Search Documents

By Rajiv Hadkar, M. D. McKinley, J. B. Hiskey, B. J. Scheiner, G. W. Warren

Flyash from municipal solid waste incinerators containing roughly 13 to 15% Zn, 2% Pb and 0.2% Cd is an attractive material for simultaneous metal recovery and detoxification. Results have shown that Pb in flyash is present as PbSO4 and PbC12 and that about 70% of the Zn is present in the form of soluble amorphous compounds. Leaching results in a number of acid and basic lixiviants show that acid leaching is clearly more effective than basic leaching which is limited by low solubility of Cd and Zn. Cementation in acid solution with pH < 1 promotes redissolution of the precipitated metal. Successful zinc electrowinning from chloride leaching solutions has also been demonstrated, although Pb2+ and Na+ can be potentially detrimental. The presence of Pb2+ can prevent deposition of metallic Zn, forming zinc oxychloride, ZnC12.4Zn(OH)2, instead. High concentrations of Na+ can also result in precipitation of NaCl. This investigation has shown that hydrometallurgical treatment of MSW flyash through leaching, cementation and electrowinning is a potentially feasible method for simultaneous detoxification and recovery of metal values. Several issues have also been identified which would require further investigation for final process development.

Jan 1, 1993

By S. P. Mehrotra, P. C. Kapur

A phase-species classification is suggested for the mathematical models of flotation kinetics. Important models are discussed and the structure of their rate constants and parameters is analyzed. Split or enhancement factors are formulated for different kinetic models. The steady state dynamics of the flotation circuits can always be described in terms of these factors. For simulation of circuits, feed is characterized in a formal manner starting from a multivariate distribution of particles in flotation rate, size and mineral content. Synthesis of optimum circuits which simultaneously searches for the best process variables and structural parameters from a generalized master network is described. Trends in the areas of search algorithms, role of middlings and feed identification etc. are indicated.

Jan 1, 1989

By D. Corrigan, A. Ahmad, R. Sood, J. Bratt, R. Holt

Zinc oxide based electronic ceramics are being used increasingly to protect electric and electronic circuits against transient voltage surges. Varistors are produced by sintering and annealing ZnO based powder compacts through long sintering and annealing cycles. Because of the length of these cycles, a manufacturing plant is saddled with expensive high temperature equipment with low throughput. Ceramics Kingston Inc. has developed a new technology that uses 2.45 GHz microwave energy for sintering and annealing. The new technology has the potential for increasing equipment and labour productivity very considerably. Additionally, the new technology will result in appreciable energy savings and add flexibility to the manufacturing process. Microstructural examination of varistors sintered conventionally and by microwave technology showed considerably smaller grain size in the microwave sintered materials. The electrical properties of the microwave sintered ceramics compare very favorably with those of the ones sintered conventionally.

Jan 1, 1990

By R. Jerez

This paper describes practical applications of lineal" programming techniques to help in the planning of production, transportation and shipments at different coal mines. The models are being used by Cyprus Coal Company in eastern and western operations to plan coal production, economic dispatching and blending over variable time horizons. In addition, where a preparation plant exists, the models establish the amount of washing required to meet specific coal sales qualities. The emphasis on this paper is on model development and implementation together with a system to track coal flow and qualities, either raw from the mines to the loading facilities 01" processed through a preparation plant.

