Search Documents

By George R. Huebner

The White Pine Copper Company, subsidiary of Copper Range Company, is located in the Upper Peninsula of Michigan. The offices, plant, and mine are six miles south of Lake Superior in Ontonagon County. Employing 1700 people, White Pine is the largest single industry in the Upper Peninsula. 970 underground employees produce 16, 700, tons of ore daily. From this tonnage 363,400 pounds of refined Lake Copper are produced in various shapes as specified by the customer. The following paper explains the geology of the ore body and briefly outlines present mining methods. It enumerates the reasons for considering longwall mining of a hardrock* ore body and the preliminary investigations leading to the decision to undertake the initial test panel. Selection of the initial test panel location is covered in detail. Equipment choice and reasons for that choice are described as well as selection and training of personnel.

Jan 1, 1964

By Richmond Bennett

Airborne geochemistry became a reality with the advent of a high-sensitivity airborne gamma ray spectrometer with large volume NaI (TI) crystal detectors. Small variations in the concentration of potassium (as K40), thorium (as T1208) and uranium (as B1214) along the flight lines can be determined by measuring the gamma radiation with a sensitive airborne spectrometer. Small volume crystal spectrometers are useful only for detection of major surface uranium (Bi214) variations, but the large crystal volume system is an airborne geochemical exploration method capable of locating hydrothermal mineral deposits. Radioactivity as a guide to ore has been discussed in the literature by Damon (1950), Gross (1952) and others. The theoretical basis is that potassium, thorium, and uranium are concentrated in late stage solutions during magmatic crystallization. Thorium and uranium are concentrated in late stage liquids because their large atomic radius and high ionic charge prevent them from entering into the crystal lattice of common rock-forming minerals (Rankama and Sahama, 1950). Potassium, which has a large ionic radius and small charge, also can be concentrated in the high water content late stage fluids (Heier and Adams, 1964). A large proportion of uranium and thorium in rocks occurs around grain boundaries of the essential rock-forming minerals (Hurley, 1950). Uranium and thorium substitute for zirconium in zircon, a comparatively early forming mineral. However, most of the thorium and uranium is concentrated in residuals where they can be fractionated and incorporated into allanite, monazite, xenotime, and other minerals.

Jan 1, 1970

By W. J. Mahoney

A good quality assurance program at a coal mine or power plant is accurate, timely, and consistent. The quality analysis is accurate due to a complete sampling of the coal stream loaded into the unit train. The sample analysis is accurate because standardized testing procedures are applied. Once the analysis is completed, the results must be communicated to the electric utility in a timely manner. The electric utility needs the results to better manage the coal inventory at the power plants. A quality assurance program can also help the mine deliver a consistent product to the electric utility's power plants. The importance of the three major tenants for a good quality assurance program: accuracy, timeliness and consistency, are based on major changes that are taking place in the electric utility industry.

Jan 1, 1994

By C. K. Blankenship

The competitive forces now driving the electric utility industry and the constraints of regulation at all levels are changing the way we will all do business now and into the next century. Utilities are using every technological tool at their disposal to find optimum solutions to challenges in every aspect of operations. In fuel planning and procurement, these tools include models that predict which dispatch line-up will comply with environmental regulations at minimum cost. This paper presents how those tools are being used for Duquesne Light Company.

Jan 1, 1995

By Rene Padilla, Siyanda B. Mngadi, Gerrie van Aswegen, Peter Stonestreet

While many mine tunnels are developed through ground that must be riddled with the sources of small (and larger) mining induced seismic events, recorded by the mine seismic monitoring systems, we do not see planar discontinuities classified as seismic sources in the geotechnical databases. Here we list criteria that may be useful to identify discontinuities in drill core which are dynamic slip surfaces, parts of mining induced seismic sources. Such shear rupture surfaces in core would generally be powdery, cohesionless, and rough on cm scale. Finely broken rock and rock flour may be found in the core boxes at the discontinuities. Slickensides would be soft (easily destroyed) and kinematically consistent with the local stress field. In some cases, a cross fabric would be present, orthogonal to the slickensides, being the intersections of en-echelon extension fractures, within the dynamic shear zones, with the shear zone walls.

