Search Documents

By John W. Sweeney

Florida is usually thought of as a vacation State, not a mining State, yet Florida has been the leading producer of phosphate rock in the United States for 85 consecutive years and in 1978 supplied over 80 percent of the national output and over 30 percent of the world's output. It is estimated that the Central and South Florida phosphates contain 412,800 short tons (374,000 metric tons) of U308, that 115,000 short tons (104,000 metric tons) of U308 will be contained in the wet-process phosphoric" acid procsssed in the United States through the year 2000, and that 54,000 short tons (49,000 metric tons) of U308 will be available from Florida. In 1978, two companies in Florida and one in Louisiana went on-stream recovering uranium oxide from wet-process phosphoric acid and three others started construction of U308 extraction facilities. These six companies will have the capacity to recover 2,137 short tons (1,900 metric tons) of U308 annually in 1980, which will account for about 15 percent of our domestic requirements.

Jan 1, 1979

By Elimame Elaloui, Kais Elghniji, Constantin Virlan, Aurel Pui, Chaima Ouled Amor

Separation and identification of minerals composing the Tunisian silica sands have been conducted by acid etching and hot filtration/sedimentation (HFS) without affecting the quartz component. It was found that the hot acid etching process is an effective method to separate quartz and clay minerals in the silica sand. The SEM micrographs of the silica sand show rough surface and some cracks with irregular shapes. The surface becomes clean and smooth after acid etching process. After chemical dissolution, the clay minerals were recovered by hot filtration following by sedimentation at low temperature. FT-IR, EDS maps, and secondary electron (SE) analyses of separated clay minerals reveal the presence of Fe2O3, montmorillonite, and kaolinite minerals. The LIBS analysis of clay minerals shows the presence of Al, Fe, Ca, Al, and Mg. The sequential etching process can be introduced in the purification methods as an effective way to separate quartz from clay minerals.

Jul 29, 2020

By C. J. Slaughter, S. P. Harteis, L. L. Chasko, D. W. Alexander

The Department of Health and Human Services (HHS), National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), with the assistance of cooperating underground mining operations and state agencies, has conducted research exploring devices and technologies that could be used to assist miners navigating through smoke and dust resulting from a fire or explosion. Recent events in mines confirm that smoke and dust can enter and contaminate mine escapeways, creating an atmosphere with severely reduced visibility. This reduced visibility results in substantially increased escape times, possible disorientation or confusion, and increased stress levels, and may prevent evacuation altogether. Tools or devices that assist miners in navigating through smoke-filled areas void of lifelines could make the difference in successful escape from the mine. This paper presents the results of OMSHR research to identify and evaluate tools and devices that could provide meaningful information to evacuating miners in areas with limited visibility and without the benefit of a lifeline.

Jan 1, 2011

By R. Klimpel

Recent work has shown that the measurement of flotation kinetics in the laboratory is useful in providing guidelines on how operating sulfide flotation plant performance can be improved. This work outlines the influence of various factors on flotation kinetics such as collector/frother type and concentration, particle size, and frother blending.

Jan 1, 1981

By Kevin A. Foo, Murray D. Bath, John H. Canterford, Arnaldo Ismay

There is no doubt that the dominant future source of gold will be the so-called refractory ores, especially those with gold in a pyrite/arsenopyrite matrix. Minproc Engineers is taking an active role in establishing detailed design criteria for a number of apparently competing processes. This involves generating a detailed understanding of the metallurgy involved, systematic pilot plant testing, and the application of advanced engineering technologies. This presentation outlines the approach adopted by Minproc as well as the design criteria for several current projects.

