Search Documents

By William H. Pomroy, Annie M. Carigiet

This U.S. Bureau of Mines report is an analysis of underground coal mine fire incidents occurring in the United States during the 15 years from 1978 through 1992. The fire data used in this analysis were obtained from Federal Mine Safety and Health Administration (MSHA) mine fire investigation reports. Fires were analyzed by year, state, coal bed thickness, mining method, evacuation measures taken, ignition source, burning substance, location, equipment involved, detection method, time of day, number of injuries and fatalities, and method of extinguishment. In all, 164 fires are reported, or an average of 10.8fires per year. The most common ignition source was electricity, the most common burning substance was coal, the most frequent fire location was the belt entry, belt conveyors were the most common equipment involved in fires, and water was the most common extinguishing agent.

Jan 1, 1995

By Keith G. Wallace, Gary K. Rogers

As a supplement to an analysis involving methodologies for the estimation of airflow resistance in shafts used for both ventilation and hoisting, a detailed shaft characterization survey was distributed worldwide. The survey provided detailed information which enabled verification of recommended velocities and established limitations on fill factors and relative velocities. This paper evaluates the information obtained for 37 shafts and presents a statistical evaluation of the results. Apart from airflow rates, conveyance rates, and physical characteristics, qualitative information regarding means of conveyance stability and velocity control techniques at unloading and loading points are also presented. Calculations of fill coefficient, free area velocity, and most importantly, relative velocity between the airflow and hoist, are conducted. These results are presented by frequency diagrams which illustrate the trends, as well as provide limitations for these parameters. The data illustrates that, commonly, the fill coefficient for two or more conveyances, does not exceed 30 %. A limit of 50% is suggested for a single conveyance shaft. A recommended free area velocity of 10 m/s (1,970 ft/min) for combined ventilation and hoisting shafts, is sup- ported by these results. Relative velocities of 30 m/s (5,905 ft/min) are most frequent and 50 m/s (9,840 ft/min) being a practical maximum.

Jan 1, 1987

By Salama

In the conventional approach, the separator feed incremental masses are assumed to be concentrated at the midpoints of the density or size intervals and subjected to a model partition function. The resulting separation predictions would change if the locations of the incremental masses were changed. As a result. the predicted results depend on the choice of locations where the feed incremental masses are concentrated in the density or size intervals. A technique that utilizes the cumulative-mass-distribution of the circuit feed and the derivative of the partition (separation) function relative to density or size variables is proposed. The proposed technique eliminates the dependency of the predictions on choice of where the feed incremental masses are concentrated within the density or size intervals. Since the proposed technique is based on the cumulative masses at the upper limits of the density or size intervals, the technique produces a single prediction whereas the existing techniques produce predictions that depend on where the incremental masses are concentrated. In fact, it has been demonstrated that the existing conventional technique, in which the incremental masses are concentrated at the midpoints of the density or size intervals, is a first-order approximation of the technique proposed.

Jan 1, 2002

By N. R. Billette

In 1982 and 1983, a study was undertaken to analyse the applicability of Elbrond?s analytical model to suit the needs of Lake Asbestos of Quebec in their computerized open pit planning and scheduling strategy. The immediate goal was the assessment of the optimal allocation of trucks and the determination of the extra cost of in-pit blending. Data from 45 tonne trucks was used to estimate the mine capacity based on a fixed assignment policy. The tonnage yielded by the analytical model was compared with the results of a simulation program. Another point that the study high- lighted was the definition of efficiency parameters for the haulage system: shovels-trucks-crusher. The efficiency, both of the utilization of financial resources and of the operations, for the overall system reaches optimal values in very precise conditions for the number of pieces of equipment in operation. Such a parameter is proposed as a standard for the definition of an optimal number of trucks and shovels in operation. Deviations from this optimum do occur in a well-planned system for qualitative goals. These can then be quantified in terms of costs to the mining company.

