Search Documents

By D. I. Smith

Constructing tunnels in congested urban areas requires tunnels to be placed closer together and with less cover than was previously necessary. Contract CQ031 of New York?s East Side Access project will construct four six-meter diameter bored tunnels in a three-up one-down ?T? configuration, with less than three meters of soil between the tunnels. Mixed-face rock and glacial till conditions with a high ground water table will be encountered under active railroad yards. The tunnels will also pass beneath the busiest railroad interlocking in North America with cover as shallow as three meters. This paper discusses the challenges of designing segmentally lined tunnels for these conditions.

Jan 1, 2008

By K. Boakye

This paper presents the results of a review of historic blast design practices at the Dragon Products Company, LLC (Dragon) Quarry Operation, along with the results of two different blast design vibration monitoring programs. A blast pattern design modification was initiated to determine if production volume per shot could be increased and highwall instability could be decreased. A vibration monitoring program was undertaken to investigate peak particle velocity (PPV) and relate the data to the blastability of the jointed onsite rock mass, utilizing the relationship between PPV and dynamic stress and strain. The Dragon Quarry Operation has historically used a 6-in. diameter, 14-ft by 14-ft production blast pattern, with blast holes loaded manually using cartridge style explosive products. In 2011, Quarry Operations introduced a 6-in diameter, 16-ft by 16-ft production blasting pattern, using pre-mixed, truck-loaded, bulk emulsion/ammonium nitrate/fuel oil (ANFO) blends. This paper summarizes the results of the blast design modifications, the results of the vibration monitoring data, and describes how production blasting and excavation at the Dragon Quarry has benefited from such modifications.

Feb 27, 2013

By Ted Nye

This paper describes a number of aspects of the design and construction of a driven tunnel which forms part of the Boggo Road Busway project. The driven tunnel is 430m long with an excavated width of 15m and a full tunnel excavation height of 8m. The first section of driven tunnel was excavated under the heritage listed Boggo Road Jail for a length of 120m. The main jail buildings and perimeter walls were built in 1908 and are of brick construction. Ground cover over the tunnel beneath the jail site varied from 5.5m to 8m and as a consequence the predicted settlement values and their potential to cause damage to the buildings were critical to determining and obtaining approval for the selected tunnel alignment. The geology along the driven tunnel alignment was very variable, providing mixed face tunneling conditions and ranging from surface residual soils to high strength rock at depth. The maximum ground cover above the driven tunnel is 20m.

By D. Brady

The need for onsite gas monitoring during, or following, a major incident at an underground coal mine has long been recognised. Recommendations from inquiries following Queensland mine disasters have included ?qualified persons and equipment for rapid analysis of gas samples be available in times of emergency? and that ?this may be accomplished by either mobile laboratories or laboratories established in each mining locality.? Following the Moura No. 2 disaster, the Queensland Government allocated funds to Simtars for a mobile laboratory to respond should such a disaster occur again in the future. This vehicle was commissioned in 1997 and has been used at many mine sites under a wide range of scenarios. Simtars, armed with over ten years of operational experience with this mobile laboratory, has taken an active role in the design and construction of a modernised replacement unit. With a twenty point tube bundle system and ultrafast gas chromatograph the result is, arguably, the best equipped mobile gas analysis laboratory for mine emergency response in the world. This paper outlines the features of the new laboratory, its capabilities and the philosophy behind the design and inclusions.

Jan 1, 2012

Construction of the Boddington Mine 130 km (81 miles) southeast of Perth, is about 89 percent complete. When the $2.9-billion development is finished, it will be the largest gold mine in Australia, producing 31 t/a (1 million oz/year), according to project majority owner Newmont Mining. Newmont?s acting regional group executive for Asia Pacific, Philip Stephenson, told a gold conference in Australia that the project would be ?the biggest thing for Newmont this year.? The project has been in the works for more than 10 years, but because of a three-sided ownership and fluctuating gold prices, it struggled to get started. However, Newmont is set to become the full owner of the project and is moving ahead on the low-grade project. ?We are targeting annual production of 31 t/a (1 million oz/year) for each of Boddington?s first five years. When it is in full production, Boddington will be the largest gold mine in Australia,? Stephenson said. ?The mine?s costs applicable to sales will be around US$9.64/g (US$300/oz) and that puts Boddington into the bottom quartile of the global cost curve. ?Strategically for Newmont, Boddington coming on-line will improve Newmont?s overall global geopolitical risk profile as it delivers greater exposure to an AAA-rated country.? Boddington has a projected mine life of 20 plus years. It has current total reserves of 622 t (20 million oz) and rising. Stephenson said Boddington has the largest reserve base of all gold projects in production or those that are about to go into production in A-rated countries or better. And it will be an important asset for many years to come. Newmont will acquire the remaining 33 percent share held by AngloGold Ashanti in a deal that should be concluded in the next two months. Australian miner Newcrest Mining Ltd. had exited the joint venture several years ago. Newmont had come into the project through the take-over of then Australia?s leading gold miner Normandy Mining, while AngloGold Ashanti gained entry through

