Search Documents

By W. A. Hockings

This report describes a computer program for the solution of material balances in complex mineral processing flowsheets. The program, which is entitled MBS Metallurgical Balance System), evolved as the culmination of a series of material balance programs whose development began in 1967 at the Institute of Mineral Research, Michigan Technological University. The need for such a program became evident when the Institute became heavily involved in a large number of short-term pilot plant projects. Calculating material flows from analytical data by means of the standard two-product formulas grew increasingly difficult and time-consuming as the complexity of the flowsheets increased and as choices between conflicting analytical values had to be made. It was recognized that what was needed was a program that would assimilate all of the available data and calculate mass flow rates so that steady-state inputs and outputs would balance at each point in the flowsheet. Such a program should be capable of handling underdetermined, overdetermined and mixed systems, and when the given data are inconsistent, the program should adjust the data in such a manner that the adjustments are minimized. Missing analyses should also be calculated whenever possible. In addition to solving material balances, the program should be convenient to use and print out the results in a useful form. Thus, the inputting of data should be simple enough to be handled by relatively untrained personnel with diagnostic messages being printed out to identify errors and anamolous data when they occur. Most importantly, the program should produce well-formatted output which can be directly included into a report without the necessity of retyping. The proper spacing of table titles, column headings and the ability to control the columns being printed are important features in this respect.

Jan 1, 1977

By N. Careddu

In recent years, slabs with a rough surface have captured a large share of the ornamental stone market. However, the main technologies used for this type of treatment are based on mechanical shock (bush-hammering) or thermal treatment (flaming or flame-finishing). These traditional technologies are widely used, but have many limitations that decrease their usefulness. The purpose of this study was to develop a technology that enhances the natural colors of the rock and produces a rough surface without compromising its mechanical characteristics, in contrast to traditional technologies. This report shows the technical, economic and aesthetic results obtained with a new water-jet treatment and compares it with competing technologies.

Jul 1, 2010

By John C. Draper

[Duquesne Light Company's three power plants in western Pennsylvania are now receiving high BTU clean coal from a new coal preparation plant. When burning coal from this plant, particulate emissions are greatly reduced and the sulfur content of stack ace descend. The cleaner coal also leads to more effecting overall operating of the power plants because of less bulk handling of fuel and ash. Environmental improvement is an important benefit of the cleaner, more complete combustion.]

Jan 1, 1976

By C. C. Muir

At the outset, I believe reference should be made to comparatively recent world developments in copper which have an important bearing upon the Canadian position. COPPER SITUATION No one can doubt the marked change for the better compared with not so long ago when less than adequate attention was paid to marketing and to uses of the metal. I need not show you graphs of world copper prices, which except for relatively brief periods and war conditions were, until about three years ago, not unlike the topography of the Canadian Rockies. There remain, of course, some non-industry factors who yearn for the old days of "roller-coaster" copper prices.

Jan 1, 1964

By David K. Sitler

Continuing advances in manufactured diamond materials used in rock cutting tools have created a new generation of high production tools for mining. This paper will review the three major manufactured diamond products available for the mining industry as supplied by General Electric Company, Specialty Materials Department, and examine the ways in which these materials are employed. As an integral part of this examination, the economic impact of manufactured diamond tools will be evaluated. Time and again, one will find that the premium price of these tools is economically justified when compared to traditional tools.

Jan 1, 1985

By W. W. Mason

The United States began exporting coal in the late 1800'5, at first in very small quantities to Canada and beginning in 1897 and 1896, to the east coast of South America. Shipments to European countries began on a very limited basis in 1902 and these shipments increased gradually until World War One when shipments overseas increased from the 8 million tons per year level to 22 million tons. After the war exports dropped as fast as they had increased and, with the exception of exports to Canada, remained at very low levels until just after World War 11 when the United States again emerged as a major coal exporter. World War II left the coal industries of Europe in ruin. As the United States was the only country able to supply the large quantities of coal at reasonable prices needed for reconstruction of the European economy, the U. S. coal exports overseas expanded rapidly to 42.5 million tons in 1947. Additionally, we shipped 25 -2 million tons of coal to Canada In that year for a total export of 68.7 million tons. Unfortunately, that level was not reached again until 1957 when exports reached an all-time high of 76 .4 million tons- -a high I might add that has not been reached since.

