Search Documents

By Gilbert Sauriol

The mining complex, which the Mines Gaspé division of Noranda Mines Limited has operated in Murdochville since 1954, includes open pit and underground mines, two mills, one leaching plant and a smelter. The under- ground mining uses predominantly a large scale room and pillar method, rooms 15 m wide, 30 m high and 300 m long being common. Ore production is effected by 4.5 m3 front-end loaders and 32-tonne trucks powered respectively by 225 and 325 kW diesels. Daily dust and gas readings show that air quality can be maintained at an acceptable level with much less ventilation than that normally specified. This paper emphasizes the point that air requirements should be based on Air Quality Standards, thus allowing an operation to benefit from favourable conditions or from improvements such as exhaust treatment, fuel alteration, etc.

Jan 1, 1983

By Jinke Li, Fenghua Wang

"While coal fueling China's economic growth it has already been causing severe pollution and amounts of CO2 emission. How to make deep reductions in carbon emission is not only a huge challenge for the greatest consumer of coal, but also a revolution for China’s coal industry. The paper explores how to shrink CO2 emissions during the lifetime of coal. The paper points out that increase of coal mine efficiency and productivity, green mining, utilization of coal mine methane and environment-friendly disposal of coal gangue can reduce CO2 during coal mining; coal preparation and coal by wire can decrease CO2 during coal preparation and transportation; improving combustion efficiency, CO2 capture and storage (CCS) and coal transformation can lessen CO2 during coal utilization. The paper also points out that Circular Economy Park is a practical way to develop a low carbon economy for coal industry. An econometric model for total coal industry and each sector are constructed to measure carbon emissions based on CO2 equivalent emissions, then with detailed calculations, based on potential greenhouse-gas emission's reduction, a most likely low carbon roadmap of China's coal industry is depicted with scenario analysis method.Introduction Global warming poses a profound threat to humanity and the natural world and is one of the most serious challenges humankind has ever faced. According to the 2007 Fourth Assessment Report by the Intergovernmental Panel on Climate Change (IPCC), global surface temperature increased 273.89 ± 273.33K during the 20th century (IPCC 2007). Increasing concentrations of greenhouse gases have caused most of the observed temperature increase since the middle of the 20th century (United States National Academy of Sciences 2008), and CO2 is the most important cause of global warming. In 2005, CO2 contributed 76% of global greenhouse gas emissions, CH4 contributed approximately 16%, N2O contributed approximately 6% and the combined F-gases contributed approximately 2% (IEA 2010). Among the many human activities that produce greenhouse gases, energy use is by far the largest source of emissions. Since 1870, CO2 emissions from fuel combustion have risen exponentially (IEA 2009). Of the three types of fossil fuels - coal, natural gas and petroleum - coal constituted only a quarter of the world total primary energy consumption in 2007. The situation is even more critical in China than in the rest of the world, as energy-intensive industrial production is growing rapidly, and large coal reserves exist in combination with limited reserves of other energy sources. The development and production of the coal industry provide stability in China's economic growth. There are more than 7000 coal enterprises in China; the coal enterprises are the main contributor to China's ""economic miracle""."

Jan 1, 2017

By J. M. Beck

Mineral property appraisers engaged in eminent domain actions on properties for which mining is the highest and best use must be fully competent in all phases of mineral resource estimation, mine project development, and mine operations (or retain the requisite competent assistance), as well as educated in eminent domain appraisal (USPAP Competency Rule). Failure to ensure such triggers the issue of appraisal competence and demonstrates a flagrant disregard of the myriad code(s) and guidelines to which the appraiser is subject. The cavalier assertion of some vague, undefined “latitude” in the valuation process does not exonerate the appraiser from a disregard of the USPAP Competency Rule. Lack of independence (i.e., “advocacy”) in mineral property appraisal is the usual result of a weak background in mining and/or appraisal theory. While it is readily apparent to those able to recognize it in reports and testimony, judges and juries cannot be expected to detect or recognize purposefully misleading (or even fraudulent) valuation concepts or testimony. Purposeful deception by the appraiser can lead to specious over-compensation of the property owner (thus victimizing the taxpayer); or, a failure to provide appropriate and just compensation to the property owner – yet, the purpose of an eminent domain proceeding is to leave the property owner no richer or poorer as a result of the taking. This paper highlights some of the deceptive practices encountered in litigation settings and raises issues of competency, professional ethics, and the effectiveness of the inherent enforcement capabilities within those institutions awarding professional certifications. INTRODUCTION The practice of eminent domain mineral property appraisal requires (particularly with respect to undeveloped mineral properties) that the appraiser possess the requisite level of competence in all phases of mineral resource estimation, mine project evaluation, mine development, and mine operation (through closure). To the extent the appraiser lacks such competence, it is incumbent on the appraiser not only to divulge this lack of expertise but also to seek competent assistance in the performance of the appraisal. This competence or expertise can only be obtained through a combination of appropriate and relevant technical education and direct mining industry experience. There exist a number of professional certification and/or credentialing authorities that speak to such competency. In a similar manner, eminent domain mineral property appraisal (as the term implies) also requires that the appraiser possess the requisite level of competence in the practice of eminent domain appraisal. This competence or expertise can only be obtained through appropriate and relevant education, direct knowledge of appraisal theory, particularly as it relates to the concept of eminent domain, and licensure.

