Search Documents

By K. Basaure, S. Palma, R. L. Castro

"Mud rushes are sudden inflows of fine wet ore within underground mines; they can harm people and equipment as well as cause production delays. Block and panel caving mines are prone to mud rushes in their production levels, with mud flowing from the drawpoints. Different mines have developed methods to control drawpoint conditions and thus perform safe ore extraction. The aim of this study is to develop a decision matrix and apply it to samples from drawpoints for the Diablo Regimiento mine, Codelco, El Teniente Division (Chile). The Abrams’s Cone was used to perform slump tests on mud samples and characterize their consistency by setting the saturation degree and packing. The unconfined strength for different saturation degrees and packing was then evaluated. The results show that conditions for fluid response in slump tests correspond to conditions for low strength in unconfined compression tests. We also found the water content value at which the flowing consistency changes from plastic to soft behaviour according to the slump test classification for each sample. This value varied between 12.2% and 16.9%, depending on the sample tested. Finally, a fluid security factor was defined in order to design an extraction pattern for the samples tested, based on the water content. We conclude that a very densely packed ore is not prone to flowing. The flow properties depend strongly on the specific properties of the ore tested, and consequently a specific criterion should be developed for different types of ore at a particular mine. The criterion developed for Diablo Regimiento ore provides critical water content values from 11% to 15%, depending on the ore type. IntroductionBlock/panel caving has the lowest cost and the highest production rates of all underground methods (Heslop, 2000; Hubert et al., 2000). Good management of the risks is important to ensure the security of personnel and infrastructure. Operational risks for the method include rockbursts, air blasts, and mud rushes (Hubert et al. 2000). A mud rush is defined as a sudden inflow of mud from a drawpoint or other underground opening into the mine (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005). Mud rushes can cause dilution, production delays, and damage to equipment as well as injuries and fatalities. The elements necessary for mud rushes are mud-forming material, disturbances, a discharge point, and water (Butcher, Joughin, and Stacey, 2000). All these elements are present in block/panel caving mines. Mud-forming material comes from ore milled by the caving process; water comes from underground and surface sources. Drawpoints in the production level are discharge points for the mud. Finally, several types of disturbance could trigger the mud rush phenomena: blasting, earthquakes, operation of equipment (Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012), arch collapse above drawbells (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Jakubec, Clayton, and Guest, 2012) and ore drawing (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012)."

Jan 1, 2017

By M. Arnesen

Mining professionals recognize the need to continuously evaluate and refine mine planning standards and scheduling. We must examine our current reality, and evaluate the following: •How well do our planning standards represent the actual mining process? •To what extent do they support the requirements of the downstream mining activities? •How we apply them to operational management and control? In most operations, mine-planning standards are global averages. Little differentiation is madein quantifying key planning variables. Often standards used in the long-term, are applied to the short-term, and the standards and scheduling precedents are only reviewed occasionally. Mine-planning standards applied to production schedules are often only focused on the management of functional mining performance, and play no role in managing the requirements of down stream processing. Many mining operations are characterized by high levels of fluctuation, and typically incorporate a wide range of factors and adjustments to compensate for deviations from performance targets, in mining operations as well as for the other business areas. The reason for using global averages is because of a lack of understanding of the causes of deviations that occur through the process, and the impact that they may have on the performance of the business as a whole. Average standards and factors are often used to quantify the variability in a system. From these average values, measurement standards and performance targets are derived for the planning and execution environments. During the execution of a plan/schedule there will be deviation in actual performance and the planned ‘average’ standards. In reality the ‘average’ conditions seldom occur and the impact of variability and interdependency are seldom constant or predictable. The predictability of variability and interdependency is further complicated by the fact that mining conditions have a role to play in the actual production performance, and they too are variable. By developing the throughput knowledge of our production systems, we can better understand the nature of variability and the interdependency within the systems as well as the impact of interdependency between the links in our production chains. With this knowledge, planning standards and scheduling precedents can be better defined and sensibly differentiated. This will improve planning and management of ore utilization, mining production and the effectiveness of processing. As a result the business will be more stable and predictable and business performance will be improved. The purpose of this paper is to describe: •At a high level, the scope for refining and differentiation in mine planning standards, and incorporating geological and plant parameters into mine scheduling. This will improve planning and scheduling and the overall performance of the mine. Given our current level of scientific knowledge and the technological tools at our disposal we should be able to plan and schedule production so that we can manage pro-actively and improve business performance. In doing so we can also improve reconciliation and value tracking through mining and processing •The flexibility and functionality of the XPAC planning and scheduling tool that will enable a throughput management approach.

