Search Documents

By R. P. King

Direct observations of intergranular fracture during comminution are very difficult to make. The best indirect method is based on the measurement of interphase area before and after comminution. If intergranular fracture does not occur, the interphase area should be conserved during comminution, but it should decrease if significant amounts of intergranular fracture occur. The interphase area per unit volume can be determined by image analysis from measurements on sections of the unbroken ore and on sections through the particles after comminution. However, the measurements must be corrected for the effects of image resolution on the measured phase and particle perimeters. A correction procedure was developed, and the true interphase perimeter per unit volume was measured before and after comminution in a sample of chromite-serpentinite ore and two samples of Witwatersrand pyritic quartzite. The pyritic quartzite showed no significant evidence of grain- boundary fracture while the chromite-serpentinite showed a significant decrease in interphase area per unit volume of chromite, indicating that intergranular fracture occurred.

Jan 1, 1992

By R. Bouzaiene

In the paper presented by F.W. Brackebusch on the “Basics of paste backfill systems,” paste fill was presented as a backfill process that offers many advantages over other alternatives such as hydraulic fill and rockfill. It was observed, however, that the mechanics of paste-fill transportation in pipelines is not fully understood and that the success of its implementation in practice depends on the precise control of the proportions of fines, aggregates and water in the mixture. The author emphasized the necessity for laboratory and full-scale testing to determine the suitability of a material to be used as paste fill. Although experimental testing is definitely an important operation in the design of a reliable paste fill, advances in the understanding of the fundamental laws that govern paste flow in pipelines are equally relevant. Ideally, the results of such efforts would provide predictive models for the rheology of the paste and the corresponding pumping-energy requirements. In an attempt to achieve this objective, an ongoing research program has been active at McGill University’s Department of Mining and Metallurgical Engineering.

Jan 1, 1995

By Carl D. Broadbent

The goal of slope mechanics is to achieve efficient and safe pit slopes. In the case of ultimate mine slopes the objective is to minimize the stripping ratio by steepening the slopes to their maximum stable limit. On the other hand, the inclination of working slopes is normally established by operating space requirements and the function of slope mechanics should be the continuous surveillance of slope conditions to assure long-term stability and to provide timely warning of impending slides so that corrective measures may be incorporated in production planning. In 1956 Kennecott instituted a program to provide the resources necessary to develop and maintain a slope mechanics capability, including technical knowledge, engineers, and instruments. Although the goal has not been fully achieved, very significant progress has been made. Other papers (3, 4, 7, 8, & 12) have described the purposes and detailed results of the most recent study carried out at the Kimbley Pit. The study has provided valuable experience and has given the industry a three dimensional picture of the stability variables that influence a mine slope. The study has better defined those areas which require further investigation and has indicated those design and analytical techniques which can be used with confidence. In effect, the study has paved the way for the next step; that of refining the design process and applying it for profit.

Jan 1, 1968

By Wayne F. Crockett, Martin H. Col

Gold, as a precious metal, has been sought for several thousand years. During this time economics have generally determined whether or not a deposit is minable. Today, few would spend $500.00 or $1,000.00 to produce one ounce of gold, yet most gold deposits currently being mined would have such costs if they were mined using the methods of the 18th century. Innovation has been the key to success in the world of mining. We are constantly having to look for new ways to mine deposits of lower grade, at greater depths, or with higher stripping ratios. The mining of placer gold deposits has always been subject to the volatile swings of the world price and the constant rise in production costs. The rise in costs is compounded by the drop in overall ore grades. Occasionally, a major technological innovation will dramatically reduce the costs of placer mining to allow previously marginal or unminable deposits to be mined at a profit. The continuous bucketline dredge was the last such major innovation in the gold placer mining. The continuous bucketline dredge has allowed large volumes of placer deposits to be picked up and processed on a continuous basis. Unfortunately, as the overall grade of the deposit declines, it becomes impossible to process enough ore to pay for the operating costs. There are many gold deposits around the world waiting for the next technological innovation that will allow them to be mined. One such deposit has been the Grey River deposit near Greymouth in New Zealand. The deposit contains gold reserves of 8992 kg, yet the deposit has been sitting idle for many years because the average value

