Search Documents

By Bryan A. Bartley

High intensity, autogenous grinding has been developed in the hard rock, quarry industry and is finding wide application in mineral processing. The autogenous vertical shaft impactor is described and action within the machine is illustrated. This machine is compared with the cascade mill, in the three characteristics of impact, inter-particle rubbing and nipping, of which impact is the most important. There is a seven fold increase in impact level over that of the cascade mill. The autogenous impactor has characteristics of crushing and grinding, preferential crushing, abrasion resistance and drying. These are illustrated by examples of industrial applications, where the machine is now used and range from abrasives, such as Carborundum to phosphate rock.

Jan 1, 1998

By A. C. T. Bigg

Heavy media separation is one of a number of ore-concentration techniques for coarse? feed which, when the ore is amenable, offers economic advantages in the mining stage and/or the processing stage. In mining, simpler and cheaper methods may be used if a greater proportion of waste material can be included in the mining blocks that can later be re-moved efficiently at a coarse size. In the mill, pre-concentration can mean considerable savings in capital and operating costs by down-scaling of equipment sizes particularly in the grinding section. Conversely, throughput may be increased using the equipment already in-stalled in the concentrator.

Jan 1, 1988

By Mark Board

INTRODUCTION As the world's supply of near-surface metalliferous ore bodies is depleted, more emphasis must be placed upon mechanized bulk systems of underground mining. In particular, block caving is becoming increasingly important as a method of mining low to moderate grade deposits at depths of somewhat less than 1219 m (4000 ft). 00 ft). The block caving method requires that the ore body be completely undercut, thereby removing its means of support and inducing failure which progresses from the undercut to the ground surface. As the span of the under- cut increases and the weight of the overlying crushed ore body becomes greater, large stresses are induced on slusher and haulage drifts. Stability of these drifts is critical in block caving operations and often proves to be an extremely difficult task (Kendorski, 1976; McWilliams, 1975). Slusher drift maintenance can be costly, often exceeding that of the original support costs. This chapter analyzes the ground support problems of an Arizona block caving mine. The mine presently uses monolithic concrete liners as a support method. Failure of the liners occurs as the undercut approaches, thus initiating a maintenance problem which will continue until the ore body is depleted in that block or panel. To examine this problem, a simple analysis of the stresses induced by the advancing undercut was per- formed. Utilizing a design method developed by Dixon ( 1973, 1974), the calculated stresses were used to deter- mine the minimum thickness required for varying section shapes of unreinforced concrete liners. It is found that the thicknesses required for stable linings are not economic. Recently developed empirical methods of support de- sign are utilized (Barton, 1974; Bieniawski, 1973) and compared to the analytical method. A final discussion of alternative methods of support is given with recommendations for the use of passive or "yielding" support methods. LAKESHORE MINE (GENERAL GEOLOGY) The Lakeshore copper property is located in Pinal County, AZ, approximately 45 km (28 miles) south of Casa Grande. The Lakeshore deposit is a porphyry cop- per similar to others in Arizona. The ore body consists of disseminated chalcopyrite and fracture fillings in quartz monzonite porphyry (QMP), Cretaceous volcanic (KVS), Precambrian diabase, and Mescal limestone. The ore body has been divided into three distinct zones of mineralization which have been termed (South, 1972) the oxide zone, the sulfide zone, and the tactite zone. The oxide zone occurs in the upper portions of the ore body and consists primarily of leached and oxidized quartz monzonite porphyry and Cretaceous sedimentary and volcanic rocks. The sulfide zone underlies the oxide zone and includes all quartz monzonite porphyry and Cretaceous rocks which have not been oxidized. The thickness of the sulfide zone is variable and ranges from about 61 to 122 m (200 to 400 ft). The tactite zone occurs in a series of Paleozoic metasediments consisting of tactite, quartzite, diabase, hornfels, and dikes of quartz monzonite porphyry. The tactite zone is highly variable in thickness and underlies the Cretaceous volcanic and sediments throughout the mine. Together, the tactite and sulfide zones are known as the thick or tall sulfides. The greatest support stability problems occur in mining of the tactite zone and are therefore the subject of the remainder of this chapter. MINING METHOD The Lakeshore mine is a block caving mine utilizing a panel caving method. The present mine consists of two