Jan 1, 1991

By A. Haghighat

A risk analysis on mine fires for all U.S. underground coal mines from 2000–2012 was completed to identify locations that have a high risk for fire incidents. The data for this analysis was extracted from the Mine Safety and Health Administration’s (MSHA) mine fire accident reports database. After identifying fire incidents from this database, a risk matrix was developed for underground locations that showed a significant propensity for fire incidents. This matrix associates the hazards and risks with the severity and frequency of their consequences at each location. These significant mine areas will be the concentration of future studies in fire behavior, suppression techniques, and simulation methodologies. INTRODUCTION Fires in underground mines pose significant hazards to personnel because of inherent restrictions to movement and limitations to egress routes. Despite improvements, mine fires remain serious hazards in underground coal mine. In order to better mitigate the risks from fire hazards in the modern underground mining environment, a better understanding of where fire events occur must be gained. The following paper presents an investigation on the number of fatal and non-fatal incidents in underground coal mines fires from 2000 to 2012. Three phases of risk assessment (i.e., risk identification, estimation, and evaluation) were applied to the recorded fire events from the MSHA incident database that occurred during this time period. Using this process, a fire hazard was first defined. This definition was then used to identify any incidents that had occurred as a result of the defined hazards. The seriousness of the injuries and damages were finally quantified for each incident though an estimate of severity and frequency and then aggregated according to underground location (ISO, 1999; Van Duijne, 2008). Using this approach, locations prone to incidents resulting from fire hazards were first identified. The risk for the occurrence a fire incident in general was then estimated for each of the identified locations. The results of this assessment will be used to improve fire simulation techniques for the identified, high risk underground locations. RISK IDENTIFICATION A risk for this assessment was defined as any single occurrence of a fire initiated by the ignition of gas, dust, or electricity. Each recorded occurrence of such an event in the MSHA incident database was counted as a single fire incident. Both non-fatal incidents that were reportable but did not result in a fatality and fatal incidents that fell into the aforementioned criteria were counted. Incidents in the MSHA database that were already classified as “generic” were not considered. The remaining incidents were then totaled and aggregated according to the underground location in which they occurred. In previous studies, a number of locations, which are listed in Table 1, were highlighted as high fire hazard areas (McDonald et al, 1980; Pomroy et al, 1995; De Rosa, 2004). These locations were used to group the fire incidents extracted from the MSHA incident database. The compiled numbers of non-fatal and fatal underground coal fire incidents from 2000 to 2012 are displayed in Table 1.

Jan 1, 2019

By A. G. Naguib

In essence, any magnetic separator operates on the basis of imparting a preferential magnetic force on particles of higher magnetic susceptibility which are to be separated from particles of lower magnetic susceptibility. A certain amount of directional deviation to the particles takes place thus allowing for collecting each category of particles separately. The forces in action on particles in a wet magnetic separator of the established designs can be analyzed in a simple manner as shown in Figure 1.

Jan 1, 1972

By Shan Mafi

he Broken Aro coal mine is located at the Woodbury Wildlife Preserve 11 km (7 miles) west of Coshocton, OH on State Route 541. Underground min¬ing at the 16-hm2 (40-acre) site took place during the 1910s. During the past five years, surface mining has occurred along the western and northern perimeters of the underground region. The Ohio Department of Natural Resources (ODNR), R&F Coal and American Electric Power (AEP) are involved in a project to remine the abandoned underground complex. The program also includes installing a mine seal made of fixated flue gas desulfurization (FGD) material. Previous mining activity in this area has resulted in an acid mine drainage (AMD) problem on portions of the reserve. In particular, a prominent AMD source is present in the Simmons Run drainage. The project goal is to eliminate or reduce the AMD that is discharging into the watershed. It was initially hoped that the Simmons Run drainage area could be economically mined. Accordingly, this area was included in the mine permit. However, experience with other previously mined areas on this reserve showed that the old mine workings were more extensive than originally thought. Old mine workings present several problems. The most significant are reduced coal recovery, poor coal quality and AMD liability. All of these problems increase mining costs. And the more extensive the old workings, the more significant the increase in cost. Based on R&F&apos;s experience with old mine workings in this area, it was decided that economic recovery of the Simmons Run drainage reserve was not possible. As a result, R&F excluded the Simmons Run drainage area from its early mine plans. Some time after it was decided not to affect the Simmons Run drainage area, R&F and ODNR&apos;s Division of Mining and Reclamation discussed the possibility of removing this area from the permit and attempting to correct the AMD problem as an Abandoned Mine Lands (AML) project. Specifically, the discussion centered around mining through a portion of the old mine workings to expose the mine openings in the highwall. Once exposed, the mine openings would be sealed using FGD material from the nearby Conesville power plant operated by AEP. In addition, there was interest in reclaiming the old tipple and associated gob pile located adjacent to Coshocton County Road 17 on the opposite side of Simmons Run. R&F attempted to eliminate the AMD problem by sealing the mine openings with FGD material. Once the seals were installed, they were covered with overburden. Monitoring wells were installed to determine the effectiveness of the seal and the inundation progress in the old mine workings as well as monitoring the quality of ground water. The project was jointly funded by revenue from the sale of the coal recovered during the project and AML funds. The FGD seal is expected to cause well water levels to increase above preseal elevations. However, the additional head pressure due to increased water depths in the underground mine may cause seepage through the bottom of the mine or out through the perimeter. The in¬creased water depth in the underground mine is expected to cause lower oxygen concentrations in the underground mine water. Since acidity is produced by oxidation of iron pyrites, less oxygen should result in better quality water. Monitoring wells will be installed before seal installation so that pre- and postseal water levels and well water quality can be determined. Surface sampling locations will be identified. These will be monitored before and after seal placement.