Jan 1, 1988

By Pradip

Chelatang agents, because of their metal specificity, can function as effective mineral processing reagents. A brief review of the work carried out in this area is presented. Some of the salient features of mineral flotation and flocculation with chehting-type reagents, such as bulk us. surface chelation, the role of pH, mineral solubility, solution chemistry of reagents, and temperature, are illustrated with appropriate examples. The problems associated with the commercialization of chelating reagents for ore beneficiation and the research efforts required in this area are also discussed.

Jan 1, 1987

By M. T. Holroyd

Digital computer applications to minerals exploration remained largely an experimental alternative to manual techniques until well into the 1960's. Due to the high cost of computer time, and the lack of digital data and appropriate software, the most favoured applications in the early days were computationally intense tasks - those which produced the most results with the least demands for programing and data input, e.g. forward modeling. When large digitisers and plotters became affordable, the computer took over simple labour intensive tasks such as data transcription, and when software caught up, more complex tasks such as contouring. Digital data acquisition systems and superminicomputers made total computerisation of geophysical compilation and cartography possible and affordable. Applications continued to develop into areas of much greater logical complexity. Software, the new labour intensive process, still lagged behind. The microcomputer made computer applications potentially available everywhere to everyone. Desk-top micros as powerful as the minis of ten years ago can take on any geophysical exploration task currently done by computer - when the software becomes available.

Jan 1, 1989

By Gary B. Hemphill

The 345 km long Taiwan High Speed Rail Project will connect the island’s two most populated cities, Taipei and Kaohsiung. Kaohsiung is the world’s third busiest port. The 23 km of alignment on Contract C230 requires the construction of 5,879 m of shallow mined tunnels ranging from 137 m to 1,285 m in length. All nine of these tunnels are mined using NATM methodology. Two of the tunnels, T01 and T08 are in the Toukoshan Formation. This paper will discuss the mining methods, ground support design, and the instrumentation installed to monitor and verify its effectiveness in the two aforementioned tunnels.

Jan 1, 2003

By B. H. Kaye

Particle-size Distribution Specifications for Particulates. Feed to and finished products from size-reduction operations are defined in terms of the particulate sizes involved. It is also well to know whether the ultimate individual particle is being measured, or, if any aggregation or agglomeration of particles exists, whether this has been created by the size-reduction operation. The most complete description of a powder is given by its particle¬size distribution. This can be plotted in terms of cumulative percent oversize or undersize in relation to the diameters of particles, or it can be plotted as a distribution of the amounts present in each unit of diameter against the several diameters. It is common to employ a weight basis for percentage, but there are some data in the literature where frequency, or number of particles, is used. The basis of percent¬age, whether weight, frequency, or some less commonly used factor, should be specified, as also should be stated the diameter, its units, and preferably whether determined by sieve, settling velocity, or other¬wise. Fig. I presents two sets of distributions-ore cumulative and the other in unit intervals. The slopes of the 5-µ intervals of the cumulative curves are converted to percent per micron and plotted as a block, or histogram, from which smooth curves are derived. Powder A has a narrower, or tighter, size range for the bulk of its weight than powder B. Both materials have the same weights below and above the size marked by the arrow. Simpler treatments of distribution are possible. In some cases the significant value is the top size. Since the 100% point is dubious, some amount, as 95 or 98%, so specified, can be called top size. In other cases the percent on some sieve helps define coarseness. Merely stating that all, or all but a small percentage, passes a given sieve is inadequate for defining the true fineness or a material. Complete parti¬cle-size analysis to show the distribution is essential for most compari¬sons and calculations. Particle-Size Equations. A number of equations have been pro¬posed to correlate the quantity of a particulate material with its parti¬cle size to obtain a distribution relationship. 's 19 In the literature it is often assumed that a powder must follow some distribution, such as the Rosin-Rammler-Bennett:20, 21