Jan 1, 1982

By V. A. Evans, D. L. Hellier

Introduction Preparing a report on fluorspar economics in the US could have been somewhat complicated at one time. This was because the number of producers, both large and small, derived production from different locations through-out the western US and the southern Illinois and western Kentucky fluorspar districts. Companies, such as Allied Chemical and Williamson Mining, operated in the Jamestown district of Colorado. In Walden and Salida, CO, the Colorado Fluorspar Co. operated mines and mills. In New Mexico, both Du Pont and Allied had mines and mills. In the Illinois-Kentucky district, US Steel, Rosiclare Lead and Fluorspar, Minerva Oil Co., and Marathon Oil all produced spar for the US market. Now all of the companies are out of the fluorspar business and, with the closing of the Seaforth Mineral Co.'s Inverness Mining Co., only Ozark-Mahoning Co. survives as a domestic producer. History Ozark-Mahoning Co., as it now exists, was formed in 1946 by the merger of Ozark Chemical Co. and Mahoning Mining Co. Ozark Chemical Co. was started in the 1920s to produce sulfuric acid for two refineries located in Tulsa, OK. Mahoning Mining was originally formed by the founders of Ozark Chemical Co. and the Youngstown Sheet and Tube Co. to produce fluorspar and associated minerals from properties in the southern Illinois and western Kentucky fluorspar district. In 1937, Mahoning Mining started an exploration program, employing contractor-operated churn drills to look for reserves in Hardin and Pope Counties in southern Illinois. Based on known reserves in the area and the results of the exploration program, work was started in the fall of 1938 to build a selective flotation plant at Rosiclare, IL. The mill was completed and put into operation in August of 1939. The company's first mining efforts were in the Cave-In-Rock district just north of Cave-In-Rock, IL. The deposits in this area were of the Manto or bedded type. They have been the mainstay of the company's operations in the Illinois-Kentucky fluorspar district. In 1950-51, the company expanded its operations by purchasing fluorspar properties from Colorado Fluorspar Co. at Walden, CO. This location was operated from 1952 through 1958 and from 1968 through 1973 when it was closed permanently. In 1974, Ozark-Mahoning Co. was purchased by Pennwalt Corp. Presently, it is a wholly-owned subsidiary of that corporation. As the only major domestic producer of fluorspar in the US today, the company's ability to survive under the flood of imported material is directly related to the four major segments of its operations. These are: exploration, mining productivity, maintenance, and marketing. All are done in-house. Exploration The Southern Illinois fluorspar district is located in the most complexly faulted area of the central US. The formations are sedimentary in nature and range in age from Devonian through Pennsylvanian. The deposits are small, they range in size from a few thousand tons up to 900 kt (1 million st), with the average minable deposit being around 544 kt (600,000 st). The ore occurs in both nearly vertical vein deposits and in Manto or flat lying bedded deposits. Due to the relatively small size of the deposits and the depth at which they occur, a good low-cost exploration program is essential to ensure that new finds of ore are equal to the mining extraction rate. Ozark maintains a leased land position in Pope and Hardin Counties that will fluctuate somewhere between a low of 40 km2 (10,000 acres) up to a high of 129 km2 (32,000 acres), depending on total size of tracts leased. Most all lands are obtained through a standard lease purchase option, with a small minimum royalty per acre during the normal 10-year option period. All leases are standard and without deviation to control land cost. All land leasing is done through Ozark's geological staff, who also

Jan 11, 1986

By T. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, ship-lap, etc. to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1989

By R. Jin

Fine coal flotation using gaseous carbon dioxide has demonstrated the potential for producing superclean coal. The success of this new flotation .procedure is attributed to the coal's high adsorption potential for CO2. To understand the nature of gas-phase CO2 adsorption at the coal surface, in-situ FTIR spectroscopy in a controlled-environment chamber with an ultravacuum sys-tem has been used and the results are discussed in view of other experimental results from differential scanning calorimetry. It has been found that specifically adsorbed CO2 molecules at the coal surface are polarized and have a characteristic doublet at 2336 and 2361 cm-1. Two adsorption states have been proposed to account for the doublet observed from in-situ FTIR spectroscopy measurements. It is believed that the band at 2336 cm-1 originates from the activated site adsorption of CO2 and that the band at 2361 cm-1 arises due to the molecular aggregation of CO2 within the coal pores.

