Search Documents

By Eckl, Martin, Stefan Lemke, Martin Londschien

"Tunnels are built with a design life expectancy of over 100 years. One key component of such a design is the waterproofing system, which must reliably fulfil its function during the whole service lifetime of the tunnel structure. This paper deals with the determination of test criteria for the durability assessment of geosynthetic products in tunnel sealing systems. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa. To verify the results of the new test procedure the material properties of geosynthetic products samples removed from older tunnels are investigated. Based on the presented results of the still ongoing research programs some preliminary conclusion regarding the updating of regulations for tunnel sealing systems are given. INTRODUCTION Watertightness is directly related to the durability and serviceability of the concrete lining. Therefore, modern traffic tunnels and shafts (Figure 1) are generally protected against mountain/ground water and water penetrating through rock fissures by a sealing system, for example with a loose-laid polymeric sheet membrane. Hereby the waterproofing sealing systems must be reliably fulfilling their function during the whole service life of the tunnel structure, regularly of more than 100 years. In consequence, the quality and lifetime performance of the waterproofing materials—beside the correct professional and careful installation in a tunnel infrastructure, is of great importance. The challenge for the industry, owners, operators and designers is ultimately the development of qualification testing and requirements (acceptance criteria) for products to ensure the design lifetime performance. Hereby the qualification procedure is seen as a routine integrated in standards, norms or guidelines, wherein test procedures should cover typical environments for the specific application fields. Polymeric synthetic raw materials are increasingly used in products with long service lifetimes (e.g. in injections, gaskets, waterbars, spray-applied and sheet waterproofing membranes). During service they are subjected to chemical (e.g. oxidation processes) and physical (e.g. changes in morphology) influences from the environment, which affect their mechanical properties—and they age. Hereby organic materials are more affected than inorganic materials. Also, polymers show strongly temperature-dependent properties compared with other construction materials. However, their long-term aging behavior is not given per se and has to be explored extensively by suitable tests, which simulate—under accelerated processes—real exposures and loads. Hereby the understanding of the individual aging processes is crucial along with the long-term experience with these materials to ensure the transfer of the laboratory results and performance to site practice (test calibration) and vice versa."

Jan 1, 2016

By W. Burger

For the development of deep hard rock mines fast access to the orebody is critical. In some cases the mineralized area is more than 1500 m (5000 ft) below surface. Excavation of shafts or declines is typically on the critical path of the project schedule. Saving time on those activities can significantly increase the net present value of the mining project. Mechanical excavation methods are a step-change in excavation performance and labor safety compared to drill and blast operations. In hard rock conditions roadheaders can not be used effectively, so disc cutting is the first choice. For excavation of declines tunnel boring machines (TBM) can be used in many cases. These provide in certain rock conditions considerably higher production rates compared to drill and blast excavation.

Jan 1, 2010

By J. R. Palmes

Three coal samples, selected out of eight with well characterized surface properties, were used in flocculation tests and synthetic mixture of coal and silica was used in the selective flocculation experiments. Coal wettability and flocculant type were found to have a strong effect on the flocculation results.

Jan 1, 1993

By Thierry Coléou

In this paper, we consider open pit optimization. At present, most methods specify the economic parameters and then find the corresponding optimal pit. But as the economic environment varies (which it does regularly these days), the "optimal" pit changes and quite often changes markedly. The questions are: by how much does it change and which parameters are most influential? The functional approach of Technical Parameterization of Reserves, devised by Matheron in 1975, gives the set of all the different optimal pits, under any economic condition. It separates technical design and economic assumptions and thus permits the use of several optimality criteria when choosing the final pit, and not just the maximization of an additive profit formula. Very efficient specific algorithms are presented to obtain all the potentially optimal pits. Fluctuations in the parameters induce changes in the optimum design. Inclusion relations that exist generate very tight bounds and hence very quickly detect optima, even when using a classical adaptation of maximization techniques (graph theory, moving cone, dynamic programming ...). The advantage of Technical Parameterization of Reserves over other methods is that it provides a nested sequence of optimal pits which can then be used for mine scheduling. Many possible mining schedules can be obtained by using the family of technically optimal projects to split up the orebody. The "optimal" schedule, which is in fact a compromise between the different requirements of the economists, the mine planner and the metallurgist, can be chosen from within the wide scope of possibilities. A practical example of mine scheduling for a chromite mine is presented in detail.

