesses for investor capital. Despite that gloomy picture, more than 10,500 mining industry professionals from about 70 countries gathered in Toronto, Ontario March 5-10, 2000 for the Mining Millennium 2000 conference. This meeting was a joint effort between the Canadian Institute of Mining, Metallurgy and Petroleum(CIM) and the Prospectors and Developers Association of Canada (PDAC).The joint meeting also featured two trade exhibitions and more than 150speakers. PDAC’s trade show attracted about 400 exhibitors and an additional 200 in the concurrent Investors’ Exchange. CIM’s exhibition attracted about 600 equipment and service companies.

Jan 1, 2000

By Steven Hoerger

Newmont Mining has a large, integrated gold-mining operation in northern Nevada with several mines, stockpiles and processing facilities. There are more than 90 defined metallurgical ore types and more than 60 defined gold-recovery process options. Newmont developed a mine plan and process model to take better advantage of the available synergies at its Nevada mines. This plan includes a mixed integer and linear programming optimization tool. This system is maintained and operated by a Nevada planning group. Standard in-house planning software tools and methods have been implemented at all mine sites. These changes have allowed a reduction in mine engineering staff and have increased the effectiveness of mine planning.

Jan 1, 1999

By Laurens de Jonge, Wiebe Boomsma, Rodney Norman, Stanislav Verichev

"Earth provides natural resources, such as fossil fuels and minerals that are vital for human life. As the global demand grows, especially for strategic minerals, commodity prices rapidly rise. Thus there is an identifiable risk of increasing supply shortage for minerals. Hence a major element in a long-term economic strategy must be, to ensure security of supply for these strategic minerals. In this rapidly changing global economic landscape, deep sea mining has gone from a distant possibility to a likely reality within just a decade.Although deep sea minerals extraction was investigated in the 1970’s, it was abandoned because of changing commodity economics, advances in on-land exploration techniques, growing concern on environmental impact, and political and legal aspects with regard to ownership issues. The developmental data from those days, if still available, are not adequate to allow engineering and building of an integral system for extraction of deep sea minerals without additional R&D work. Thus, deep sea mining is yet to attain a Technology Readiness Level (TRL) sufficient to successfully undertake deep sea mining operations, from resource discovery to resource assessment and to resource exploitation [Blue Mining, 2014]."

Sep 1, 2014

By Hassell E. Hunter

The Wyoming Mineral-Conoco Crownpoint Project represents the first time that big hole drilling has been exclusively used to develop totally a privately financed mine below a depth of 1000 feet. Three shafts, one ten feet in diameter and two six feet in diameter, were successfully drilled to depths of 2243', 2188' and 2188' respectively and cased with hydrostatic designed steel casing. The largest shaft is to be used to handle muck and water from station excavation and enlargement of the other two shafts. A reverse circulation system with potassium chloride base mud was used for drilling. The mud was cleaned by settling in steel lined tanks with assistance by cyclone type separators. Deviation was monitored by gyroscopic surveying at 30 foot intervals and did not exceed 16 inches off plumb. Casing was designed to withstand hydrostatic pressures with a 1.5 safety factor to the large shaft and 1.25 safety factor for the smaller shafts. All casing welds were x-ray tested prior to lowering the casing in the hole. Cementing the annular space completed the operation. The total time to mobilize, drill and move off the three shafts was 363 days. The drilling operation was completed ahead of schedule and under budget.

Jan 1, 1983

De Beers? Finsch diamond mine began operation in the 1960s as a surface project using the latest technology available. During the 1990s, the operation, located about 160 km (100 miles) west of Kimberley, South Africa, began its move as an underground mine. The earlier stages (Blocks 1, 2 and 3) of underground work at Finsch used open stope mining methods, also using the latest in technology. The mine began developing Block 4 in 2004. How-ever, studies on this level showed that block caving was a more efficient mining method than open stoping. It was during those studies that De Beers determined that Block 4 would be a good candidate for testing Sandvik?s automated truck haulage technology.

Jan 1, 2008