Search Documents

By J. Bouchard, V. Aubé, A. Desbiens, R. del Villar

The metallurgical performance of column flotation is determined by the concentrate grade and recovery. Although the former can be continuously measured using an on-stream analyzer, the latter must be estimated by a material balance calculation based on seldom verified steady-state assumptions. Consequently, the automatic control and optimization of flotation columns should be performed using secondary variables having a strong influence on the metallurgical performance, such as froth depth, gas hold-up or bubble surface area flux and bias. The aim of this paper is to present a method to get froth depth and bias measurements using virtual sensors. Fractional factorial experiment design for the neural network calibration of the bias sensor, pilot plant results, and eventual industrial applications – including the possibility of achieving effective real-time optimization from bias and froth depth measurements – will also be discussed.

Jan 1, 2003

By Jack M. Jodrey, Neil D. O’Donnell, R. A. Metz

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1992

By L. R. Shotwell, C. F. Voss, R. J. Bastian

Pacific Northwest Laboratory (PNL) currently supports the U.S. Department of Energy's Office of Civilian Radioactive Waste Management in developing and evaluating analytical methods for assessing the suitability of sites for geologic disposal of high-level radioactive waste. The research includes consideration of hydrological, geomechanical , geochemical , and waste package components and the evaluation of the degree of coupling that can occur between two or more of these components. The PNL effort and those of other research groups investing potential waste sites in the U.S. and abroad are producing a suite of computer codes to analyze the long-term performace of the proposed repository sites. This paper summarizes the ongoing research in rock mechanics at PNL involving flow through jointed rock. The objective of this research is to develop a methodology for modeling the coupled mechanical-hydrological process of flow through joints and then attempt to validate a "simple" model using small -scale laboratory test data as a basis for judging whether the approach has merit. This paper discusses the laboratory tests being conducted to develop s joint behavioral constitutive model for the numerical method under development and the modeling approach being considered.

Jan 1, 1986

In his keynote address at the 18th International Minerals Processing Conference (IMPC), R.P. King, director of the University of Utah Comminution Center, said "it will be the application of very fundamental physical principles that is likely to bring major advances in comminution technology (IMPC, pp. 39-45)." It is evident from the literature published in 1993 that many of these fundamental studies, particularly as they relate to single-particle fracture mechanics and mineral liberation, are starting to bear fruit. The beginnings of fundamental mathematical models for design, scale-up and control of comminution systems are now taking shape. Modeling/fundamentals Population balance models (PBM) have been used to describe grinding systems for 20 to 30 years. However, Williams and Meloy (IMPC, pp. 73-79) pointed out some of the inherent problems with this modeling approach and that there is no unique solution for the unconstrained PBM for grinding. Many of the current constraints used to back-fit selection and breakage functions were also shown to have problems. The need for a more fundamental means of determining these parameters was indicated.

Jan 1, 1994

By André Vervoort, Jef Caers

Compound lognormal distributions serve as new generalized distribution laws for analyzing and estimating ore value distributions or related properties such as the average ore grade. These models are an alternative to the well known lognormal distribution. They are the translation of general geological constraints on the genesis of the deposit cumulated in suitable statistical properties. In this paper a maximum likelihood framework is established for estimating the parameters of such laws or parameter functions thereof. It is shown that under certain conditions maximum likelihood estimation is accurate and efficient in estimating the mean value even when relatively few samples are available. The method is based on a numerical maximization of the likelihood function of these models given the data. Confidence limits on these estimates are set up using resampling techniques such as the bootstrap. By this a complete methodology is presented for inference on ore grade distributions such as is shown in an example of gold data from the Merriespruit mine (South Africa) and the diamond size distribution of the Bougban deposit (Guinea).

Jan 1, 1996

By Th. Petropulos

The Zn-Ag-Pb mineralization zone near Molai (Greece) was explored by more, than 60 drillholes. Promising results led to the decision of additional drillholes in order to confirm the expected spatial extension of the deposit. A multiobjective approach is described which optimizes the location of a set of 5 additional drillholes. The decision is based on estimation errors for grade, thickness and depth of the main ore bearing layer, with respect to cut-off values for grade and thickness. The linear combination of these variables defines a favorability index which is used for mapping optimal drillhole locations. The map shows several clusters of favorable cells. A declustrering algorithm is used to select a representative cell for drilling in each cluster.