Jan 1, 1988

By V. Anthony Cammarota

MINERALS INFORMATION PROGRAM Mineral data collection by the Federal Government actually began in 1882 with an appropriation by Congress to the U.S. Geological Survey (USGS). Although the Bureau of Mines was instituted in 1910, it was not until 1924 that the collection, interpretation, and dissemination of worldwide information on production, consumption, and availability of minerals became the responsibility of the Bureau. The objective of the Bureau's minerals information program is to maintain and provide reliable, timely, and comprehensive data for analysis of national minerals problems. This program is implemented by a staff of specialists who cover about 100 mineral commodities and the mineral industries of 168 countries. Data are also provided on the minerals industry on the State and county level. The specialists analyze information to identify trends and problems, forecast future U.S. and world supply and demand for the nonfuel minerals, and relate trends and developments to their impact on the domestic minerals industry. Data Sources and Publications The primary sources of data concerning the domestic minerals industry are the companies that produce, use, and trade in these minerals. Approximately 60,000 survey forms are sent to industry, on a monthly, quarterly, semiannual, or annual basis, to obtain the data. Domestic trade data are provided by the Bureau of the Census, U.S. Department of Commerce. Information on mineral developments abroad is developed by Bureau specialists from mineral reports supplied by U.S. embassies worldwide, from primary source documents, from a review of the technical mining literature, and from onsite mine and plant visits in foreign countries. The information is disseminated through a number of Bureau publications: "Mineral Industry Surveys" provide aggregated data on a monthly. quarterly, or semiannual basis to give timely information on the most important mineral commodities. "Mineral Commodity Summaries," published each January, provides preliminary annual data on supply and demand and discusses significant events of the previous year. The final data are published later in the "Minerals Yearbook," which is the definitive historical record for mineral statistics. "Mineral Facts and Problems," an encyclopedic work issued every 5 years, covers industry structure, technology, supply-demand analysis. economic factors, reserves, and forecasts of U.S. and world demand for individual commodities. "Mineral Perspectives" and "Mineral Issues" cover important international mineral developments and significant issues of current U.S. policy as they relate to minerals. Discussions and analyses of mineral trends and developments also appear in other Bureau publications, such as "Minerals and Materials" and "Information Circulars." These publications provide the basis for analysis and policy determinations by the Bureau and by virtually every Federal agency concerned with minerals, defense issues, the national economy, and foreign relations. The data are also used by industry in planning capital investments in mines and processing plants, by financial analysts, by U.S. delegations in their work with international commodity groups, and by a host of other minerals related organizations. Data Bases The data bases used by the specialists for preparing publications or in response to a continuous stream of inquiries include both those that contain individual commodity data from respondents, and those that are summary data bases on production, trade, capacity, employment and a number of other minerals-related items, not all of which are derived from data reported to the Bureau of Mines. The data bases maintained on the mainframes are not accessible by non- Bureau users. A 10-year data base of supply- demand data, published each year as an update of tables that appear for each commodity in Mineral Facts and Problems, is available on a floppy

Jan 1, 1987

By P. D. Chamberlain

Agglomeration for the heap leaching of gold and silver ores is the process of attaching fine ore particles-less than 150 µm (100 mesh)-to coarser particles. The fines are thus immobilized and uniformly distributed throughout the heap. This is needed to make heaps more porous and uniformly permeable to the flow of a leaching solution. This article describes liquids and binders used to form agglomerates. Agglomeration techniques and equipment are also described. These include drum and disk agglomerators, stockpile and belt agglomeration, and the use of vibrating deck and reverse-running conveyors. The need for agglomeration The main reason for agglomerating heap leachable ores is to prevent percolation problems in a heap. This is different than pelletizing iron ore. In the latter case, the purpose is to bond very finely ground material into coarser, strong particles. These particles can then withstand the rigors of transportation and the loading forces in a blast furnace. Most percolation problems in heaps are caused by the segregation of coarse and fine particles during heap construction. This segregation creates areas with significantly lower permeability because fines plug the channels between coarse particles. Consequently, the leach solutions are subject to channeling, following the path of least resistance. They percolate downward through the coarse ore areas and bypass or barely wet areas that contain large amounts of fines. This results in lower extraction, longer leach time, and higher reagent consumption. Permeability problems in heap leaching are compounded because of the vertical migration of fine particles after the heap has been built. These fines eventually accumulate in pockets or layers and impede uniform solution flow. The fines move because they are not attached to a coarser particle. Moreover, the sluicing action of leach solution flowing over the surface of particles may break the bond between fine and coarse particles. Some fines are also created by the decomposition of ores after being wetted. Percolation problems are minimized if the fines can be attached to the coarser particles. Fines are thus uniformly distributed and rendered immobile within the heap. Heinen (1979) conducted comparative tests of nonagglomerated and agglomerated gold and silver ores. He showed that percolation rates through agglomerated material usually are improved by 10 to 100 times. This reduces leach time for economic recovery to less than one-third of that for nonagglomerated material, and total recovery may be increased. Cyanide consumption is also reduced in most cases because of the shortened leach time. Even run of mine (ROM) ore should be agglomerated. This can be achieved with moderate success by passing each truckload of ore under a water spray to bring total moisture of the ore up to about 8% to 10%. The ROM ore will mix when the ore is dumped, when it cascades down the slope of a heap, or when it is pushed up with a dozer. Overall, agglomeration allows low-cost heap leaching technology be applied to gold and silver ores and tailings that could not be economically processed by conventional methods, according to Phariss (1982). How agglomeration works Agglomeration means that the clays and fine particles contained in the ore adhere to the coarser particles. This creates a coating of fines around the coarse particles. When the ore has few fines and the percolation problems are not severe, the addition of a liquid may be all that is necessary to make the few fines adhere to coarser particles. However, when the quantity of fines is substantial, e.g., +10% -75 µm (-200 mesh), a binding agent may be needed. Use of solution only for agglomeration There are many forces that cause agglomeration and one of them is the surface tension of water. Water-saturated particles collide with each other or with