Jan 1, 1980

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By John M. Smith

Kaolin is an important industrial mineral because of its unique properties and low cost. Strictly defined, kaolin is the name given to a group of hydrous aluminum silicates of which kaolinite is the most common mineral (1). Through common usage the mineral, kaolinite, is called "kaolin" or "china clay". In 1972 over 4, 000, 000 tons of kaolin will be beneficiated and shipped by domestic producers. By far the largest user of kaolin is the paper industry which utilizes approximately 65 to 70 per cent of the total production. Kaolin is used in paper as a filler in the interstices of the sheet and as a coating to impart smoothness, gloss, brightness, and printability to the paper. The rubber industry is also a large user of kaolin where it is used as a filler because it adds strength, abrasion resistance, and rigidity to both natural and synthetic rubber goods. Kaolin is used as an extender in paints because it is chemically inert, has a high covering power, gives desirable flow properties, and is low in cost. In ceramics, kaolin is used in whitewares, tile, insulators, refractories, and in some face brick where a white color is desired. Kaolin is also used extensively in plastics as a filler in thermosetting and thermoplastic mixes to give smoother surfaces, a more attractive finish, good dimensional stability, and resistance to chemical attack. Many other process industries use kaolin as a filler, suspending medium, or for color improvement.

Jan 1, 1972

By Neall. George M.

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U.S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. 1 Gambrell and Haynes (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 450? However, to date, no systematic attempt has been made to establish design criteria. In this report, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1977

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By S. C. Nordeng

The program described in this paper is primarily a test of the possible utility of multiple regression in ore search, It was carried out as a cooperative project between White Pine Copper Company, the Institute of Mineral Research and the Department of Geological Engineering of the Michigan College of Mining and Technology. The authors wish to thank Dr. Cleaves Byers, Associate Professor of Mathematics, MCM&T, and Mr. Robert DeBaubien, Graduate Student in Mathematics, MCM&T, for their work in programming the project for the computer,

Jan 1, 1964

By Z. J. Hladysz

The Hladysz Rock Tester was developed at the South Dakota School of Mines as a portable rock strength tester. The hand held device is placed against a rock surface and struck by a hammer. The impacted force causes a steel ball in the device nose piece to indent the rock and simultaneously indent a standard steel bar also contained in the nose piece. By comparing the two indented diameters the compressive strength of the rock can be calculated using laboratory determined correlation coefficients.

Jan 1, 1984

By George Saratsis, George Exadaktylos

In the marbel industry, ore reserves refer to the produced tonnage of orthogonal prismatic, defect-free blocks of commercial sizes and of marketable aesthetical quality. On the contrary, in the mining sector, ore reserves refer to the tonnage of ore with grade above some cut-off value. While in the mining sector ore reserves are reported according to existing standard guidelines, the marble industry has no standardmethod. The purpose of this paper is to present a method to estimate white marble reserves using drill coring or borehole wall logging and limited joint mapping on exposed marble surfaces. Data pertaining to fracture orientation, fracture frequency, size, and whiteness were collected. The primary phase of marble characterization is followed by the discretization of the orebody into a three-dimensional array of orthogonal prismatic blocks, where the marble whiteness and fracture intensity are attribute values. Both these variables are considered to obey continuous and not discrete probability distributions. The discretization is performed using computer aided design and the Block Kriging techniques. An outline to improve the description of a given marble ore deposit at the exploration stage is presented for the prediction of marble block size distribution from joint count measurements along diamond drill cores. An example case of a white dolomitic marble quarry is used to demonstrate these methods.

May 27, 2020

By Alvin D. Cronberg

Silica flotation with amine salts has been a commercial process for years in certain non-sulfide mineral systems. Phosphate rock and feldspar deposits are notable examples. Generally, the quartz is clean and coarse. Primary amines and imidazolines are used, usually in a mole weight range 250-300, ad often fairly impure grades of collectors are satisfactory. As the production of magnetic iron concentrates grew in Michigan, Minnesota, Canada and in foreign locations, the iron mining companies began to explore amine flotation of silica to improve these concentrates. Many of the mining companies, as well as reagent suppliers, government laboratories and university research teams, had already studied amine collectors for silica, but the application to magnetic iron concentrates presented a real commercial opportunity to apply the art. Amine flotation of silica has been accomplished by simple addition of a flotation cell, and possibly a regrind mill, at the end of the magnetic concentration process. The flotation system gave the mill operator a flexible method to control final grade caused by ore variations in the feed. It increased iron content with lower silica, which resulted in lower freight costs per unit Fe and better pellets for blast furnace use.