Jan 1, 2019

By L. Yuan, J. H. Rowland

"In 1995 and 2003, the U.S. Mine Safety and Health Administration (MSHA) conducted surveys to determine the number of atmospheric monitoring systems (AMS) that were being used in underground coal mines in the United States. The survey reports gave data for the different AMS manufacturers, the different types of equipment monitored, and the different types of gas sensors and their locations. Since the last survey in 2003, MSHA has changed the regulation requirements for early fire detection along belt haulage entries. As of Dec. 31, 2009, point-type heat sensors are prohibited for use for an early fire detection system. Instead, carbon monoxide (CO) sensors are now required. This report presents results from a new survey and examines how the regulation changes have had an impact on the use of CO sensors in underground coal mines in the United States. The locations and parameters monitored by AMS and CO systems are also discussed.IntroductionThe last survey conducted by the U.S. Mine Safety and Health Administration (MSHA) on atmospheric monitoring systems used in underground coal mines in the United States was in 2003 (Francart, 2005). A total of 146 active mines were surveyed. The survey report states that since 1995 there had been a steady increase in the use of atmospheric monitoring systems in underground coal mines as the technology of carbon monoxide (CO) sensors was improved by manufacturers. Atmospheric monitoring systems had become more reliable, and some CO sensors could be purchased with the capability to discriminate between the CO produced by a fire versus CO produced by diesel equipment. This increase in reliability had reduced the number of false alarms and the response time. The faster response time to a developing fire allowed miners to take the necessary action to put out the fire or exit the mine.At the time of the last MSHA survey, some mines still used point-type heat sensors to detect the presence of a fire on conveyor belts. This detection method works by measuring the temperature of the air around the sensor. As a fire starts to develop, smoke and hot gases are produced from the combustion process, and the air is heated up. Once the air and gases reach a designated temperature detected by the point-type heat sensor, a fire alarm signal is generated. Studies have shown that the response times for detecting the presence of a fire using CO sensors are much shorter than when using point-type heat sensors (Conti and Litton, 1995)."

Jan 2, 2018

By Larry Taylor, Thomas Zdeb, Brian Jacobs, Dennis Jensen

Subway tunnels proposed for the Los Angeles County Metropolitan Transportation Authority (LAMTA) East Side Extension are to be excavated below the groundwater through an area of Los Angeles, California with dissolved hydrogen sulfide concentrations in excess of 200 mg/L. To address unique construction and worker safety issues, bench scale and field pilot test studies were conducted to evaluate various mitigation alternatives including in-situ oxidation by chemical injection, slurry pH adjustment to suppress H2S evolution, and chemical treatment to remove the H2S from the slurry and muck material. The results provided the basis for detailed hydrogen sulfide control specifications for the contractor.

Jan 1, 1999

By J. A. Ehler

Speed and torque control of standard A.C. induction motors can be accomplished using a variety of devices ranging from mechanical, hydraulic, and electrical. Also, the motor can be specified as an A.C. wound rotor or D.C. motor using the associated controls. Normally, any one of these drive types can be adequately used to provide the torque control necessary to accelerate a conveyor belt system. The selection will depend on the economics, experience, and preference of the designer or end user. These drive types will be presented from a functional and performance viewpoint to assist in the understanding of the available technology.

