Search Documents

By C. L. Sainsbury

For 10 years, the author has been engaged in a program of geologic mapping of the Seward Peninsula, Alaska, for the U.S. Geological Survey. Initially, two 1:63,360-scale quadrangles were napped by traditional methods of traverses by foot and by tracked vehicle, supplemented by reconnaissance from a light aircraft owned and piloted by the author. Five summers were required to map those two quadrangles, which lie north of the tree lice in typical Arctic climate. In 1967, the project was reoriented toward the reconnaissance capping of four 1:250,000-scale quadrangles, with helicopter support to be used for cart of each of four summers amounting to about 45 hours time per support year. The light aircraft was use-,' to support the field operations. Over the year,, the aircraft was used in progressively more geologic tasks, culminating in 1970 with a successful field test of rudimentary devices made to collect soil, rock, and sediment samples while the aircraft remained airborne. Additionally, an attempt was made j- 1970 to prepare reconnaissance geologic maps entirely by the use of the light aircraft combined with foot traverses [fr??], the landed aircraft. Several such maps, prepared at the rate of about one 1:63,360-scale quadrangle per day, were checked from a helicopter by an impartial observer end were found to be sufficiently accurate for reconnaissance mapping when reduced to 1:250.000 scale.

Jan 1, 1971

By K. N. Han, M. C. Fuerstenau, T. B. Onlin

An investigation of the removal of finely divided silica, coal, and alumina particles less than 20,µm in size has been carried out using liquid fluidized and packed beds. The bed particles used included 48x100, 100x150, and 150>200-mesh silica, corundum, and ilmenite particles. Important variables examined included surface charge, flow rate, pH and amount of bed particles. Surface charge has been identified as the most important variable in this system. Van der Waals force also assumes a very important role in the recovery of fine particles in fluidized and packed beds. In addition to interaction between large and fine particles, interaction between fine particles themselves assumes an important role in the overall recovery.

Jan 1, 1987

By A. John R. Hart

INTRODUCTION In each given set of operational criteria for tunnel design, ground conditions dictate the selection of the most appropriate construction method and tunnel lining. The designer has the responsibility to choose or restrict the choice of the tunnel lining to insure that the final solution provides a cost-effective permanent construction which will require the minimum of maintenance and endure to the benefit of future generations. This Paper deals with some of the aspects of precast concrete tunnel linings, their history and development through the years. It does not purport to be a comprehensive review of all that has ever been tried or developed but, hopefully, a starting point to encourage discussion and development for the future. BOLTED LINERS As a result of anticipating a shortage of cast iron tunnel lining in 1936 when work was proceeding on London Transport's Central Line Metro, a design for the precast reinforced concrete bolted lining was born. The design took the form of the traditional cast-iron lining but with substantial concrete stiffeners to take the shield ram forces. This new lining was used to construct some 14,000 feet of running tunnel using a ring width of 1'8" which was the standard cast-iron width of the time. (Groves, G.L., 1943)

Jan 1, 1987

By Thomas E. Bruner

Today many small diameter tunnels are being constructed in Metropolitan areas and towns as transmission holes for utilities such as water, electricity, natural gas and sewage, to name a few. These tunnels function as utilities beneath the streets, highways, railways, and other structures where open-cut techniques are impractical for any one of a number of reasons. Many such bores range in diameter from 15 to 72 inches and in lengths from 100 to 500 feet. Auger drills with auger type heads have long been used to bore these "road crossings" as they are usually termed; however, many such crossings must be bored in rock with rock-boring heads. Rock with a compressive strength of 15,000 p.s.i. and higher seems to present the greatest challenge for the contractor. These rocks include most igneous and metamorphic rocks and some sedimentary rocks. In general, this grasps most granites, basalts, gneisses, slates, schists, quartzites, limestones, and cherts. In the past ten years boring machines have been developed and used to excavate road crossings through hard rock. Many crossings have been successfully excavated using these machines, and the degree of success has increased substantially in the last few years. A variety of machines have been built and manufactured to bore most rock in a range of diameters up to 72 inches. The machines vary in capabilities, size ranges, and designs but all perform the same basic task and function of boring horizontally. Incidently, here the term horizontal implies horizontal or within five degrees of horizontal. In addition, there is a wide variety of designs, sizes, and types of drill stems, joints, and pipe to meet the various conditions and