Jan 1, 1989

By Paul C. Miclea, Robert E. Murphy

The behavior of fire and airflows in a confined tunnel differ significantly from more familiar fire situations outside, due to the buoyant effect which tends to create a layer of hot smoke and gases flowing away from the fire near the crown of the tunnel, while air supporting combustion moves toward the fire beneath the smoke layer. A subway emergency ventilation system is designed to force air to flow through the tunnel, shifting the balance of heated air in the direction of the forced flow and avoiding the "back-layering" of hot gases and fumes. This paper presents a computer program, called the "Subway Environment Simulation" (SES), which can be used to predict airflows created by the emergency ventilation system. It utilizes the latest state-of-the-art analytical treatment of fires in enclosed spaces, including observations from mine fires and gas explosions. The program allows designers to reduce construction cost by identifying unnecessary ventilation shafts and by verifying fan capacities. In addition, the program allows the designers and operators to determine safe evacuation routes, in case of a train fire, by predicting the occurrence of back-layering. It can be used to determine when the ventilation system can control the direction of smoke movement to provide a clear and safe path for evacuating people and facilitate fire fighting operations.

Jan 1, 1989

By Robert C. Freas

Over the past twenty years people throughout the world, but particularly in the United States, have been taking an increasing interest in the environment, sources and causes of pollution, and pollution abatement. Air quality in the United States has been and continues to be an area of primary emphasis. In 1970, the US Congress passed the Clean Air Act and subsequently revised and strengthened it in 1977 with the issuance of the New Source Performance Standards. The Act has been further strengthened with the passage of the 1990 Amendments. By far the largest single source of sulfur dioxide (SO,) pollutants are coal fued electric generating power stations. Hence, a substantial portion of the flue gas desulfurization (FGD) research and equipment installation has been geared to the utility industry. Several competing FGD technologies were touted during the period 1970 to 1990 with varying degrees of success. Subsequently, the more successful technologies have been accepted, revised, and improved to the point that by 1991 third and fourth generation technology is available. A second area of emphasis for FGD has been coal fired industrial boilers. While individually they are much smaller than any electric utility generating station, they do represent a significant source of sulfur pollution. However, due to the size of industrial boilers and their location within industrial and educational complexes, the wet scrubber technology being employed by the utilities is not appropriate for these applications. Hence, fluidized bed combustion (FBC) technology has been developed for the industrial boilers. Since the installation of the first full scale test unit at Georgetown University, several equipment vendors have come forward with an increasing array of more sophisticated FBC units. Currently, FBC technology has matured to the point that the Tennessee Valley Authority (TVA), in cooperation with the Electric Power Research Institute (EPRI), has installed an FBC system on a 250 MW test unit at the Shawnee Power Station in Kentucky.

Jan 1, 1994

By Milton F. Searl

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technlogy are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 1, 1980

By Searl. Milton F.

Introduction The urgency of further development of our domestic energy resources becomes more apparent every day. The production capability of existing facilities, taken in the aggregate, declines perhaps 10% per year; imported energy is expensive if available at all; conservation helps reduce demand but eventually will reach a point of diminishing return; new energy sources are promising but past experience, as with nuclear power, teaches us lead times are long and success is not assured. To approach the energy future rationally, it is essential to have some idea of the size of the nation's remaining energy resources, their characteristics, and the degree of uncertainty involved in their estimates. Resources are, of course, only one end of a long chain leading to energy supply to the ultimate consumer. They are an essential element, however, and the only one not under society's control. Given that the resources and a national will to produce the energy exist, it is possible to convert the resources to supply in, generally, an environmentally reasonable manner. However, the process of developing supply takes time. Government must permit access to the resource, and remunerative prices and further evolution of technology are required. This paper does not deal with these essentials, but they must not be forgotten. This discussion is limited to coal, oil, natural gas and gas liquids, uranium, and oil shale. Other energy sources are discussed elsewhere in this issue. Crude Oil Conventional crude oil resources are of greatest concern today, given our dependence on imported oil and its rapidly rising price. Estimates of oil originally in place (OOIP) range from 619 billion bbl to 1,094 billion bbl, differing by almost a factor of two (Table 1). This is surprising because the U.S. is a mature petroleum province with over 120 billion bbl produced and over 400 billion bbl OOIP discovered. Differences in the estimates involve differences in the experience of the various estimators, the interpretation of present geologic information and historical statistics, the methodology, and probably the extent (i.e., water depths) for which offshore resources are included. The range shown for the estimate of a given estimator appears to be primarily due to geologic uncertainty. This uncertainty can be measured by taking the ratio of the low and of the high estimate to the expected estimate for that information source. The low estimates range from 0.85 to 0.87 of their respective values. The high estimates range from 1.18 to 1.27 of the expected values. In all cases the high estimate is further from the expected value than the low,

