Search Documents

By Glen Mc Gavigan

The roof of the Sishen cave is being mined in order to exploit 6.8Mt of high grade ore. The cavity is filled with quartzite backfill in order to support the roof in the event of collapse. The cave dips at approximately 37o, is 260m along dip and 70m along strike and has a total volume of 261,391m3. GPS and optical monitoring techniques were attempted to detect subsidence but proved to be impractical. The GroundProbe Slope Stability Radar (SSR) uses differential interferometry to measure sub millimetre movement in a rock face. The SSR was applied in a non production situation and detected subsidences of 38mm/day before visual signs of instability were detected. The rate of deformation detected was slowing as a result of the roof coming to rest on underlying backfill. Monitoring during production drilling detected a sudden subsidence of 18.6mm/hour which resulted in the evacuation of personnel from the area. Further inspection of data showed that the rate of deformation was slowing and production was allowed to continue without further incident. The SSR has helped dispel the fears of workers and has proven that subsidence can be accurately measured and delineated with the SSR.

Jan 1, 2006

By I. W. van der Merwe

Recently, a new kind of filtration has emerged, namely nano-filtration (NF). It is a membrane-based process which exhibits totally unique separation characteristics for dissolved salts as well as for many non-charged species. By exploiting the particular separation characteristics of this new membrane type, many unique and novel separations have been made possible. The basis for separation by nanofiltration is the negative surface charge of the membrane. This results in rejection of multivalent anions, whilst associated cations are also rejected to maintain electro-neutrality. This peculiar property enables separation of dissolved ions such as sulphate and copper from acid, whilst the acid may be purified for reuse. This paper aims at providing an overview of the principles of nanofiltration, illustrated by particular examples.

Jan 1, 1998

By G. C. Smith

Process control applications in the minerals processing industry have grown extensively over the years due to the many benefits derived, both financially and operation-wise. Although control theory is widely known, conventional control does not address many of the problems posed by minerals processing circuits. Some of these problems include interactions between process units, large dead times, few and sometimes unreliable measurements of process variables, non-linear systems, disturbances entering the process, processes with varying dynamics, and many more. For the past 26 years Mintek has been active in the field of providing specific, customized solutions for the minerals processing industry. This paper focuses specifically on applications in milling and flotation control. The underlying control principles have been applied to a wide range of other processes including submerged arc furnaces. Advanced control application is implemented on a common advanced control platform, called the PlantStar. Much innovation has been brought to the fore in terms of adapting theoretical techniques and developing new methods to resolve specific milling and flotation circuit issues by using process control. The general approach adopted by Mintek when implementing advanced control is to enforce stabilization of the process as a solid foundation for optimization strategies to be built upon. In doing this, a robust control solution is presented, and the end result is flow and level stability, better product quality regulation, increase in throughput and a stable feed to downstream processes. The MillStar advanced milling control system ensures that the milling circuit is at all times easy to operate while achieving optimum product quality and throughput. Stabilization should include product size regulation and sump level control. Another important aspect of stabilization control is the handling of milling circuit constraints without introducing cyclical behaviour and with minimal disturbance to the final product quality. Process constraints may include factors such as process water limitations, cyclone feed density, and cyclone underflow angle. An optimization strategy should be developed to increase the mill throughput without affecting product quality or introducing mill overloads. The relationship between solids feed and power draw is examined and manipulated for optimization. The interactive nature of flotation circuits and the presence of recirculating streams tend to make satisfactory control almost impossible with conventional techniques such as PI (Proportional plus Integral) or PID (Proportional, Integral and Derivative) control. The FloatStar Level Stabilizer simultaneously considers all the flotation levels in a circuit by use of a multivariable algorithm, and takes compensating action in anticipation of disturbances. The FloatStar Flow Optimizer is an optimization strategy that controls the concentrate flow rate between various sections of a flotation circuit (e.g. Rougher ?Cleaner; Cleaner ?Recleaner). By controlling the concentrate flow between the sections, the mass pull, circulating loads and residence times of the circuit can be stabilized, thereby enhancing the performance of the flotation process. Optimizing grade and recovery are coupled with the dynamic optimization of circulating flows. The FloatStar Grade-Recovery Optimizer will maximize the grade in a section, whilst ensuring that recovery or any other process specific limits remain within predefined limits. With successful applications on several milling and flotation plants worldwide processing amongst others PGMs, gold, copper and nickel, Mintek has shown that it is a leader in milling and flotation control innovation

