Search Documents

By Ethan Steward, Kyle Perry

The study investigates the effects of high-velocity impacts of common mine materials on a reinforced mine seal rated to 120 psi. It found that materials propelled during an underground explosion could generate enough stress to crack or damage seals, even with little visible damage. This highlights the need for careful evaluation of mine seals after any impact or high-pressure event.

Aug 1, 2023

By R. Pandey, G. Elie, E. Sarver

Respirable crystalline silica (RCS) is generally considered the most hazardous constituent of coal mine dust, and a new federal rule is expected to further limit exposures in U.S. mines. For regulatory purposes, RCS is monitored by collecting filter samples, which are analyzed for quartz (the predominant form of RCS in coal mines). The analysis is done using Fourier transform infrared spectroscopy (FTIR) in a centralized laboratory. To enable more timely results, National Institute for Occupational Safety and Health (NIOSH) mining researchers developed a directon- filter (DOF) FTIR analysis method and free FAST software that can be used in the field. For samples collected under specific conditions, FAST processes the FTIR spectral data to determine quartz mass. While the DOF FTIR method is not approved for regulatory RCS monitoring, it could be useful for engineering purposes, such as to evaluate mining parameters or new dust controls. This field study demonstrates how the method, including FAST, can be applied using low-cost, widely available sampling components. It further demonstrates how quartz percentage can be estimated in the field, by pairing a continuous personal dust monitor with a filter sampler.

Jun 1, 2025

By Thomas R. Kuesel

All engineering designs are based on assumptions regarding the behavior of the structure or facility being designed. These assumptions may be based more or less heavily on theory, but are credible only if verified by observations of field performance. Dr. Peck's "State-of-the-Art" paper has described the semi -empirical process of soft ground tunnel design, emphasizing the importance of records of field performance of actual projects constructed under a variety of conditions. This paper will present the principal results obtained from measurements made during construction of the soft ground tunnels for the San Francisco Bay Area Rapid Transit System. SCOPE The BART System comprises 75 route miles, including 14 miles of soft ground tunnelled subways in San Francisco, Oakland, and Berkeley. All tunnels are single-track sections, approximately 18 feet in diameter. Usually there are two parallel tunnels at the same level, but under Market Street in San Francisco there are four tunnels (two over two), and there is also a three-track section (two over one) in Broadway, Oakland.

Jan 1, 1997

By Robert K. Towner, Francis S. Kendorski

Shotcrete drift linings at the Climax Mine of the Climax Molybdenum Company have undergone four years of extensive evaluations as a replacement for thick poured-in-place concrete linings. Any drift lining at Climax must be able to withstand the rigors of undercut and secondary blasting, weight problems induced by panel caving, and the abrasion of slusher mining. Examined here are the conclusions reached so far on shotcrete drift linings which have not yet completed the approximately six-year cycle from development to ore exhaustion. Properly applied shotcrete is an adequate drift lining for all phases of the Climax panel caving system of mining. Undercut blasting will damage shotcrete unless blasts are correctly timed. Weight problems will destroy shotcrete drift linings as efficiently as it will destroy concrete or steel support systems. Abrasion and secondary blasting results are inconclusive as the shotcrete lined slusher drifts have not entered the ore production stage of the mining cycle. In addition to drift linings, Climax has found shotcrete to be invaluable for lining large underground shops, for temporary support systems, for permanent ventilation bulkheads and for the repair of abraded or weight damage concrete lined slusher and haulage drifts.

Jan 1, 1974

By B. C. Haimson

The Committee on Rapid Excavation of the National Research Council has recognized in its 1968 report the need for "improvement of rock-mechanics techniques for measuring subsurface stress field in deep boreholes and for determining stress distribution in walls of underground excavations". The technique recommended in this paper as being most suitable for both deep hole and tunnel wall stress determination is Hydraulic Fracturing. Using this method stresses are calculated directly from the fluid pressures necessary to initiate and extend a fracture away from a borehole. Stress determination by hydraulic fracturing is rather insensitive to inhomogeneity or anisotropy, is not limited in depth except by the length of the hole, requires simple equipment which is commercially available, and can be carried out by unskilled personnel. The method has been worked out theoretically and extensively tested and verified in the laboratory. A number of field tests in deep holes ranging from 300 to 6300 ft have yielded surprisingly good results. Preliminary underground tests have been very encouraging and most recent measurements in a tunnel complex at the Nevada Test Site yielded stresses that were both consistent and reasonable when compared with the expected directionsand magnitudes. It is recommended that hydraulic fracturing be considered as a method of in-situ stress measurement both in the pre-excavation stage of design and during tunneling.