Jan 1, 1998

By M. J. McPherson, P. Mousset-Jones, G. Danko, F. Calizaya, K. You

The friction factor is one of the more difficult parameters to determine in ventilation planning. In practice, this can be estimated from published factors such as those of McElroy. The problem with this approach is that the selection requires some judgement, and the estimated values offer no more than guideline accuracy. This study, examines the effects of four factors on the coefficient of friction for a simulated mine airway. The factors are: airway cross-section, asperity height, flow direction, and cross-cut spacing. The study includes the modeling of a mine airway and the evaluation of the results from 13 experiments on flows of air over rough surfaces. The model, physically represented by a wind tunnel, includes a rough surface section which can be modified to simulate mine airways of various shape and asperity height. Most of the experiments were performed under controlled flow conditions during which the Reynolds number was varied between 50,000 and 300,0000. Based on this study, the friction factor for a mine opening was found to depend not only on the size and shape of the surface asperities but is also affected by the orientation of them in relation to the flow direction.

Jan 1, 1991

By S. S. Churchill

Introduction Amidst the apparent chaos of the final push to complete a major construction project, a small group of specialists works with great intensity. Armed with yellow "in test" and green "turned over to operations" tags, these startup engineers follow detailed preoperational test procedures to confirm that a plant is ready to operate. They follow a test schedule designed to complete individual process system in the order they will be needed by operations. After extensive preliminary testing, the startup engineers begin the truly exciting part of their work - initial operations. The thrill of engaging the clutch for the first time on a 10,000 horsepower grinding mill makes all the long hours worthwhile. Preoperational testing and startup are of critical importance to the success of a project. No other aspect of a construction project allows such opportunities for success or failure, and no other aspect is so critically influenced by careful planning. At Bechtel, the tasks of preoperational testing and startup are among the responsibilities of the Mine and Plant Operations group. The Preoperational Testing Process Preoperational testing is the transition phase between constructon and startup on a new plant. It includes the preparation of detailed test schedules and procedures. The schedules are used to coordinate construction completion activities, so that systems are available for startup and operations in a rational sequence. The procedures form the basis for performing the testing and documenting its completion. Tests include instrument calibration, wire insulation tests, wire termination verification, mechanical alignments and inspections, and system cleaning and flushing. Where possible, the systems are then operated on water and their performance recorded. Normally, either the construction contractor or a team of specialists has the responsibility to perform preoperational testing. Witnesses to the testing may be owner operations and maintenance personnel, engineers from the design firm, or specialists assigned to the project who provide assistance and guidance to the contractor in addition to witnesing the work.