Jan 1, 1989

By A. K. Raina

Blast induced damage to the final wall of rockmass in any civil or engineering application is a major concern to the rock excavation engineers. There are at least four distinct techniques practised by blasting engineers to minimise the damage to the parent rock during blasting that are classified as contour blasting. One of the methods to achieve a smooth wall or rock surface in blasting is pre-splitting, where blastholes in the final row are mildly loaded with explosives and fired first in sequence before the rest of the holes in a round of blast to achieve a split in rockmass. Since blasting is one of the most adopted methods for achieving a final wall in a desired shape, while maintaining the rockmass integrity, the design of pre-split blast assumes importance. There are several variables that determine the final shape of the pre-split face including the rock type, the drill diameter, the explosive characteristics, the orientation of major joints with respect to drill hole, the linear charge density, the spacing of drill holes and inclination of the drill holes. This study attempts to determine the importance and sensitivity of variables in pre-split blasting using historical data from open excavations of a hydroelectric project in India. Keeping in view the multitude of variables, low correlation of independent variables with responses and high level of interactions between the variables that define the blast results, it was found suitable to use ANN to determine the importance and sensitivity of the variables involved. A new method to determine the blast induced damage to rockmass, namely, undamaged area (AUD%), is introduced. Half Cast Factor (HCF%) and AUD%were calculated for a high wall and trenches by digital image analysis technique using the Fragalyst software. Joint spacing and linear charge density emerged as most controlling variables in determining the final result of pre-blast. The relative importance of other variables assuming significance in the case of both the designed outputs is also discussed. A comparative analysis of HCF%and AUD%on the basis of results obtained from ANN analysis is also presented. A futuristic approach concept has also been introduced.

May 30, 2021

By W. Burr Bennett

The prestressed concrete industry in particular, and the precast concrete industry to some extent, are rank newcomers to the concrete construction field compared to the cement, ready-mixed or concrete masonry industries. This young industry reflects its youth and vigor in its enthusiasm, optimism and the belief that it can reach any goal it chooses to set -- and it is setting its sights high. The prestressed and precast concrete industry fully expects to become the major structural and architectural material by the 1980's. Before exploring how the industry expects to reach this goal, a brief look at the origins and the growth of the industry may be useful in an evaluation of the feasibility of this goal. It was always recognized that concrete, strong and efficient for supporting loads which cause compression, was weak and inefficient when used to carry loads which induce tension. Thus the reason for reinforced concrete in which the concrete efficiently carries the compression in a flexural member while low grade steel bars reinforce the concrete in the areas 'of tensile stress. (Fig. 1). The steel being relatively inexpensive, can passively, but quite effectively carry tensile force while the concrete carries compression. The concrete in contact with the reinforcing also protects the steel from corrosion and acts as insulation to provide a superior "built-in" fire resistance. The major disadvantage of reinforced concrete relative to its main competitor, steel, is its weight in relation to its load-carrying capacity. Reinforced concrete systems, such as waffle slabs, I-beams, thin shells, etc. ,

Jan 1, 1971

Silver bearing bulk sulfide concentrates from several Peruvian mines were autoclaved in a 19 liter (five gallon) laboratory autoclave in Lima, Peru. Cyanidation of autoclaved concentrates following a hot lime jarosite destruction step extracted over 98 percent of the silver and over 95 percent of the gold. Autoclave operating parameters such as time, temperature, pulp density and autoclaved solids recycle were investigated and reaction rates determined. The problems of excessive heat generation, silver solubility during autoclaving, and formation of pellets containing unreacted sulfides were addressed. The data presented will be used to design a continuous autoclave pilot plant to pro-vide reliable scale up data for a 50 -100 ton per day facility.

Jan 1, 1992

By A. N. Pritchard

The development of vibrating screens over the last century has seen many variations to suit the exacting requirements of industry. Indeed, as each year passes, industry has presented the challenge to screen manufacturers of supplying larger machines than those used in the past and the question is often posed - what is the maximum limit? Not only must size or screen area be considered but excellence of performance in terms of screening efficiency must be maintained or maximized.

Jan 1, 1983

By S. Al-Thyabat

In this work, the floatability of Jordanian phosphate slime (-38 µm) was evaluated in a batch column flotation cell, 100 cm high and 5 cm inner diameter. Flotation was conducted using sodium oleate as a collector and methyl isobutyl carbinol (MIBC) as frother. Rougher flotation yielded concentrate assaying 29.19% P2O5 with 90.29% recovery at the following flotation parameters: 2.6 cm/s superficial gas velocity, 20 ppm frother dosage, 0.205 mM collector concentration and 40% weight solids. It was also found that conditioning with the same collector dosage but with a different solids weight percent gave different flotation results. However, pulp collector concentration was the key operating parameter; increasing collector dosage at the same solids weight percent decreased flotation recovery by 3%, while increasing solids weight percent at the same collector dosage increased phosphate recovery by 18%.