Jan 1, 1974

By Michelle Pienaar, Musa S. D. Manzi, Thabang Kgarume, Glen T. Nwaila, Raymond J. Durrheim, Abrie Oberholster, Hennie Grobler

The South African Mining, Extraction, Research, Development and Innovation (SAMERDI) strategy was launched in 2019 with the goal of modernizing the mining industry. It comprises three major research initiatives: improvement in the efficiency of extraction and health and safety in current mining operations, development of fully mechanized systems to mine narrow tabular ore bodies in hard rock, and development of extraction systems to break rock without using explosives. The crosscutting Advanced Orebody Knowledge (AOK) program seeks to develop and implement drilling and geophysical technologies that can characterize the rock mass ahead of mining and identify potentially hazardous geological features. This knowledge will be integrated with information derived from seismic monitoring. Mining methods, layouts and rock support systems will be adjusted accordingly to mitigate the risk of rockbursts. Boreholes are routinely drilled ahead of mine workings using diamond-impregnated bits. The drill core is logged to identify lithology and geological structures (especially dykes and faults that may be seismogenic), sample the ore body for grade control, and detect areas that may contain water and/or flammable gas. Methods and technology to improve the efficiency of drilling and maximize the information obtained from the drilling process, borehole core, and the borehole itself are being investigated. A range of geophysical technologies are being developed to map the rock mass from the skin of the excavation to a distance of several tens of meters. Light Detection and Ranging (LiDAR) is used to map the geometry of the excavation, including prominent joint, vein and fracture sets and the presence and performance of rock support elements and systems. Ground Penetrating Radar (GPR) is used to penetrate deeper into the rock mass and image joints, fractures bedding planes that influence the stability of the hanging and side walls. Image processing techniques known as ‘seismic attributes’ are being applied to the radargrams to improve interpretation. Electrical Resistivity Tomography (ERT) and various active and passive seismic techniques (e.g. Tunnel Seismic Profiling (TSP), ambient noise tomography) achieve even greater penetration into the rock mass. Finally, machine learning is used to improve the processing and interpretation of seismic and radar data.

Apr 26, 2022

By R. Balderrama Neder

A study consist in 20 column leach tests was performed for the "EI Arco" Copper ore deposit, located on Baja California, Mexico. The main purpose was to define the basic criteria like recovery and sulfuric acid consumption, for a commercial heap leach system design, to process the oxide Copper (Chrysocola) of the deposit. Leach parameters such as, amount of sulfuric acid in the cure solution, cure technique, particle size of the material, leach solution's flowrate application, leach solution's acid strength and height of the lifts, were evaluated to choose those parameters in which the results were the best ones for that particular design.

Jan 1, 1997

By Kevin Lundberg, Philip Sander, Daniel Weinberger, John Reilly

Since the early days of risk management, developments in technology and guidelines (ITA, ITIG, OGG, UCA) have advanced risk management and probable cost estimating, which are now widely recognized. WSDOT’s CEVP risk-based cost validation process is now established after 20 years. This paper traces these developments, summarizes advanced techniques, and presents examples of US and international projects with results. A particular case of using advanced risk evaluation to allow enhanced-capability TBMs to be considered in a competitive bid process is presented. Further advances, including the use of digital twin risk-based representation of complex projects, are described.