Jan 1, 2009

By D. R. Gagnon

Mining companies are continually looking for product-ivity and efficiency improvements with their equipment to reduce operating costs. This paper will review the results of a productivity analysis conducted at the Luscar Ltd. Boundary Dam and Bienfait mines near Estevan, Saskatchewan using a Computer-Aided Earthmoving System (CAES) installed on a track-type dozer. The CAES TTT system is a Global Positioning System that provides the operator with constant survey guidance. The study includes a productivity comparison between two similar test sites, one with the aid of the CAES system and the other, without. The CAES TTT system shows a productivity improvement of between 20 and 35% in the reclamation slope leveling application. Even with the CAES TTT system deactivated, some of the advanced features of the system were used to: retain terrain data for volume calculations; track the equipment position; and, accurately record and separate idle time from working time.

Jan 1, 2002

By Jacek B. Stypulkowski

This paper discusses the challenges faced by the design team of the under-river crossings of electric transmission feeders in New York City, a densely populated urban area. The under-river crossing of a 345 kV feeder was initially designed as Horizontal Directional Drilling (HDD), but was redesigned as a utility tunnel because of site con¬straints on both sides of the river. Multiple studies addressed location, available tech-nologies and costs. Multiple soil investigation phases addressed design aspects of HDD, as well as tunneling. Contractual issues varied from a design build alternative with Geotechnical Data Report (GDR) to design tender approach with GDR & Geotechnical Baseline Report (GBR).

By David Caiden, Geoffrey Fosbrook, Jaidev Sankar, Donald Phillips, Jon Hurt, Anil Parikh

This paper will cover the progress being made on Phase 1 of New York’s Second Avenue Subway line. It will include a description of construction progress on the first contract to be let, which consists of a 248 m (815 ft) long launch box, 3.9 km(2.4 miles) of TBM tunnels and a tunnel sump; the packaging strategy for the remaining work; and the progress through Final Design of the remaining packages, including the two large span rock cavern stations.

Jan 1, 2007

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

By M. J. Gilbey

London Underground is the oldest and one of the deepest Metros in the world. The temperature of the Underground has been increasing over the last 100 years, mainly as a consequence of increases in train service. Further increases in train service are planned in the coming years to meet the predicted growth in passenger demand. Unabated, the additional service will increase temperatures on the Underground. London Underground Limited (LUL) has therefore set up the Cooling the Tube Programme (CTP) to tackle the issues of thermal conditions on the Underground. Some of LUL?s studies and cooling methods have borrowed experience and techniques from the mining industry; some of methods used or proposed may in turn be of interest to the mining community. This paper presents a background into the sources of heat on the Underground network, the manner in which the heat is presently dissipated, the analysis of future temperatures and criterion and a number of means and methods being used or proposed to cool the network in an environmentally sensitive manner.

Jan 1, 2009

By J. McMurray

Introduction Uranium was recovered from mining of collapse breccia pipe deposits in the Arizona Strip district in northwestern Arizona (Figure 1) intermittently between 1956 and 1990, with cumulative production having totaled 23.3 million pounds of U3O8 (8960 tU) at an average grade of 0.6% U3O8. Production was suspended in 1990 because of low uranium prices, but the recent resurgence in market price once again makes the breccia pipe deposits potentially attractive exploration and development targets. This paper describes: (1) formation of the pipe structures and their metallogenesis; (2) mining and milling of breccia ore; and (3) potential roadblocks to development of new breccia pipe mines. Breccia Pipe Formation Formation of the breccia pipes began in cave systems formed during development of karst topography in the Mississippian Redwall Limestone. The karst Redwall surface was eventually covered by up to 900 meters of shallow marine to continental sediments ranging in age from Pennsylvanian to Triassic. The pipes were formed by progressive upward stoping caused by groundwater ascending under hydraulic head along near-vertical faults, joints and fractures. The stoping process involved both chemical disaggregation and mechanical failure of roof and wall rock. Upward stoping of successively younger units allowed for upward propagation of a pipe and resulted in a chimney-like column of breccia between the steep walls of the pipe. Syndepositional thickening of sedimentary units of varying ages indicates that pipe formation began as early as early Pennsylvanian time and continued intermittently through Triassic time.