Jan 1, 1998

By Shinichi Konda, Gary Nishimura

"Thousands of years ago large glaciers carved much of the landscape in Puget Sound, depositing abrasive and granular soils including cobbles and boulders along with layers of clay and sand. Tunneling in this geology – common throughout much of the northern and Midwestern U.S. – is challenging and can be unpredictable. The use of pressurized face tunneling, most commonly with EPBs and slurry type machines, has made excavation in this geology more efficient, but difficulties still remain. Through analysis of recent projects in Seattle, Washington, USA, the authors draw conclusions as to the best TBM designs and operational parameters for this variable, abrasive and often difficult ground. Performance data is analyzed with an eye towards advancements that could further improve TBM tunneling in glacially deposited soils. INTRODUCTION Over the past several ice ages, extensive glaciers reaching across much of North America transported large amounts of soil and rock as they moved across the land. The substantial weight of the ice sheets mixed together a wide range of soil types along with a variety of rocks and boulders of all sizes. Many rock formations were reduced to pebbles or particles containing highly abrasive characteristics. Any boulders able to survive were generally comprised of harder materials which were scattered throughout the soil. This highly variable mixture of abrasive soils and high strength boulders can be found in many areas across the Puget Sound and other regions of the country. Wherever they are encountered, they often create a difficult and unpredictable mining environment for both equipment design and operation. Modern TBMs are optimized early in the design process for specific types of geology, and unexpected conditions can require extensive modifications. In addition, several operational parameters need to be adjusted to balance ground characteristics, and advance rates can be significantly affected in mixed and rapidly changing soil conditions. Both EPB and slurry machines can be used successfully in these conditions, provided their respective operating criteria are met. Ideally, an EPB is operated with a relatively thick muck consistency, which accommodates moderate changes in soil permeability and maintains a reliable pressure differential through the screw conveyor. However, this also causes higher wear on rotating components and requires more energy at the cutterhead. Alternatively, slurry machines typically operate best with a more fluid muck consistency that can be easily pumped through the extensive piping system. This tends to reduce the wear on the cutterhead and the power requirements of the cutterhead drive system, but also makes the machine more sensitive to changing soil conditions. Generally, the slurry piping system is also more capable of controlling high face pressures, although the screw conveyor of an EPB can also be designed to accommodate most high-pressure conditions."

Jan 1, 2016

By Ali Keneti, Xavier Ryan, Gerardo Sanchez, Shannon Goff

In this study, FLAC3D modeling was conducted for ground-structure stability assessment for a pilot tunnel passing under a large shaft excavated in the vicinity of existing structures at Karangahape Station for the City Rail Link Project in Auckland, New Zealand. The analysis involved generation of the geometries and construction sequences in Rhinoceros®, modeling the existing ground condition, calibration of the simulated in situ conditions with the observed behavior of the ground, and excavation of the shaft and the pilot tunnel. A comprehensive interpretation of the results was then performed accompanied by comparison of the predicted behavior with the observed response of the ground during construction.

Dec 1, 2022

"Caterpillar has developed the Cat GH800B longwall plow system, designed for mining very low coal seams at high rates. Building on the attributes of the proven GH1600 plow system, the Caterpillar longwall team in Lünen, Germany, worked with the German Ibbenbüren Mine to design and construct a system for mining an anthracite seam averaging only 0.85 m (33.5 in.) thick. The result is the GH800B plow and associated longwall system, which is now operating in the Ibbenbüren Mine - where the seam does not exceed 1 m (39 in.) in height.The Cat GH800 plow, with an installed power of 2 x 400 kW, has been the plow of choice for seam heights from 0.9 to 2 m (35 to 78 in.), regardless of seam inclination or coal hardness. But the lower the coal seam, the more difficult the extraction process. Flexibility, reliability, efficiency and serviceability of the whole system had to be refined for maximum productivity in such a minimal height, but several key modifications led to success.The armored face conveyor (AFC) modifications for the GH800B plow system include PF4 plow line pans with a replaceable top trough and a new plow guide made of a one-piece casting to provide extra strength and durability while being lower in height than the previous welded version. External dogbone connectors between the line pans and a strong and flexible relay bar between the AFC and the roof supports (shields) further adapt the conveyor for very low seam operation. To increase coal throughput, the engineering team widened the conveyor crosssection with extended side plates."