Jun 13, 2023

By D. Nebbia, R. Aliberti, F. Solesin

The launch of a Tunnel Boring Machine (TBM) is one of the most challenging activity parts of the construction of a tunnel. Challenges are coming from limited space available, learning curve, concurrence of other activities and in some cases from the geological conditions. Launching a TBM is an extraordinary and complicated operation requiring a great level of planning. The Earth Pressure Balance (EPB) TBM named “Chris” was successfully launched for the Northeast Boundary Tunnel, the largest component of the Clean Rivers Project in Washington, DC. Due to space and time constraints, the 8-meter diameter TBM was launched from a single 20-meter diameter shaft, with a 30-meter-long tail tunnel by means of umbilical connections. This paper presents the steps followed during the TBM assembly and launching to complete the excavation of the initial drive of the tunnel maintaining high level of efficiency and quality despite the space constraints. Specifically, it focuses on the methods and phases used to extract the excavated material (muck) from the TBM and from the tunnel, to supply consumables, precast rings and backfill grout. The paper presents results in terms of productivity, lesson learned and possible alternatives to be considered in similar conditions.

Jun 13, 2021

By Jr. Bacon

Kaolin clay is one of the yeoman minerals. It sees duty in almost every aspect of our lives: -in and on most paper products (from modern newsprint to National Geographic and packaging board) sometimes as much as 25% (by weight) of the product -40% of the tile (ceramic, rubber, and linoleum) you walk on. -15 % of the tires you ride on, -30% of the fiberglass filaments in circuit boards, bathtubs, boats, doors, and more, -25% of many housepaints, adhesives, grouts, caulks, and putty -30% of sparkplugs, power insulators, dinnerware. and toilets, -50% of most catalysts (both cracking and emission control) -20% of cosmetic powders. -20% of wire insulation, and animal feed to rocket insulation!

Jan 1, 1993

By S. Guo

In this paper, a model for the resin anchor bolt system is developed in which the smooth bar is modeled by using one-dimensional truss elements and the resin annulus is modeled by using axisymmetric elements. These two submodels are combined together and then incorporated into the' existing computer code ROOFBOLT. After this development, all of the components in the resin anchor bolt system including smooth bar, bearing plate and resin annulus can be correctly modeled.

Jan 1, 1995

By D. H. Lynch

This paper is a general description of current Central Florida phosphate mining, beneficiation and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry.

Jan 1, 1978

By Ademar Lopes, Victor Silva, Heitor Silva, Gustavo Usero, Roberto Rolo, Lucas Pereira, Gabriel Moreira, João Lague, Arthur Endlein, Matheus Feitosa

Grade control models are supposed to provide a higher resolution than long-term or interim models. However, available grids from diamond or reverse circulation drilling do not provide that required resolution. In this study, a geostatistical workflow is proposed to integrate available grade data from production blastholes with its operational parameters taken when drilling downhole. The step of geological logging can be replaced by machine learning models for classifying blastholes into lithologies and hardness classes. Next, indicator and ordinary kriging use the classified blastholes and previous data for estimating the model domains and the grades within each one. The workflow is applied in a world class iron ore mine in Brazil.

Jun 25, 2023

By Allan Rocas, Aswathy Sivaram, Daniel Cressman, Tatiana Chiesa

The City of Toronto plans to construct a 1,350 mm consolidation sewer along the East Don Roadway (EDR). The project includes installation of approximately 260 meter of 1,350 mm diameter concrete pressure pipe through microtunneling methods. The sewer alignment crosses underneath a busy 5-lane arterial road and then follows the very narrow East Don Roadway road allowance. This paper discusses the significant challenges overcome to design the Don Roadway sewer using slurry microtunneling methods through mixed face conditions below the groundwater table in a congested road allowance. A curved microtunnel was ultimately required to avoid conflicts with existing utilities, condominium tiebacks and a bridge structure.