Jan 1, 2004

The current methodology to design stope support systems in South African gold and platinum mines is based upon the tributary area concept. The discontinuous nature of the hangingwall rock is not adequately addressed, and mechanisms leading to rock mass failures between adjacent support units are poorly understood. The work reported here aims to formulate a basis for quantifying support mechanisms and gain insights into the influence of rock discontinuities on stable hangingwall spans. Numerical models are used to qualitatively investigate the stress transfer from the support units to the discontinuous hangingwall. Stable hangingwall spans are quantified by considering two failure mechanisms, namely (i) beam buckling, and (ii) shear failure due to slip at the abutments. The output of the proposed design methodology is appropriate site specific support spacing, based on discontinuity spacing and orientation. The method is particularly suited to mines at intermediate and great depth, where typically the hangingwall is highly discontinuous due to face parallel mining induced fractures. Results of parametric studies show that with increasing in situ compressive hangingwall stress, beam thickness and friction angle, hangingwall stability is increased, leading to wider stable hangingwall spans between adjacent support units.

Jan 1, 2000

By T. Z. Mugodi, D. R. Fleming

Information and Communications Technology (ICT) is defined as ‘The goods and services that support the electronic display, processing, storage and transmission of information’. Early in 2002 the South African Department of Trade and Industry (DTI) commissioned a study into the diffusion and adoption of ICT in eight sectors of the economy. The platinum mining Sector was one of these. The key findings presented in this paper are based on the platinum sector component of that study. The paper examines the theoretical basis behind technology transfer and innovation diffusion and presents the results of an ICT diffusion survey carried out in the South African platinum mining sector. ICT is shown as the modern day technological tool which is an accelerator of economic development. The current state of ICT diffusion in the platinum mining sector is defined and projections for the near future are given. Recommendations which will ensure smooth and full adoption are presented and justified.

Jan 1, 2003

By R. P. Singh

A mine fire model gallery has been designed and constructed on the premises of the Central Mining Research Institute, Dhanbad, India to perform systematic in-depth studies on various aspects of mine fires. The gallery is 65.5 m long and 5.86 m2in cross-section and it is divided into firing and non-firing zones. It is equipped with a computer-aided online telemonitoring system that has 130 sensors, two data loggers and computer peripherals for continuous recording of various fire parameters. A fan to generate airflow through the gallery has been installed at its end. Two sliding doors and one rolling shutter were also provided for sealing and regulation of airflow. Two sets of experiments have been carried out in the model gallery maintaining air velocity of 1 and 1.5 m/s through it. In the experiments, the inner sides of the firing zone, 22 m in length, were lined with a thin layer (8?10 cm thick) of coal slabs. Two fire suppression techniques viz. flushing of liquid nitrogen (LN2) and infusion of high pressure high stability (HPHS) nitrogen foam were tried to quantify their effectiveness under dynamic fire conditions. The paper addresses important design features of the gallery, its instrumentation system, the experimental procedure adopted and important findings from the experiments. It has been observed that the intensity of the fire was very high after one hour of its initiation and continued for 3?4 hours. During the period, frequent backlash with smoke and flame was noticed. The efficacy of the fire suppression techniques has been assessed interms of reduction in temperature, generation rate of CO2and CO, and heat release rate. The study reveals that high pressure high stability (HPHS) nitrogen foam is more effective in controlling open fires than liquid nitrogen is. Keywords: Model gallery, telemonitoring system, velocity, temperature, pressure, gas concentration, intensity, liquid nitrogen, high pressure high stability nitrogen foam.