Jan 1, 2011

By R. P. Killmeyer, W. W. Wen, B. K. Parekh

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen-bowl centrifuge for the dewatering and reconstitution of column -flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine clean-coal slurry from the column flotation con¬centrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free flowing granularform, while the untreated products were wet, sticky and difficult to handle. Test results indicated that the average moisture contents of the dewatered coal products were 35.7%, 35.5%, 32.6%, 29.9% and 26.5% (by weight) with Orimulsion additions of 0.0%, 0.7%, 3.2%, 4.8% and 6.4% (by weight), respectively. The handleability and dust reduction of the dewatered coal products were also vastly improved.

Jan 1, 2000

By I. Moreno-Ventas, G. Ríos, J. C. Fernández-Caliani, M. Bacedoni

"This paper delves into the constraints on the nature, origin and thermal evolution of the accretions formed in the uptake shaft of the flash smelting furnace operated by Atlantic Copper in Huelva, Spain, outlining recommended practices for preventing accretion buildup. The accretions were investigated using quantitative electron probe microanalysis, X-ray diffraction and digital imaging techniques, and the experimental data on mineral composition, crystal chemistry and textural relationships were interpreted in terms of thermodynamic phase equilibrium in the SiO2-Fe-O-S system. The results suggest that two distinct types of accretions were formed by the fractional crystallization of two coexisting immiscible melts, under changing conditions of oxygen partial pressure (pO2). The type I accretion of magnetite + delafossite ± cuprite ± tridymite ± metallic copper crystallized from a fractionating copper-rich melt at pO2 above about 10-5 atm, while the type II accretion of magnetite + fayalite + metallic copper + chalcocite derived from a melt with lower copper concentration when pO2 levels dropped below that critical level. Phase compositions and textures were consistent with a cooling history of both compositionally contrasting liquids from about 1,250 °C, the liquidus temperature of magnetite, to eutectic or near-eutectic temperatures of around 1,100 °C. The maintenance of appropriate temperatures — above the liquidus temperature of magnetite — and oxygen partial pressure levels may be critical for the prevention of accretion buildup. IntroductionCopper flash smelting with oxygen-enriched air, an autothermal process developed half a century ago by Outotec (Espoo, Finland), formerly Outokumpu, currently accounts for about 50 percent of the world’s primary sulfide-based copper (Schlesinger et al., 2011). The partial reaction of copper sulfide concentrates produces two separate molten streams, copper-iron-sulfide matte and iron oxide-rich slag, and releases sulfur dioxide (SO2) gas. The matte is sent to converters to remove the remaining iron and sulfur, leaving blister copper with grade of about 99.5 percent copper (Cu), which is cast into anodes for electrolytic refining.The SO2-rich gas generated by the oxidation of sulfide feed particles contains a significant proportion of dust that is entrained in the process off-gas. The gas from smelting is transferred into a waste heat recovery boiler, where it is cleared of dust and cooled before it is converted into sulfuric acid. If the process is not operated properly, the dust-bearing gas may form accretions between the uptake shaft of the flash smelting furnace and the waste heat recovery boiler, causing severe problems in the gas handling system (Swinbourne, Simak and Yazawa, 2002; Miettinen, 2008; Stefanova et al., 2012). Removing the dust accretions usually requires a greal deal of time, effort and resources. Understanding the buildup of accretion may help in reducing the problems and optimizing the process"

Jan 1, 2017

By Ali Ahmadi, Andreas Rausch, Angela Binder, Stefan von der Mark, Dhananjeyan Jeyaraj, Jana Thomas, Nils Nöther, Stefan Wittek, Thomas Ulrich, Eleni Gerolymatou, Mario Kolling, Helmut Mischo, Michael D. Martin, Tugba Sen, Jens-André Paffenholz, Erik Farys, Oliver Langefeld, Wilfried Ließmann

This paper outlines the MOVIE project, which is dedicated to the development of a digital twin for an underground laboratory at the research and education mine “Forschungs- und Lehrbergwerk Reiche Zeche” in Freiberg (Germany). Data from induced rock deformations and temperature fluctuations is collected using fiber-optic sensors. The objective of the project is to establish a virtual laboratory for real-time analysis of the interactions between geology, geomechanics, geometry and ventilation. This will be achieved by integrating models from these disciplines with artificial intelligence, creating a sophisticated hybrid model. The insights gained will enhance safety and efficiency in mining through improved digital planning options, ultimately contributing to more effective resource management and operational decision-making in different mining environments.