Jan 1, 1985

By George D. Roberts

Dams are constructed to retard the flow of water or debris; therefore natural forces are constantly at work to remove such obstructions. To circumvent nature and avoid expensive trouble with a dam requires thoughtful far-sighted planning, careful construction control and vigilant periodic inspections to detect and repair deterioration at its inception. Although the factuality of the foregoing statements is apparent, all too many have failed to consider them in the past as will many in the future. "The economic, but safe construction of dams calls for the highest order of technical knowledge, practical experience and sound judgment." (1)

Jan 1, 1967

By S. Bhattacharaya, S. Aich, B. K. Nandi

"At present scenario, there has been an increasing demand in the usage of blend coal in power sector; regardless of how, specific knowledge on burning and ignition characteristics and their interactive effects is stingy. In this work a detailed investigation was therefore taken up to study in detail the combustion characteristics of selected coal samples and their blends. Certain parameters were believed to have significant effects on combustion characteristics of individual coal and their blend. Major parameters identified for this purpose included proximate analysis, combustion conditions, heating rate, reaction regions, blending ratios, ignition condition, reactivity (or reaction rate) and burnout temperatures. With the help of these parameters, thermal features and reaction kinetics of the individual and blended samples were investigated through a qualitative and quantitative thermo-gravimetric analysis of two different individual coals and their blend carried out in an oxygen atmosphere from ambient to 800 0C at a constant heating rate of 10 K/min. A significant difference in terms of rate of mass loss with temperature correlated from Arrhenius expression along with coal-coal blend interactions and deviation from their expected behaviour, have been observed between the kinetics of individual and blend samples, the latter showing better ignition performance and comprehensive combustion phase. It was also found that particles having the lowest percentages of volatile matter and ash could possibly be blended with particles having high ash and volatile matter to meet the required burning condition which can be effective in terms of cost savings, improved fuel economy, reduced undesirable exhaust emissions and improved safety of coal burning equipment. Experimental results further indicated that individual samples and coal blend samples have different combustion features in terms of residue left, peak temperatures and activation energies. Thermodynamic activation parameters such as activation energy, pre-exponential factor and order of reaction were computed from the thermal data using the modified form of non-isothermal methods. INTRODUCTION Coal has been the most significant source of energy for India and would remain so at least for the next few decades. About 60-65% of the electricity produced in India is from coal fired power plants. Indian coal is of drift origin and of high ash content. Ash content of the coal burnt in power plants in India is in the range of 30-45%, most of it being Run-of-Mine coal. Most of the power plants in India source their coal from number of mines, most common being multiple sourcing. Usually coal from each source [1] is burnt separately. For various reasons mostly associated with logistics, burning of blended coal is rarely practiced. Blending of coal is practised mainly for improving the quality of available coal and meets the shortage of coal supply. Blending technique is generally practised in power industries to reduce the cost of power generation along with mitigating combustion performance or slagging problem ensuring consistency in as fired coal quality and also for environmental compliance. Blending good quality imported coal can improve coal quality and helps in preserving indigenous coal resources for longer period [2]. Use of blended coal shall reduce load on all boiler components (Mill, CHP, Boiler, AHP) & reduce O&M cost and increase the availability. The main purpose of blending is to get a blended as fired coal having ash, volatile matter and gross calorific value close to design coal and the two coals are to be blended in such ratio proportions that resultant coal blend have desired ash, volatile matter and gross calorific value [3]. For a coal to be blended certain parameters have to be considered to get compatibility with respect to combustibility ( Burn ability) of coal, grindability ( HGI), ash fusion behavior, swelling characteristics of coal, need to be checked"

Jan 1, 2017

By W. Robert Rose, Randall Pyper, Carlos Mirabal, Jaime Eguivar

In 1984, work was started to determine the viability of heap leaching silver-containing waste dumps from Cerro Rico near Potosi - Bolivia, at an elevation of 4300 meters (14 100 it.). The result today is an unusual heap leach utilizing fine crushing, grinding, and agglomeration to process 1000 tonnes per day of ore containing 200 g/tonne silver. The unique metallurgical, economic, and political factors will be discussed which led to the decision to build a heap leach rather than a conventional agitation leach plant. Capital and operating costs will be given along with some of the uncommon process design and equipment problems encountered while developing the operation.