Apr 26, 2022

By A. Unal

Coal resource characterization usually calls for estimating more than one variable over a block or node simultaneously. Within the realm of geostatistics, each variable has been evaluated independently from the others assuming a lack of significant correlation. Research conducted with coal seams, however, has shown that the variables of immediate interest, such as seam thickness, ash, sulfur content, and density depict some correlation schemes in distinct zones, if not throughout the entire area. The above findings have two immediate consequences : (1) correlation analyses provide guidelines to determine the geologically distinct zones, and (2) where possible, cokriging should be used instead of kriging. This will maximize data utilization decreasing the frequently criticized high estimation errors. The cokriging formulation will also provide more accurate estimates for under sampled variables using better-sampled ones. This is a common case with coal with regard to the non-cored reconnaissance drill holes for which only very few variables were recorded. A case study illustrates the improvements that may be obtained by taking advantage of the intervariable correlations.

Jan 1, 1986

By S. C. Brown, R. C. G. Oliveira

Surface wettability, or contact angle, dictates a number of multiphase ensemble interactions that influence particulate dispersability and adhesion behavior (e.g., filler compatibility] in addition to a number of other phenomena including biocompatibility and bulk powder segregation. The wettability of particulate surfaces significantly impacts nearly all process industries; however, the available techniques to access this quantity are either relative, or tedious-and are application or industry specific. In this study, key features of existing techniques have been combined to design an improved method to delineate particle wettability that is simple, versatile and capable of providing reproducible measurements in an industrial environment.

Jan 1, 2003

By Jerry Demchuk, Allan Flemming, Stephan Day

Luscar Ltd. is currently developing open pit mining plans for the Telkwa Coal Project. Most waste rock is predicted to be non-acid generating but a proportion (less than 20%) is potentially acid generating. The waste management plan includes in-pit and ex-pit disposal of blended and till-capped waste rock, segregation and in-pit encapsulation of strongly potentially acid generating materials, and in-pit underwater disposal of coarse and fine tailings. The paper will present the steps used to design the waste management plan including the development of geochemical design criteria using various tests and theoretical and practical knowledge of waste behaviour.

Jan 1, 2000

By Robert N. Evans, Delon Hampton

During construction of the Washington Metropolitan Area Transit System, the hand-mining of a mixed-face condition was anticipated on a portion of tunnel located in the downtown area of Washington, D.C. The Section, consisting of two circular tubes, extends from Station 12+80, heading in a westerly direction, traverses along a curve under Lafayette Square, and ends in a northwesterly direction at Station 37+62 (see Fig. 1a). It was near the northernmost portion of the section that the mixed-face condition was encountered. Decomposed rock was first encountered in the invert at Station 31+00. From this point the rock gradually increased in height until it intersected the springline at Station 37+62, the project limit. Summarized within this paper are measurements of the soil load on a horseshoe-shaped portion of tunnel located in the mixed face condition. These measured loads are compared to the soil load on tunnels as determined by current design methods. The paper also discusses rib and surface movements associated with the post loading process. Comments will be made on how the presence of a mixed face condition might help or hender the tunnel design and construction procedures.

Jan 1, 1974

By Steven J. Schatzel

A study was made of frictional ignitions in the underground coal mining industry from 1980 to 1992. The population of frictional ignitions was correlated to a variety of potential contributing factors including the mined coalbed, geographic location, mine production, methane gas emissions, and the type of mining equipment in use. The number of frictional ignitions reported in 1991 and 1992 surpassed the annual totals in all previous years included in the study. Most frictional ignitions occur during cutting operations at a coal face by a continuous miner. The average coal production of mines experiencing frictional ignitions is greater than the average of all underground coal mines throughout the survey period. Methane drainage may have produced a drop in the ratio of gas emissions to coal production (E/P) in mines experiencing frictional ignitions.