Jun 13, 2023

By Dapeng JIANG, Haixiao YANG, Shanxi WU, Jinwang Zhang, Guoliang XU, Yipeng ZHANG

The subsidence and deformation characteristics of strata with thick unconsolidated overlying strata is quite different from that with consolidated overlying strata. In this paper, based on the engineering background of large mining height mining in No.21 coal seam of Zhaogu No.2 Coal Mine in Henan Province, China, the PFC 2D numerical simulation and surface subsidence field observation was conducted to study the subsidence characteristics of strata with thick unconsolidated overlying strata (680m). Numerical model with dimensions of 2000m 750m was established and mining process with different working face lengths (150 m,200 m,250 m,300 m) and different working face advancing distances (40 m,80 m,120 m,160 m,200 m,240 m,280 m,320 m,360 m,400 m,440 m,480 m) were simulated. The surface subsidence characteristics and displacement field variation of rock strata under different working face advancing distances were observed and analyzed. The results show that with the advance of working face, the structure of subsidence-like basin will be formed in each rock stratum, and the influence range of mining on rock stratum is “bowl-shaped”, and the influence increases with the increase of advancing distance. The unconsolidated layer has a buffer effect on the mining-induced subsidence, and the buffer effect is realized by the expansion of the subsidence area. The movement law of strata under different working face lengths is similar to that under general mining, and the structure of subsidence-like basins will also be formed in each stratum. The influence range of strata after mining is ' bowl-shaped ', and the influence extent increases with the increasing of working face length; the internal subsidence of the unconsolidated layer is more intense and complex than that of the rock layer; the surface subsidence movement shows an obvious 'basin' phenomenon. The field observation data of surface subsidence also confirm the above results.

By Laurent Rus, Bakar Amara, Jean Habimana

The La Fontaine Tunnel in Montreal, Quebec is currently undergoing major structural rehabilitation work and systems upgrade work to comply with current codes, standards and best practices in fire life safety and to extend its lifespan of this 55-year-old immersed tube tunnel for at least another 40 years. The paper discusses design consideration of ongoing works that include structural analyses to evaluate repair strategies for the post-tensioned reinforced caissons, the scheme to repair two leaky joints between caissons, the design of passive fire protection that involved in situ and real scale laboratory tests, and other tunnel systems upgrades.

Jun 13, 2023

By Charles H. Arnold

This topic addresses historic and current techniques of excavating, supporting and lining tunnels of 4 m (13.1 ft) and smaller. Special considerations relate to the economics of working in close quarters and the sizes of tunnel which achieve the required facility in the optimum economic manner are discussed. The excavation discussion includes TBM, conventional and special techniques for hard rock, soft ground, subaqueous, free and compressed air tunnels. Internal and external support methods discusses timbering, steel ribs, bolting, strapping, shotcreting, grouting, and freezing. Lining methods include cast-in-place concrete, concrete pipe, segmented linings, shotcrete, and others.

Jan 1, 1981

By Safdar A. Gill

The technique of installing small diameter caissons (drilled piers) through soft clays and water bearing ganular soil is well established for constructing building foundations. Over the past few years, the method has been utilized for constructing a large number of shafts extending into rock for the Chicago's Deep Tunnel Project. This paper will discuss design considerations for obtaining the most economic ground support system, the impact of construction procedures on the support and lateral pressures for design. Construction procedures will be described along with performance of the shafts.

Jan 1, 1981

By D. E. Walsh

The behaviour of gold particles on a spiral was studied using radioactive gold tracers. The method allowed the effect of particle size, particle shape, pulp density, feed rate, and splitter settings to be studied. Although the method has been successfully applied to other gravity concentrators, it was found that reliable results were more difficult to obtain on the spiral. However, these preliminary results show that provided suitable precautions are taken, the technique is capable of providing valuable information that cannot be obtained by conventional studies, and could be used to better optimize spiral performance.

Jan 1, 1992

By R. L. Loofbourow, Robert R. Miller

Deep, stable, unlined space promises secure, efficient, acceptable solutions to several current problems. With truly favorable conditions, it can be economic as well. The basic requirement is sufficient sound, tight rock at required depth. This and unusual surface requirements point to special testing. An objective is to describe conditions for planners, estimators and contracts. A first stage concept study needn't be prolonged but should overlook nothing significant. Although observations and tests on core are considered essential, time and expense can be cut by supplementing then with tests on walls of rotary or percussion holes. In some places initial drilling could be shallow.

Jan 1, 1981