Jan 1, 2003

By R. McGregor

You wouldn't start excavating before testing core samples, so why would you approve a project plan before all factors have been identified, reviewed and addressed? Even a champion sports team made up of the best players can't produce optimal results without a well understood and agreed game plan. Could an F1 racing team produce their outstanding performance without rigorous evaluation and testing of the factors for successful performance? Why would we expect a capital works project team to be able to get it right without an understanding and an involvement in setting and implementing the overall game plan and without an understanding of all stakeholder requirements? For International Power's Hazelwood (IPRH) mine in Victoria, the challenge was development and delivery of a 40 year mine plan, ultimately involving relocation of existing mine operations into an adjacent new coal field, land acquisitions and major environmental and other approvals to allow diversion of three streams, a highway, an Over Dimension route and other infrastructure in a political and environmentally sensitive atmosphere. The lessons from International Power Hazelwood's (IPRH) experience are: ? that the clear set of project principles and guiding values ensured delivery of a robust plan; ? a robust plan can withstand significant change; and ? value management (VM) played an important role in providing assurance, to all, that the plan was sound at both the strategic and micro levels. This Hazelwood mine project included five major VM workshops. The first was a critical review process in addition to design and cost reviews. This VM workshop was used to analyse, at a high level, the preferred coal mining sequence and design concepts, together with the interaction between design elements, risks and costs. In addition to this, the workshop provided an agreed common pathway for all downstream decisions. A second VM study was conducted to ensure that the proposed plan and design for relocation of the conveying systems from the existing mine into the new field were planned for optimum achievement from a whole of life cost, time, operational and maintenance perspective, plus the logistics of continuing operations while relocating assets. A third study followed to review the Conveyor Transfer Alliance and review functional design. A fourth VM study workshop was formed at the start of Phase 2 Alliance to ensure that the best value for money was being achieved through the current design, schedule and project arrangements and that all interfaces between parties had been reviewed and responsibilities were clear and understood. Other studies are outlined later in this paper. This paper details the evaluation criteria and processes used in the project evaluation that led to the WestField Mine Development.

Jan 1, 2007

By Luis Rudolphy, Pekka Tähkiö

"Flotation plant design, construction and start-up can be challenging tasks, because multiple factors and disciplines have to be combined in an efficient manner, in order to execute a project that meets the technical, financial and timeframe expectations. Key considerations that need to be addressed when designing a flotation plant are process requirements, equipment integrability, automation, and up- and downstream processes/designs. Furthermore, several other lifecycle factors need to be considered, such as servicing and maintainability, operational costs, future expansions and decommissioning, among others. To address these challenges, Outotec has developed a new approach to designing flotation plants that targets eliminating most of the inherent risks that can be found in these types of projects. The new Outotec® plant is a fully modular approach in which the above-mentioned challenges have been taken into consideration in the design phase. As a result, the cPlant concept can give several benefits for new and experienced companies involved in the minerals processing business, such as lower risk investments, fast and cost-efficient flotation plant delivery, faster ramp-up period, easy plant expansions, fully automated processes and operation and maintenance ease. As well, dismantling and transportation of the cPlant to a new location is easy and fast, hence the new cPlant concept makes possible to exploit small, short-lifespan ore deposits and also retreat old tailings ponds that might contain valuable minerals and where the ore quantities are limited. Furthermore, cPlant is easily implemented for brownfields and temporary expansions during bigger expansions."

Jan 1, 2015

By C. Kelley

For years urethane screen surfaces have been used in a wide range of wet screening applications where openings as fine as 75 microns and coarser have been used. In dry screening operations these same urethane screen surfaces have been relegated to only the coarser separation ranging from 1.0 mm and larger. The purpose of this paper is to expose the reader to new developments in both screen surface and screening equipment technologies, which allow an end user to consider urethane screen surfaces for dry screening operations where separations as fine as 75 microns are required. These technologies allow an end user to realize the inherent advantages of urethane in wear resistance while also realizing the benefits that a high open area urethane screen surface can bring. These benefits include non-blinding characteristics and feed capacities, which rival that of traditional stainless-steel woven wire mesh screen surfaces. The paper will highlight the features of this patented urethane screen surface technology and the screening machines in conjunction with which they are used. There will also be a presentation of several case studies of commercial installations where these technologies are utilized. These case studies are from the mineral sands industry; therefore relevance to the conference is direct and not inferred. Included in the paper will also be constraints, which must be taken into account when considering urethane screen surfaces such as temperature and chemical attack. This paper will expose potential end users to a possibility of using screens to achieve extremely accurate size separations in applications where screens were previously not considered. The paper will explain and demonstrate that prior concerns of screen surface blinding, high screen surface consumption rates and large screen surface area requirements can be eliminated by proper utilization of high open area urethane screen surfaces.