Jan 1, 1995

By Laurindo De Salles Leal Filho, Arthur Pinto Chaves

The Serrana Process was developed in the 60's to concentrate an igneous low grade phosphate/carbonate ore using tall oil as a collector and corn starch as a modifier in alkaline medium. Nowadays, although tall oil has already been substituted by a new amphoteric synthetic collector, starch hasn't been substituted yet. This study is an attempt towards understanding the role played by corn starch in this specific system. By means of bench scale flotation test, it was observed that corn starch was capable of promoting the flotation of apatite, phlogopite and dolomite. No effect over calcite was observed. The best efficiency of separation apatite/gangue minerals was yielded at the concentration ranges of 17 to 20 mg/l of starch and 13 to 17 mg/l of tall oil. The starch concentration showed a strong influence over the characteristics of the froth produced by the flotation tests, mainly over the volume of the froth and its mineralization.

Jan 1, 1993

By K. N. Han, Q. Xu

The adsorption behavior of gold in ammoniacal solutions on activated carbon was studied. The gold adsorption capacity of the activated carbon and the recovery efficiency were examined. The parameters affecting the adsorption of gold on the activated carbon included temperature, agitation speed, the concentration of cation and anion and the concentration of ammonia. It was found that the maximum gold adsorption was about 10 kg/t of carbon. The recovery of gold by the adsorption, from ammoniacal solutions was found to be dependent upon the initial gold concentration. Under experimental conditions, a gold recovery of 98% was obtained after 120 hrs of adsorption. It was also found that the initial adsorption rate was relatively fast, when compared to the entire adsorption period. The apparent activation energy for the adsorption was determined to be 15.8 kJ/mol. It was believed that the kinetics of gold adsorption on the activated carbon was controlled by pore diffusion.

Jan 1, 1997

By H. Sis, S. Chander

The beneficial effect of a series nonylphenol polyethylene glycol ether surfactants were tested in the flotation of phosphate ores in which the mixture of sodium oleate and dodecane was used as collector. The performance of nonionic surfactants was first tested in the microflotation of pure apatite mineral. Microflotation experiments showed that the recovery of apatite depends on the number of ethoxylation of the nonylphenol surfactants and decreased with higher ethoxylation. The nonionic surfactant with the smallest ethoxylation group used in this research (NP-4) was then tested in batch flotation of phosphate ores. The flotation of three different size phosphate ores was carried out in the absence and presence of NP-4 surfactant. The beneficial effect of nonionic surfactant was obtained for fine size (-35+150 mesh) and very fine size (-150+400 mesh) phosphate ores at different collector dosages studied. But, in the flotation of coarse size (-16+ 35 mesh) phosphate ore the beneficial effect of nonionic surfactant was obtained only at high collector dosages.

Jan 1, 2002

By J. F. T. Agapito

Significant economic benefits can result when rock mechanics is applied within a practical framework and integrated within the other engineering functions of the mine organization. Such application and integration requires management support and understanding of rock mechanics as a practical tool to help attain high standards of safety, productivity and resource recovery. For such an approach, a long-term geotechnical program is needed in most operations to build an adequate data base and to ensure that design and ground control issues are handled in a cost-effective manner. Best usage of rock mechanics in mining occurs when management recognizes the application as a long-term investment, where time is needed to realize good returns. The need for this approach is due to the difficulty in accurately predicting ground conditions ahead of mining. The practical application of rock mechanics must follow an iterative process of design and verification based on site-specific experience to account for geologic and mining impacts. Ground conditions experienced during mining must be used to check the initial mine design and, if necessary, to provide a basis for design modification. Such a practical rock mechanics program includes comparative experience, in situ instrumentation and numerical modeling. The program begins with the geologic site investigation and continues throughout the life of the mine. It is an integral part of mine planning and operation.

Jan 1, 1991

By Kerstin Malmqvist

Simulation technique has been used for a feasibility study of a deep exploration project for massive, sulphides in an old mining district, the Skellefte field. An interactive computerized mathematical model of an ore field and a drilling procedure has been constructed. It is possible to represent varying geological structures. The model also takes in consideration economical factors such as drilling costs and ore values. On this model Monte Carlo simulations and probability calculations are done in order to estimate the outcome of different drilling strategies under varying geological assumptions. Under the specific conditions of the well known Skellefte field, it is found to be possible to even calibrate the mathematical model.