Jan 12, 1986

By Werner Hofmann

INTRODUCTION The attempt to interprete lung cancer incidence caused by inhaled radon decay products in items of radiation dose raises the question of the relevant dose. The various dosimetric approaches published by now are characterized by an increasing complexity in the structure of the models used. Ranging from organ doses to microdosimetric specific energy distributions in the cells at risk, a significant trend from the macroscopic to the microscopic scale can be observed. Since tumors originate preferentially in the basal cells of the lobar and segmental bronchial epithelium, these cells are regarded as the critical target for inhalation carcinogenesis. The evaluation of basal cell doses is, therefore, the main objective of lung dose assessments. Various dosimetric models have been published in the past (Altshuler, Nelson and Kuschner, 1964; Haque and Collinson, 1967; Harley and Pasternack, 1972; Hofmann, Steinhäusler and Pohl, 1979, 1980; Jacobi, 1964; Jacobi and Eisfeld, 1980; James , Greenhalge and Birchall, 1980). Due to incertainties of physical and biological parameters involved and the application of different anatomical and physiological models the claculated doses are varying up to one order of mangitude. Independent of the choice of these dosimetric models applied to the calculation of lung doses, deposition, clearance and resulting dose are affected essentially by the properties of the inhaled aerosol as well as by personal characteristics. Both the properties of the exposed individual as well as of the inhaled environmental atmosphere have to be considered in radiation protection. It is the main objective of this paper to illustrate the influence of both parameter sets on basal cell doses by varying the above parameters. PERSONAL CHARACTERISTICS Though it might be more convenient for radiation protection calculations, the biological "man" cannot be represented by a uniform standard man. In Tab. 1 these personal characteristics which cause the variability of man are listed together with the region of their effectiveness. In the following the influence of these parameters will be discussed with regard to lung dose assessments. Besides these factors the great biological variability of all anatomical and physiological parameters involved as well as pathological alterations due to lung diseases cause additional variations in lung dosimetry. [ ] Age Age can be considered as the most important personal factor influencing the anatomical structure of the lung between birth and about 15 years of life. This period is characterized not only by an enlargement of already existing respiratory units but also by structural changes. Besides these anatomical alterations deposition is strongly dependent also on respiration parameters, such as tidal volume (TV) and respiratory frequency (RF). Whereas RF decreases with progressing age in an exponential manner, TV increases significantly resulting finally in a growth of the respiratory minute volume (RMV). Also mucus clearance in the infant might be more effective than in the adult, though no reliable experimental data are available. Superposing all these age-dependent changes mean basal cell doses are higher for children by about a factor of 2 than for adults living in the same radioactive environment (Hofmann, 1981). In the adult the following alterations of respiration standards with age are reported: total lung capacity diminishes with age, functional residual capacity is unchanged or increases with age and the dead space rises slightly with age (ICRP, 1975). The influence of these lung capacities on deposition, however, can be regarded as insignificant. Due to the ageing process mucus velocities my be considerably smaller in older people. This effect can also be superposed by the simultaneous influence of ciliatoxic effects of cigarette smoke and air pollutants or other bronchial diseases. Since the lower age limit for occupational exposure is about 18 years, age can be disregarded in the uranium mining industry for the determination of radiation doses, though lung cancer induction is significantly dependent on age.

Jan 1, 1981

By J. E. Wennen

Screens serve several important functions in CIL and CIP processes for gold extraction. One important screen application known as interstage screening allows slurry to be continuously transfered through a series of CIL or CIP tanks while retaining activated carbon in the tank. In some cases, this has been accomplished by using airlifts to carry slurry containing activated carbon to an external screen which separates carbon as oversize and returns it to the tank by gravity. The undersize slurry advances to the subsequent tank. More recently this has been accomplished using launder screens and Kambalda type screens. These are essentially static screens that rely on air blasts or mechanical sweepers to clear carbon away from the screen surfaces.