Jan 1, 2004

By Hornsey R., P. van der Merwe

The Two Rivers Project is a feasibility study to evaluate the UG2 chromitite layer on Dwarsrivier372KT, Mpumalanga Province, South Africa. The project, which commenced in August 2001, is expected to receive go-ahead early in 2003. The project sponsors (AVMIN 55%, Implats 45%)required project delivery within a short timeframe requiring optimization of the geological and geostatistical programme. Geological modelling was carried out in parallel to the drilling programme, and significant up-front geostatistical preparatory work was done. The time saving was approximately 4 – 6 months on project delivery. The cost saving to the project (excluding NPV considerations) is estimated at R20–30 million. Keywords; Two Rivers Platinum, Dwarsrivier 372KT, UG2 chromitite layer.

Jan 1, 2003

By P. N. Erasmus, M. Heyns, M. J. Pretorius

The characteristic of stope supports plays a vital role in the design of the supports. This paper deals with the characterisation of both cellular lightweight concrete and timber supports since both supports absorb and dissipate the energy in different ways. The behaviour of the support and hence its performance is simulated for different loading conditions by constructing a model consisting of various mechanical components like springs, dampers and blow-off valves. When the force exerted by the stope support increases significantly during deformation of the support, the stresses in the hangingwall could exceed values where failure of the hangingwall may occur. There is a need to understand this phenomena and the work presented in this paper is a first attempt to start with the characterisation of the stope support. Les caractéristiques des supports de taille jouent un rôle vital dans la conception des supports. L’étude présente traite de la caractérisation des supports cellulaires en béton léger et en bois, puisque ces deux types absorbent et dissipent l’énergie de façons différentes. Le comportement du support et par conséquent sa performance est simulée pour des conditions différentes de chargement en construisant un modèle qui consiste en des organes mécaniques variés tels que ressorts, registres et valves d’échappement. Quand la force exercée par le support de taille augmente considérablement pendant la déformation du support, les contraintes dans le toit peuvent dépasser des valeurs qui pourraient entraîner la défaillance du toit. Il est nécessaire de comprendre ce phénomène et l’étude ici présentée constitue un premier essai dans la caractérisation du support de taille. Die Charakteristika der Strossenunterstützung spielt im Design von Unterstützungen eine vitale Rolle. Diese Arbeit befaßt sich mit der Charaketerisierung sowohl der porösen Leichtgewichtbeton- als auch mit der Holzunterstützung, da beide Unterstützungen Energien auf verschiedene Art und Weise absorbieren und auflösen. Das Verhalten der Unterstützung und folglich seine Leistung wird für unterschiedliche Ladezustände simuliert, indem ein Model konstruiert wird, welches verschiedene mechanische Komponenten wie Federn, Dämpfer und Ausblaseventile enthält. Wenn die von Strossenunterstützung während einer Unterstützungsdeformation aufgebotene Kraft signifikant ansteigt, könnten die Spannungen im Bereiche des Stollenfirstes Werte überschreiten wo ein Versagen des Stollenfirstes eintreten kann. Es besteht die Notwendigkeit dieses Phänomen zu verstehen, und die Arbeit, die in diesem Elaborat dargestellt wird, ist ein erster Versuch, mit der Charaketerisierung der Strossenunterstützung zu beginnen.

Jan 1, 2003

By P. R. Brenchley

Main ore pass systems should last the life of a mine, and too often expensive and hazardous remedial measures are required to repair a damaged ore pass in an attempt to extend its life. In order to maximize the life expectancy of all ore passes at Moab Khotsong, ?wearing blocks? and ?softer support? systems, combined with basic rock engineering principles, have been implemented. Failure of an ore pass can have severe financial implications, both indirectly because the ore pass cannot deliver the broken rock either from level to level or directly in the shaft ore pass system to the required level for tramming to take place, and directly due to the cost of the repair work that is required. Several factors need to betaken into consideration so that production interruptions are eliminated or minimized. Investigations of damaged ore passes at Moab Khotsong and surrounding mines revealed some interesting mechanisms of damage, and some innovative methods of reducing or eliminating the damage have been implemented at Moab Khotsong. The system design was based on 30 years, experience in main shaft rock passes. The design was to counteract scaling, hang-ups and dust problems associated with main rock passes, and the objective was to increase the life of rockpasses. These problems, including the initial design aspects to try and eliminate the repair measures, are discussed in detail.