Jan 1, 1989

By D. III Earley, R. L. Blake

The Bureau of Mines is investigating the potential for in situ mining (ISM) of gold and silver mineralization. This preliminary study examined samples from several types of deposits. It used light optical microscopy and the electron microprobe to characterize the ore and gangue minerals and textural features of these samples. This included the spacial relations between the target minerals and likely natural fluid channel ways. Low-grade disseminated deposit types from the western US were found to contain fracture- hosted or matrix-hosted gold and silver minerals, some of which are encapsulated by quartz or pyrite. Successful ISM application to gold and silver deposits needs this data in order to understand potential problems of the lixiviant reaching the ore minerals.

Jan 1, 1991

By C. E. Zebula, F. F. Aplan, R. S. Datta

The hydrophobicity of oil shale was found to follow the sequence R-5 > Mahogany >> Eastern. Further, hydrophobicity was found to correlate with the total organic carbon (TOG) content, decreasing with increasing specific gravity of raw oil shale pieces. Differences in hydrophobicity from piece to piece indicate that gravity preconcentration would be much more effective for Western than for Eastern oil shales. Purified kerogen concentrates and low specific gravity fractions (<2.0) of raw Western oil shale samples show critical surface tension of wetting values of [y]c = ~35 mNm -1, and for a kerogen concentrate from an Eastern oil shale [y]c = ~46 mNm-l. This infers that dust from oil shale mining operations can be suppressed by surfactant solutions similar to those used to suppress coal dust.

Jan 1, 1988

By Shouci Lu, Keji Sun, Dianzuo Wang, Yiqun Li, Chuang Jin

The dephosphorization of iron ore and reduction in Fe loss in process are currently the foremost technological challenges facing the mineral industry of Meishan Iron Ore. These problems can be resolved to a greater extent by an apatite flotation process which depends on selective flotation reagents. The primary objective of this research work is to develop new type of flotation collectors for dephosphorization of weak magnetic iron ore. Detailed discussion is given on the influence of collector dosage, pH, dispersants and pulp temperature on the flotability of apatite, siderite and hematite using the collectors of Oleyl sarcosinate(OSS), Alkyl polyoxyethylene ether phosphate (AEP) and the mixtures of OSS and AEP A key feature of the flotation was the use of the mixtures of OSS and AEP as a selective collector for phosphate. The effects of chemicals and operational variables on the phosphorus flotation from the weak magnetic iron ores have been investigated. The test results shows that floating the phosphorus minerals with new type collectors can reduce the phosphorous content in the flotation concentrate to an acceptable level of less than 0.20% P with increased Fe recovery.

Jan 1, 2002

By R. Flattery, Z. Agioutantis

Coal and rock pillar design is critical not only for mineral extraction but also for the safety of the mine operators. Pillar strength can be estimated through numerous empirical formulas that are available in the literature, which are typically based on a statistical analysis of case study data. The limitation of most of these equations is that they only considered the width to height ratio and in situ rock or coal strength for pillars in horizontal seams. The adoption of such equations to estimate pillar strength in inclined seams may overestimate the pillar strength and ultimately lead to a poor pillar design. This paper will discuss different techniques that can be used to estimate pillar strength in inclined seams as well as present preliminary modeling results for stress redistribution around inclined pillars. Factors in the parametric analysis include pillar shapes, geometry, and seam inclination.

Mar 2, 2022

By Abdullah Arik

Verification of computer generated reserve models is essential since the computer does not automatically check the validity of methods and assumptions selected by the user and their results. For the computer to do model verification would require an expert system which would perform tests on the model and determine if the model is valid. Since such an expert system is not available, it is up to users to verify the models they develop.