Feb 1, 2025

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage organizations to work together, executing such risk assessments comes with challenges. This paper focuses on one trona mine’s experience in the development and implementation of a field level risk assessment program to help its entire organization understand and manage risk to an acceptable level. Through a transformational process of ongoing support and communication, Solvay Green River fostered a culture of trust and safety grounded in risk assessment, safety interactions, and hazard correction. The application of consistent risk assessment (RA) tools was critical to create a participatory workforce that not only talks about safety, but actively identifies energies that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s process of RA implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks. As discussed, consistent efforts to establish a participatory risk management program are worth the initial struggle to ultimately reduce incidents. INTRODUCTION Work-related health and safety (H&S) incidents often account for lost days on the job, contributing to organizational/financial and personal/social burdens [1-2]. Accompanying research demonstrates that risk and ambiguity around risk contribute to almost every decision that individuals make throughout the day [3-4]. In response, understanding individual attitudes toward risk has been unquestionably linked to predicting H&S behavior [5]. Although an obvious need exists to identify more comprehensive methods to assess and mitigate potential hazards, some argue that risk management is not given adequate attention in occupational H&S [6]. Additionally, research suggests that a current lack of knowledge, skills, and motivation are primary barriers to mitigating workplace risks [3-6]. Therefore, enhancing knowledge and awareness around risk-based decisions, including individuals’ abilities to understand, measure, and assign levels of risk to determine an appropriate response, is increasingly important in hazardous environments to predict and prevent incidents. This paper focuses on tailored approaches to field level risk assessment (FLRA), measurement, and common barriers to participating in such activities. The authors use a trona mine in Green River, Wyoming, as a case study to illustrate how the organization overcame widespread and site-specific challenges to implement a proactive risk management program. By discussing the mine’s tailored FLRA program, this case study contributes to the literature by first, providing examples of critical components that need to be in place to ensure successful risk management and second, context for continuous quality improvement that can foster a higher level of trust and empowerment on site."

Jan 1, 2017

By D. R. Nagaraj

Secondary Ion Mass Spectroscopy (SIMS) was used to study adsorption of sulfide collectors such as modified thionocarbamates and thioureas, xanthate, dithiophosphate, and dithiophosphinate, on galena, chalcocite, chalcopyrite, and quartz under flotation related conditions. In the case of the adsorption of modified thiourea on chalcopyrite, chalcocite and Cu-activated quartz, and of dithiophosphinate on galena, SIMS measurements have provided direct evidence for the presence of metal-collector (1:1) complexes on surfaces. In the other systems, only the collector molecular ion and its fragments were detected. The distribution of adsorbed species on the surfaces was obtained by using SIMS in the imaging mode. On chalcopyrite, only the copper-collector complex was found; there was no evidence for iron-collector complex. In the case of quartz, adsorption of selective collectors was observed only after activation by copper ions.

Jan 1, 1996

By G. Barbery

In Mineral Processing, the objective of most processes is the separation of mixtures of minerals, which are originally associated in composite particles. Feed preparation processes grinding for instance, which take place before beneficiation or separation processes do not usually break particles at the boundary between mineral phases. They produce composite ("middlings") as well as liberated particle. It is therefore necessary, in a particulate system, to determine the proportion of particles which are liberated as well as, ideally, the size distribution of minerals which remain associated in composite particles. Up to now, there has been a lack of experimental techniques to characterize completely composite particulate systems. Heavy liquid separation which is commonly used to obtain information of this type can only be applied to simple binary cases for which one mineral has a low density (lower than e.g 2.8 ). The technique which is proposed in this paper involves the measurement of parameters on polished sections of particles mounted in a matrix, and the use of mathematical transformations to reconstruct in three-dimensions the information obtained from these measurements .