Jan 1, 1986

By J. A. Brierley, S. N. McIntosh, C. L. Brierley, E. G. Baglin, E. G. Noble, D. L. Lampshire

The U.S. Bureau of Mines investigated column bioleaching as a means of recovering manganese from a domestic low-grade oxide ore. Manganese was solubilized from the ore using indigenous heterotrophic microorganisms and molasses as the nutrient source. The effects of medium flow rate, molasses concentration, and frequency of medium replacement on the rate of manganese extraction were examined. Results showed that flow rates between 0.4 and 8.1 L/min/m2 had little impact on manganese extraction, while an increase in the total amount of molasses applied during leaching directly affected the extent and rate of manganese extraction. Manganese extractions of more than 90% were achieved in 12 weeks of bioleaching in column tests using 500 g charges of ore. Sugar utilization by the microorganisms and formation of organic acid metabolites were monitored by high performance liquid chromatography (HPLC). Two methods were evaluated to recover manganese from the sugar- depleted bioleaching medium: (1) adsorption onto weak cation exchange resin, followed by stripping and precipitation techniques; and (2) direct precipitation of the manganese as MnCO, using ammonium carbonate. Both recovery methods removed at least 95% of the solubilized manganese from the medium as a carbonate salt. The stripped molasses medium was replenished with fresh molasses and recycled back through the bioleach column, successfully leaching more manganese.

Jan 1, 1993

By C. J. Bise, D. A. Poukhovski

Hazard recognition and prevention of accidents are two components of the 30 CFR 48 training requirements, which are mandated for new miners and newly employed experienced miners. These components are also part of the annual refresher training course required of all miners. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine and shall include a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition presents a particular challenge to safety-training specialists, because they are often limited in their ability to adequately gauge the level of awareness of the individual prior to training. Further, they must also assure that the training is relevant and presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics, because it can be used in pretraining and posttraining modes for assessment of training effectiveness, in addition to its use as a presentation tool. This article presents a recent approach, developed at The Pennsylvania State University, that applies the technology for the assessment and instruction of accident prevention through hazard recognition. The application is prepared for surface coal mines.

Jan 1, 1999

By Joseph J. Wojcik

INTRODUCTION A great deal more is involved in a sampling effort directed at a placer deposit than physically capturing a quantity of representative material and extracting the desired component. The distribution and dimensions of the sample sites must be chosen after consideration has been given to the type of deposit and the concentrating mechanism. Interpretation of the sampling results is likewise an extremely important part of the sampling program. SAMPLE SPACING The interpretation begins with the selection and design of the sampling program. A decision regarding genesis of the deposits and their geometry must be made in order to select a suitable technique and sampling pattern. Deposits differing genetically will have differing distributions and degrees of concentration.

Jan 1, 1992

By Vernon R. Degner

The past two decades has seen the application of the mechanical flotation machine, originally developed primarily for metal1iferous ore beneficiation, increasingly applied to cleaning coal in the 28x0 T. Mesh size range. Internal cell hydrodynamic studies of mechanical flotation machines of all sizes, as well as computer aided modeling studies of flotation kinetics has, within the last five years, established a basis for optimizing coal flotation circuit design and machine operation, and has a1 so pointed a way toward improvements in mechanical flotation machine design for the future. Consideration of the trend toward increased fines produced by current mining techniques, as well as the environmental need for a progressively cleaner product, lends support to basing the design of the mechanical coal flotation machine of the future on finer feed; below 100 microns in size. Future types of mechanical flotation machines, which may satisfy the fine coal cleaning requirements for a significant improvement in product grade while maintaining the combustible recovery levels of current technology, are discussed.

Jan 1, 1988

By K. V. K. Prasad

Solution of most engineering problems requires, in addition to vast numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity. However, it is only recently that approaches like the expert systems methodology have been developed to incorporate the judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or "shells" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development of a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.

Jan 1, 1989

By A. R. Wagner, E. Berkman

The use of high-resolution seismic surveys in coal exploration and mine development is becoming established as a standard technique in the industry. Their most significant contribution is in the effectiveness of reducing the number of core holes needed to understand the complex geological nature of coal by identifying geologic faults and mapping coal seam continuity and relative coal thickness. With these goals in mind, a high-resolution seismic survey was conducted in 1980 in the Wasatch Plateau coalfield of Utah. As a result of the success of this initial survey, numerous additional surveys have been performed over the past six years.. The interpretations of these subsequent surveys have led to the location of faults, fluvial channel sandstones, and coal thickness trends. This paper presents a review of high-resolution seismic technology as applied to coal exploration followed by three case histories, two of which illustrate the utility of the technique related to coal thickness determination and faulting and one that serves as an example of pitfalls in interpretation.