Jan 1, 1990

The objective of this study is to classify ore and waste in a selected mine. The support vector machine, was used for the classification purpose, is applied to a zinc ore body in a skarn deposit located in the central region of the Peruvian Andes. The input parameters used for the model are spatial coordinates and the lithological information of the ore body. The input data was divided into training and testing data sets and the performance of the model was tested using the testing data set. The results show that more than 76% of the data could be properly classified by this method. The ore waste maps of the deposit was then developed using SVM model. From the result it was observed that a comparatively very few number of cells classified as ore. The ore is concentrated in small lodes at the middle of the volume of study, and not uniformly distributed throughout the study area. The lithological map of the deposit was also constructed as it was used as an input parameter for the SVM model. The indicator kriging was used for generation of lithological map of the ore body. Key word: Ore waste classification, Support vector machine, Indicator kriging, Confusion matrix.

Jan 1, 2008

By M. Tomono

Harima Works is operating as the zinc and lead simultaneous smelter utilizing the imperial Smelting Process. The smelter commenced its operation in 1966 with designed capacities of 3500 t/M of zinc and 1500 t/M of lead. After that, owing to the results of progressive developments and improvements in operating efficiency and equipments, it has doubled its production figure. This report reviews our recent developments carried out from 1983 to 1985. Firstly, the furnace bottom design was modified for the purpose of reducing carbon consumption ratio. As a result, shaft operating condition has been satisfactory and carbon consumption ratio was improved by 2%, in addition, furnace zinc production was increased by about 8%. Secondly, the oxygen enriched operation at sintering machine was tested from July 1984 to June 1985, in order to increase the sinter productivity, and to solve the capacity imbalance between sinter plant and ISF. As the test result, it was found out that sulfur elimination rate was increased by approx 10% with the oxygen enrichment of 500 Nm3/hr.

