Search Documents

By D. Dimitriadis, T. Polglase, M. M. Botz, W. Phillips, R. Jenny

Cyanidation processes for the extraction of gold or silver frequently involve the processing of sulfurcontaining solids that react with cyanide to form thiocyanate. The formation of thiocyanate is an undesired side reaction, and in many cases thiocyanate formation results in a prohibitively high cyanide consumption. With the increasing number of gold and silver mining projects that involve the processing of sulfide ores or concentrates or that utilize a biological sulfur oxidation process, more attention is being focused on minimizing thiocyanate formation and in treating solutions to eliminate toxicity associated with thiocyanate. Though not yet commercially applied, there are several processes available to recover cyanide from thiocyanate to reduce tailings toxicity and to allow the reuse of cyanide otherwise lost to thiocyanate formation. This paper presents an overview of processes available for recovering cyanide from thiocyanate along with estimated operating costs for the processes. Pilot testing data suggests that in some cases cyanide can be recovered from thiocyanate for approximately the same cost as newly purchased cyanide.

Jan 1, 2002

By Randhir Sehgal

If the primary purpose of a control system is to assure a fixed-quality product at maximum yield, the real issue involved in control of the fine coal cleaning circuit in a plant is to demonstrate that control is technically feasible and economically beneficial . This paper suggests that it is not easy to do so in most cases. Fine coal, defined here as the 28 mesh x 0 fraction of the plant feed, is generally cleaned using a combination of hydrocyclones and flotation. Both of these processes are relatively insensitive to changes in operating variables. Further, the fines fraction general 1 y forms no more than 20% of the plant feed and, at times, is as low as 10%. The instruments to measure flow rates, densities, and product qua1ity (ash, sulfur, etc.) are not sufficiently accurate to allow effective responses to changing state variables and product quality. It is sufficient to run the fine coal circuits at maximum recovery, and the control of product quality and optimization of yield should be achieved by controlling the coarse coal circuits and measuring the quality of the entire clean coal leaving the plant. This contention is made with particular reference to U.S. plants cleaning coal for the utility industry and should be viewed in this context only. It is explicitly admitted that this strategy is mathematically non-optimal in the sense that all size fractions are not necessarily cleaned at equal elementary ash, and would result in a loss of yield. However, under the conditions of conventional coal cleaning practice, this is a sensible approach.

Jan 1, 1988

Diamond wire rock cutting is the most widely used technology in carbonate stone quarrying owing to technical performance and block face quality. Interest is also growing for siliceous deposits. This paper deals with the problem of optimum wire utilization under restrictions regarding a set of variables and parameters. A computer program of general applicability has been set up with the aim of studying the most suitable combination of technologies and the effect on the technical and economic results of bench geometry, overall quarry yield, market -stone value, quarry size as well as the quantity, productivity and price of human and material resources and their organization in the elemental working cycle. Two quarrying problems are considered as significant instances a granite and a travertine quarry. The results are illustrated and discussed.

Jan 1, 1989

By John A. Herbst, William T. Pate

Column flotation is emerging as one of the most important new separation technologies of the decade. Attendant to this development is the need for a quantitative understanding of the dynamic characteristics of columns. An understanding of the many important sub-processes occurring in the cell makes possible the development of dynamic simulators for flotation columns which will aid in the design of control systems for dynamic and steady state optimization. This paper presents a dynamic model for the column flotation cell developed from a population balance point of view similar to that which has been successfully applied to conventional flotation cells. In particular, the mixing that occurs within the pulp is modeled with a distributed-volume, mixer-in-series model as an approximation to the axially dispersed plug flow transport that occurs in the cell. This simpler approach avoids the distributed transport model which often leads to mathematical intractability. Other phenomena dealt with are the attachment and detachment of particles from bubbles in the froth and pulp, the transport of water and the bubble volumes with the froth and pulp phases. Simulation of the flotation of an Illinois No. 6 coal in a pilot plant flotation column were performed to test control strategies.