Jan 1, 1987

By Thomas J. Peters

At the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral investigation of about 85,470 acres of the Diablo Mountain Wilderness Study Area, to determine mineral resources and mineral resource potential. The study area is in Lake County Oregon, about 45 miles northwest of Lakeview. Fieldwork was conducted in 1986, 1988, and 1989. Geologically, the study area lies on the northwest edge of the Basin and Range physiographic province, a region of fault block-formed mountains and basins characterized by interior drainage. Consolidated rocks are mostly Tertiary basalt and tuffaceous sedimentary rocks. Low-lying areas are covered by Quaternary alluvial-fan, sand-dune, playa, lacustrine, and landslide deposits. The principal structural features are normal faults that have large vertical offsets; these faults are typically concentrated at the margins of large horst and graben. The 34,310-acre "additional," or western part of the area was mainly studied in 1988 and borders the east shore of saline Summer Lake. In this portion of the study area there is potential for undiscovered resources of soda ash, boron compounds, and sodium sulfate as well as by-products, which include magnesium compounds, salts, potash, bromine, lithium, and tungsten associated with brines. No energy or mineral resources were identified in the study area, but brines within lake and playa sediments contain concentrations of chemical components suitable for the production of soda ash, boron compounds, and sodium sulfate. Possible by-products include potash, salts, bromine, lithium, magnesium compounds, and tungsten. Limestone from the study area could be used in the recovery process of brine components or agricultural uses. The study area includes thermal springs and lies within 2 miles of the Summer Lake Known Geothermal Resource Area. Local production of geothermal power by the binary process may be economically feasible. Soda ash, soda ash products, and boric acid are widely used in fluxing metals, and have important applications and markets in the aluminum industry in the northwest and the developing Chinese counterpart. Evaporite commodities are essential to many "backbone" industries, and to many new applications and advanced materials. Markets for brine mineral products appear to be undergoing steady and strong growth, especially in the Pacific Northwest and in Pacific Rim countries. Soda ash produced near the study area would be 55 percent closer by rail to marine export at Portland, Oregon, than trona deposits of the Green River District (Wyoming). Soda ash and a daughter product, caustic soda, and sodium borohydride will receive increased application in the bleaching of paper pulp for environmental reasons. Caustic soda, used in many industrial processes, is more environmentally friendly when derived from soda ash than when produced from sodium chloride salt, because of the absence of a chlorine by-product. Producing soda ash from brines, a type of in situ" mining, can be done with minimal environmental degradation, and mining natural soda ash is environmentally as well as economically preferable to synthetic soda ash production.