Jan 1, 2007

By E. Rex, T. J. Goff, W. S. B. van Beek, P. E. Nel

"The PGM smelting industry is known for operating at significant high superheats. Both the slag and matte phases that separate via gravity need to be tapped out of the furnace in a safe and efficient manner, which can be achieved only through sound tap-hole management practices. This paper gives an overview of the tap-hole management approach followed in the operations at Lonmin’s Western Platinum Smelter.Five circular AC furnaces are operated, with each furnace comprising essentially a crucible and auxiliary equipment. Within the crucible, slag and matte tap-holes are situated at different elevations. The slag phase is tapped at a higher elevation than the matte phase. At the three older furnaces, tapping is done by the conventional method of lancing open the tap-hole and closing it with a dolly. However, at the two newer furnaces, tap-holes are opened and closed with the aid of a drill and mudgun.Tap-hole management can be divided in a number of aspects. In order to achieve a safe opening and closure every time, Lonmin distinguishes between three important aspects - the design of the tap-hole system, the operating practices followed, as well as care and maintenance. This paper briefly describes the tapping channel and cooling requirements for handling superheated matte, together with the difference in design of the matte and slag tap-holes. Mention is also made of the importance of auxiliary equipment, which includes the launders, fume extraction, granulation water, and mudgun and drill units. Improvements made to the matte tapblock design are discussed.The monitoring, alarm, and safety systems related to matte and slag tapping are described. Tap-hole life and different wear mechanisms are mentioned. Tapping can be done safely only if the tap-holes and equipment are maintained properly. Mention is made of the tap-hole refractory repair practices, and the improvements made in order to reduce repair time as well as to extend the time between deep repairs. The importance of the correct tap-hole clay selection in order to nurse the tapping channel after each tap is also discussed.The paper finally touches on some research and development work that was done in order to improve the monitoring of the condition of the tapblock by means of fibre optic temperature sensors"

Jan 1, 2014

By J. A. L. Napier

SYNOPSIS Many tabular mining problems can be modelled effectively by displacement-discontinuity techniques, which can be extended directly to represent fracturing on discrete planes and movements on planes of weakness. This paper presents a unified method for computing the energy changes that occur when multiple discontinuities intersect and are extended incrementally. It shows how this method can be used to deduce energy-release information for standard layout problems and, in addition, how the technique can be incorporated in numerical procedures based on the displacement-discontinuity method. Examples are given to demonstrate the effects of off-reef fracturing and the importance of stope-fault intersections during seismic events.

Jan 1, 1991

By R. G. Votteler, A. C. Brent

"The first in this series of two papers, on the potential of renewable electricity sources for mining operations in South Africa, investigated the internal structure of mining corporations to evaluate feasible alternative electricity sources that were identified as through earlier research. The purpose of this paper is to combine current knowledge about the external macroeconomic and the internal environments to produce a clear picture of how renewable sources of electricity could perform from the perspective of mining corporations in South Africa. The multi-attribute value theory (MAVT) approach was adapted to structure the research and results. The model was fed with real-time data provided from five different energy companies and four mining corporations operating in South Africa. The results show that the performance of hybrid versions of the currently used electricity sources (diesel generators and Eskom grid connection) with solar PV and onshore wind is favourable compared with the current sources alone. The advantage of diesel generators is significantly greater than that of the Eskom grid connection. By combining the macroeconomic influences with the MAVT results, hybrid solar PV versions are identified as having the greatest potential. In second place are hybrid wind solutions, which have the shortcoming that good wind conditions occur only in coastal regions where there are fewer mining activities. Geothermal hybrid versions are the least favourable owing to the lack of service infrastructure and high initial investment costs.IntroductionRecent developments in the macroeconomic environment necessitate an investigation of the internal structure of mining corporations to evaluate possible alternative electricitygenerating sources (Roehrl and Riahi, 2000). To be able to combine current knowledge of macroeconomic factors and the internal structure of mining corporations, the research process is presented in two papers. The first paper (Votteler and Brent, 2016) investigated the internal structure and argued that a strategic tool should be used to evaluate electricity sources from the perspective of mining corporations. The multi-criteria decision analysis (MCDA) approach was selected as the most appropriate strategic tool. Based on a literature review of previous similar MCDA approaches in energy planning, it was concluded that no adaptation of MCDA methods could be found from a corporate, mining, or South African perspective. Finally, the paper investigated the internal evaluation structure in collaboration with mining corporations, by identifying the criteria they use to evaluate electricity sources."