Jan 1, 2006

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By W. U. Reimold, R. Armstrong, R. G. Charlesworth

For many years rockbursts have plagued the mining industry. Although much research has gone into studying this phenomenon only a small proportion of it has been on the actual source mechanism. A study was recently carried out to compliment the previous work done on the micro-structure of these features and to compare it to the micro-structures seen on shatter cones, from meteorite impacts. Both optical and electron-microscopy were used during the study. Samples were collected from rockburst sites by the CSIR Miningtek Rockburst Investigation Unit, and from the collar of the Vredefort Impact Crater. In the optical-microscopy study, the pinnate fractures observed in previous studies were seen in the shatter cones, through all the material. In the rockburst samples, the fractures were observed only in the quartz grains. Quartz micro-crystals were present in the rockburst samples and appeared to be the product of comminution rather than crystallisation. Cataclasite was present on rockburst and shatter cone fracture surfaces. The observations of the shatter cone surfaces with the scanning electron microscope are in agreement with previous work, including the observed presence of melt features, spherules and spheroidal material. The deformation in the rockburst samples is concentrated in the quartz grains, highly complicated with brittle features like sub-conchoidal structures and step structures present. A quartz spherule was identified on one rockburst sample and rhombic-dodecahedra type micro-crystals were present and seen fracturing off quartz grains. It is clear that the rockburst and shatter cone fracture surfaces are quite different; the shatter cone deformation is equally distributed across the sample and involves plastic-deformation, while the deformation in the rockburst material is concentrated in the quartz grains and, with the exception of spherule formation, is brittle. This study agreed with the current explanation for the formation of the rhombic-dodecahedra, and disproved the possibility of it being coesite or fine-grained meta-chert. Although there is no definite evidence of the mechanism of formation of the spherule, it is believed to be the product of vaporization and condensation, and the presence of this material indicates the extreme conditions under which this event occurred.

Jan 1, 2003

By L. Hekkala, J. Ollila, J. Keihäs, P. Mäkelä

The Outokumpu Steel Belt Sintering (SBS) Technology is used for manufacturing chromite pellets that are charged into a smelting furnace for ferrochromium production. One of the main elements in successful furnace operation is the control of gas flows inside the furnace, giving improved temperature distribution in the bed during the process. Computational Fluid Dynamics (CFD) gives excellent opportunities for studying these phenomena. An investigation using CFD can be performed relatively fast. For example, implications of different configurations can be studied within a day and an optimum design chosen. Therefore, Outokumpu Technology has developed a Steel Belt Sintering Model (SBSM), which takes advantage of a commercial CFD code. Each main physicochemical event occurring in a steel belt sintering furnace is incorporated independently in the SBS model as a sub-model, enabling every event to be studied separately. The commercial CFD code solves mass, momentum, species and energy equations for determination of the gas flow, composition and temperature. In addition, the Outokumpu SBSM takes into account the moving pellet bed, drying of pellets interms of water content, coke combustion, oxidation and reduction of chromite and the decomposition of carbonates and silicates. During the development of the model, numerous laboratory-scale tests were performed. The sub-models were validated against the laboratory tests. The reliability of the Outokumpu Steel Belt Sintering Model was validated against a pilot-scale batch-sintering furnace by comparing the modelling results against measurements. The aim of this paper is to give a brief presentation of the Outokumpu steel belt sintering model by showing some general modelling examples. Emphasis has been placed on demonstrating some of the main features of the model.