Jan 1, 1998

By Julian Brown, Steve Hicks, Zach Agioutantis, Zachary Wedding

Analysis of Coal Pillar Stability (ACPS) software, released in 2018, integrates numerous empirical pillar design techniques. The ACPS program incorporates methodologies originally available as design tools from the National Institute for Occupational Safety & Health (NIOSH), including Analysis of Longwall Pillar Stability (ALPS), Analysis of Retreat Mining Pillar Stability (ARMPS), Analysis of Multiple Seam Stability (AMSS), and concepts including Coal Mine Roof Rating (CMRR), the Mark-Bieniawski pillar formula, and pressure arch loading. The design methodologies that are the basis of ACPS were developed via analysis of significant amounts of real-world data and have been standards of the United States coal industry for decades. While there are empirical factors built into ACPS, making it ideal for use in U.S. coalfields, the concepts in the program have proven to be applicable in variable mine settings, and the software was developed to allow for user-based, site-specific modifications of key design inputs. Application of ACPS to cases outside the regions for which it was developed must be approached carefully, and continuous development of site-specific data is mandatory. A case study is presented involving the application of ACPS to assess pillar stability and assist future design for an underground lignite mine in Eastern Europe. Assessment of in-mine observations, review of the geology of the lignite mine, and evaluation of specific conditions associated with a failure event resulted in “calibration” of key input factors to ACPS. Scenarios evaluated with ACPS suggest that pillar strength and overburden depth are key factors for the determination of pillar stability and design in future areas.

Jun 25, 2024

By J. D. Miller

Certain bituminous coals of recent geological age are known to contain a significant quantity of natural (fossil or subfossil) resin. Such resinous coals are found in the western U.S., particularly the Wasatch Plateau coal field in Utah. Some of the seams in this field contain approximately 5% resin which has been recovered by gravity and/or flotation processes since 1929. Resin concentrates thus produced are of low quality and are usually refined by solvent extraction and precipitation. The purified resins are of commercial importance, being used in the adhesive, varnish, enamel and ink industries, etc: Recently, an improved flotation technique has been developed which involves ozone conditioning to selectively float resin from such coals. In this flotation process, a concentrate product which contains 95% resin at a recovery of 80% can be obtained in a single stage from coal containing approximately 10% resin, whereas conventional flotation at a similar level of recovery produces a concentrate having a resin content of 30-40%. Economic analysis shows that the ozone flotation process has good potential for use by industry.

Jan 1, 1988

By Franklin J. Stermole

The current financial state of the mineral industry, in general, is bad. Economic prospects for improvements in the near future are uncertain. What will improve mineral investment economics so the mining industry can return to a more normal (in terms of past experience) production level? Basically, mineral commodity prices must rise. They must rise to economically justify reopening closed mines and for management to seriously consider expansion or development of existing and new mines. With the worldwide economy depressed for more than a year now (longer for most segments of the mineral industry), supply/demand relationships for mineral commodities are such that prices are depressed-except for precious metals. In investment analysis of the economic potential of existing or new investments in any industry, product price generally is one of the key parameters having great impact on the economic viability of projects. Petroleum and synfuels industry development contracted last year for the same product price reasons that have brought mineral industry development to a standstill. Much of the new mine development activity now underway or in the serious planning stages around the world involves precious metals ore body development simply because precious metal prices are high enough now or are projected to be high enough in future production years to give overall satisfactory project economics. It will take significant improvement in nonprecious metal mineral commodity prices in 1983 to develop significant new mine investment interest except in very high grade ore body special situations. Mineral Investment Decision Making Before progressing further with the discussion of mineral investment considerations for the coming year, it should be emphasized that mineral investment decision making-like all industry or individual investment decision making does not relate just to economic considerations. Investment decision making should and generally does involve three analyses: • Economic analysis • Financial analysis • Intangible analysis Economic analysis evaluates the relative economic merits of investment situations from a profitability viewpoint based on discounted cash flow analysis of projected investment revenues and costs. Financial analysis, on the other hand, refers to where and how the funds for proposed investments will be obtained. Regardless of the project's economic potential, if you can't finance it, the project will not be done. Intangible analysis considers factors affecting investments but which cannot be quantified easily in economic terms. Typical intangible factors are legal considerations, public opinion, goodwill, environmental and ecological impacts, and regulatory or political considerations, to name a few. New mine development investment decision making in the US has been impacted heavily by intangible considerations in the past decade and will probably continue to be impacted by them in 1983. There is a common tendency in literature and management practice to interchange the terms economic analysis and financial analysis. This often leads to confusion about the rationale for investment decisions. For example, in the past year a majority of companies in all types of industries cut back budgets for new projects. Often this was done not because new project economics were unsatisfactory, but because cash flow from existing operations was reduced compared to previous years due to the recession, and debt service requirements were high from existing loans so new borrowing was undesirable. For financial reasons, in other words, many projects were shelved last year. That included some precious metal mining projects and many petroleum projects. Many other projects were shelved for economic reasons (sometimes combined with financial reasons in the case of marginal economic projects). New mine development for copper, lead, zinc, molybdenum, iron ore, and synthetic fuels are a few examples. Economic Uncertainty and Financial Considerations Mineral project analysis has always involved a lot of uncertainty with respect to determining ore grades, tonnage of producible reserves, operating and capital cost projects, and mineral commodity prices estimates. The wide swings in mineral commodity prices in recent years and the almost impossible task of projecting future prices with any degree of confidence or accuracy concerns mineral project investment decision makers. In developing a new copper or silver mine, it is not today's price of copper or silver that is relevant to economic analysis of the mine, but what the price will be during the producing years. There is no way to avoid projecting the escalation (or de-escalation) effects on revenues and costs. To analyze a project in terms of today's dollar revenues and costs implicitly assumes that escalation will not change today's project costs and revenues; or that, if they do change, the project economics will be unaffected by the changes. This often is not the best or even a realistic assumption. The inherent uncertainty associated with historical mineral price swings is exacerbated in 1983 by the uncertainty of when