Jan 1, 1995

By John H. Smith

Because of increased pressure from Federal & State Regulatory Agencies, most acid flows will require some sort of treatment prior to being discharged to receiving streams. In many industries, the volumes of liquors are large and their acid content varied. Pressure to minimize costs of waste treatment equipment and land usage makes development of a treatment process incorporating these desires mandatory. "Standard" methods of acid neutralization with lime have been known for years, however, the volume and characteristics of the resultant precipitated solids can create a disposal problem. Also, when standard lime treatment is used, the settling characteristic of the precipitated solids is normally slow. In some instances, the necessity of added dissolved solids removal, (such as iron, needing aeration) add to the problem of concentrating neutralized solids. In a paper published in the September 1970 issue of "Coal Age," *the results of extensive test work by personnel of the Homer Research Laboratories of Bethlehem Steel Corporation, Bethlehem Pa., were reported. This paper dealt specifically with development of a flow sheet to treat acid mine drainage (hereafter referred to as AMD) from coal mine operations. Regulations on discharged water required basic pH and low dissolved iron content after treatment. Liquid flows of over 9 MGD from

Jan 1, 1972

By V. M. Torres

An empirical correlation to detennine laboratory mill grinding time has been developed. Grinding samples to 90 ± 5# below 147 micrometers was required for a flotation testwork at Companhia Vale do Rio Doce (CVRD) Research Center. The initial samples were all below 1 mm in size with different size distributions and work indices (Wi) ranging from 13 to 23 kWh/st. Grinding curves were determined for some initial samples. A correlation was developed between percent retained on 147 micrometers at a standard time and the time required to grind each sample to the required size. This correlation was then used to grind all samples, based on the preliminary grinding model. Finally, a statistical analysis with the size distribution of all samples was performed. The success of using the correlation was confirmed and an equation was determined using the data set.

Jan 1, 1996

By James A. Deane

Strip mine reclamation Fs the process of restoring the land affected by the mining process to its most productive use. This can be timber production, pasture, crop land, wildlife and/or recreational use. The mining companies must determine, through the advice of their technicians, what the most advantageous use of the land will be. If the Company does not own the surface, the owner or owners must be contacted to determine their desires as to how the land should be reclaimed. Many times, in making the plans to restore an area with vegetative cover, the watershed and the quality of the water in the area is overlooked. The water itself must be an integral part of the reclamation plan. Many lakes and/or pits can be created with proper planning. In areas in the Midwest, where lakes are a scarcity, these strip mine lakes can become storage reservoirs for large amounts of water, They can help control runoff and low flow augmentation. The strip mining operation will affect the watershed regardless of whether a reclamation plan in made or not. It is up to the reclamation technician to see that the plan benefits the watershed instead of affecting it adversely. This can be done during the operation by intercepting the water before Pt enters the active pit. Diversion ditches above the highwall will handle the runoff water from the watershed. Water that does gain entry into the pit should be removed as quickly as possible. If the rules and regulations adopted by the Ohio River Valley Sanitation Commission in Resolution 5-60 are followed, water encountered during the operation can be handled with little or no adverse effect to the receiving watershed.

Jan 1, 1965

By D. H. H. Quon, A. Ahamd, G. Pouskouleli, T. A. Wheat

An outline of the contributions of hydro- metallurgical techniques such as sol-gel processing, direct precipitation and hydro- thermal decamposition for the development of high-quality ceramics is given and examples drawn from recent work on both structural (engineering) and functional (electrical) ceramics are discussed.

Jan 1, 1990

By Samara Ali-Ahmad, Keith Hanks, Cindy Pham

The City of Los Angeles will rehabilitate approximately 9 miles of its North Outfall Sewer. This sewer was constructed in the 1920s as an unreinforced concrete semi-elliptical sewer. One of the methods for rehabilitation is to approach the sewer as a pre-excavated tunnel and install pre-cast segmental liners to provide a single pass corrosion resistant, structurally self sufficient project. The estimated cost for this project is $46 million. The project has completed the pre-design study, and the design is now underway.