Jan 1, 1979

By F. Dudouit, M. M. Mohkam, F. Renault

The Pannerdensch Kanaal Tunnel is part of Holland’s Betuweroute high speed freight railway project linking Rotterdam to inland of Europe. It comprises of twin tunnels, 1620 m long each, with 8.6 m inner diameter. The Tunnel alignment is situated mainly in sandy formations and under high hydrostatique pressure. The over burden cover varies from relatively high to very low, sometimes much smaller than the diameter. One of the special features of the Pannerdensch Kanaal Tunnel is that, over some 250 m, the twin tunnels are to be bored in a back?lled sandpit. Some 490 000cubic meter of sand has been placed and compacted by vibro-?otation to refill the sandpit. The tunneling machine is a 9.8 m slurry shield manufactured by Herrenknecht. Tunnel lining is precast concrete consisting of seven plus one key universal segments. Other than the special feature of boring through re?lled sand, constraints such a slow overburden while crossing under Pannerdensch Kanaal and some lagoons, as well as high liquifaction potential of sandy formations, render this job very unique of the type. Fine studies were conducted in heading’s stability. And, confinement pressures were determined considering different risks of liquefaction and blowout problems. Both tubes have been successfully bored. Several sections have been monitored. The results are quite interesting and in accordance with contract technical conditions.

Jan 1, 2003

By H. K. Lin

Cyclic voltammetric and potential step chronoamperometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic peaks and one cathodic peak appear on the voltammogram between -0.50 and 0.80 V vs. SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH and cyanide on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2002

By A. F. Klebanov, K. N. Trubetskoy, M. Yu Khoudine, V. L. Postnikov

The information system of monitoring of mine receive layouts is being created In the "ROSUGOL" Company for the prompt analysis of the state-of-the-art of mining operations at under- ground and open cast mines of the Company, rapid and effective decision-making and elaboration of recommendations on the basic directions of enterprise development. The data bank storing the digital mapping and attributive information describing the actual background of mining operations at the enterprises of the Company is the core of the system. The Oracle database management system and the ARC1 INFO geographic information system have been chosen as basic software packages for the Project realisation. The updating of the information will be performed on a regular basis via the transmission of actual digital data on under- ground and open cast mine layouts In ARCIINFO conversion to the central office of the "ROSUGOL" in Moscow. Centralised storage of digital mapping and attributive data, database administration and navigation is effected with the Oracle software package. Access to the data in the operation mode with an interactive display map will be effected with the use of the local computer net of the "ROSUGOL."

Jan 1, 1996

By M. J. Rex, K. L. Wiley, D. S. Ramey

In situ leaching, initiated in 1986 at the San Manuel Mine, was economically developed in 1989. The primary reason for this lag time between startup and viable production was the time required for technical development. The technical development pursued comprised detailed design, development and implementation of in situ well construction methods, formulation of suitable well pattern arrays and the development of extensive hydrogeologic and geochemical knowledge of the mineral deposit. Since 1989, the in situ leaching program has become a viable and cost-effective method to extract copper from the supergene mineralized zone of the San Manuel deposit. The in situ leaching methods that are currently used have been progressively expanded and continually developed. They will become the cornerstone of copper production from the San Manuel oxide mineral deposit. This paper presents an overview of the supergene hydrogeology, current design techniques, drilling methods and well completion, pump determination and setting, solution management and future plans for the increased extraction of copper by in situ leaching methods at the San Manuel Mine.

Jan 1, 1995

By S. G. Malghan

Flotation circuits of a range of complexity are in use for a large number of ores. Since each ore is different and end-product quality requirements are not necessarily the same, circuit configurations of varying complexity are designed. How- ever, certain basic types of circuit configurations can be identified based upon the flotation behavior of the ores. These basic types can be combined to develop the specific f lowsheet configurations for a given ore. This chapter begins with a brief discussion of basic flowsheet configurations. Examples of the flowsheet configurations for a number of specific ores bearing different minerals are then described.

Jan 1, 1986