Jan 2, 1983

By W. J. Schlitt

Introduction A major uncertainty in assessing the potential for heap-and dump-leach projects is how to determine the extraction-rate curve for the recovery of the mineral values from coarse ore. Such material could either be run-of-mine (ROM) or primary crushed ore. The problem with field testing coarse ore, especially for new projects, is the large scale and extended leach times needed to accurately determine the final extraction-rate curve. At least 5 x 103 to 5 x 104 t of representative ROM ore are typically required for a copper test heap, and much more is often used. Kennecott, for example, recently constructed a 0.9 Mt (1 million st) ROM test heap at the Bingham Canyon Mine in Utah. In such coarse ore operations, the ultimate level of extraction will require a leach cycle that can extend from several months to a few years. Quite often, project development schedules do not provide the luxury of mining such large quantities of material or running such long tests. Instead, test data are usually limited to results from column leach studies on relatively fine ore, often with a top size that does not exceed 25 mm. Maximum leach times are also short, typically less than a year before an initial decision is needed on project viability. Proposed method One approach to estimating the recovery from a coarse ore leach is to assume that the leach solution will have some ultimate penetration distance into the rock. Then, the final level of mineral extraction in this "leached rim" will equal the ultimate level of extraction identified in various testing programs. Obviously, if the radius of a given rock fragment is less than the penetration distance, that fragment will be fully leached at the end of the operation. With larger rock sizes, the percent recovery will fall off as the size increases and the fraction of unpenetrated rock mass increases. Such an approach sounds simple but is likely to be complex when applied to a real project. For example, the penetration distance will be a function of both the rock characteristics and the effective length of the leach cycle. The important rock characteristics include rock porosity, the degree of internal fracturing and the mode of mineral occurrence. With regard to the latter, penetration is likely to be greater if the leachable mineralization occurs on fracture surfaces or in veinlets, as opposed to fine grains uniformly disseminated throughout the rock mass. An estimate of penetration distance may be derived from column or heap tests by noting the depth of solution penetration into the larger rock fragments after three, six and 12 months of leaching. While the penetration rate is ore specific, something on the order of 10 to 20 mm/y may be appropriate for competent, primary copper (chalcopyrite) ore. For gold in tight quartz, the rate may be about the same. Copper oxide ores and gold that is hosted in a more porous rock matrix are likely to have penetration rates that are at least two to three times higher, and an even higher rate should be appropriate for uranium hosted in sandstone. As noted above, the length of the effective leach cycle is likely to be measured in years. On this basis, the ultimate penetration distance (dp) would vary from less than 50 to several 100 mm when a particular ore is leached to exhaustion. Several sets of mathematical manipulations are necessary to convert a rock size distribution and corresponding value of dp into an estimated extraction-rate curve. The first step is to break the ROM size distribution down into intervals and then calculate the radius for the mean rock size in each interval. This is shown in Table 1 for rock sizes up to 1.75 m (about 6 ft) in diameter. The next step is to calculate the volume of unleached core and the fraction of rock that is leached. This is done for the following three values of dp: 25, 100 and 250 mm. Results are shown in Table 2. The third step is to select the ultimate level of recovery that will be achieved in the fraction of material that is effectively leached, i.e., the outer zone that is penetrated by the leach solution. This is clearly a site-specific factor that can only come from metallurgical test results on representative ore

