Search Documents

By W. R. Bush

Radiation protection in uranium mines and nuclear reactors is compared, with the objective of determining if any radiation protection practices which have worked well in one area can be adapted to the other area, especially from reactors to mines since radiation protection is more highly developed in reactors. Several areas are identified where improvements can be made in radiation protection in mines, the most important being improvement in ventilation at the workplace, greater attention to special monitoring during upset conditions, and a need for a substantial increase in radiation protection staff. It is concluded that, although considerable room exists for improvement, the general approach to radiation protection presently being followed seems appropriate for the circumstances encountered in mining.

Jan 1, 1981

By R. L. Lewis

A simple method for estimating the steady-state water quality of a pit lake is presented. The steady-state concentration of a conservative chemical constituent in a pit lake is shown to be a simple function of the inflow rate, the evaporation rate and the inflow concentration. An analytical method is presented for estimating the equilibrium ground water-inflow rate for use in water-quality predictions. The time required to reach chemical steady state is estimated using an iterative mass-balance model. Mine operators should find the methodology useful for planning and screening regulatory applications where conservative estimates of pit lake water quality are desirable.

Jan 1, 2000

By W. Nahas, T. C. Watson, A. R. Maycock

The development of roasting technology for the oxidation of sulfides in refractory gold ores is discussed. Case studies covering operations dating from the mid-1930's to the present day are used to illustrate this development. The roasting of ores and concentrates is reviewed and various gas cleaning flowsheets are discussed with particular reference to environmental requirements. A sequence chart is provided to show the development path of a potential roasting project.

Jan 1, 1990

By S. K. Kawatra, T. C. Eisele

A horizontal-baffle arrangement has been developed to prevent excessive axial mixing in flotation columns. These baffles have been shown in previous work to improve the grade/recovery performance of both a laboratory-scale column and a pilot-scale column (Kawatra and Eisele. 1993). In this paper, results are given for continuous on-line operation of the pilot-scale baffled column in a commercial coal- cleaning plant. These results show its ability to operate for extended periods without plugging, to produce a consistent-quality product even while the feed quality was fluctuating, and to remove much of the pyritic sulfur from the coal.

Jan 1, 1995

By C. R. Euston, B. T. Field, W. E. Lindquist

Pyroprocessing applications in the minerals industry range from low-temperature drying to high-temperature reactions. Material characteristics and process requirements range over a very broad spectrum and can confuse plant engineers trying to select a pyroprocessirtg system for their plant. This paper examines the important process variables and offers empirical guidelines to assist in a user's overall process evaluation.

Jan 1, 2000

By Donald Lau, Adrian Crawford

In the field of grouting, practitioners fre¬quently advocate procedures that are often unique and contradictory. As a result there has been considerable debate as to what constitutes optimum grouting practice. A knowledge of both the rheological properties and the flow characteristics of grouts is essential to the development of a rational understanding of the grouting process. Flow models and viscosity experiments have been conducted using cement grouts comprising High Early Strength Portland and Microfine cements. The addition of superplasticizers was found to enhance the flowability of the grouts as well as to reduce the effective groutability ratio. Steady state flow equations and design charts for predicting the radial penetration of cement grouts have been developed.

Jan 1, 1986

By M. J. Meulendyke, J. D. Purdue

Within the mineral processing industry, a range of grinding conditions exists which include semiautogenous grinding (SAG),rod milling, and conventional ball milling. Each of these mill environments presents a unique environment for grinding media, requiring the application of specific physical and chemical properties for optimum grinding media performance. The environments are characterized by varying degrees and combinations of abrasive, corrosive, and impact wear. An extensive test program has been conducted to determine the extent wear rates vary between these different applications. Test results are related to production results, ball size, and mill operating conditions.

Jan 1, 1990

By G. Johnston, P. K. Chatterjee, S. Holguin

Underground mine planning is largely manual and can demand considerable resources to generate a working plan and to perform limited tests of sensitivity to variations in geological and mining conditions. It is possible to use computer aided mine planning to automate many of the manual procedures to allow the planner to evaluate a number of layouts, extraction strategies, and schedules. his paper examines the simulation and scheduling of an under- ground coal mine operation through the-use of on- screen graphics. The simulation will provide a basis for predicting productivity and other relevant information over a specified number of shifts. The software developed is extremely user friendly and reduces the tedium of repetitive manual calculations inherent to mine planning and drafting to a minimum, thus offering considerable savings in an area that is widely recognized as extremely labor intensive.