Jan 1, 1986

This paper details the development of a functional work index that characterises the relationship between the energy that is imparted by a Roller Press into materials, against the resultant size reduction achieved. Such a Roller Press work index is necessary for this new grinding technology to differentiate it from Bond's grinding work index, and to clear up confusion that arises with such a comparison to Bond. The energy usage in a Roller Press does not follow Bond's "Third Theory of Comminution" but rather Rittinger's theory of new surface creation. The relationships for such a work index have been developed from the viewpoint of an equipment manufacturer with the hope that they will be of assistance to the minerals industry in the design of grinding circuits incorporating Roller Press comminution. The work index contains modification factors that reflects the effect of oversize, fines, moisture. closed-circuit operation and roll surface characteristics on the energy verses size reduction relationship. It has evolved from the results obtained from testing of a wide range of ore and mineral types that include bauxite, coal, kimberlite, limestone, iron and chrome ores, base metal and gold ores. The results show that even for such a diverse range of materials, they all demonstrate similarities of behaviour when comminuted in a Roller Press.

Jan 1, 1997

By E. Finch

Beneficiation tests were conducted on samples from three ore zones in the Los Monos, Navay orebody in Táchira State, Venezuela as part of an overall feasibility study. The scope of work included ore sample characterization, flowsheet development, and optimization of beneficiation variables on a bench scale followed by confirmation on a pilot plant scale. Phosphate in the ore samples occurred primarily as francolite and was associated with quartz, kaolinite, and feldspar. Liberation of the phosphate began at 589 microns (28 mesh) for the main ore zone sample and at 295 microns (48 mesh) for the lower-grade ore zone samples. Development tests on simulated mining composites demonstrated that the samples responded well to 589 micron (28 mesh) grinding, two stages of high intensity scrubbing, conditioning at high % solids with caustic and equal amounts of tall oil and fuel oil, and separate coarse and fine flotation circuits with one stage of roughing and two stages of cleaning (reflotation). Concentrates in the range of 31.5-34% P205 with recoveries from 64-70% were obtained from the mining composites. Product quality for all concentrates in the range of 31.5 % P205 was good; 1.40 CaO/P205 and 0.04-0.05 minor element ratios. Confirmation testing in a continuous pilot plant produced results similar to those achieved in the laboratory.

Jan 1, 1993

By F. Soumis

This paper describes an integrated procedure for the very short term production planning of an open pit and the execution of this plan: the truck dispatching. Integration of plan and dispatch means that the plan is realistic so that its objectives can be realized by the dispatch. This realism is obtained by supplying the plan optimization, which involves mixed integer programming, linear programming and non-linear programming, with experimental O.R. models of waiting and blending. The arrangement of these models in the computer programm has made it possible to obtain very short computing time for the planning in spite of the width of the optimisation. The dispatching of a truck is made by solving a classical assignment problem for each dispatch over a horizon of the expected*next 10-15 trucks to request dispatches. This deep-reaching dispatch procedure uses the continuously arriving information about trucks' positions and shovels situations and models by probability functions the expected waiting time of shovels and trucks. In this manner trucks and shovels are synchronized and last moments' opportunities for productivity gains can be obtained. The dispatch procedure takes .5 second on PDP11. This integrated planning and dispatch procedure gives high productivity while ensuring good blending. Results from the Mount Wright mine of the Quebec-Cartier Mining Co., where the integrated procedure has been installed on the existing computer equipment PDP11, are included.

Jan 1, 1989

By Stanislaw Nawrat, Waclaw Dziurzynski

An increasing concentration of coal production, especially in the circumstances of intensive methane inflow makes the coal mine managing staff apply new techniques of safe mining. It paves also the way for scientists to develop new directions of investigations and implementation of state-of -the- art technical solutions. Simultaneously, it could be noticed that the funds assigned for expansive 'En situ ' investigation are continuously decreasing. Better and better results are reached when applying computer technique in calculations of the parameters of ventilation process. Recent theoretical and experimental investigations of air and gas (methane) flow in longwall areas with caving, combined with the implementation of methane drainage system allowed to create, a mathematical model and consequently to elaborate a computer supported numerical simulation of discussed phenomena. The mathematical model has been modified and the simulation program was prepared in such a way that the software is convenient for a user looking for an optimal solution. The paper presented the methodology of optimal choice of following parameters: - ventilation system - rate of flow through the wall. The procedure takes into consideration keeping a safe level of concentration methane in air flowing through the longwall as well as the criterion of maximum methane concentration within the methane drainage pipe line. Results of variant computer simulation regarding the longwall with caving are shown in graphs and tables.