Jan 1, 2014

By J. H. Elledge

Hydraulic Transportation of Phosphate Ore from, a 40,000 Cubic Yard per Day Strip Mine IMC is transporting 1500 yards per hour of phosphate ore in a water slurry a distance of approximately five miles from a strip mine to a flotation beneficiation plant at their Noralyn Operation. in Barrow, Florida. This ore, which consists of approximately 1/4 phosphate, 1/2 silica sand, and 1/4 clay slimes, is being pumped through a 20 inch O. D. pipeline using seven 20 and 18 inch GIW metal pumps direct connected to electric, motors. This paper details some of the problems involved and the specific methods used to accomplish this bulk material handling requirement.

Jan 1, 1966

By M. A. Trevits, G. W. Luxbacher, L. D. Patts

"It is almost a given that post-disaster mine conditions will have compromised the mine ventilation system, resulting in a hazardous atmosphere in portions of the mine, and often complicated travel through debris fields and roof falls. Robotic technologies provide the opportunity to gather valuable information to assist decision making or lessen exposure to dangerous conditions. MSHA's Mine Emergency Operations Division (MEO) has utilized a fully permissible mine robot, the V2, for a number of years, constantly updating the unit as new technologies became available. The National Institute for Occupational Safety and Health, as part of the MINER Act Extramural Contract Program, examined the need for additional robotic units and ultimately funded three different types of prototype technologies: two robots, the Snake Robot and the Gemini-Scout, and a mine rescue robotic assist vehicle known as the ""Mule"". The Snake Robot is designed to be lowered through a borehole and to conduct surveillance (gas monitoring, video and audio) in the immediate vicinity, while the Gemini-Scout, designed to be deployed in the mine opening, serves as a more mobile and agile exploratory tool as compared to the MSHA V2 robot. The Mule was developed in response to needs expressed by mine rescue teams for a versatile remotely operated support vehicle and it will move from prototype to MEO utilization in the near future. This paper describes the development of the robot prototypes and discusses their limitations in the prototype stage, possible enhancements and potential applications, as well as the utilization of the Mule. INTRODUCTION The conditions in a coal mine may be dramatically altered after a mine fire or explosion. For example, the ventilation system may not be functioning correctly as control devices may be compromised or damaged beyond repair. The visibility in the mine opening may be limited due to accumulated smoke and dust. Roof support systems may be damaged or no longer functional. Equipment and materials may be strewn about the mine opening. Debris fields, blocked openings, roof falls, flooded areas, gas accumulations and active burning make it very difficult or impossible for those managing the post-event emergency to permit mine rescue teams to enter the mine to conduct search and rescue operations. With the evolution of robots and robotic assist technology there has been a proliferation of purpose-built units for the military, police and law enforcement agencies, urban search and rescue and those contending with hazardous environmental conditions. In each case, the technology used is designed to limit human exposure to the unsafe conditions or to provide access to areas under difficult conditions. For example, a specially-designed marine robot has been deployed into the damaged core of the Japan’s Fukushima Daiichi Nuclear Power Plant to assess the conditions of the containment vessels, where melted fuel is believed to have accumulated. Human access to the area is prohibited due to dangerously elevated levels of radioactivity [1]. Multiple robots were deployed in Amatrice, Italy, to assist in the response after the 6.2-magnitude earthquake devastated the town. The robots were used to explore two medieval churches that were severely damaged and deemed too dangerous for human entry [2]. Tactical robots are regularly used by police and law enforcement agencies when the conditions of the emergency place intervening officers directly in harm's way [3]."

Jan 1, 2018

By Lena Paar

"Underground construction poses certain challenges for all parties involved because the actual ground conditions are often unpredictable. Highly complex projects like tunnel construction are affected by various uncertainties. To address this complexity, the construction contract has to be flexible enough to be adapted to the actual conditions (e.g. divergent ground conditions, work delays). However, the adaptation of a tunnel construction contract does not guarantee the absence of a margin of interpretation. The perfect construction contract is an illusion because ex ante statements of the actual ground conditions are not feasible. This paper will discuss contractual parameters that must be considered in order to enable an effective adaptation of the contract during excavation. It is therefore necessary to discuss the following topics: decision-making competence, variable remuneration, fair-risk allocation, value engineering and partnering between client and contractor. INTRODUCTION Thinking of tunnel construction processes, engineers’ first (or at least second) association is about ground conditions. When constructing under the surface, the project is directly related to the ground conditions; however, ground conditions are known fairly well in advance. The estimated conditions can be the same or can also differ from the existing ones. A clear view of the conditions is possible only by driving through the section. What Hoek calls “Geological unpredictability which is guaranteed to provide some surprises in even the simplest tunnelling job” is, in addition to contractual issues, one of two critical aspects of modern tunneling (Hoek 1982). Almost no research tries to figure out, what flexibility in this context means and how to approach it in the contracts. Papers dealing with the New Austrian Tunnel Method (NATM) pose some principles to meet the requests for flexibility (cf. Austrian Society for Geomechanics 2011). However, it remains unclear how to create contracts in order to make them “flexible” enough to react to divergent ground conditions."