Jan 1, 1989

By Barbara Maren Winkler

For mine production problems in mines with varying qualities, both open pit and underground, the linear programming method (LP) has been used successfully. By this method it is possible to keep the total production blend for each period within a required range of qualities while optimizing objectives like production costs, net return, ore grades, other qualities, or a combination of these. Technical restrictions like constrained capacities can be added to the model. This makes LP a flexible and powerful tool for mine production planning. Practical experiences have shown the major influence fix costs have on the actual economic result of a planning decision. It can be proven that fix costs cannot be included in LP models. We describe a way to address this fix cost problem by using mixed integer linear programming (MILP) as an extension to LP in the optimization of a mine planning problem. This raises the issue of complexity. We discuss the computational complexity of the resulting models and the enhancement of model flexibility for the user of a planning system. We demonstrate the method embedded in a practicable everyday planning system for a complex underground coal mine. By computational examples we show how the method improves the economical results of the planning.

Jan 1, 1996

By John F. Spisak

Versatile living organisms, historically exploited as functionaries in the food processing, pharmaceutical and chemical industries, have not been successful in achieving similar or significant acceptance within the minerals industry. The current biotechnical revolution coupled with its expanded understanding, dictate that a flagging minerals industry reconsider the use of biotechnology in metallurgical applications. Living resources, either singly, in commensal association or in complex communities, are capable of duplicating fully integrated and complex processing functions. Organisms can mine and extract metals, detoxify chemical effluents and synthetically produce compounds. They have been criticized as exhibiting poor kinetics, excessive energy consumption and environmental sensitivity. However, expanding knowledge reveals that these organisms are surprisingly adaptable, variable and extremely durable. Applied biotechnology in specific cases offers favorable economic returns, environmental benefits and aesthetic value. Selective implementation of living systems can offer opportunities for reduced labor, increased productivity and technological advance. Success will not come easily. Capital must be risked, controversial decisions made and new ground plowed. Traditional, specialist thinkers will of necessity give way to interdisciplinary expertise and unorthodox methodology if success is to be achieved. Those who vigorously persevere, however, are likely to be rewarded with a dynamic and profitable new role in a restructured minerals industry.

Jan 1, 1985

By John E. Urosek, Jack E. Tisdale

The Mine Safety and Health Administration (MSHA) has developed a Mine Ventilation Bleeder and Gob Training Course. This three day course is designed to increase the knowledge and understanding of bleeder ventilation systems. It discusses concepts, designs, plan approval, inspection and evaluation of bleeder systems. This paper will introduce some of the material contained in that course, focusing on the inspection, examination, and evaluation of bleeder systems. The regulations addressing the use of bleeder systems are found in Title 30 Code of Federal Regulations (30 CFR) Section 75.334. The examination requirements are found in 30 CFR Section 75.364. Section 75.364 de- scribes specific locations where examinations are to be made and specific information to be gathered at those locations. The required locations and information will be discussed in some detail with examples and illustrations. These weekly examinations for bleeder systems are designed to monitor the parameters of the bleeder system and to evaluate its effectiveness. Over time, conditions can develop in the bleeder system that affect the ventilation and lead to hazards such as methane accumulations. The hazards of methane accumulations need to be understood as such accumulations can contribute to mine explosions. The importance of additional information gathered by the mine examiner that can assist in evaluating the performance of the system will also be discussed.

Jan 1, 1997

Over the past few years, the School of Mines of Paris has carried out a program of research* on the grade-tonnage relationships in the border zones of porphyry copper deposits. The initial problem was quite difficult : how does the grade vary at the border of the known orebodies? Does it decrease regularly, or do some thresholds exist, where the grade diminishes abruptly? The answer to these questions have important repercussions on the prediction of the future reserves in the fringe of the orebodies. If the grade decreases regularly, very important reserves could exist; if not, there would be strong limitations to the possible recoverable reserves. The first step of our study was a critical study of previous work done on the subject. It appeared that, following Lasky's pioneering paper (Lasky, 1950), most of the authors used what we can call an historical approach to the problem. In this, the grade-tonnage relationships are calculated from the available figures for production and reserves and the results are then extrapolated to the future. The strong limitation of this model are brought out in this article.

Jan 1, 1982

By D. A. Peterson

Laboratory testing was completed to determine the effectiveness of a fiberglass cable bolt (FCB) as a cuttable rock support for a continuous, hard-rock mining method. The FCB consists of four Polystal tendons combined in a node/antinode fashion, with polyvinyl chloride (PVC) spacers forming the anti-nodes. The largest ultimate pull-out load achieved by the FCB was 22 t (48,400 lb) at 89% of the tendons' theoretical pullout load. This premature tendon failure is accredited to: • differential stresses within the tendons and • differential tendon displacement. An increase in pull-out resistance for a given embedment length is due to: • increased bond area, • reduced interfacial shear and • "wedge" effect. The critical embedment length was found to be 40% less than for conventional steel cable bolts (SCB) at a 127-mm (5-in.) node spacing. An FCB can have up to a 92% increase in load-carrying capacity over a conventional SCB at equal embedment lengths. The load carrying capacity is equivalent to SCB at a 960-mm (37.8-in.) embedment length. Though the FCB is 7.5% more expensive than the conventional SCB (installed), this cost may be offset by increased performance. FCBs are a potentially viable support alternative for continuous hard-rock mining.