Jan 1, 1995

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

Land management planning is an important issue in all jurisdictions, especially as it relates to mineral development. These planning documents are prepared at different intervals and reflect the realities at the time that they were prepared. The Seven Questions to Sustainability developed during the North American Process of the Mining, Minerals and Sustainable Development (MMSD) project are proposed for the evaluation of Land Use Plans as they relate to Mineral Development. This paper provides the background to the Seven Questions to Sustainability and how it can be applied to the evaluation of land use plans with specific reference to Resource Management Plans developed by the U. S. Department of the Interior?s Bureau of Land Management in Nevada. While this paper is focused on Nevada, the approach is broadly applicable and may be used in other planning regimes.

Jan 1, 2007

By Kirk H. P. E. McDaniel, Mark T. Strever, Keith G. Jr. Wallace

This paper presents the design and installation of an underground ventilation remote monitoring and control system at the Waste Isolation Pilot Plant. This facility is designed to demonstrate safe underground disposal of U.S. defense generated transuranic nuclear waste. To improve the operability of the ventilation system, an underground remote monitoring and control system was designed and installed. The system consists of 15 air velocity sensors and 8 differential pressure sensors strategically located throughout the underground facility providing real-time data regarding the status of the ventilation system. In addition, a control system was installed on the main underground air regulators. The regulator control system gives indication of the regulator position and can be controlled either locally or remotely. The sensor output is displayed locally and at a central surface location through the site-wide Central Monitoring System (CMS). The CMS operator can review all sensor data and can remotely operate the main underground regulators. Furthermore, the Virtual Address Extension (VAX) network allows the ventilation engineer to retrieve real-time ventilation data on his personal computer located in his workstation. This paper describes the types of sensors selected, the installation of the instrumentation, and the initial operation of the remote monitoring system.

Jan 1, 1995

By Raj K. Rajamani, Poly K. Songfack

The slurry transport within the ball mill greatly influences the mill holdup, residence time, breakage rate, and hence the power draw and the particle size distribution of the mill product. However, residence-time distribution and holdup in industrial mills could not be predicted a priori. Indeed, it is impossible to determine the slurry loading in continuously operating mills by direct measurement, especially in industrial mills. In this paper, the slurry transport problem is solved using the principles of fluid mechanics. First, the motion of the ball charge and its expansion are predicted by a technique called discrete element method. Then the slurry flow through the porous ball charge is tackled with a fluid-flow technique called the marker and cell method. This may be the only numerical technique capable of tracking the slurry- free surface as it fluctuates with the motion of the ball charge. The result is a prediction of the slurry profile in both the radial and axial directions. Hence, it leads to the detailed description of slurry mass and ball charge within the mill. The model predictions are verified with pilot-scale experimental work. This novel approach based on the physics of fluid flow is devoid of any empiricism. It is shown that the holdup of industrial mills at a given feed percent solids can be predicted successfully.