Jan 1, 2017

By J. P. Kirsch

This paper sets out to clearly identify all elements that make up an effective furnace feed system. These are outlined and the more common types of technology are listed. These technologies all play an important role in the final delivery of all feed materials to the furnace.

Jan 1, 2008

By L. Wade

The advent of relatively cheap computing power has precipitated a rapid growth of computer usage in the mining industry. In order to obtain most benefit from this development a need is recognised for the future mining graduate to be trained in computer literacy. This paper outlines the type of training required and describes progress to date with such a programme at the University of the Witwatersrand. Certain challenges concerning the teaching effort are discussed.

Jan 1, 1987

A modified germanium recovery process in conventional zinc metallurgy, based on the understanding that ferric hydroxide has strong ability to coprecipitate germanium element, was presented. The relaxed lab-scale experiments were conducted to evaluate its technological feasibility. The experimental results obtained show the new process has great competitive advantage over the conventional one.

Jan 1, 2008

By J. O. Claassen

A study was initiated and solutions implemented to address the root causes of a 30%?40% lower than predicted product yield achieved at a Mpumalanga coal mine. A holistic MRTM approach, which focused on improving exploration, geological sampling and analysis, geological modelling, planning, mining, and beneficiation practices, was used. The study indicated that deviations in the planned versus actual yields at the DMS plant were caused mainly by incorrect geological yield predictions, high and variable levels of dilution, and near-dense material, as well as the textural properties of the ore. Keywords MRTM, mining value chain improvement, Witbank coalfields, complex geology.

Oct 1, 2013

By R. Gurung, S. Asokan, Ch. V. G. K. Murty, R. Upadhyay

Tata Steel Limited which is Asia?s first and India?s largest integrated private sector steel company, as part of its vision to grow in related industries is also undertaking the Titania project. The project will involve mining, separation of ilmenite and other valuable minerals from the inland heavy mineral sands deposit in the Indian state of Tamil Nadu. The raw material will be beneficiated to synthetic rutile, titanium dioxide pigment and ultimately to titanium metal. The recently concluded feasibility study revealed that the deposit under consideration has 10.4%of total heavy mineral content and 15.2% slimes of the size below 63 µm, over an average sand thickness of 6.9 metres. The presence of about 15% slimes in ROM sand coupled with scarcity of water at the project site complicates the slimes handling/disposal system, requiring the development of an innovative, efficient and effective system for disposal of slimes. Mineral characteristics of slimes revealed the presence of kaolinite clay, which poses its own challenges in thickening/dewatering of slimes. This paper outlines the detailed studies conducted, including slime characterization, settling and thickening characteristics, and ge-technical studies to arrive at an efficient and effective slime handling/disposal system, with a view to plant saplings on the mined-out reclaimed land with species typically suitable to that environment.

Jan 1, 2007

Acid heap leaching has been extensively applied to the processing of copper oxide ores, with recovery of copper by solvent extraction and electrowinning. Heap leaching has also been extended to the treatment of secondary sulphide copper ores, where oxidative conditions are generated in aerated heaps by the bacterially-assisted oxidation of ferrous iron to ferric iron. The treatment of low-grade chalcopyrite ores has recently been the focus of research, with Mintek playing a prominent role. When processing chalcopyrite ores, more complex column test work is performed, which incorporates the prediction and simulation of temperature behaviour in pyrite-containing heaps. Mintek has devised a trade-marked column leaching apparatus (SmartColumn?) for the simulation of the natural temperature profile development in pyrite-containing heaps. As heap leach applications are becoming more complex, the parameters that need to be built into the design and operation of heap leach plants are growing in number, and the amount of data to be collected and processed, and the number of decisions to be taken daily, are also increasing. Mintek has therefore developed the HeapStar® administrative advisory software, as a guidance system to ensure that the correct protocols are implemented at various stages of the leach cycle.