Jan 1, 1974

By D. Dolinar, T. P. Mucho

Horizontal stresses are caused by global platetectonic forces. During 1995 alone they were largely responsible for the closing of two longwall mines in the United States. This paper presents six case histories from Pennsylvania, West Virginia, Kentucky and Alabama. In each case, a mine encountered roof falls or difficult ground conditions at the headgate caused by horizontal-stress concentrations. The problems are detailed, and the control measures adopted are described. In most cases, nearby longwall panels without stress concentrations were trouble free. The paper also discusses detailed measurements that were made at two adjacent Pennsylvania longwalls. One headgate was oriented to avoid a horizontal-stress concentration, and the other was not. Eliminating the stress concentration dramatically reduced roof support loads and roof deformation. The paper concludes that proper panel orientation and sequence is the key to maintaining headgate ground control. The optimum orientation is not parallel to the maximum horizontal stress, as previously thought, but rather it is 20o in the stress shadow of the gob. Other stress-control techniques, including artificial support, are briefly discussed

Jan 1, 1999

By G. V. Henderson

Limestone and Dolomite quarries located near Salto-De-Pirapora, Arroia Grande Gaucho, Conde Francisco and Candioita probably represent the closest, major sources of high quality lime and cement grade carbonate rocks to the major population center of Sao Paulo Brazil. The nearest major city to most of the limestone - dolomite sources is Sorocaba and Palma. All of the mining properties visited during this study are located in the state of Rio Grande Do Sul at approximately -32 degrees south latitude and -52 degrees west longitude, southwest of the major port city of Porto Alegre.

Jan 1, 1981

By T. Yun

The process automation of coal production is one of the important component parts for achieving the modernization of coal industry. To realize the coal mining process automation serves the significant, function of increasing productivity, improving the quality control of raw coal, making efficient use of mineral resources, saving energy and is of great importance in enhancing the safe operation and improving the labour conditions as well.

Jan 1, 1989

By T. E. Wilson

An exploration bore core sample of coal ought to be reduced from its original cylindrical form to a particle size distribution and particle composition that reflects, insofar as possible, a process stream of? raw? coal it represents. Often, coal cores are reduced with a laboratory crushing machine, the product of which may not match the raw coal size distribution or size fraction composition. This study employs drop-shatter impact breakage followed by dry batch tumbling in a steel cylinder rotated about its transverse axis in order to characterize the core material in terms of first-order and zeroth-order breakage rate constants. These are indices of the propensity of the coal to degrade during excavation and handling. Initial drop-shatter and dry tumbling tests were done with synthetic cores, to reduce material variables and . conserve difficult-to-obtain coal cores.? Cores of three different coal beds --Illinois No.6, Upper Freeport, and Pocahontas No. 5 -were subjected to drop-shatter and dry batch tumbling tests to determine breakage response. Comparison of coal preparation plant feed with a crushed bore core and a bore core prepared by drop-shatter and tumbling (all from the same Illinois No.6 coal mining property) indicated that the size distribution and size fraction composition of the drop-shattered/tumbled core more closely resembled the plant feed than the crushed core.

Jan 1, 1998

By J. F. Stenebråten, W. P. Johnson

Carbonaceous material (CM) from the Barrick Goldstrike Mines, NV, was characterized with respect to its gold sorption (preg-robbing) and gold recovery behavior. The breadth of graphite peaks measured by X-ray diffraction were used to calculate crystallite dimensions (002) of the CM. The (002) dimension was found to vary inversely with preg-robbing activity and directly with gold-recovery behavior, indicating that the degree of graphitization (maturation) experienced by the carbonaceous material is correlated with gold-loss during ore processing. The inverse correlation of preg-robbing activity was improved when percent preg-robbing was regressed against (002) crystallite size and carbon content. The (101) crystallite dimensions of all samples were calculated from laser Raman analysis, and were not found to correlate with preg-robbing behavior of the CM. BET surface area and micropore size distribution results were affected by grinding history, negating comparison of these characteristics between samples.

Jan 1, 2000

By B. W. Cavender

Innovative mining and metallurgical operating techniques and processes can be identified and developed by analyzing changes as they occurs within the mine, plant, technology or industry. Sources of change to be monitored for innovative opportunities include unexpected successes or failures, incongruities between perceived and actual events, process needs, changes in perceptions and the development of new knowledge. Innovation can be organized, practiced and managed. The perception of change as an opportunity rather than a threat is mandatory, as is the systematic measurement of innovative performance. Innovation is enhanced by specifically designed policies regarding organizational structure and staffing, daily management practices and compensation and incentives.