Jan 1, 1986

By Paul M. Jr. Musgrove, Donald C. Moore

Conventional Smelting Practice Conventional copper smelting practice varies from smelter to smel¬ter, but generally consists of some or all of the following unit processes: roasting, smelting, converting, and fire refining. Roasting. Copper sulfide concentrates can be smelted directly or after an initial roasting step. Roasting is used in some smelters because roasting prior to smelting increases smelting capacity, less energy is required to melt hot roaster calcines than wet sulfide concen¬trates, roaster off gases are high in Sot concentration, 5-15% SO2, and some volatile impurities are removed from the concentrate prior to smelting. However, many smelters do not use roasters, because the problems associated with handling hot dry calcines outweigh the advantages mentioned. Concentrate roasting is performed in multiple hearth or fluid bed roasters. If the moisture is low, roasting can be performed autogenously, usually at 500-600°C. High roasting temperatures are avoided because excess oxidation of the iron compounds may lead to magnetite formation. Magnetite is detrimental to reverb operation because mag¬netite can combine with refractory minerals to form a highly viscous slag. This slag prohibits efficient matte-slag separation and leads to excessive copper losses. Also, magnetite can settle through the matte layer, deposit on the furnace bottom, and consequently reduce furnace capacity. Roasting is carried out only on sulfide concentrates prior to smelt¬ing in reverb or electric furnaces. For smelting processes, such as the flash and continuous that rely on the exothermic heat of oxidation of the sulfur minerals, roasting is not practiced. Reverberatory Smelting. The predominate copper smelting fur¬nace for the past 50 years has been the reverb. These furnaces are typically 100-120 ft long, 30-35 ft wide, and 12-15 ft high. A typical furnace layout is shown in Fig. 2. Refractory brick linings cover all internal surfaces of the furnace. Originally the flame was directed to reverberate or reflect off the furnace ceiling and melt the feed material. Current practice is to direct the flame down the furnace length to melt the concentrate. A method of charging the concentrates or calcines, generally along the side walls to minimize refractory erosion, is incorporated in the furnace design. The copper concentrates, calcines, and fluxes charged into the reverb undergo a series of complicated reactions as the temperature of the mixture increases. The reaction of the iron and copper sulfides with the oxygen in the furnace produces a molten Cu25-FeS mixture called matte. Copper smelting metallurgy is based on the fact that sulfur has a greater affinity for copper than for iron and most other common metals. Therefore, in a system containing copper, the copper will preferentially remain as a sulfide compound until all of the other metals have been oxidized. The oxidized metals combine with silica to form a silicate slag that floats on the matte and is removed from the system. Reverberatory furnace smelting chemistry can be approximated by the following chemical equations: FeS2 + O2 - FeS+ SO2 (1) The formation of FeS ensures that any copper present other than as sulfides will be reduced by the relationship: CuO2 + 2FeS + O2 - CuS + 2FeO+SO2 (2) or 2Cu +FeS - Cu2S + Fe (3) As the molten charge travels down the furnace, continued oxida¬tion of the iron minerals and sulfurization of the copper minerals occurs. When all of the copper has been converted to sulfides, the iron sulfides can then be further oxidized as: FeS + (3)2 O2 FeO + SiO2 (4) The FeO reacts with the silica added as flux in the furnace charge. A simplified equation is: FeO + SiO2 -FeO SiO2 (5) The iron silicate slag formed is skimmed from the surface at the end opposite the burners. The copper content of reverb slag is usually less than 0.6% Cu and is discarded. Matte is removed along the side wall and is taken to the converter for oxidation of the remaining sulfur and iron. The main objectives in reverberatory smelting are to produce a molten Cu2S-FeS matte containing 30-60% Cu and a throwaway slag. Production of matte permits complete conversion of all copper minerals into copper sulfides, which can migrate because of specific gravity differences, through the lighter slag layer. Also, the molten matte droplets collect the noble metals, gold and silver, as the matte settles in the furnace. The large settling area of the furnace provides enough separation time to produce a low grade slag, which can be discarded without further processing. High heat losses are associated with reverberatory smelting be¬cause of the large volume of gases sweeping through the furnace. Therefore, an outside source of heat is required to keep the smelting reaction going. Natural gas, fuel oil, or pulverized coal are used as this heat source.