Jan 9, 1980

By Anders Sellgren, K. Hansson, A. Jedborn

In the mining industry, conversion of fine particles into a slurry is often part of the normal processing of the ore. Therefore. from a system's point of view, slurry transportation would be considered as a natural alternative, all the way from the working face to the final processing. In underground mines, there is sometimes a considerable inflow of ground water that has to be pumped out. When the mine dewatering installations are integrated with a hydraulic hoisting system, the cost of power needed to pump out the ground water can be excluded from the cost of hoisting, compared with other modes of transporting the solids to the surface. The chief advantage of hydraulic hoisting is that the hoisting capacity can be increased at comparatively low total cost without necessitating the sinking of new shafts. Alternative examples include deepening of the existing mechanical hoisting system, truck, or conveyor belts transport in ramps to the present level. These often become very expensive. The economic effectiveness of hydraulic hoisting and hydraulic design considerations have been discussed by Kostuik (1965) and Sellgren (1985, 1986) for both small shallow mines and large deep underground mines. Objective and scope The objective of this study was to demonstrate the feasibiliy of hydraulic hoisting in hypothetical examples of mine deepening. Underground grinding to a maximum particle size of about 700 um (about 25 mesh) is considered. The pumping of ground ore products with positive displacement plunger or membrane type of pumps at working pressures of up to 15 MPa (2200 psi) is a thoroughly tested technique (Venton, 1986). Hydraulic hoisting system A hydraulic hoisting system is described schematically in Fig. 1. The ore is mined, handled, and crushed conventionally. It is then ground wet underground. The slurry is then temporarily stored in an agitated tank and pumped to an agitated receiving tank on the surface. The ore is then further processed in the concentrator. The capacity of a pipeline is very high. For example, an annual production of 500 Kt (550,000 st) of ore can be handled in a 100-mm-diam (4-in.-diam) pipeline. Systems layout - economic effectiveness Schematic mine layouts are presented that represent situations where hydraulic hoisting often is the most economical alternative. A situation where the ore is trucked to the level of the existing hoisting system is shown in Fig. 2 (following page). With hydraulic hoisting, only a shaft for ventilation, pipe- line, and personnel are needed. In a first phase (Fig. 2). a hydraulic hoisting installation with crushing and grinding units, storage facilities, and pumps has been located at a level of about 400 to 600 m (1310 to 1970 ft) below the surface. With further development of the mine, the hydraulic hoisting

Jan 1, 1990

By K. C. Carriere

INTRODUCTION The purpose of this paper is to introduce the reader to basic control strategies for solid/liquid separation in mineral processing and to indicate some of the implementation difficulties to be encountered, without becoming overly involved in details of process, equipment or software. It is assumed that the reader has some familiarity with control systems and with dewatering processes, since exploration of these topics would require considerably more length. The paper is organized into three parts: first a general discussion on the need for control of dewatering processes and of the general criteria involved, next a more detailed elaboration on control strategies for the various unit operations, and finally a case study showing a specific approach towards such a project. Motivation & Objectives The justification for implementing any control system in an industrial plant is to improve operations and thereby to increase profitability. Without this motivation, the system will likely be perceived as unnecessary and will decline into disuse, an expensive and troublesome monument to someone's ill-conceived ideas. However, when a control strategy is correctly conceived, implemented and integrated into operations, it can provide significant advantages in operating ease and efficiency, and a handsome return on investment. In general terms, the objectives in establishing a control system are: • stabilization of process disturbances maintenance of product quality • maximization of throughput • dearer definition of process • protection of personnel and equipment A successful control strategy must address at least some of the above criteria. However, the most important requirement is a commitment on the part of plant personnel and management to start up, operate and maintain the system, and to upgrade it to reflect current process status and operational philosophy. Process Applications In this paper, control strategies will be explored for the most common methods of dewatering of mineral pulps. These unit operations include: drying, centrifuging, filtering and sedimentation. While the first three are important, they do not tend to be as complex as sedimentation, and thus will not be as exhaustively treated. Sedimentation is very widely applied, not