Jan 1, 1996

By J. W. Merks

Applied statistics provides scores of powerful tests and techniques that are widely used and abused in science and engineering. The variance is the basic measure for variability, precision and risk. The formulas for the variances of the arithmetic mean and the weighted average are derived from the variance of a general function, as defined in probability theory. The requirement of functional or mathematical independence in probability theory translates into the concept of degrees of freedom in applied statistics. Geostatistics is the only variant of statistics in which functional dependence and degrees of freedom are irrelevant. This paper examines whether such basic elements of probability and statistics can be ignored with impunity.

Jan 1, 1997

By Lars Olaf Höglund

MiMi has been set up to be i) visionary, ii) strategic and iii) long-term. The planning as well as the executive phases involves industry, academia and authorities in close co-operation. MiMi focuses on improved, economically efficient management of mining waste, a challenge that requires combined and integrated research efforts across discipline boundaries. The MiMi programme is financed by the Swedish Foundation for Strategic Environmental Research (MISTRA) with support from the mining industry. The first programme phase covers the period 1997 - 2000, with intentions for additional phases. Planning, experience and results from the first programme period are highlighted. INTRODUCTION Most of the mining activities in Sweden takes place in the No

Jan 1, 2000

By N. Del Bel Belluz

Drilling underground in the Grasberg De-watering drifts has routinely hit water aquifers with high flow rates and pressures. Two types of holes are utilized; pilot-holes to probe ahead of the tunnel development to intersect aquifers ahead of the face; and de-watering holes to de-water rock formations that will drain water from the Grasberg pit and allow tunnel development to proceed safely. Recently, rates of 1050 psi static pressure have been recorded with flows from a NQ hole measured at 1350 gpm (US). The water flows can be slightly acidic, necessitating the use of stainless steel collar gear to resist corrosion. These rates were anticipated and contingencies were planned early to deal with these conditions. The collar gear is used to control water flows whereby the water is treated as an important resource. As a result, pm has established procedures to maintain safety of the drill crews, enable coring of the rock and to maintain safety of the miners who are driving the drifts.

Jan 1, 1998

By S. K. Sharma, D. A. Stanley

The US Bureau of Mines is investigating the fundamentals of the flocculation process. The objective of this study was to determine the effects of various physico-chemical parameters, namely, shear rate, polymer dosage, and polymer concentration, on floc growth and to determine the applicability of a model for predicting polymer flocculation behavior. A rapid in-line particle size analyzer was used to follow the progress of both the floc growth and the breakage as a function of time. A genetic algorithm (GA) was used to determine the unknown parameters in the model and to fit a curve to the experimental data. The results showed that the model reproduces the experimental data with only reasonable accuracy and that it was relatively insensitive to the parameters. Results of the flocculation study showed that increases in the polymer dosage had a greater effect on the time required to reach the maximum floc size than on the floc size itself: It was also determined that, given all the above parameters, the degree of slurry mixing during the flocculation process had the greatest bearing on floc growth.