Jan 1, 1968

By Stanislatv Pawlowski

New, large sulphur deposits were discovered in Poland in 1953, the result of investigations by the National Geological Institute. All deposits occur in a widespread Miocene evaporite unit in the Carpathian foredeep. The gypsum underlying impermeable Sarmatian clays was altered to limestone and native sulphur where penetrated by hydrocarbons and bacteria. All deposits occur in Miocene structural uplifts. The early determination of the genesis of the sulphur deposits and their occurrence in elevated blocks led to an exploration program that successfully located new deposits.

Jan 1, 1978

By J. E. Bevan

Once mining compromises the stability of a rock mass, the dangerous task of roof bolting begins. Many attempts have been made to automate this process, but there are still many refinements that need to be made. In the past, roof bolting modules were designed around the abilities of a human operator. Currently, researchers are taking a new approach that focuses on designing modules that can utilize bolting methods that are easily automated. A non-rotating anchor that is locked into position by a linear force (as opposed to a rotational force) was designed by researchers at the U.S. Bureau of Mines. Once the bolt is secured in the bolt-hole by the anchor, the bolt is tensioned and a collet is used to secure the other end of the bolt. This process replaces the traditional bolt-nut fastening method. This program is part of an effort at the U.S. Bureau of Mines to automate the coal mining process.

Jan 1, 1994

By C. G. Tester

Automatic tripper control systems can be reliable and as such are suitable for use in the mining industry. Proper application of fundamental engineering principles provides the means for the reliability. Some of the principles are: (1) Be sure the system designer designs a system that does the job operations people want done; (2) Use sound logic design practices to avoid internal electrical problems; (3) The design must be maintenance oriented; and (4) Use good quality components. I would like to discuss a tripper control installation at Kennecott Copper Corporation, Chino Mines Division, in Hurley, New Mexico, and how these principles apply to this tripper control system. First, however, I will expand on the principles to clarify just what is meant. First, "Be sure the system designer designs a system that does the job operations people want done.? Operator acceptance is often the key to the success or failure of an automatic control system. One of the best ways I know of to get operator acceptance is to give him a system that he wants. I don't mean to imply that if bad practices or procedures exist that they should be incorporated in the control system. I do think that many designers feel they haven't done their job if the control system doesn't do things drastically different than the old manual method. Good engineering principles dictate that the job should be done right and if the manual method was right it can very likely be right for the automatic method.

Jan 1, 1973

By Ray H. Hario

Background of Erie Mining Company Erie Mining Company, managed by Pickands Mather & Co., is one of the largest producers of iron ore pellets in the United States. The plant is located at Hoyt Lakes, Minnesota, sixty-five miles north of Duluth on the eastern end of the Mesabi Range. Taconite Harbor, situated on the north shore of Lake Superior, is the location of its Power Plant and shipping facilities. (Figure 1) Even though the plant commenced operation in September, 1957, its true be-ginning can be traced back to 1931 when Pickands Mather, in conjunction with Bethlehem Steel Corporation and Youngstown Sheet and Tube Company, began investi-gating the possibilities of processing low grade ores. In 1940, Erie Mining , Company was formed. During the early and middle 1940's, laboratory and pilot plant research was proven to a point where a preliminary plant was deemed feasible and built in 1948. This plant had an annual capacity of 203,200 t (200,000 long tons) per year and, until mid-1952, was the only taconite plant in existence using commercial-size equipment. During this period, ownership of Erie Mining Company was expanded to include Interlake, Inc. and The Steel Company of Canada, Limited. In 1953, authorization was obtained from the owners to build a 7.62 M t (7.5 M long tons) per year plant at a cost in excess of $300,000,000.

Jan 1, 1977

By E. R. Drevdahl

It has been suggested that we at the University of Arizona present a paper covering the origin, philosophy, and results of the College of Mines program in the field of computers and operations research. I have worked with the program since its beginning, and I will try to outline the developments as they have taken place. The formal development of the educational and research program in the field of Operations Research and Computer Applications at the College of Mines, University of Arizona, began in early 1957. During the year, the University offered its first formal instruction in computer programming. This was my first introduction to computers, and it did not take long to realize that this new tool had a potential that could be profitably utilized by the mining industry. In March 6f 1957, the University Computing Center began operations with its IBM 650 computer. This machine was the only computer of this size in the local area at this time, The first programming effort was in machine language and the programming cost could only be justified for repetitive-type of problems. The progress in the computer field moved very rapidly and with the development of the many compiler and assembly programs and the addition of sub routines to the computer library, the scope of problems that could profitably be investigated by computers expanded rapidly.

Jan 1, 1963

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995