Jan 1, 2007

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

By L. Kulik, J. den Drijver

Rhenish lignite will continue to play an indispensible role in the energy mix of the German Federal Republic for a long time to come. The use of lignite for electricity generation, upgrading and, if necessary, as a raw material is geared to the long term. The holistic management of opencast mines underpinned by approval law in the long term and a stronger focus on man, the environment and nature contribute to the acceptance of the mines by the local population. The same is true of state-of-the-art lignite uses: as regards their operational flexibility, lignite-fired power plants are ideal partners for the expansion of renewables. It is along these lines that RWE is continuing its power plant renewal programme as planned. With a view to that which will be conceivable the day after tomorrow, RWE is researching future technologies today in order to meet objectives such as security of supply, profitability and environmental compatibility to the same extent in the long term. Another important contribution to acceptance is public transparency and communications as means to support approval procedures and the implementation of measures in all areas related to lignite mining and utilization.

Jan 1, 2011

By Janet A. Flinn, David G. Fileccia

Machine guidance and control systems have become more pervasive in the mining industry in recent years but not always from mining-experienced providers. Dozers, motor graders, scrapers, excavators, shovels, draglines, drills and haul trucks are just a few examples of the types of heavy machinery now equipped with global positioning system (GPS)-aided guidance systems. While equipment manufacturers are offering their own software, many only supply solutions for the machines they produce. The proliferation of GPS equipment manufacturers entering the machine guidance and control arena has resulted in a multitude of makes and models of GPS receivers. Some of these companies also produce their own guidance software. But they usually just specialize in a narrow range of heavy machinery. So customers are forced to use multiple systems and face new challenges in implementation, training, reporting and inter-system communication.

Jan 1, 2006

By J. Kretschmann, N. Nguyen

"The Vietnamese economic growth of more than 5% per year leads this country to an enormous demand for raw materials. In the duration of ongoing expansion, the big challenge in the coming decades will be to make this process as sustainable as possible when it comes to economic, environmental and social objectives. Risk management especially in occupational safety and health (OSH) in enterprises is one of the most important tools to achieve this aim. But until now, this has not been taken into priority by Vietnamese coal mining enterprises. Main reasons for this situation can be found in deficient legislative conditions and in non-synchronized risk management systems. In contrast, Germany has implemented an adequate legal system and the German mining industry has gained lots of experiences in risk management, especially in occupational safety and health. This paper seeks to point out specific challenges how to improve occupational safety and health in Vietnam by transferring and applying German methods and standards."

Jan 1, 2011

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert systems designed for real-time processing plants that also include the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. [1,2] In spite of the fact that significant performance increases have been achieved using these systems they are not perfect and can be improved. They suffer from the static nature of their rules and to a degree the process models. There is an opportunity to further increase system performance by systematically taking advantage of the tremendous amount of data produced by the expert system to improve the design, the heuristic rules, the model topologies and the use of the models. Data mining refers to extracting or mining knowledge from large amounts of data where the objective is to automatically analyze, classify and summarize the data to automatically discover and characterize trends in it and to automatically flag anomalies. [3] Clearly, modern process control systems are capable of collecting vast amounts of data. Without a doubt, these data contain important information on the operation of our plants and their ultimate optimization. Coupling the information mined from these data with Expert Control Systems should produce more effective control and greater knowledge of the grinding process and the flotation process. Now, with the advent of effective monitoring of entire minerals plant electric consumption it is possible to not only optimize plant production in real-time it is possible to analyze total plant electrical consumption and incorporate it into the plant control logic thereby improving the overall plant economic performance. This is particularly important with the ever more complex power contracts that plants operate under.

Jan 1, 2012

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By J. M. Hollow, D. E. Walsh, H. K. Lin, J. L. Oleson

At the Fort Knox Mine, Fairbanks, Alaska, carbon fines are generated during stripping, acid washing and kiln regeneration operations. Carbon fines are collected by a filter press because of their gold value. Samples of the carbon fines show that they consist of 20-30% carbon, 70-80% grit and 0.17-0.68 kg/t (5.0-19.9 oz/st) gold. About 80% of the gold values in the carbon fines used in this study are in a form of recrystallized free gold grains, with the balance being adsorbed gold on the carbon. High recoveries of gold and carbon were obtained in laboratory tests using froth flotation, with a high rejection of the grit.

Jan 1, 2001

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008