Jan 1, 1985

By F. B. Micheli

Introduction and Historical Background Although both sluices and devices using a simple flowing film are among the oldest known methods of concentration, they are still extensively employed in a variety of situations where they are not only efficient but also have a low operating cost. More particularly, they are valuable for making a bulk concentrate of high specific gravity minerals from alluvials and beach sand and in upgrading low value ores. The antiquity of some of the basic concepts can be seen in the fact that they are found in Agricola's De Re Metallica which was published at Basic in 1546, while in 1602, Carew114 gave a fairly clear account of tin ore dressing in Cornwall in which grass turves were used to catch the cassiterite. This is perhaps one of the forerun¬ners of the blanket strake. The planilla of Mexico, the lanchute of Malaysia and the old Cornish box huddle are also descended from these early strakes. In fact, a sluice with holes in the bottom for concentrate discharge was shown by Agricola, not unlike the principle used in the plane table and the lamflo sluice. The convex huddle for the treatment of sandy material appeared about 1848 and the concave form eight to ten years later. For the treatment of "slime" sizes, wooden dead frames which were manually worked were used in Cornwall for many years but gave way to the automatic water-operated type in 1860, and even a mechanically tilted frame was described by Henderson115 in 1857. Theoretical Considerations The behavior of solid particles in suspension depends to a great extent upon the pulp density and the size of the suspended particles. In a fairly dilute suspension, such as that normally used when dealing with small particle sizes, the behavior of particles in a flowing film results from two effects. These are the lateral displacement, which is determined by the time taken for each particle to penetrate the flowing film and reach the solid surface, and the resistance offered by each particle to further displacement after it has reached this surface. The initial penetration through the flowing film depends on the size and specific gravity of the particle and the thickness and viscosity of the film. As a result the smaller particles will migrate further before their movement is retarded relative to larger particles of the same specific gravity. The behavior on reaching the solid surface de¬pends on whether there is a single particle layer or, as is more often the case, a multiple layer or thin bed of material which is sufficiently dilated, permits the penetration of higher specific gravity grains. Thrust of Flowing Films. When a thin film of liquid flows over a plane solid surface, the layer next to the surface remains at rest but the velocity of the film increases with the distance from the surface and becomes a maximum near, but not quite at, the free surface. Therefore, a particle in suspension in such a film is acted upon by a greater force near the upper part of the film than at the lower part, resulting in an overturning effect. After a particle reaches the separating surface or an accumulated densely packed bed of other particles, the liquid flow causes it to move downstream by rolling, sliding, or by a movement involving alternating suspension and deposi¬tion (saltation). In rolling and sliding, which are brought about by a substantially noneddying stream, the large submerged particles are acted upon to the greatest extent and they move more rapidly than smaller ones, notwithstanding their greater mass. When two particles of the same size but of different specific gravity are considered, the higher density one moves more slowly by reason of its greater mass. As a result the particles tend to become arranged in the manner shown in Fig. 29. If any particle is so large as to stand above the water surface, the transporting force on such a particle, although the maximum available, will have less effect than that on a submerged one. Such large grains are therefore carried a lesser distance. Fluid Velocity in a Flowing Film It can be shown that if y is the distance within the flowing film from the interface, the fluid velocity v' at this point is given by IIn this equation p' is the fluid density, g the acceleration due to gravity, a the viscosity, a the angle made by the film to the horizontal, and 0 the film thickness (in cgs units). Furthermore, the volume Q of fluid per unit time and unit width is related to the film thickness and can be calculated, since which upon integration gives Consideration of the velocity v' (Eq. l) and the terminal falling velocity µ derived from Stokes law enables the horizontal travel dz in time dt to be calculated as follows: Again integration and substitution of Eq. 3 gives In this equation, z is the distance travelled before a particle of density p at the top of the fluid film has settled on the concentrating surface. From these expressions it can be seen that the depth of the flowing film varies as the cube root of the volume of fluid and inversely as the cube root of the sine of the plane surface inclination. Similarly the distance a particle can travel before reaching the surface is directly related to the quantity of fluid and its viscosity. The viscosity of pulp is greatly increased by the presence of near colloidal particles and consequently the penetration of the somewhat larger grains through the flowing film is retarded, resulting in them being carried further across the concentrator deck. Obviously this effect can be reduced by prior removal of some or all of the ultra¬fine particles. The detrimental effect of kaolin on the separation of fine ferrosilicon from quartz has also been demonstrated by Johnston,116 the relationship between viscosity and efficiency of separation being shown in Fig. 30. The pH value also has a very marked influence on the viscosity and the use of acid mine water, for example, can increase viscosity materially and thereby result in lower efficiency. Dilation of Multi-Particle Systems Except during washing (when a single particle layer may exist) concentration usually takes place in a bed of particles which is partially dilated or stirred by eddy currents. The extreme case is seen in various forms of the sluice where the flow of water and the presence of riffles combine to create a fluid bed in which reverse classification takes

Jan 1, 1985

By Estban M. Domic

The modem copper industry presents an excellent opportunity for the application of clean, environmentally friendly techniques using currently available hydrometallurgical technologies. This paper briefly reviews key events in the development of modern hydrometallurgy in Chile. Discussion is given to those prominent events whose impact continues to be felt on most projects currently underway. Mention is also made of the foundations of heap leaching technologies, preceded by agglomeration and acid curing, known as the T.L. Leaching Process, the cornerstone of more recent developments. A review is also presented of the leading copper hydrometallurgy projects of the 1990s. A list of those projects, their tonnages and the estimated date of implementation is provided. The conclusion provides an overview of developments in research and the trends in the implementation of copper hydrometallurgy projects in Chile for the coming years.