Jan 1, 1995

By K. Holmberg, D. Herriot

This paper by Mr. McIvor is yet another contribution to the eternal controversy surrounding the benefits, or otherwise, of high circulating loads in closed circuit grinding. Throughout the paper it is difficult to establish whether the author is referring to effects relating to the mill, classifier, or to the overall circuit. Table 1 is put forward as indicating the advantage of operating at high circulating loads. From the two (it would be interesting to see more) product sizing points provided in each case, the conclusions to be drawn are that cases one and two have very similar size analyses. The third case, however, indicates a much flatter curve, that is to say, higher fines production and a very wide spread of size ranges. If the objective of this circuit is to provide a closely sized product with minimum overground slimes to the downstream process, then it would appear to be the less "efficient" by far. No data is given for product pulp densities either. The term "efficiency" should never be used without a careful and clear definition. In this case, "efficiency" is used to express an apparent percentage reduction in operating work index (Bond) from the measured "standard" at 250% circulating load operation. The Bond calculation is itself based upon

Jan 1, 1990

By A. W. Scaroni, C. Y. Tsai

The effect of particle size and composition on the pyrolysis and combustion of a pulverized bituminous coal in an entrained-flow reactor has been investigated. Predicted time-temperature histories of the coal particles and experimental weight loss data indicate a strong coupling of heat and mass transfer to the pyrolysis and combustion rates. A higher combustion rate following ignition was observed as particle size was increased to 112 µm (about 140 mesh). This is related to a higher particle temperature after ignition for the larger particles. Although the heating rate before ignition decreases with increasing particle size, higher slip velocities and surrounding gas temperatures for the larger particles promote early ignition. The presence of liptinite in the coal increases the weight loss rate before and immediately after ignition. Similar behavior was observed for pyrolysis. Fractions of an HVA bituminous coal that were rich in mineral matter or semi-fusinite were found to have a higher heterogeneous char combustion rate than vitrinite-rich samples.

Jan 1, 1987

By J. R. Stoltz, E. Thompson, S. Pattee

On May 15 and 16, 1999, a mine ventilation survey was performed in the 705-m- (2,312-ft-) deep Cayuga Mine, Cargill Salt Division, Lansing, NY. The purpose of the survey was to develop a numerical model of the existing ventilation system and to perform a computer simulation study for long-term environmental and ventilation planning. Because the natural ventilation pressure (NVP) has significant effects on the ventilation system at the Cayuga Mine, there was a need to assess the NVP acting in the mine. Due to the ventilation arrangements in the Cayuga Mine, the authors decided to use the direct-measuring method to determine the NVP by measuring differential pressure across the automatic fan door. This difference in pressure was measured immediately after the fan was stopped and the automatic door was closed to stop the flow throughout the entire mine. To show seasonal changes in NVP, two additional measurement for NVP were performed, one on Aug. 22, 1999, during the hot (summer) season, and another on Feb. 6, 2000, during the cold (winter) season. The mutual interaction between the natural ventilation pressure and the main fan at the Cayuga Mine is also discussed

Jan 1, 2003

By Joginder S. Bhore, Francis M. Keville, David E. Puza, Roger C. Borggaard

A portion of the Massachusetts Bay Transportation Authority's Red Line Extension through Somerville, Massachusetts consists of 1,553cm (5,092 LF) of hard rock tunneling 6.7m (22 ft.) diameter horeshoe, 148m (485 LF) of mixed face tunneling, 7.2m (23 ft.) diameter circular, beneath an active railroad in a heavily commercialized business district. This paper will deal with the excavation of the mixed face area without the use of a shield. It will address the special excavation and support problems encountered during tunneling operations using the floating crown bar and modified spiling methods. Topics covered will include excavation and support methods, cement grouting, compaction grouting, and instrumentation. PROJECT DESCRIPTION The Davis Square to Porter Square Tunnels and Shafts Somerville/ Cambridge, Massachusetts is part of the Massachusetts Bay Transportation Authority's (MBTA) 5.1km (17,000 ft.) Red Line Extension. This extension runs from Harvard Square, Cambridge, to Alewife Brook Parkway, Cambridge through Somerville. This portion (MBTA Contract #091-106) required the excavation and concreting of 1,701m (5,580 LF) of single track twin tunnels consisting of 1,553m (5,092 LF) of conventional hard rock tunneling under 56 residential properties and 148m (485 LF) of mixed face tunneling beneath an active railroad in a heavily commercialized business district. The mined diameter of the mixed face tunnel is 7.16m (23.5 ft.) Access to the tunnel was via the Summer Street vent shaft, and the two Grove Street access shafts where all tunnel excavated materials were removed.