Jan 1, 1995

By Egon Pohl, Peter Eckl, Friedrich Steinhäusler, Johanna Pohl-Rüling

RADON EXPOSURE AND CARCINOGENIC CELL TRANSFORMATION The highest radiation burden to miners is due to inhalation of radon and its short-lived decay products. The quantification of the risk associated with this radiation burden is complicated by modeldependent lung dosimetry, insufficient accuracy of past human exposure data as well as lacking knowledge about potential synergism of various carcinogens. Nevertheless, it is evident from epidemiological studies of miners that inhalation of elevated levels of radon daughters is correlated with increased lung cancer incidence (UNSCEAR, 1977). The situation is further complicated by the lack of reliable data on the biological variability of the latency period for the development of lung tumor under varying exposure conditions. At present information on variation with age is scarce, however, it is indicated that the excess lung cancer rate for workers exposed to high radon levels is considerably higher, if exposure occurs at ages over 40 years as compared to under 30 years of age (Sevc, Kunz, Placek, 1976). Furthermore, latency period is shorter by 6 - 7 years for smokers exposed to elevated radon levels than for non-smokers (Fry, 1976). Analysis of US- and CSR-uranium miner data revealed that the mean latency period is in the order of about 15 years (Jacobi, 1973). These uncertainties, together with medical diagnostic shortcomings, lead to the dissatisfying situation that at present the detection of radon induced injury of mining personal is primarily the assessment of the endpoint, i.e. radiation induced cancerous transformation of lung cells with typically less than 10% chance for recovery. Therefore it would be advantageous to develop practically applicable diagnostic aids to indicate already early precancerogenic changes of cell characteristics. This would permit the identification of specific population groups at increased risk for the development of lung cancer, thereby increasing the chances of more successful medical treatment. Despite continuous improvements in the reliability of test methods for the diagnosis of cancer cells there is still need for techniques, which enable the detection of transformed cells before the onset of invasion of the host organism. It is generally recognized that the transformation of a cell into a malignant state leads to a change of the cell surface, indicating a correlation between membrane-specific immunological properties and loss of growth control. Surface alterations on cells appear to be responsible in part for the malignant state and are not simply secondary effects of the transformation (Schnebli and Burger, 1973). Furthermore, membranes of cancer cells differ significantly from those of normal cells, particularly, in permeability properties (Rastogi, 1976). In dying cells, proteins, glycoproteins, peptides, aminoacids and their breakdown products are released, which block the permeation of the membrane itself. A mammalian cell can be considered as a 3-phase system (interior, boundary, environment) with the membrane forming a heterogeneous barrier between two subsystems. Under normal circumstances a difference of chemical potential is maintained on both sides of the membrane, causing an ion gradient across and fixed surface charges on the membrane. This results in a membrane resting potential (MRP) between cytoplasm and the bulk medium. It has been shown that MRP is a highly sensitive indicator for cellular reactions due to physical, chemical and biological agents, particularly whenever phenomena of transport and ion gradients as well as permeability are involved (Redmann, 1980). The primary interaction of the agent "ionizing radiation" with any form of living matter occurs at the cellular level. The component with the highest hit probability is the cell membrane. In the study presented MRP-changes of human cells were investigated with simultaneous measurements during irradiation and post-irradiation intervals up to six days. Furthermore, the suitability of MRP-measurements of human cells was tested as an indicator for early changes of cellular properties prior to the histological confirmation of carcinogenic transformation. EXPERIMENTAL METHODS Lung cells The biological specimen used were cultured human lung cells and human lung biopsy samples. Monolayers of lung fibroblasts (W138) were grown in petridishes using conventional culture techniques. In addition, transformed lung cells (W138SV13, subline 2RA) were used applying similar culture methods. All petridishes were incubated at 37°C and only cells in logarithmic growth phase were used. Freshly excised lung biopsy samples were obtained from randomly selected male and female patients (20 cases), where suspected or unclear malignancies were indicated by clinical or X-ray observations. At the time of sampling 80 % of the patients were or had been smokers in the past. The samples were taken by means of a stiff bronchoscope introduced into the trachea under local anasthesia with 1 % Novesinsolution (preparation with Atropin and Pantopen). This permitted the observation of both main bronchi down to the segmental bronchials. From each patient two tissue samples were excised from the mucusepithelial layer under visual control with fiber optics and transferred immediately into 1 % NaClsolution. One sample was taken from the suspected