Jan 1, 1998

By Harold Stocker

INTRODUCTION This presentation is concerned with the administrative and technical capability of the Atomic Energy Control Board (AECB) to assure compliance with the individual exposure limit for radon daughters (currently 4 WLM per year). It is not concerned with the epidemiological bases for setting the exposure limit. Moreover, the intent is to show how sophisticated methodologies and advanced technologies, applied to radon daughter concentration measurements in uranium mines, convey the spirit of compliance by providing better estimates than do the historical methods. These better estimates mean that more accurate and more precise estimates of each worker's exposure are determined using these more modern methods and devices. The estimates so derived should provide more convincing evidence to an individual worker that his assigned exposure is a valid indicator of his true exposure. In addition, a perspective on the exposure estimate in relation to the exposure limit is given as further evidence that an exposure limit is not the dividing line between "safe" and "unsafe" exposures. A brief description is given of the compliance aspects of the Atomic Energy Control Regulations and of the limitations of purely statistical non-compliance procedures. Most of the emphasis of the paper will be placed on the uncertainties associated with conventional radon daughter exposure determination and the means being employed (and anticipated) to reduce these uncertainties. NON-COMPLIANCE Under current Atomic Energy Control Regulations (1978), the annual individual exposure limit for radon daughters is given without reference to the possible methods of sampling and calculation of radon daughter exposure and without any reference to possible uncertainties or their magnitudes. This is common in such statutes, the details of sampling, calculation, error analysis, and so on, being left for licence conditions or provided as a specific guideline to the licensee on the matter of compliance with the Regulation. Since the exposure limit is contained in the Regulations, compliance with it is absolute, as with any other law. In Canada, a state of non-compliance with the radon daughter exposure limit exists when an exposure (attributed to an employee) is reported by the licensee to exceed the limit. No uncertainty in the measurements or in the overall determination of exposure is reported nor is any requested. Removal of the worker and the loss of his services are the immediate and direct penalty suffered by the licensee for failure to maintain the exposure at, or below, the limit. A worker may be re-instated to employment for the balance of the reporting period only if the licensee can assure the AECB that further significant exposure to the worker will not ensue. In other jurisdictions, such as the United States, non-compliance is defined on a statistical basis. For example, NIOSH, the National Institute for Occupational Safety and Health presents procedures for calculating the 95% Lower Confidence Limit (LCL) in order to "compare the results of occupational environmental sampling to an occupational health standard and make a decision with a known chance of making an incorrect decision that a state of non-compliance exists" (Leidel and Busch, 1975). (In the nomenclature of this presentation, exposure limit would be used in place of "standard", in the NIOSH sense). Furthermore, it is emphasized in the NIOSH document that such numerical comparisons "are necessary only if the sample mean is greater than the standard". The NIOSH document points out, quite correctly, that the "statistical procedures presented below will not detect and do not allow for analysis of highly inaccurate results, i.e., systematic (non-random) errors or mistakes ... If a systematic error is known to exist in an instrument or analytical procedure then correct the sample mean of the data before analyzing for non-compliance". It is certainly not the purpose of this paper to criticize the sophisticated statistical approach to non-compliance as given in the NIOSH document or in similar approaches used in other jurisdictions. Rather, the purpose is to approach, with some introspection, the question of the determination of exposure by the employer for his employee and especially the employee's understanding of, and confidence in, the accuracy of the exposure determination and its relation to the exposure limit. DETERMINATION OF EXPOSURE Historically, in uranium mines, exposure to radon daughters for an individual miner

Jan 1, 1981

? World industrialization, increased urbanization, and population growth are driving a sustained demand for minerals, metals and coal. Energy demand is expected to increase significantly in the coming decades - placing even more emphasis on supply, security and environmental impact issues. ? Several countries are taking steps to nationalize their own resources thus safeguarding their supplies and reducing exports of natural resources. ? Understanding the future availability of critical minerals requires a global perspective. It is essential to know where deposits are located, their reserves and resources, the technologies necessary for production, and the costs of producing and transporting the products to consumers. ? As mining companies look to maintain or increase their operating capabilities and increase their mineral resource bases, the search for commodities expands beyond developed terrestrial regions of the world, to include marine resources. (Figure 1) Operating challenges in these locations include finding skilled workers, building infrastructure, improving recovery technologies and practicing sustainable development.

Jan 1, 2011

By J. Libaude

The Changement mine in French Guyana has, since 1983, processed gold ore by classical gravity methods. A large part of the gold is in the form of very small, free or enclosed grains. Recovery by gravity methods is thus limited (25-30%) and the present plant produces about 40,000 t annually of auriferous waste assaying about 6 git. The company therefore decided to retreat the waste by heap cyanidation. After laboratory tests which showed the feasibility of the method, a pilot test was set up on site. An experimental 3000 t heap, composed of waste of 0-8 mm grain size, was laid out by bucket loader on an impermeable pad covered by PVC and geotextile cloth. The upper layer of the heap was reworked by mechanical shovel to break up the area that had been compacted by the passage of the loader so as to restore adequate permeability.

Jan 1, 1998

By John E. Auten

The computer program "Spike" is an "expert-rule based system" designed to fulfill two requirements. 1) acquaint unfamiliar personnel with big hole drilling techniques and 2) to stimulate the "old hands" in solving drilling problems. "Spike" will not make anyone a drilling expert The best way to understand a computer program is by example, but first some explanation of an? "expert-rule based system", As the name implies, the program tries to imitate a human expert. Unlike a normal computer program which uses a list of instructions to follow in a set order, a rule-base program has a collection of independent rules without an explicit list of things to do, one after the other. This type of program was mandatory to accommodate the ever changing situations and corrective actions that more accurately duplicate actual drilling operations and the advise of an experienced drilling expert.