Jan 1, 2003

By Y. Topkaya, R. E. Johnson, B. R. Palmer, R. B. Bhappu, A. E. Clark, R. P. Bush, L. E. Schultze

The U.S. Bureau of Mines conducted copper exchange capacity (CuEC) tests for six common clays under simulated in situ leaching conditions. Regression equations were obtained from the data expressing the CuEC as a function of Cu concentration, pH, and temperature. Further testing resulted in regression equations expressing CuEC&apos;s of Na and Ca montmorillonites and attapulgite as a function of Cu concentration, pH, and the concentration of metal ions which compete with Cu for exchange sites. Using these equations, an analysis was made of the impact each clay could have on overall copper recovery. The results suggest that Ca and Na montmorillonite clays could have a major impact on Cu recovery and that attapulgite and illite clays could have a smaller, but still significant, impact. Kaolinite and ripidolite clays pose little threat to loss of copper from in situ leaching solutions. Copper losses are decreased by the presence of competing ions, and A1 and Mg have the largest impact of those ions normally present in Cu leaching solutions.

Jan 1, 1993

Early experiences suggested autogenous mills were difficult to operate and consumed substantially more energy than conventional rod/ball mill circuits. As our understanding has increased and the technology has matured this perception has changed to the point where most new comminution circuits are ag/sag based. In addition many operators have replaced existing conventional circuits with this technology. The JKMRC has been studying ag/sag mills for over 20 years. During this time it has amassed what is probably the single largest and most detailed data base of pilot and full scale mill operations in the world. This has been used to help develop and refine its cur- rent commercially available mathematical model of ag/sag mills. A decade of its application has greatly helped simplify both design and operation of ag/sag milling circuits as well as helping to promote the effective use of recycle crushing, secondary crushing and closed-circuit operation. This paper describes the development of ag and sag milling in terms of our understanding and the evolution of the technology. In addition the application of mathematical modelling and simulation in designing and operating efficient circuits is described with the aid of practical examples.

Jan 1, 1998

By Chandra S. Brahma

INTRODUCTION The process of predicting ground condition with exactitude and of ascertaining appropriate ground control measures is pertinent to each and every excavation. The control and support of soil and/ or rock during and subsequent to excavation is essential in order to overcome or avoid excessive movement, maintain stability or preserve integrity of the excavation, handle or prevent excessive water intrusion or hydrostatic pressure build up, and produce an excavation that is safe and suitable for its intended purpose. The design of support systems has primarily been, until recently, based upon experience and empirical or semiempirical guidelines, which do not lend themselves to thorough analytical calculations giving rise to the desired degree of confidence in design of such systems and consequently, several, if not a majority of support systems, no doubt, are overdesigned. The primary objective of this paper is, therefore, to briefly outline engineering considerations leading towards the design of ground control systems for near vertical excavations extending to shallow depths in metamorphic rock formations. Several engineering considerations including the selection of temporary support systems, technical aspects of design, and the sequence as well as details of construction, are briefly outlined. Since excavation for mining purposes or for civil engineering works frequently must pass through highly decomposed, weathered, fractured, sheared or faulted rock masses, the problem of general interest in underground engineering involving analysis of the stability or the support requirement for an excavation in an

Jan 1, 1981

By N. R. Joshi, A. D. Agate

It is estimated that more than 80% of phosphate rock output in the world is used for fertilizer production. In India, there are only a few high-grade deposits of phosphate ores; therefore, most of the requirement for phosphatic fertilizers is satisfied with imported DAP (diamino phosphoric acid). Due to the drain on foreign exchange reserves, this import-dependent, essential commodity is in short supply in India and, therefore, is sparingly used by farmers. In addition, of the added phosphorus, normally 80% becomes unavailable to plants because phosphorus complexes are formed in soil, causing deleterious effects on plants. In our laboratory, this problem was tackled by using a bacterial consortium of phosphorus-solubilizing bacteria. It resulted in the speeding up of seed germination and increasing available phosphorus in the soil by 14%, over a period of 80 days. To use the low-grade deposits of phosphatic rocks available in India near Hirapur, Madhya Pradesh, India, which contain high amounts of iron, beneficiation through microbial means was used for phosphorus removal. Beneficiation was achieved partially through removal of extra iron by oxidizing ferrous iron from the ore by a Thiobacillus species after removal of impurities containing both silica and iron, instead of sieving and cleaning the ore using different techniques. This resulted in a cleaner ore, with nearly 70% of such impurities removed. The factors for beneficiation technique were standardized at the laboratory level and are being used for scaling up of the process. Thus, the beneficiation of phosphatic rock from Hirapur will be an important first step of phosphorus production in India.

Jan 1, 1999