Jan 1, 1998

By Gopalan Ramadorai

This paper presents a review of halogen solvents used in the processing of precious metals. Reagents of widely varying chemical structures, such as chlorine gas, calcium and sodium hypochlorite, chlorine dioxide, iodine and bromine have been used for precious metal extraction. None of these chemicals are a replacement for cyanide: however, each of these chemicals present an opportunity for use in processing a specific type of ore. The ore and chemical must be matched to each other for success. Recovery of metal from the leach solutions also offers challenges.

Jan 1, 1994

When exploration shows a mineral deposit to be of importance, the subsequent work of defining the limits or boundaries of the ore body and preparing it for the extraction of the mineral is termed development (Young, 1946). In underground mining, development also connotes the work that is involved in opening up a deposit preparatory to stoping or productive operations. In this section, mine development is defined to include all studies and operations that will enable a sound evaluation of an explored ore body from the technical and financial standpoints. Though the ultimate objective of all mine development activities is the same, the scope and detail of these activities vary depending on the type of ore body (e.g., flat bodies, lenses and sheets, massive deposits, narrow veins, and bedded deposits), and the method of working the deposit (e.g., under- ground or surface methods or a combination of both of the methods). Therefore, the various contributions in section 3 address such topics as long-range planning, feasibility studies, and valuation for many types of ore bodies and different mining methods. This introductory review is divided into three major parts. In the first part, long-range planning aspects are briefly discussed with .an emphasis on current trends that affect mine planning. In the second part, an overview is provided of the contents in the mine development and valuation section. In the last part, remarks are made on the status, scope, and future of quantitative and computer methods in mine planning and development.

Jan 1, 1979

By Pieter C. van Aswegen, J. A. Brierley, C. L. Brierley

The bacterial-oxidation (BIOX®) process for the pre-treatment of refractory ores for gold recovery is marketed by BlOMlN Technologies S.A. The process was originally developed by GENMIN who is still providing testwork, design and commissioning assistance to BIOMIN. Since 1986 three BIOX® plants have been commissioned by GENMIN. A further two plants will be commissioned during 1993 and 1994. The commissioning and operational experiences from these plants are described in the paper.

Jan 1, 1993

By C. J. Hall

The simplest natural ventilation cycle is similar to a Joule or Brayton cycle. This comprises two reversible adiabatic processes in the shafts and constant pressure processes underground and on surface. The thermal efficiency of such a cycle is given by the temperature increase in the downcast shaft divided by the absolute temperature of the air at the bottom of the downcast shaft, and is independent of the temperature increase underground. This efficiency is comparable to the Carnot efficiency, which is the greatest possible value between constant temperature reservoirs, source and sink. Two variations of the Joule cycle are investigated, using numerous work examples. In the first, dry air is used as the working substance, a fan is provided at the top of the upcast shaft, and various mass rates of flow are used with frictionless shafts and a constant resistance value in the horizontal mine workings. The lost work less the fan work gives the natural ventilation work, and this divided by the enthalpy increase in the workings gives the thermal efficiency. The thermal efficiency increases dramatically with mass rate of flow, although the enthalpy increase remains constant. This appears to violate the second law of thermodynamics, since the frictionless case has a Carnot efficiency. When the lost work is added to the enthalpy increase, however, the efficiency decreases slightly from the Carnot value, to conform with the second law. This increase in efficiency with mass rate of flow is often referred to as the reheat effect, although the air is not heated. The second investigation is similar to the first, except that the air entering the downcast shaft contains a small amount of water vapor, and there is evaporation in the mine workings only, until the air entering the upcast shaft is saturated. There is, of course, condensation in the upcast shaft. In this case, it is not possible to calculate the Carnot efficiency, but the thermal efficiency is 20 to 40% of the similar dry air values. This decrease is much more than can be accounted for by the larger value of specific heat for water vapor. In addition, the natural ventilation work is almost constant with increased mass rate of flow, and the thermal efficiency based on heat addition tends to decrease. The thermal efficiency based on heat and lost work decreases in conformity with the second law. The reasons for the differences in behavior between dry and moist air are not readily apparent.

Jan 1, 1991