Jan 1, 1981

By A. M. Al Taweel, S. M. El Mofty, T. A. Hassan, M. R. Moharam, A. M. Ramadan

The axial mixing characteristics of a pilot-scale flotation column were investigated with the objective of identifying means to mitigate the extent of axial mixing that adversely affects its grade/recovery performance. A wide range of design and operating conditions was investigated and the experimental results, obtained using the dynamic response method, were analyzed using three axial mixing models. The dynamic response of the column can best be described using the axial dispersion model. The results obtained suggest that the value of the axial dispersion coefficient, EL. can be signi6cantly reduced by judicial selection of hydrodynamic conditions and/or the use of column inserts that suppress the onset of hydrodynamic instabilities inherent to the operation of conventional flotation columns. Up to 40% reduction in the value of EL was thus obtained by using spargers that produce more uniform bubble sizes, while up to 30% reductions were obtained by controlling the residual frother concentration.

Jan 1, 1995

By Cathleen J. Webb, Arden D. Davis

Begun in 1992, an abandoned and inactive mine inventory in the Black Hills National Forest has resulted in a hazard ranking of the most severely affected sites. For purposes of the inventory, the Black Hills were divided into three main regions: the northern Black Hills, with primarily gold mines; the central Black Hills, with pegmatite mines and some gold mines; and the southern Black Hills, with primarily uranium mines. A computerized data base has been developed along with standard forms for field crews. The forms were designed to provide maximum compatibility with other abandoned mine inventories on various federal and state lands. Measures recommended for the most hazardous and heavily affected sites include regrading of unstable slopes, fencing of open shafts, and remediation of the most severe acidic mine drainage problems. Specific examples are illustrated where remediation and safety measures were recommended or have been implemented. The vast majority of the sites, however, needed little or no remedial action.

Jan 1, 1995

The minerals industry contributes to the economic growth, prosperity and quality of life of nations, particularly in areas where there might be limited opportunities for employment in other sectors. However, notwithstanding their economic importance, the minerals extraction and processing industries are considered to have significant impacts on the surrounding environment. In recent years many mines have implemented modern monitoring technology and modelling of the monitored environmental parameters to provide scientifically proven indicators about the state of the environment. The flexibility required by the minerals industry to respond dynamically to a changing natural, social and economic environment has become a major consideration. Whilst the notion of continuous improvement is embodied within most environmental management systems, what is now required is a structured audit trail which tracks the flow of resources through the production process to the ultimate environmental impact associated with their consumption, transformation and disposal. Imperial College is coordinating an EC funded project, which is developing a methodology to minimise the ?full life-cycle? impact of metalliferous mining projects, adopting an integrated approach to production and process design, and the costs involved. In order to develop a life cycle assessment (LCA) system that will incorporate different types of data related to the minerals extraction operations, a data inventory was designed and coded in an object-relational database model. The calculation procedures accounting for the input/output balance of the alternative scenarios for mining production, processing, waste disposal, monitoring, and their financial implications are being programmed into a software system. This paper presents the rational and innovative aspects of this work. The methodology developed for the life cycle database is illustrated for the mining production and gaseous emissions components of the system.

Jan 1, 2003

By Y. T. Auck, M. E. Kukura, L. G. Stevens

At its Technical Development Center in Tucson, Arizona, the UOP Mineral Sciences Division operates a completely integrated pilot plant testing a proprietary process for the extraction of nickel from limonite/saprolite ores. The process is based on the reductive roast- ammonia leach procedure now employed in several plants around the world. The process improvements are such that nickel extractions well above that experienced in these processes are possible, particularly on the more garnieritic/saprolitic ores. This paper will describe the process and the results of process development studies. The data show that pilot plant results confirm those obtained on the smaller laboratory and bench scales of experimentation.

Jan 1, 1979