Jan 1, 2007

By Y. Jin

Magnesia ramming materials have been widely used in China instead of magnesia bricks as furnace lining materials of ferroalloy refining furnace. The paper introduces the development of the ramming material, recounts its chemical composition, physical property and application characteristics. Because of its high MgO contents and fine sintering property, the ramming furnace bottom has the properties of good refractory, monolithic construction and thermal shock resistance. The changes in mineral composition and furnace tearout characterization show the reasons for the bottom?s long service life. The obvious benefits are widely achieved, the annual saving cost in refractory is about 2 millions US dollars.

Jan 1, 2004

By P. Sharma, J. C. W. Fowler

This paper discusses the wind blast / air blast phenomenon, how it is managed in coal mines and how it might best be managed in other underground mines. L'article qui suit a pour objets de décrire le phénomène de tir a l'air comprimé et les méthodes de modération de celui-ci dans les mines de houille, et d'indiquer de quelle manière il pourrait être surmonté dans d'autres mines souterraines. Dieses Seminararbeit diskutiert die Windexplosion / Luftexplosion Phänomen, wie es in Kohlenberg-werken geleitet wird, und wie es am besten in anderen untertage Bergwerken geleitet werden könnte.

Jan 1, 2003

By O. F. Ochonogor

Laser metal deposition (LMD) is an additive manufacturing technique whereby a stream of metal powder is consolidated by a focused laser beam on the surface of a substrate or engineering component. The interaction zone between the laser beam and powder particles is scanned superficially, generating tracks of deposited material. The tracks are overlapped in a deposition strategy in accordance with slices of a CAD model. Successive layers of material are built up to fabricate a near net shape part. In this work, the technique is used to fabricate metal matrix composites (MMCs) by using an elementally blended feedstock combining metal and ceramic powders in the melt pool, which melt and solidify to create the required morphology. Ti6Al4V + TiC MMCs were produced with 10, 20, and 30 vol.% reinforcing ceramic, and Zr + TiC MMCs were fabricated with 10, 20, and 30 vol.% TiC. The deposited thin walls were analysed using optical microscopy, scanning electron microscopy (SEM) with energy dispersive spectroscopy (EDS), and indentation testing. In both systems, the analysis revealed the presence of partially melted TiC particles embedded in the metal matrix along with fine dendrites of re-solidified ceramic. The dendritic structures in the Ti-based composites were confirmed as TiC, whereas in the Zr-based composite the Zr metal reacts with theTiC to form ZrC, leaving Ti in solid solution. Both the MMCs show an increase in microhardness with increasing ceramic (carbide)content, reaching a peak HV0.1 value of 500 in the Zr- based MMC and HV0.1 of 550 in the Ti based MMC.

Jan 1, 2012

By W. V. Mutler

Present day capital costs are analysed for a 2 000 metric tonne per day (MTPD) pyrite burning plant and compared with a sulphur burning plant of the same capacity. Power, raw material and steam production rates are then compared for the two facility types. A sensitivity analysis is conducted to highlight the impact changing sulphur, pyrite, capital and operating costs have on the relative economics of these feeds. Technological improvement effects on capital cost and energy recovery are also discussed. Besides the steam produced from the burning of pure sulphur or pyrite, plants using an advanced form of heat recovery can produce up to 10 bar steam using heat from acid formation. The quantity depends on the overall water balance which is influenced by such factors as gas strength and product acid concentration. Modern materials and innovative process design also improve the ability to increase the high pressure steam from the roaster boiler in pyrite plants above the traditional 1.25 kg of superheated steam per kg of acid produced.

Jan 1, 2009

By R. A. Williams

Electrical impedance tomographic methods have been applied to a variety of mineral and chemical processes in the laboratory and on plant. This review paper surveys technical developments in measurement methods to enable quantitative extraction of key process information in the form of mapping of concentration profiles, mixture homogeneity and suspension velocity. The methods for determining velocity are summarized, since this is of especial interest when applied to opaque systems where most conventional optically based measurements fail. A recent significant development is the use of ultra-high speed measurement that now allows velocity vectors to be extracted for fast moving mixtures and fluids (up to several metres per second). New data are reported pertinent to low and high solids concentration flow in pipelines. Use of the methods offer improvements to design of such systems but also points to the use of tomographic electrical sensor as online flow measurement and fault detection. This offers new opportunities for applications and benefits in the design and monitoring of mineral slurries and sludges.