Jan 1, 1986

By Dirk Bleazard

Barrick Goldstrike Mines is improving the reliability of mining and processing equipment through the use of failure analysis and condition monitoring activities. Program results include an increase in equipment capacity and an overall reduction in operating costs. Identifying equipment failure modes and developing associated capital asset management practices can minimize failure consequences. Successful programs have included alterations to management practices, equipment modifications, and/or the implementation of condition monitoring programs. By controlling or minimizing the effects of incipient equipment failures, corrective actions can be taken earlier in the failure cycle. This results in an associated reduction to repair costs and equipment down time. Mining companies invest in their capital assets to provide the capacity necessary to meet operational needs. Over time, functional failures occur that reduce this productive capacity. Diagnostic technologies now exist that allow the condition of equipment to be monitored. Early response to this information minimizes the effects of functional failures and restores equipment re- liability. Reliability is a performance indicator of overall equipment condition. It is most often expressed in terms of mean time between failures. When the established objectives of a capital asset management program include the maximization of this failure interval, trailing indicators, such as availability and operating cost improve. The probability of equipment failure is influenced by engineering design and operating conditions. The performance level resulting from this operating environment is expressed as "inherent reliability." Without maintenance intervention, equipment will ultimately fail to perform its intended function and become less reliable. Therefore, maintenance must be managed as the supplier of reliable operational capacity. Maintenance can only supply equipment performance that approaches the level of inherent reliability. Actually achieving inherent reliability requires that all maintenance decisions are made at the economically optimal time. Enhancing performance levels beyond inherent reliability can only be achieved by altering operating conditions or practices or through physical equipment modifications. An evolution in maintenance management philosophy has been under way since the beginning of the industrial revolution. As equipment has become more sophisticated, so have maintenance practices. At the beginning of the industrial age, equipment tended to be over designed and slow moving. The first maintenance philosophy was one of reactive maintenance. Maintenance intervals were dictated by the operational status of the equipment. As a result, production interruptions were common and capacity needs were met through an investment in redundant capital assets.

Jan 1, 1998

By John W. Scott

INTRODUCTION The design criteria for a particular concentration and dewatering project will provide the formal basis for design of the process, equipment and facilities. These criteria will specify the required capacities and operating schedules for the equipment, as well as the quantity and quality of the feed to be processed and products obtained. The general climatic and geographical conditions at the site, specific information on soil or rock conditions; and applicable design standards and codes will also be included. The design criteria will generally be based on an interpretation of testwork carried out on the particular ore and site, and will thus parallel in detail and completeness this testwork. As the project moves from the early conceptual phases through to final detailed design, the design criteria will be developed and become more detailed as information is generated and made available for use. The design criteria are critical to the design effort as the formal specification to the designer of what and how much is to be processed, what and how much is to be produced, and where and under what conditions. The actual design criteria will be a formal tabulation of the design basis information developed for the project in question. For a preliminary study, this may consist of a single page of data; for a feasibility study several pages and for a detailed design up to several hundred pages and multiple volumes. Depending on the complexity of the process and the level of detail included, each project will be unique to some degree. The design process for a project normally progresses from preliminary conceptual phases through to a final detailed design. The criteria used for the initial concepts are generally developed from rough data and preliminary testwork on the ore in question. Regardless, the plant throughput and products are defined, thus giving a scope and definition to the study phase. In some studies a range of throughputs may be analyzed in order to arrive at the most economically attractive size for the proposed operation. This optimum size is then used as the design throughput for the more detailed design phases. Similarly as more testwork results are available and the ore characteristics and process become more well defined a continuous updating of the design criteria is undertaken.

Jan 1, 1986

By H. S. Kibler, A. E. J. Gallagher, J. J. Sebesta

A review will be made of the nature, value, costs, and factors associated with industrial minerals production in general. Comparisons will also be made between some of these data and similar criteria for metallic mineral production.