Jan 1, 1995

By Glenn A. Shirey, Robert D. Stoessner, S. Gopalakrishnan

Under a contract awarded by the U.S. DOE-PETC, the Pennsylvania Electric Company and New York. State Electric and Gas Corporation are conducting a test program to evaluate and optimize the performance of a two-inch air-sparged. hydrocyclone (ASH) for cleaning fine coal. The test program is being conducted at the Homer City EPRI Coal Quality Development Center, utilizing Upper Freeport coal classified to minus 0.15 mm as the process feed material. A matrix of experiments has been conducted to establish the influence of significant design and operating variables (including overflow and underflow orifices, inlet slurry pressure, airflow rate, and reagent dosage) on the production of deep cleaned coal. Performance of the ASH is being compared to conventional froth flotation, utilizing advanced techniques and selected flotation reagents. This paper focuses on work completed to-date to optimize the performance of the air-sparged hydrocyclone for cleaning fine coal. INTRODUCTION The Pennsylvania Electric Company (Penelec) and New York State Electric and Gas Corporation (NYSEG) have been evaluating advanced fine coal cleaning processes for the production of compliance grade coal (1.2 pounds S02/million Btu). Laboratory bench-scale froth flotation results were compared with results of advanced flotation processes as performed by various organizations, utilizing the same coal feed. Among the processes evaluated, the air-sparged hydrocyclone (ASH) - developed by Dr. Jan Miller at the University of Utah - was considered to offer the best potential for retrofitting into an existing coal preparation facility because of the increased capacity per unit volume. The ASH has been shown to process over 100 times the throughput of conventional froth flotation cells. In May of 1988, Penelec/NYSEG was awarded a contract from the Department of Energy&apos;s Pittsburgh Energy and Technology Center (DOE-PETC) to optimize the performance of a five cm (two inch) ASH for producing compliance grade coal from raw classified minus 0.150 mm (1.00 mesh) Upper Freeport coal, and to compare its performance with conventional froth flotation utilizing advanced techniques and selected flotation reagents. The test work is being conducted at EPRI&apos;s Coal Quality Development Center (CQDC) in Homer City, Pennsylvania, utilizing a circuit processing 0.10 to 0.25 tons of coal per hour. Other members of the Penelec/NYSEG contract team include the University of Utah, Advanced Processing Technologies, Inc., Davy Dravo, Kaiser Engineers, Ebasco Services, and Management and Technical Systems. ASH DESCRIPTION AND OPERATION The ASH-2 System is a five cm ID (actually 4.76 cm) air-sparged hydrocyclone manufactured by Advanced Processing Technologies, Inc., under license from the University of Utah, for the purpose of research, evaluation and development. A schematic drawing of the air-sparged hydrocyclone is presented in Figure 1. Basically the air-sparged hydrocyclone consists of two concentric right-vertical tubes, a conventional cyclone header at the top, and a froth pedestal at the bottom. The inner tube is a porous tube through which air is sparged radially. The outer nonporous tube simply serves as an air jacket to provide for even distribution of air through the porous inner tube. The slurry is fed tangentially through the conventional cyclone header to develop a swirl flow in the radial direction. Air is sparged through the jacketed, inner porous tube wall and is sheared into small bubbles by the swirl flow. Hydrophobic particles in the slurry collide with these bubbles and, after attachment, are transported radially into a froth phase which forms on the cyclone axis. The froth phase is stabilized and constrained by the froth pedestal, thus moving towards the vortex finder of the cyclone header and discharged as an overflow product. Hydrophilic particles generally remain centrifuged in the slurry phase and are discharged as an underflow product through the annulus created by the froth pedestal.

Jan 1, 1989

By J. M. Applegate, C. L. Morgan

Introduction In the same way that a blueprint communicates informa¬tion about a structure, a systems architecture should provide information that guides the construction and implementation of a computing system. Taking the blueprint analogy a step further, a plot plan can also show where, in the "bigger picture," a particular design fits (if in fact it does) and what a builder needs to know about the environment in which he or she will operate. In the context of business systems, a meaningful architecture should convey the following: • the primary purpose of computer-based systems rela¬tive to particular tasks or operations, • the relationship of the systems to each other and an indication of their interaction and dependencies, • the relationship of the systems relative to the organiza¬tion and its objectives, • indications of where IS/IT resources can best be allo¬cated to support the organization and • the overall context in which new systems and technolo¬gies can be assessed for both their impacts on current systems and on the organization itself. In theory, a well-designed systems architecture should allow an organization to focus its resources on those aspects of its business that matter most, thus, leveraging investments in information technology to a competitive advantage. In addition, the way that a computing systems architecture is represented should be un¬derstandable to non-IT staff, and it should be eas¬ily recognized by the people it supports. This pa¬per attempts to show that a meaningful systems model exists and that its applica¬tion to mining can achieve the desired results. The following discus¬sion is based on the au¬thors interpretation of a concept referred to as the computer integrated manu¬acturing (CIM) model, as developed by Allen-Bradley. An inherent strength of the CIM approach is that the model combines aspects of business-reporting structures with the manufacturing process itself. What results is a systems frame¬work that is aligned with relevant business processes and is, therefore, easier for non-IS/IT personnel to interpret. The successful application of the CIM model can be seen in a large number of both discrete and process-manufacturing facilities throughout the United States. This paper provides a brief overview of the CIM model and then describes how the model can be applied at a conceptual level to the mining industry. Finally, this paper proposes an extension to the CIM model that the authors believe will make it easier to understand and apply. CIM model As shown on Fig. 1, the CIM model begins with the most detailed levels of process equipment and works its way up to the highest level of consolidated financial reporting. Systems at each level are characterized by common attributes, users, time frames, etc., providing a clear picture of their interac¬tion. Further analysis of the relationships between systems and between levels provides insight into the opportunities for integration. Regardless of the industry or processes involved, the CIM model provides a framework in which the characteristics of systems and the data they manage can be predicted based on the nature of the business function they support. In general, as data moves upward from the lower rungs of the CIM model, it changes from de¬scribing the physical na¬ture of a process to describ¬ing its financial aspects (e.g., from productivity to cost). The time frame to which data applies also transitions from a very short duration, perhaps only milliseconds, to financial or regulatory reporting time frames that may span years. In a simi¬