Jan 1, 2008

A South African gold mining rock-related fatal accident database has been analysed in order to determine rock-related fatality trends in the gold mining industry over the period 1990 to 1998. This analysis was extended further to include some of the individual reefs mined and focused particularly on the Carbon Leader Reef, the Ventersdorp Contact Reef, the Vaal Reef and the Basal Reef. Rock-related accident locations are also presented. A stope rock-related risk is proposed, where the fatality rate in terms of rock-related fatalities per million square metres mined for the gold mining industry as a whole is compared to individual reefs, allowing a stope rock-related risk to be attributed to the individual reef. This comparison is extended further by removing the contribution by the reef being evaluated from the industry data, thereby allowing this reef to be directly compared to the rest of the industry with respect to a stope rock-related risk.

Jan 1, 2001

By M. Soleymani Shishvan

"Continuous mining systems containing multiple excavators producing multiple products of raw materials are highly complex, exhibiting strong interdependency between constituents. Furthermore, random variables govern the system, which causes uncertainty in the supply of raw materials: uncertainty in knowledge about the reserve, the quantity demanded by the customers, and the breakdown of equipment. This paper presents a stochastic-based mine process simulator capturing different sources of uncertainties. It aims to quantify the effect of geological uncertainty and its impacts on the ability to deliver contractually defined quantities and qualities of coal, and on the system efficiency in terms of utilization of major equipment. Two different areas of research are combined: geostatistical simulation for capturing geological uncertainty, and stochastic process simulation to predict the performance and reliability of a large continuous mining system.The process of modelling and simulation in this specific production environment is discussed in detail. Problem specification and a new integrated simulation approach are presented. A case study in a large coal mine is used to demonstrate the impacts and evaluate the results in terms of reaching optimal production control decisions to increase average equipment utilization and control coal quality and quantity. The new approach is expected to lead to more robust decisions, improved efficiencies, and better coal quality management.IntroductionContinuous coal mining systems containing multiple excavators producing multiple products of raw materials are highly complex and exhibit strong interdependencies between constituents. A network of conveyor belts is used for transportation of the extracted materials to different waste dumps or the coal stockpile.Optimal decision-making in short-term planning and production control are impacted mainly by geological uncertainty associated with incomplete knowledge of the coal deposit represented in the reserve block model. These uncertainties cause deviations from expected process performance. For more robust decision-making, understanding the impacts of these stochastic elements plays a key role."

Jan 1, 2016

By Chandrakala Kari, S. Mohan Rao, Gajanan Kapure, K. S. Raju

High carbon ferrochrome production process is energy intensive, consumes approximately 3300-3400 kWh per ton of metal produced. This amounts to ~ 34% of the total ferrochrome production cost. The power costs in India are almost 4 times greater than the leading ferrochrome producing countries like South Africa. Hence there is a need to look for alternative sources of energy. In ferrochrome making process large volumes of high concentration CO gas (~ 85%V) is developed at ~400-5000C, which if combusted within furnace represents high potential for significant electrical energy savings. In a typical heat in the state-of-the-art submerged arc furnace, about 34 kmol of CO gas is generated per ton of ferrochrome metal, which, if post combusted to CO2, represents 7620 MJ of energy. Post combustion of the evolving CO (and H2) gas to CO2 can be achieved by providing additional oxygen before the generated CO gas leaves the furnace. In this paper, a concept of post combustion in submerged arc furnace as potential source of significant electrical energy saving in ferro-chrome making process has been explored. The prospects and limitations of the same are discussed. The value of this paper lies in its attempt to explore the post combustion application to submerged arc furnace with an objective of significant reduction in electrical energy consumption in ferrochrome production process.

Jan 1, 2007