Jan 1, 1987

By Ralph J. Holmes

INTRODUCTION Although sampling techniques used by the mineral industry continue to improve, sampling is still an area which is often neglected. Frequently, sampling and sample preparation requirements are left to personnel who do not fully appreciate the significance and importance of sampling. Consequently, plant evaluations are often based on seriously biased samples, leading to mass balance problems and incorrect assessments of plant performance. The basic rule for correct sampling is that each particle of ore or concentrate must have an equal probability of being collected and becoming part of the final sample for analysis. If this is not the case, bias is easily introduced and the sample is not representative. For example, when ore is travelling on a conveyor belt, the lumps may come to the surface. Consequently, a grab sample taken from the top layers only will contain a greater proportion of lumps, i.e., the sample is biased. There seems little point in making major investments in precise analytical equipment, if the sample provided to the analytical laboratory is not representative in the first place. This paper describes the sources of plant sampling errors, reviews the methods of estimating their variance, presents some worked examples, and provides some practical advice for reducing sampling errors and their variance. SAMPLING BASICS It is generally accepted that the discharge point of an ore or concentrate stream is the most suitable sampling location. The stream can be intersected at regular intervals, and representative samples, referred to as increments, can be obtained by taking a complete cross-section of the ore stream. On the other hand, sampling devices that take part of the stream on an intermittent or continuous basis, e.g., a bleed from a pipe, may introduce serious bias, and should be avoided at all cost. Increments may be taken at completely random times or tonnages during the sampling operation, in which case it is called "random sampling". However, as shown below, random sampling results in the largest sampling variance, so it is preferable to divide the ore or concentrate stream up into strata of equal time or mass and take one increment from each stratum. This operation is called stratified sampling and may be either systematic sampling, in which increments are taken at the same point in each stratum, or stratified random sampling in which the increments are taken at random within each stratum. Systematic sampling results in the smallest sampling variance, provided periodic variations in quality or quantity are not present which may coincide with, or approximate to, any multiples of the proposed sampling interval. In such cases, it is strongly recommended that stratified random sampling within fixed time or mass intervals be carried out.

Jan 1, 1991

By Douglas Owen

Two case studies describe the introduction of technology new to an organisation. The lessons learnt from these Case studies contribute to Our general understanding of the management of technological change.

Jan 1, 1989

By I. Toromanoff, F. Habashi

The transformation of a low-grade titanium slag into synthetic rutile or synthetic anatase can be enhanced by attrition grinding.

Jan 1, 1987

By J. F. Ziegler

The Silver Chert jasperoid, Mercur District, Utah, records a complex history or silicification and tectonic activity.

Jan 1, 1990

By R. Gray

"Experience from Australia has identified what is referred to as non-conventional surface subsidence behaviour. This occurs under irregular surface topography, resulting in valley closure, valley floor uplift or “upsidence”, and far-field horizontal movements – even occurring beyond conventional “angle of draw” limits. This paper discusses such behaviour recently observed in Pennsylvania and focuses on the 2005 case of Duke Lake Dam in Ryerson Station State Park. In July 2005, there was a significant increase in water leakage through a number of growing cracks in the dam leading to the dam being breached to avoid an uncontrolled failure. An underground longwall mine was located approximately 900ft to the north, mining at depths of 330 – 720ft. Investigations (including a subsequent ground movement monitoring program) found a range of evidence in the vicinity suggesting that valley closure and far-field horizontal movements may have occurred resulting from the adjacent mining. The paper discusses the phenomenon of non-conventional subsidence behaviour and the Ryerson State Park case study, including an assessment of mining, geology and subsidence impacts and suggested ground behavioural mechanisms. INTRODUCTION Non-Conventional Subsidence The conventional understanding of coal mine subsidence on which most current subsidence understanding and prediction techniques are based, includes the concept of angle of draw which effectively limits the lateral extent of subsidence effects and impacts. Within this zone – above and marginally beyond the boundary of mining – downward vertical subsidence is the dominant component, together with localised horizontal movements towards the mined region, with related tilts and strains. However, more recent experience from Australia over the last two or three decades has identified what is referred to as non-conventional surface subsidence behaviour. This is found to occur in areas of irregular surface topography or variable terrain, and is characterised by phenomena such as valley closure, valley floor uplift or upsidence, and far-field horizontal movements, all of which can occur beyond the conventional angle of draw limits. NSW Department of Planning (2008) defined the conditions for both conventional and non-conventional subsidence behaviour as follows: “The conventional or general model of surface subsidence, which finds worldwide acceptance, is based on assuming the following site conditions:"

Jan 1, 2015

By Dr. -Ing. Karlheinz Timtner

This paper deals with the complicated and often misunderstood relationship between torsional windup, load sharing and peak torques in conveyor backstops. The principals apply in low speed, intermediate speed or high speed applications. Once the controlling factors are understood, a reasonable approach to selection procedures can be achieved.

Jan 1, 1996

By Bruno Paponetti, Luigi Toro, Carlo Abbruzzese, Maria Y. Duarte, Anna Marabini

A bioleaching process has been developed to extract manganese from low grade domestic resources not amenable to conventional mineral processing operations. Between the different strains of microrganisms tested, Thiobacillus ferrooxidans has appeared poor over manganese, Aspergillus niger allowed to obtain high recovery, probably due to the metabolic production of citric and oxalic acids, showing a remarkable complexing and reducing action. The growth of microflora has been correlated to the MnO dissolution as confirmed by SEM observation.

Jan 1, 1989