Jan 1, 1993

By Simon Wright, Roland Heersink

In the past, the center of most companies' e-initiatives has been on reduction of indirect costs, such as selling and procurement. Recently, e-commerce has moved its attention from back-office functions into manufacturing, in order to significantly reduce direct operating costs. This paper describes many of the Web-Powered Manufacturing initiatives being employed across various industries, and relates them to similar opportunities being started within the mining and mineral-processing sector. The following opportunities are enabled by Web-Powered Manufacturing: • Collaboration with outside experts to extend their pool of resources • Management of remote and distributed operations • Tie-in of small operations to a larger operation • Monitoring a position in a JV operated by a partner • Managing a plant located in someone else's facility • Having a chemical supplier manage his inventory in a customer's tanks • Having an equipment supplier remotely troubleshoot his equipment installed in a customer's site • Having an additive supplier provide remote pro-active. guidance in optimization of a customer's operation • Having software suppliers take responsibility for the results of their applications • Outsourcing software and systems support by providing remote access Details of one of these opportunities are described in this article, and the benefits captured using this approach and the technologies necessary to make them a reality are emphasized.

Jan 1, 2002

By Mark S. Stagg, Michael J. Nutting, Douglas R. Barlet

Single-row bench blasts at a reduced scale in the field were used to study the effects of delay time on fragmentation. Nine shots with a spacing of 21 in. and a burden of 15 in. (S/B = 1.4) and nine shots with a spacing of 30 in. and a burden of 15 in. (S/B = 2.0) were completely screened to determine particle size distributions. Delay intervals between holes ranged from 0 to 45 msec, corresponding to effective delay intervals ranging from 0 to 36 msec per foot of burden. Each shot was instrumented with strain and pressure gages to measure in situ blast dynamics and to evaluate interactions between blastholes. Finer overall fragmentation was produced for shots with delay intervals between 1 and 17 msec per foot of burden. Only for shots within this optimum delay range was it observed that the strains induced by stress waves constructively interacted with strains induced by gas pres- sure from an earlier detonated hole. Coarsest fragmentation resulted at delay intervals less than 1 msec/ft, where stress waves from each hole were observed to interact destructively, and at delay intervals greater than 24 msec/ft, where no inter- action between holes was observed, indicating a condition that can be considered as the firing of single hole shots independently.

Jan 1, 1986

By K. S. E. Forssberg, S. Subramanian, Hanumantha K. Rao

The dispersion characteristics of apatite and magnetite minerals have been assessed based on zeta-potential measurements, using various inorganic and organic reagents, namely sodium silicate, sodium tripolyphosphate, sodium hexametaphosphate and lignin sulphonate. These results highlight that apatite is dispersed to a greater extent vis-à-vis magnetite. Further, the dispersion efficiency of the phosphate reagents is better than that of sodium silicate or lignin sulphonate, for both apatite and magnetite. Batch flotation tests on a high phosphate magnetite ore from Kiruna indicate that higher apatite recovery with minimum phosphorous loss to the magnetite fraction can be achieved using sodium silicate as a dispersant. Although comparable dephosphorization can be attained with lignin sulphonate dispersant, the recovery of magnetite in the non-float fraction is lower, possibly due to the adverse synergistic effect of this organic reagent with the Atrac collector, resulting in the flotation of magnetite. The high intensity conditioning of pulp for up to 30 min resulted in better apatite flotation with <0.015% phosphorous in the magnetite product.

Jan 1, 2002

By M. J. Shulman

The exploration geologist is frequently confronted with the problem of allocating his resources, i.e., exploration effort, among various areas. Although geologic, financial, and logistic considerations influence the allocations, no objective criterion is usually given that determines the optimal allocation. Maximizing the expected gain in information, subject to the constraint of a limited exploration budget, is used as the objective criterion to allocate airborne reconnaissance effort. The information function, I(x), quantifies the expected gain in information, where x is the scale of exploration. To calculate the information function, the following probabilities are required: the probability that an area contains a deposit; the probability that an anomaly is produced by the target; and the probability that an anomaly is produced by a barren area (false signal). Alternatively, the barren areas can be replaced by other targets. To illustrate the allocation method, the optimal number of line kilometers, i.e., the optimal line spacing per area, is determined for an aeromagnetic survey for iron in Egypt.