Jan 1, 2016

By Steve Kral

One of the world’s most successful mining shovel manufacturers believes its name is not very well known in North America, particularly in the United States. And there are plans under way to improve on that. Never mind that it is one of the largest mining shovel manufacturers in the world. Or that the mining division has 800 machines in operation worldwide, 100 of them in the United States. And the company currently holds 30% of market share worldwide and 10% in the United States. Forget about the fact that it has already sold more machines world-wide this year than it did during 1995. None of that is good enough. O&K Mining GmbH Dortmund is the mining division of Germany’s giant O&K Orenstein and Koppel. It is one of three divisions of O&K Orenstein and Koppel AG, a US$1.2-billion company. The other two divisions are construction equipment and escalators. The mining division, though, is one of the company’s most successful.

Jan 1, 1996

By V. Nasri, S. Rashidi

The Baltimore Red Line Project is a proposed 22.7-km (14.1-mile) long east-west light rail transit (LRT) line envisioned to connect the areas of Woodlawn, Edmondson Village, West Baltimore, downtown Baltimore, Inner Harbor East, Fells Point, Canton and the Johns Hopkins Bayview Medical Center Campus. The Red Line LRT System has two tunnel segments - the Cooks Lane Tunnel (CLT) and the Downtown Tunnel (DTT). The CLT segment is roughly 1,920-m (6,300-ft) long. It commences at the west portal located at the highway ramp for I 70 (to be removed) and terminates at the east portal that is at the intersection of Edmondson Avenue (U.S. Route 40) and Glen Allen Drive. This segment of the project consists of the following construction components: approximately 1,458 m (4,786 ft) of tunnels, 143 m (469 ft) of cut-and-cover tunnel, and 318 m (1,045 ft) of retained cut (U) section. The approximate horizontal alignment for the Red Line LRT Project is shown in Fig. 1.

Jan 1, 2014

The authors provide a discussion of the paper, ?Coal workers? pneumoconiosis prevalence disparity between australia and the united States,? a peer-reviewed paper that appeared in the technical papers section of the July 2012 issue of Mining Engineering magazine. The original authors, G.J. Joy (gjoy@cdc.gov), J.F. Colinet (jcolinet@cdc.gov) and D.D. Landen (dlanden@cdc.gov), respond.

Jan 1, 2013

By Pablo Hadzeriga

There are two places in the world where potash, trade name for potassium chloride, is economically recovered from naturally occuring brines by solar evaporation. One is at the Dead Sea and the other at Wendover, Utah. American Potash and Chemical at Trona, California recovers potash from natural brines, but uses fuel to accomplish evaporation. Under proper meteorological conditions the use of solar evaporation might be desirable from the economical standpoint. Of course, this may not be true when, if by artificial evaporation, a group of very valuable salts are recovered. This is the case of the American Potash operation at Trona. Solar evaporation has its limits. The working temperature is low. We may say, just to cover most areas of the world where solar evaporation may be practical, that it will take place between 18°C and perhaps around 45°C. In most cases the average working temperature expected will be around 25°C.