Jan 1, 1988

By Paul M. Godlewski, Gerry Millar, Harvey W. Parker

Recently, over 70 railroad tunnels in the western USA have been enlarged and rehabilitated "live track," utilizing modern excavation and lining methods, in most cases to clear the larger double-stack container cars. This paper presents the general conditions of the tunnels and the technical aspects and costs of the rehabilitation of approximately 40 kilometers of tunnels, which range in length from a few hundred meters to 13 kilometers. Concrete-lined tunnels were rehabilitated by grouting and rock bolting, while unlined or timber-supported tunnels were relined with shotcrete and rock bolts. High output lining methods were required because of limited track time. Enlargement has been accomplished primarily by carving notches out of the concrete linings with a roadheader, or occasionally with saws. Unlined tunnels were enlarged by drill-and-blast or roadheader excavation.

Jan 1, 1991

By F. G. Boehm, T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force, Pv, a lateral force, Ph, and a longitudinal force, Pl. A method for estimating these forces is proposed that relates each of their values to the properties of the conveyor structure and rails, the shifting operation parameters, and other site-specific conditions. The effect of this force on the shifter behavior is analyzed, and guidelines are developed for selecting a suitable shifter. As well, other equipment requirements for the shifting operation are discussed.

Jan 1, 1988

By Darryl Amick, Keith A. Prisbrey, Lee E. Plansky

The problem addressed was to develop automated image analysis of metal welds to replace unreliable and costly 100% visual inspection. The objective was to evaluate neural networks combined with features from gray level surfaces. Photomicrographs of the welded seam in Zircaloy-4 channels used in nuclear fuel rod assemblies were examined. The methodology used was to select a set of morphological feature coefficients from Bessel Fourier morphological feature coefficients extracted from digitized photomicrographs. The selected morphological feature coefficients were then used to train a neural network. The approach was verified initially by successfully training a neural network using the known, secondary chemistry of the alloy welds. The results were good. The Bessel Fourier coefficients captured sufficient information from the metallographic images to distinguish weld quality. This approach has the combined advantages of compressing the images through Bessel Fourier coefficients and give the ability to rapidly process large amounts of data using neural networks.

Jan 1, 1993

By R. D. Hansen, R. R. Klimpel

This paper discusses the influence of frother type and dosage on recovery/selectivity in coal/sulfide mineral flotation as a function of particle size. It is shown that different frother structures exhibit quite different but consistent performance characteristics depending on the underlying particle size ranges involved as well as the dosage levels of both the frother and collector. The data presented on existing commercial frothers and some new special purpose experimental frothers is used to illustrate some general operator guidelines on proper frother selection and use.

Jan 1, 1987

By J. R. Koehler

Mining practices at the Sunnyside Mines, Sunnyside Coal Company, Sunnyside, UT, have been documented by U.S. Bureau of Mines researchers to preserve the extensive history of yield pillar-based longwall gateroad system evolution on the property. An overview of the historical mining conditions, practices, and innovations that resulted in the evolution of the two-entry yield pillar gateroad system currently employed at Sunnyside was developed from interviews of 30 long-time Sunnyside employees. Employing yielding chain pillars at Sunnyside virtually eliminates tailgate pillar bumps and contributes to reducing face bumps. Limiting the overall width of the gateroad system benefits bump control and especially, roof and floor stability.

Jan 1, 1994

By Normand Tassé

Reactive barriers, which consume oxygen, are prospective though unconventional alternatives to physical barriers for Acid Mine Drainage prevention. However, a reactive barrier implies a problem of duration. Pore gases were analysed in several wood waste piles in order to understand the factors which control wood degradation and help to determine the effective life span of such a cover. Long term efficiency seems to strongly depend on the degree of water saturation at the bottom of the pile, likely because the development of a microbial biomass in such an environment helps to keep the amounts of nutriments and readily metabolizable organic substrates at a high level, which in turn promotes oxygen consumption.