Jan 1, 1987

By Michael E. Kelahan, Charles Y. Guan, Glenn A. Gruber

A comparison of the IMC Anionic Process and the CLDRI Process, based on pilot plant testing of waste pebble by Jacobs Engineering is presented. Estimated costs for constructing and operating a beneficiation plant utilizing dolomite flotation are given. Research to develop practical flotation processes for removing dolomite from low-grade phosphate rock has been a high priority for the Florida Institute of Phosphate Research. The Institute funded the above pilot plant programs in 1998 and 2000. The Florida Phosphate industry currently deals with the increasing dolomite content of ore reserves by practicing selective mining. Heavy media separation plants installed at two mines to remove dolomite from pebble are not being operated. The flotation separation of dolomite from waste pebble requires that the flotation feed be ground. Grinding liberates the mineral species and produces particle sizes small enough to be floated. Only two dolomite flotation processes, the IMC Anionic Process and the CLDRI Process, have been successfully demonstrated on flotation feed that has not been deslimed after grinding. Deslimed flotation feed, relative to undeslimed feed, has improved flotation performance and reduced reagent consumption. However, for the above mention processes, undeslimed ground feed increases the yield of concentrate because the phosphate desliming losses are avoided.

Jan 1, 2002

By J. M. Dean, R. L. Grayson, N. P. Reddy, Y. J. Wang

This 1988 survey provided a cross section of computer software use by the US coal industry. From 1250 mailed questionnaires, 171 responses were received, representing a 4.9% sampling of the 3496 US coal mines. Since the distribution of responses by regional stratum matched well with the distribution of mines by stratum, the survey was given statistical validity. A statistical description details the computer use by region, mining type, organizational size, the level of application within the organization, the type of software application used, the variety of computers on which the software was used and the percent of users within engineering, management and general applications categories. Overall, 63.5% of the respondents use computers at some level in their organizations. All of the mines producing more than 454 kt/a (500,000 stpy) used computers. However, for those producing more than 9 kt/a (10,000 stpy) but less than 91 kt/a (100,000stpy), only 44% used computers. Generally, the software applications were still data-processing oriented. The application sophistication grew with increasing mine size. Computer system models and configurations for different sized organizations are recommended based on the configurations used in the industry at the time of the survey.

Jan 1, 1994

By S. Majumder

The longwall face supports are provided to prevent the caving of the immediate roof at the working face. The thickmess of the immediate roof may be obtained from the working height and the average bulking factor. A strong bed, capable of withstanding maximum bending moment among the beds within the above roof, can be identified. The load on the strong bed may be obtained by finding out the overlying beds that will rest on the former during sagging. The limiting span, L, for this unsupported loaded bed, as a beam with built-in ends, can be calculated. The support density required at the supported span (face to goaf edge), a, during the first fall, is now estimated with a view to have a safety factor 2 at the face end, when bending failure occurs at the barrier end. However, the above value is inadequate to provide necessary safety margin against bending failure at the face end, during the subsequent cavings as cantilever, for L/a less than 20.6. d For the latter case a separate expression is derived.

Jan 1, 1986

During the past decade, international mining companies have descended on South America. Countries like Chile, Brazil and Peru have seen billions of dollars in exploration and development funding turn their once meager mineral industries into mining giants that have become the envy of the world. Part of this outpouring of foreign investment in those countries has been because each has privatized its state-owned mining companies and has liberalized its foreign investment laws. In addition, they have rewritten their mining codes to encourage minerals development and passed new tax laws that have made natural resource development more attractive. Now these same international mining companies are turning their attention to Argentina. This a country that, like Chile, Brazil and Peru, has a wealth of largely un- tapped mineral resources. And Argentina wants its share of the foreign investment that its neighbors have enjoyed. With that in mind, ministers of Argentina&apos;s natural resource agencies came to Denver, CO to meet with mining executives and pitch their country&apos;s mining industry. The meeting, attended by about 200 people, was sponsored by the US Trade and Development Agency and organized by the World Trade Center Denver. Others involved were the Colorado Mining Association, the Colorado International Trade Office and the Secretariat of Industry, Commerce and Mining of Argentina. The following is a summary of a report on Argentina&apos;s mining industry. It was prepared by Anderson & Schwab Management Consultants and distributed to attendees as part of the meeting&apos;s program.