Jan 1, 1963

By Georgene Renner, Chee Theng, William Gleason

"A walk through the exhibit hall or a glance at the technical programing that was offered at the 2019 SME Annual Conference & Expo and CMA 121st National Western Mining Conference in Denver, CO, Feb. 24-27 makes it evident that the mining industry is an innovative one that is on the cutting edge of technology. However, a glance at the nearly 6,700 attendees of the conference and it is also evident that while the industry is moving forward at a rapid pace in some areas, it is lagging behind in terms of diversity, both in gender and ethnicity.At Monday morning’s keynote session, Hannah Ubi, a millennial and a public speaker who joked that she is the proud owner of a sixth-place swimming trophy and a number of participation medals, addressed a full house that consisted of many men with gray hair or balding heads. The issue of an aging workforce that is rapidly being depleted by retirements is not a new one for the mining industry. In fact, it has been a concern for the industry for more than a decade. The central question has long been, “when the current senior-level people begin to retire, how do we replace them, and how do we fill the knowledge gap that is walking off into the sunset?” SME has been on the front lines in searching for solutions to the impending problem and, along with industry partners, has worked hard to develop programs that will address these issues. Among other efforts, the Society has developed a Ph.D. fellowship program to encourage people to remain in academia to teach the next generation and to help train the next generation to take over in the private sector.“The SME Foundation’s Ph.D. and Career Development Grant program is exceeding expectations at this point with two Ph.D. students graduating and taking a position in academia and two professors achieving tenure,” SME Executive Director Dave Kanagy said during the conference.The Society’s Minerals Education Coalition (MEC) has done its part to help educate future generations about the mining industry with initiatives like EngineerGirl, the Boy Scout Merit Badge and Move Mining, the Shark-Tank-style competition that was held on Monday with five finalists competing for the top prize (ME, April 2019, page 53)."

May 1, 2019

By R. Hawker, P. Singh, K. V. Jessu, P. C. Pinazzi, A. J. S. (Sam) Spearing

Rock bolts are highly important underground to prevent falls of ground and thus, ensure safety. In situ, the ground reinforcement is subjected to a combination of loads, such as shear, tensile, and/or bending loads. Studies have been conducted to evaluate the effect of either shear, tensile, or bending loads on the ground support. However, only a few studies have been done to evaluate the effect of combined load on the rock bolt performance. In situ, the order of loads acting on the bar cannot be predicted, and more than one load can act on the bar at the same time. Thus, a hybrid failure criterion was developed that covered all combined loading conditions. Fifty-eight un-grouted laboratory rock bolt tests were conducted in total under two load conditions: applying shear displacement to the rock bolt and then tensile load to failure, and applying tensile displacement to the rock bolt and then shear load to failure. From the test results, the failure criterion was developed based on regression analysis. A nonlinear relationship was determined for the loading condition variations. The failure criterion presented in this paper can be used as a guide in the rock bolt capacity design under all loading conditions.

Sep 8, 2020

By Rolf N. Schulz

The recently completed major modifications and additions to Reserve Mining Company's taconite concentrating process incorporate a totally new control system. Design of the new control scheme is centered on reliability, versatility, centralization, and optimization. The design objectives were achieved through a distributed control system based on a network of independent field located micro-processor based control systems connected to a central control room. Operation of each micro-processor can be interrogated and modified from the central control room by the operator or by either of two computer systems. The two computer systems handle logging, alarming, specialized sequenced controls, and complex process optimization routines.

Jan 1, 1980

By J. Sidhom, W. Fourie

"As the mining industry continues to face difficult challenges the need to persistently focus on productivity and utilization of labor and equipment costs will intensify. With these challenges in mind, Komatsu is helping to bring mining performance and analytics to the next level.By evaluating underground haulage, a significant component of the room and pillar mining value stream, variables have been identified and sensitivities have been performed to show opportunities to balance and streamline throughput. As a result of applying operational excellence tools to the mining environment, Komatsu is seeking to optimize mining performances by limiting waste, simplifying the process, increasing productivity and machine utilization, as well as removing workers from harm’s way.These days it’s not enough to work harder; mines have to work smarter. Improving efficiency, reducing costs, increasing safety: these are no longer nice to haves, they are must haves.Starting with the best products and the right people is a first step, but then what? How do mines take their operations from average to being a top performer? By using operational excellence principles aimed at eliminating waste, simplifying processes, automating where possible and removing people from harm’s way.The fundamentals of operational excellence (OpEx) are based upon the process of define, measure, analyze, improve and control (DMAIC). DMAIC is an improvement cycle that helps with, for example, haulage optimization by: defining the issues and problems in the process as well as the areas of improvement; measuring and collecting mining operational data by time study and equipment monitoring system; analyzing through sensitivities and production modelling to determine root causes and then improving the performance and controlling the operation.Komatsu uses OpEx or lean principles inside its organization to drive efficiency, but it also helps its customers employ them to achieve new levels of productivity and safety.These same principles can be applied in most situations to streamline processes, improve operations and deliver value."

Jan 12, 2017