Jan 1, 1977

By Alistair James, James Alcorn, Chaitan S. Sandhu, Andy Small

The Risk-Informed Decision Making (RIDM) working group is a group of industry professionals formed under the joint initiative undertaken by United States Society of Dams (USSD), Tailings Dam Safety Committee and Canadian Dam Associations (CDA) Mining Dam Safety Committee (MDC). The working group was organized to develop a guideline on implementation of a RIDM process relating to the design of mining water dams and Tailings Storage Facilities (TSF). Since its formation in 2022, the group has completed a literature review of more than one hundred (100) cross industry publications on applications of RIDM in mining water dams and TSFs, has held two industry workshops in Niagara Falls, Ontario in 2024 and Saskatoon, Saskatchewan in 2025 to capture industry input relating to the understanding and application of RIDM. The working group has subsequently formulated a process that constitutes good industry practice as it relates to application of RIDM in mining dams and TSFs. The authors, through their engagement and leadership in the working group and facilitating the two industry workshops in 2024 and 2025, are of the opinion that the successful application process of RIDM across Canada and United States (U.S.) is still not clear to many industry practitioners. There is confusion over terminology, good versus poor RIDM, and in some cases reluctance to use the RIDM terminology. This paper addresses critical knowledge gaps identified in the RIDM implementation for mining water dams and TSFs through three years of stakeholder engagement. It provides clarity of the process via a joint position statement and implementation roadmap, resolves terminology confusion, and documents contradicting industry opinions to promote adoption of good RIDM practices in Canada, U.S. and beyond.

Feb 22, 2026

Water and wind erosion of toxic zinc and lead smelter waste is one of the most urgent environmental problems to be solved in the Silesia region of Poland. Over 87 x 106 Mg of various mining wastes were disposed of in uncontrolled piles leading to soil, water, and air pollution in highly populated areas. Welz and Doerschel process Pb/Zn smelter wastes were stabilized in the summer of 1994 by application of heavy loads of CaCO3 (30 Mg/ha), CaO (1.5 -15 Mg/ha), and municipal biosolids (150 -300 Mg/ha), followed by seeding with a mixture of acid-and salt-tolerant grass species selected in a pot experiment. Vegetation was successfully established on 85% of the Welz material demonstration plot area (0.5 ha), even though it was initially high in water-soluble Zn, Pb, and Cd ranging from 0.4 to 1311,0.1 to 5.8, and 0.05 to 55 mg/kg, respectively. Standing biomass averaged 3.3 Mg/ha on the stabilized Welz waste zone by the end of the third growing season (1997). The revegetation of much of the Doerschel material area failed initially because of extremely high salinity (16 dS m-1), high content of water soluble metals (Cd in particular), and heavy compaction. The area was capped (15 cm) with waste lime and retreated with bio-solids (300 Mg/ha) in 1995, and standing biomass averaged 2.9 Mg/ha in the fall of 1997. The observed plant response to bio-solids and lime indicates this approach to be an environmentally beneficial technology as compared to the traditional methods utilizing topsoil covers.

Jan 1, 1999

By Michael L. Ogilvie

The proportion of underground coal production as a percentage of overall Australian production has fallen in the last 10 years, with underground production remaining more or less static at about 53 Mt (58 million st). However, underground coal mining remains a viable industry in Australia, due to use of modern longwall mining systems. In 1993-1994, 26 longwalls were in operation, with total production exceeding 39 Mt/a (43 million stpy). Some of these longwalls achieve productivity levels approaching efficient opencut operations, and in some cases, they exceed them. These high-production longwall mines are not without problems when depth and distances from outcrop increase and the gas content of the seams approaches or exceeds critical limits. When gas content of a coal seam exceeds 6 m3/t (233 cu ft/st), gas flows into the mine may be sufficient to interrupt production from time to time.

Jan 1, 1995

By Angelus S. C. Owili-Eger

Although the foundation of a unified treatment of fluid flow in variably saturated porous media was established more than seventy years ago, no serious attempt was made to develop it until the early 1970's. Ever since, a number of unsaturated-saturated numerical models have been reported in the literature. However, none of these models have treated multidimensional, multiphase flow in deforming media, parts of which may undergo extensive secondary fracturing. A situation such as this is not uncommon in coal mining operations in which the longwall method of extraction is employed. The present model has been structured to handle such physical systems. This paper presents the mathematical formulation, the numerical algorithm, and a further validation and evaluation of the modified model. The model treats a multiphase flow in a three- dimensional regime and handles mining excavations of complex and changing configurations.

Jan 1, 1980