Jan 1, 1998

By John A. L. Dr. Campbell, James W. Haskew, F. Hoy Lee, Elliott P. Dr. Doane

Emissions of particulates, unburned hydrocarbons, nitrogen oxides (NO[ ]) and carbon monoxide (CO) from diesel engines are of concern in mines, particularly underground mines. All these undesirable products except NOx are the result of incomplete combustion in the cylinders. Various approaches to achieving more complete combustion in diesel engines have included different fuel compositions, use of catalysts, fuel additives, engine modifications, and oxygen-enriched intake air. The present study shows that injecting minute quantities of primarily platinum group metal catalysts into the intake air of a Deutz/MWM D916-6 mine diesel engine substantially reduces emissions in the exhaust. The catalyst injection system, which was developed by National Fuelsaver Corporation (Robin. 1981), transfers catalyst compounds in solution to a stream of air bubbles by a process called Bubble Fractionation (Lemlich et al.. 1966, 1968. 1970). The amounts are so minute that concentrations in the engine exhaust should be well below OSHA/NIOSH Time Weighted Average (TWA) exposure limits at steady state, a fact that was confirmed by analysis of collected particulates in the exhaust. When the catalyst injection was used along with a pleated paper filter to remove exhaust particulates, the filter operating life was shortened greatly. Therefore, this system is not recommended for use on diesel engines equipped with a water scrubber and a filter. It does offer a practical and relatively economical way of reducing exhaust emissions from other diesel engines, such as those in outby mine service

Jan 1, 1995

By Richard Meriwether Smith

Mining-related earthy bodies in contact with the atmosphere are now counted, generally, as minesoils. Because soils within this broad category are extremely young the influence of parent material is stronger than in older soils, where climate, organisms, and topography have had time to interact with near-surface rocks to form more distinctly differentiated profiles. Understanding of minesoil properties and processes is aided by definitions of rock types in terms of chemical, physical, and mineralogical characteristics that are, with some degree of consistency, translatable into soils. Geological correlations based on age or sedimentary sequences are helpful if they assure details of mineralogy and lithology, but our pedologic objectives demand that any conflicts involving rock types must be resolved in favor of distinctions having strongest implications for soil properties after mining. Chemically this approach emphasizes accounting of potential acid-base status, plant nutrient availability by adapted and calibrated extraction procedures, and absence of biotoxins. Physically it anticipates particle sizes, shapes, and arrangements in readily pervious soil profiles that will favor plant growth with desired levels of moisture and oxygen. Concurrently we are considering soil property suitability for uses other than growth of plants. Above all we need to be able to predict pedogenic processes in the particular environment, including rate as well as direction of chemical and physical change.

Jan 1, 1974

Jurist, educator and historian Neil Reynolds will be the keynote speaker at the National Mining Hall of Fame&apos;s 11th annual induction banquet on Sunday, Oct. 11,1998 at the Pointe Hilton Resort in Phoenix, AZ. Reynolds is Municipal Court Judge for the City of Leadville, CO, home of the National Mining Hall of Fame & Museum, and a fifth-generation resident of the community. His family staked mining claims on nearby Mount Massive in 1862. Judge Reynolds is a fulltime faculty member at Colorado Mountain College, Chairman of the Lake County Historic Preservation Advisory Board and practices law in Leadville. In announcing the speaker, Board Chairman Richard Moolick said seven inductees into the National Mining Hall of Fame will join 138 mining greats previously honored in the annual ceremonies. This year&apos;s inductees will be enshrined by Thomas Falkie, president and chief executive officer of Berwind Natural Resources of Philadelphia, PA. Moolick also announced that Jeffrey Clevenger will be the master of ceremonies for the induction banquet. Clevenger is executive vice president of Cyprus Amax Minerals, Englewood, CO and president of Cyprus Climax Metals, Tempe, AZ. A cocktail reception at 6:30 p.m. will precede the black-tie (optional) dinner, to begin at 7:30 p.m. For additional information, contact Esther Mellott at 719 486 1229. Here are the biographies, then, of this year&apos;s seven inductees to the National Mining Hall of Fame & Museum.

Jan 1, 1998