Jan 1, 2012

By J. Manchisi

Laboratory investigations were conducted to establish the feasibility of bioleaching a mixed copper oxide/sulphide rougher concentrate from Nchanga Mine on the Zambian Copperbelt. The objective was to determine the kinetics and extent of copper extraction for this material. Batch experiments were conducted under different solution conditions in stirred tank bioreactors. The progress of (bio)leaching was monitored through measurements of soluble ferrous and ferric iron, copper, pH, and redox potentials, while bacterial activity was monitored online through 02 and C02 gas utilization rates. About 20 per cent copper was solubilized within 2 hours in all cases of non-oxidative (abiotic), oxidative (abiotic), and bioleaching experiments. This was attributed to the dissolution of mainly copper oxides. Subsequently, bioleaching experiments resulted in an overall copper extraction of 93 per cent, with up to 8 g.L-1 copper after six leaching days, compared to 58 per cent copper extraction in the abiotic oxidative acid leaching experiments. However, there was little effect of time (i.e. poor dissolution kinetics) on copper recovery for abiotic non-oxidative acid leaching of the material. Hence, the rate of sulphide leaching increased due to the activity of bacteria. Thus, the material is potentially bioleachable under mesophilic conditions. However, more exhaustive test work needs to be conducted to establish the effect of bioleaching variables and heat requirement.

Jan 1, 2012

By K. A. Annan

The last seven hot rolling passes of the ferritic stainless steel AISI430 were simulated on a Gleeble-1500D® thermo-mechanical simulator to investigate the effect of temperature, strain rate, and interpass time on the texture. The compression tests were carried out over a wide range of strain rates (0.1 s-1 to 5 s-1) and temperatures (1100°C to 820°C) with different interpass times (2, 10, 20, and 30 seconds). The dynamic recrystallization to dynamic recovery transition temperature was determined from examining the relationship between the mean flow stress and the inverse of the deformation temperature in multi-pass tests. It was found that the texture in the central layer of the compressed sample is a strong recrystallization-type. The through-thickness textural and microstructural banding, to a large extent, were found to be weakened by hot deformation in the two-phase (a+ ?) region, as opposed to the single-phase (a) region.

Jan 1, 2013

By G. R. Lane

A large opencast gold mining company in Africa had just completed a feasibility study for the expansion of the operations. A traditional net present value project valuation methodology had been used that showed a very positive net present value (NPV). The project team had conducted a qualitative risk assessment that identified and logged all potential project risks and had subjectively incorporated ?risk? via the discount rate and other assumption contingencies around gold price expectations, operating parameters etc. Management requested that an independent quantitative risk modelling approach be adopted to obtain a better understanding of the impact of risk on the overall project valuation and confidence level in the final valuation. A detailed project valuation model was configured in the Carbon Modelling Technology and the stochastic modelling module used to perform the Monte Carlo simulations. Analysis of historical operational performance data relating to actual achievements versus planned and budget determined the historical variability of the underlying parameters as well as variance to budget. This was done at a detailed level for mining rates and costs, processing rate, costs and recovery, and other operational efficiency measures. External market assumptions relating to gold price, exchange rate, and inflation were modelled and the dependency between them modelled using a copula. This case study will demonstrate the approach taken to building and populating the quantitative risk model and the overall results of the Monte Carlo simulation. The final valuation demonstrated that the project had a 44 percent probability of an NPV less than zero i.e. 44 percent chance of project finance loss.