Jan 1, 1981

By G. H. Thomas, M. C. O’Riordan, S. Rae

INTRODUCTION The British mining industry comprises 228 nationalised coal mines producing some 113 million tonnes of deep mined coal and employing 242,600 persons of whom 185,200 work below ground. There are in addition 174 small privately-owned coal mines employing 1500 persons underground and producing 1.5 million tones of coal. In the non-coal sector there are 108 privately-owned mines producing some 20 different minerals, including tin, wolfram, fluorspar, potash, rock salt, china clay, ball clay and fireclay. There are currently 4,100 persons employed in these mines of whom 2,346 are employed below ground. One mine producing potash employs 870 persons of whom 465 are underground workers. Since 1975 all matters relating to the health and safety of persons at work and of the general public who are exposed to industrial hazards have come within the purview of the Health and Safety Executive (HSE). The Mines and Quarries Inspectorate (MQI) is a constituent part of that organisation and enforces legislation applicable to all mines and quarries. The National Radiological Protection Board (NRPB) is a statutory and independent body that was established in 1970 to advance knowledge and provide information and advice about radiological protection. The NRPB has an agency agreement with HSE to provide advice and services relating to radiological protection, including protection against exposure to radon decay products in mines. There are as yet no statutory requirements controlling exposure to this source of radiation in Britain. Investigations for the presence of radon in British coal mines were begun in the mid 195Os. The concentrations found were of low order, typically around 2 pCi/l (Duggan et al., 1968). This was not surprising since big coal mines are well ventilated to control methane and airborne dust and it is now generally accepted that radon and its decay products do not constitute a health hazard in British coal mines. At one or two small mines where igneous intrusions were in close proximity to the coal workings, slightly higher readings were recorded. The MQI then commissioned NRPB to make investigations at metalliferous mines and in these much higher readings were detected. It was later agreed that the NRPB should undertake a survey of all non-coal mines in Britain to establish the extent of the problem. This survey was conducted mainly in 1973, (Strong et al.,1975) and follow-up surveys at various mines have since been conducted by the MQI. These investigations revealed that radon readings could be high in mines producing tin, haematite and fluorspar. Some small mines working other minerals in the same localities also showed high readings. More recently owners have been making environmental measurements at mines where there was some cause for concern. LEGISLATION AND RADIATION STANDARDS As a result of the survey work for MQI the Board in 1975 recommended an occupational limit of 4 WLM in a year from radon decay products together with a programme of radiological supervision (Strong et al., 1975). The MQI accepted the recommendation and advised employers and employees that the 4 WLM limit should be adopted. The limit corresponds to a concentration of 0.3 WL, equivalent to 30 pCi/l of radon-222 in equilibrium with the decay products, and was in accordance with an earlier recommendation by the International Commission on Radiological Protection (ICRP, 1959). ICRP recommendations are usually endorsed in Britain. It was recognised that some years would probably be required to achieve general compliance, and this is proving to be the case. Some confusion has been caused in Britain by the conflict between successive Euratom Directives on this and other standards of safety. As relative newcomers to the Community, we were not affected by earlier Directives, but the situation is different now. In 1959, the Commission of the European Communities provisionally recommended a maximum permissible concentration for radon-222 and daughters of 3 x 10-7 µCi/cm3, which corresponds to 300 pCi/l (CEC, 1959). The number was affirmed in 1962 (CEC, 1962) and reaffirmed in 1966 (CEC, 1966) but without any specification of the state of equilibrium. In 1976, the CEC again recommended 300 pCi/l, but on this occasion, the daughters were assumed to be present in the same quantities as in unfiltered air (CEC, 1976): this implies 40 WLM a year in poorly-ventilated mines. The formula is repeated in the latest version of the Directive (CEC, 1980), but the value is now said to be an interim one because it might not ensure compliance with the appropriate dose limit. ICRP (1955) recommended 300 pCi/l in equilibrium with the decay products in 1955 and reduced this value to 30 pCi/l for unfiltered air in 1959 (ICRP, 1959), endorsed it for equilibrium conditions in 1976 (ICRP, 1976), and held to it until 1980: these values imply respectively 40 and 4 WLM a year. The recent recommendation of the ICRP (1980) that the annual limit of intake for the decay products should be 0.02 J in a year corresponds to 5 WLM, but there is a rider that reduction should be made for exposure to gamma rays and long-lived airborne radioactivity. An allowance of 20% is suggested for uranium mines, implying 4 WLM a year for the decay products. The