Jan 1, 2000

By Wei Wu

A computer-aided method for optimization of bench blast design in surface mines is presented. The design procedures basically consist of two steps. Firstly, a series of normalized, full- scale bench crater tests must be carried out in the field to find the optimum burden that produces the largest amount of acceptable fragments and other parameters that defines the effective fracture zone. Next, the locations and initiation sequence of blast-holes will be determined in such a way that each hole, at its time of firing, will be responsible for same amount of burden rock and will be in a position favorable to effective fracture of burden rock. A computer software "B.B." which can assist the second step of the design is fully introduced and its application is illustrated by an example.

Jan 1, 1992

By J. M. King, C. J. Boggs

Acquisitions of mineral properties and companies can saddle the acquirer with unexpected and substantial liabilities and obligations incurred by the acquired or selling company that are not readily apparent from review of the company's books or files. This paper will address selected areas of concern, such as environmental and reclamation liabilities, problems of foreign ownership by the buyer or seller, pension obligations, plant closing laws, effective title review, land use and zoning.

Jan 1, 1992

By R. R. Tatiya

The algorithms to model three stoping methods - sublevel, down- the-hole (DTH) and cut and fill stoping have been developed. These algorithms are capable of designing and performing economic analysis for one or more number of stopes in a continuous orebody. The design and economic analysis of each individual stope are first obtained. This is followed by the composite stope design layout and overall economics of the stopes under study. This paper describes only the stope design aspects of these models. The programs have been written using Fortran 77 with Tektronix graphical aids available at Imperial College Computer Centre (ICCC) London and are based on the basic data obtained from Khetri Copper Complex (KCC) and Rajpura Dariba (a zinc mine) in India. Minor modifications, however, may be necessary in some routines when used on other systems and for other mines.

Jan 1, 1989

By John E. Urbanic, William D. Faulkner, Robert W. Ruckel

Guidelines are presented for the selection, handling and regeneration of activated carbon used in gold recovery operations. The guidelines are based on Calgon Carbon Corporation's own investigations and experience gained in working with gold mine operators all over the world. Gold adsorption rate and adsorption capacity are shown to be independent variables thereby requiring testing of both properties when selecting activated carbon. Means of measuring these properties are provided. Historical activity tests on activated carbon are shown to be minimally useful in selecting carbon for gold recovery. Proper thermal regeneration techniques to maximize recovery of adsorption rate without weakening the carbon structure are suggested. Simple positive means of measuring efficiency of regeneration are presented. The subject of hardness measurement as a predictor of "in process" abrasion is discussed. The cost/benefit issue of carbon activity level is addressed.

Jan 1, 1986

By G. Schubert, H. Hoberg

A large number of diverse size reduction machines is currently available for the comminution of waste materials. Equipment selection is determined by the nature of the material to be treated and by its behavior under external mechanical stressing. Accordingly, wastes can be divided into those with elastictbrittle and those with ductile/viscous behavior. The scientific understanding of the comminution of wastes is lagging strongly as compared to that of the grain-shaped mineral raw materials. Only in a few unique cases have the fundamentals of the comminution of ductile or viscous materials been presented. The paper centers on a characterization and systematic analysis of the types of stress fundamental to comminution. On the basis of this discussion an overview is presented of the currently available technologies for the comminution of wastes, with attention centering on those machines designed for materials with ductile or viscous behavior.

Jan 1, 1998

By F. T. Paleari, J. A. Finch

Radial gas holdup profiles were measured in a 50-cm-diam, 400-cm-high flotation column using a multi-cell-conductivity probe. Three bubble-generation systems, including a system with up to eight vertical filter-cloth spargers, a system with three horizontal filter-cloth spargers and a system with three (horizontal) Cominco-type spargers, were examined. The variables investigated were the number of spargers, the symmetry of their arrangement and the height above the spargers. Batch water containing up to 20 ppm frother was used. Generally, the profiles tended to be uniform (flat) with some profiles exhibiting a slight "wavy" pattern. The vertical sparger arrangement proved to be the most difficult in which to achieve a profile symmetry. The horizontal spargers gave uniform profiles at right angles to their length but gave decreasing gas holdup along their length. The Cominco-type spargers gave slightly less scatter in the data. Switching off selected spargers to simulate a malfunction did not produce strong asymmetry in the profiles.

Jan 1, 1995