Jan 1, 1988

By John J. Gillis

There is an ongoing battle to gain general acceptance of fossil fuel byproducts as safe, economical and useful agro-industrial materials. Despite that, the US ash industry is witnessing a steady growth in the volume of coal burned, along with the production of greatly refined, higher-quality ash particulates. There are two principal reasons for this. Economics have caused an increasing number of US electric utilities to convert from oil-burning to coal-burning. And the Federal government has tightened specifications on fly/bottom ash production quality. Hence, it must be noted that new and more stringent Federal regulations were implemented in 1980. The resultant ash particulates are finer, more compact, and less heavy than in previous years. Additionally, the first shift from oil to coal in the US was initiated in December, 1979 by the New England Power Co. in Massachusetts. Coal is the most widely-distributed fuel in the US. And it is found in 38 states. The wide availability of this fossil fuel and its general cost-efficiency, coupled with the undaunted move of US electric utilities toward nuclear power, are major factors affecting the current statistics on ash generation (65.4 x 106 million tons). Interest in the use of coal in power plants is creating a unique ash disposal and use situation for ash producers as well as the Federal government. There are growing quantities of fly/bottom ash residue. Ash producers must decide how this byproduct can be dealt with effectively and profitably. At the same time, government agencies such as the US Environmental Protection Agency (EPA), are commissioned by Congress to assure that solid, liquid, or gaseous material released into the environment is not harmful or offensive to human health and the environment. Additionally, the Federal government is often responsible for establishing and enforcing guidelines and standards governing the use of recycled materials. Several standards and guidelines governing the properties and use of ash in the US have been established by governmental agencies as well as by the ash industry itself. Of these, some have been developed for ash use by a specific federal agency. Others apply to the entire industry. The following is a brief identification of the major specifications for fossil fuel ash: • US Corps of Engineers - These specifications were first established in 1957. They delineate the physical and chemical requirement for pozzolans used in mass concrete. These specifications applied only to Corps of Engineers' concrete construction projects for locks, dams, and other mass concrete projects until 1977. At that time, a joint effort between the American Society for Testing and Materials and the Federal government produced a modified specification that is now generally applied. The Corps of Engineers' ash, however, retained certain aspects of its specifications for its own use, particularly in the area of handling and shipping fly ash to its own projects. Prior to transporting the fly ash to the corps, all potential sources for the ash must be inspected and approved as a supply source. All silos must be filled, sealed, and tested before the ash is released for shipment. The normal test period for the ash is seven days, although several testings may require up to 28 days. Once the fly ash has been released, it can only be shipped to US Corps of Engineers' projects. All shipments are made with a government inspector present during loading. After a truck or railcar is loaded, the silo is resealed until the next shipment. This procedure requires three silos, and a minimum of 454 t (500 st) each should be considered for each storage unit. All silos are strictly committed to Corps of Engineers' use and are not available for other commercial shipments. • US Bureau of Standards - This Federal agency maintains a standard testing sample of nearly every product used in the US. The accuracy of the fly ash chemical analysis is measured by a regular cement and concrete reference laboratory (CCRL) inspection and based on test results from a standard sample of cement. • US Bureau of Reclamation - This agency pioneered several projects using fly ash and required Federal Standard Certification for pozzolans. • American Society for Testing and Materials (ASTM) - This nongovernmental organization began preparing standards for fly ash sold and used in the cement and concrete industry in 1947, at the urging of ash marketing firms. Current standards define chemical and physical requirements and is entitled, "Fly Ash and Raw or Calcined Natural Pozzolan for Use as a Mineral Admixture in Portland Cement Concrete (C 618-80)." • State Highway Specifications - Led by Alabama, many states are moving toward permitting - and in some cases requiring-the use of fly ash in portland cement concrete and with lime for base stabilization projects for roads and highways. • Federal Aviation Administration (FAA) - The FAA acts in an advisory capacity. It has final approval on design specifications for airport construction projects. The agency has established a set of guidelines permitting the use of fly ash, and has approved several fly-ash-specific designs. The most current FAA fly ash projects

Jan 8, 1984

By J. Edwards

A new, world class dump leach, solvent extraction, electrowinning plant for the recovery of copper comes on line in Chile. CODELCO-Div. Chuquicamata has added a new facility to their operations located in northern Chile. The plant demonstrates many unusual features including: underground collection of leachate, high copper tenors, extensive use of plastics and special corrosion resistant alloys.

Jan 1, 1989