Jan 1, 1981

By B. Pesic, J. E. Wey

Introduction One important class of manganiferrous ores is manganiferrous-silver ores. They occur in the oxidized portions of the silver deposits of the western United States. Silver is often associated with manganese oxides, which in some ore deposits are dispersed through calcite, causing the black color of the host rock, known as black calcite. Black calcites can occur in carbonate rocks (0.3 to 50 kg Ag/t) and in volcanic rocks (less than 30 g Ag/t). Silver mineralization associated with manganese oxides and black calcites can occur in veins (Hewett, 1968) or as disseminations (Graybeal, 1981). In the US, silver-bearing manganese veins are located in a broad arc that extends from southern Colorado to southwest New Mexico, southern Arizona, and southeast Califor¬nia (Hewett, 1964). Areas of disseminated silver-manganese mineralization include the Creede and Silver Cliff districts of Colorado and the Tombstone and Hardshell districts of Arizona (Graybeal, 1981). These deposits are also characterized by significant amounts of silver halides - cerargyrite (AgCl), bromargyrite (AgBr), and iodargyrite (AgI). Black calcites are also common in these deposits. Oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. In the past when these ores could not be smelted, they were treated generally by cyanidation at very low efficiency. The US Bureau of Mines (USBM) studied the problem of treating silver-manganese ores in the early 1920s (Clevenger and Caron, 1925). It was found that the refractory silver in the original ore was insoluble in all the common solvents for metallic silver and its salts. The conclusion was that to obtain the highest recovery of silver, all the manganese had to be dissolved or the higher oxides of manganese reduced to manganous oxide. More recent results from treating refractory silver¬manganese ores were given by USBM (Scheiner et al., 1973). The silver ores from Candeleria District, NV, and Round Mountain District, CO, were investigated. Electrooxidation experiments recovered only 34% silver with minor amounts of manganese dissolved. Sulfurous acid pretreatment followed by cyanidation revealed that silver extracted was proportional to the amount of SO2 used. A similar approach, using sulfurous acid pretreatment followed by cyanidation, was also proposed by Rhoades et al. (1984). Hazen Research Inc. performed extensive testing on silver and manganese dissolutions from Ag-Mn ores obtained from the Candeleria and Round Mountain ore deposits. The methods examined were direct cyanidation, pretreatment with sulfurous acid followed by cyanidation, malonitrile leach, and leaching with ammonium hydroxide-sodium thiosulfate under slight oxygen pressure. The results were not satisfactory. The importance of the vast reserves of Ag-Mn ores and the lack of an efficient method to recover these metals warranted a search for new technologies. One novel method for extraction of these metals is treatment of Ag-Mn ores with acidified thiourea solutions. Preliminary results of the leaching of silver and manganese from Ag-Mn ores were very encouraging (Pesic, 1984a) ; thus, it was decided to examine the new lixiviant in more detail. Experimental Ore from the Round Mountain District was studied. It was crushed, ground, and dry sieved into monosized fractions in the range of 16 to +400 mesh. The ore composition was about 90 g Ag/t and 3% Mn, depending slightly on size. The leaching experiments were performed in apparatus described elsewhere (Pesic, 1982 and 1984b). All experiments were performed at constant temperature conditions. The leaching residues were analyzed for silver and manganese. Atomic adsorption was used to analyze the solution samples and fire assaying to analyze the leaching residues (for silver). The standard experimental conditions are given in

Jan 1, 1987

By John McMorran

An open pit mine design system should have the characteristics of being flexible, versatile, and simple. All of these characteristics are necessary for producing a dynamic mine design. In other words, a design that can be improved, updated, and implemented. Flexibility is an important characteristic due to changing times. For example, the effects of a changing economy, increased knowledge of the mineral deposit, or improvements in mining technology can result in a considerable, if not a complete change in the long range mining plans. Since the short range mining plans are based on the long range mining plans, they will-also be effected. Also, it is very important to validate the information used in the design or the design itself. This means the system should have the flexibility of being able, not only to detect, but to correct errors. Versatility is another important characteristic of a mine design system due to the wide range of situations that may appear. First, a design system must be able to handle both long and short term planning. This is necessary because of the variability in the definition of a time range. Second, a design system must be able to handle different types of deposits. Special emphasis must be placed on this issue, because many deposits, if not the majority, do not fit predefined categories such as bedded, massive, or roll-front, etc . . . Furthermore, the true test of the versatility of a design system is not only the ability to create an ultimate design but also to schedule sequences for this design. Thus, the versatility of being capable to design with a variety of time ranges, variety of deposit types, and scheduling are all important characteristics of the design system.

Jan 1, 1982

By J. K. Wolski

This paper addresses the effects of using jet fans as booster fans in mine ventilation networks. A method was developed to determine the pressure generated by jet fans using the momentum theory. The influence of a reduction cone and other ventilation parameters on the jet fan pressure was analyzed. Verification experiments conducted in the Waldo Mine are described. Examples are given to demonstrate the conditions for the effective use of jet fans.

Jan 1, 1998

By H. Kiyama

In order to further elucidate the mechanisms involved in autogenous grinding, the fracture of rock specimens in free-fall impact was studied using the theory of elasticity. Stress distributions in rock specimens under various conditions of impact were analyzed and the conditions for failure were examined in relation to the compressive and tensile strength of rock. The energy equation derived for autogenous grinding coincides basically with Lewis' generalized formula or Oka and Majima's formula, and it is sufficiently general to incorporate all of the three older theories, viz; those of Rittinger, Bond and Kick.

Jan 1, 1972