Jan 1, 2012

By G-L. Wu, X-B. Liu, C-Y. Zhou

"The static recrystallization behaviour of Ti-Nb microalloyed high-strength steel during hot deformation was studied by conducting double-hit hot compression experiments using a Gleeble-3500 thermomechanical simulator. The effects of deformation temperature, strain rate, strain, and initial austenite grain size on the static recrystallization fraction are discussed. The static recrystallization kinetics were modelled, and the results show that the static recrystallization fraction increased with deformation temperature, strain rate, and strain and interpass time. The static recrystallization activation energy Qs was 326.05 kJ mol-1. Comparison of the experimental results and predicted results indicates that the effects of deformation parameters on the static recrystallization in multistage hot deformation are significant. The predicted results are in good agreement with the experimental results. IntroductionIn hot-forming processes, complex microstructures are often induced by multiple hot deformation mechanisms (Zhang et al., 2014; Liang et al., 2015). The softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by the corresponding microstructural evolution (Wu et al., 2010). It is well known that dynamic recrystallization (DRX); metadynamic recrystallization (MDRX), which occurs by the growth of DRX nuclei during intervals of deformation; and static recrystallization (SRX), which occurs by nucleation and growth during the intervals of deformation, can significantly alter the austenite grain size (Chen et al., 2015. Chen, Sui, and Cui, 2014; Mao et al., 2014). The long interpass times allow complete SRX to take place if the steel is being rolled above the interpass recrystallization stop temperature (Tnr), i.e. in the absence of carbonitride precipitation (Siciliano, 2000). In recent research, microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient in achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Bandyopadhyay et al., 2011). The alloying elements Nb, V, Ti are widely used in high-strength low-alloy (HSLA) steel to achieve the desired strength and toughness properties with solid-solution strengthening, precipitation hardening, grain refinement, and dislocation strengthening (Opiela, 2014; Chen and Yu, 2012). The wide applicability of alloying elements in HSLA steel is due to the fact that heat treatments are not required after forming of the parts, which results in time and cost savings."

Jan 1, 2017

By F. Bourgouin

Thirty-one years ago, African leaders met in Lagos for the drafting of the Lagos Plan of Action for the Economic Development of Africa, 1980?2000. The main objective of the plan was to increase Africa?s self-sufficiency and in this regard, the plan had a section pertaining specifically to redressing the ills of an unproductive mining and minerals industry and harnessing its potential for socio-economic development. However, if we look at the nature of this sector on the continent today, its characteristics resemble the diagnosis of the sector given in the plan back in 1980: lack of information on endowments of minerals; lack of value added in the sector; low development and use of those endowments that are not of interest to transnational corporations (TNCs); and most importantly, low contribution to socio-economic development. The primary consequence of the lack of visible benefits to African states, despite growth and development of the sector in terms of increased mining activity led by Foreign Direct Investment is that countries with mining industries are characterized by dysfunctional internal processes. Improvements in governance, monitored with indices such as those set out in the Extractive Industries Transparency Initiative, the Millennium Development Goals, and other such ?good governance? agendas, are being asserted. However, before we prescribe the introduction of initiatives or guidelines based upon highly subjective norms which we believe to fit this diagnosis, it is necessary to review how it is that we got to this situation that we are in today. How is it that, 31 years after the Lagos Plan of Action, we have not seen any major changes in the role the industry can play in socio-economic development, despite the vast increase in mining activity on the continent?

Jan 1, 2011

By N. K. Singh

The calculation of resource volumes for large mineral sands deposits is the process of systematically compiling all known data in order to define the volume of ore contained and its intrinsic economic value. Traditionally, this process has been highly speculative in nature, as the variability of the layer thickness, even between closely spaced, boreholes can be highly variable. The issue of horizon continuity is of critical importance in mine modelling and resource definition. Accurate volume estimates are difficult to derive from drilling data alone, as the borehole spacing of an economically viable drilling programme is often greater than the spatial frequency of the variations in profile thickness. The limitations associated with this inferential approach to resource estimation can be mitigated through the use of newly developed ground penetrating radar (GPR) methods, thereby maximizing orebody optimization by reducing contamination and orebody loss. The use of GPR in the mining industry has historically been limited to shallow, high-resolution applications, such as the location of voids in limestone or the mapping of paleo channels for alluvial gold and diamonds (Francke and Yelf, 2003). These limitations have not been technology based, but rather market based, as the vast majority of GPR systems were originally designed for civil engineering applications. A new generation of GPR technology, designed specifically for maximum penetration in sand environments, is now being developed. This technology has been trialled extensively at the Richards Bay Minerals heavy mineral sand deposit in South Africa with optimistic results. The clay base of the mineral sands has been imaged to some 120 metres. Further equipment refinements are expected to yield even deeper profiling and higher resolution. The resolution offered by this technology is unique, allowing individual depositional sequences to be imaged and modelled in three dimensions. This paper will discuss the advances in GPR technology relevant to the mineral sands industry, as well as methods to optimize and integrate GPR data into existing mine models. Also addressed will be approaches to three-dimensional modelling of high-resolution GPR data and subsequent volume estimations.

Jan 1, 2007