Jan 1, 2000

By D. Maxton

INTRODUCTION This paper traces the application of High Pressure Grinding Rolls (HPGR) at industrial and pilot scale in Australia. The Argyle Diamond Mine installed the first of two smooth segmented HPGRs during 1990 in an open-circuit secondary-tertiary crushing application to increase throughput. In 2002 a third HPGR was added to improve liberation and so increase the recovery of smaller diamonds. The latest improvements in wear technology (tyre with tungsten carbide studs) were incorporated in the design of this machine. Extensive HPGR pilot-plant trials were undertaken during the 1990s at both the Kalgoorlie Consolidate Gold Mine and the Boddington Gold Mine. The purpose of these trials was to evaluate HPGR as a method to increase throughput, as an alternative to SAG milling, and also to ascertain if downstream benefits existed. One of the challenges for HPGR circuit designers is to translate what occurs at small laboratory and pilot scale into what is likely to happen in a full-scale circuit. Scale-up from pilot machine results is normally recommended by manufacturers. However, such tests need relatively large quantities of material, particularly if meaningful data on wear are to be obtained. Laboratory tests are preferable, as they need relatively small quantities of ore, but may be questioned in terms of how they relate to full-scale operation. Modelling and simulation have played a particularly important role in this respect in Australia. Models are available which have proven to be very accurate at being able to scale throughput and specific energy response from laboratory to industrial machines. More recently, work in Australia has also been done in developing a model which has the potential to scale laboratory wear data as well.

Jan 1, 2004

By L. Adler

INTRODUCTION The purpose of this paper is to describe in engineering terms the singular and basic operational kinematics of all excavating and bulk handling equipment. The safe and efficient use of equipment will be fostered by enabling the engineer to conceptually duplicate the operators&apos; "tasks" in directing and controlling it. A simple graphical and notational scheme will be introduced to define the essential gross repetitive motions. The significance of this effort includes filling a vital analytical gap at the work face, and in establishing direct communications between the engineer and equipment operator. Since all types and sizes of earth- moving equipment are covered, a major concern has been to integrate equipment specialties into d single encompassing discipline. Equipment types are closely related to the working conditions, and their selection and evaluation are also considered. The extension to human factors analysis is natural and predictable. Since human [actors are involved, the operational analysis can also be considered a catch-all for many subtle vagaries. BACKGROUND Symbolic modelling linked to a notational system will be developed and intensively used. This constitutes the "language of science," providing a shorthand method which gives immediate recognition, is fluent, explicit, reinforcing, unequivocal and provides limitless associations. Many examples of symbolic modelling exist in chemistry, physics, the military, engineering sciences and it is a major tool in mapping. Its use is so ubiquitous that it often goes unnoticed. On the other hand it must be realized that something is lost in simplifying and idealizing what is an extraordinarily complex occurrence. The components describing the basic operational kinematics of equipment include: (1) the vehicular motions as a rigid body and (2) the job-end motions focussing on excavating (Adler, 1985). These provide all of the components in the load-haul-dump sequence (L-H-D) , and will yield three dimensional expressions. Complex patterns can also be assembled from these simple elements. An existing equipment designation employed in earthmoving will be integrated into this approach (Carson, 1961). Along with the basic motions, corresponding working conditions will be noted.

Jan 1, 1986