Search Documents

Reduce face methane concentrations and help prevent miners from working under unsupported roof while moving the curtain. Approach Use water sprays on the continuous mining machine to move and direct air to the face, and also provide appropriate installation guidelines for the most effective use of the system. I n laboratory tests and under actual mining conditions, the spray fan has proved an effective means of ventilation. Recent observations in the field, however, have shown that not enough technical information is widely available on proper installation of the spray fan. This Technology News is designed to rectify that situation by providing a concise guide for spray fan installation. How the System Works Good ventilation is essential for methane control. The spray fan system repositions regular water sprays to help the normal exhaust face ventilation do a more effective job. The various water sprays help in many ways: 1. Side sprays bring clean air along the side of the miner into the off-curtain corner.

Jan 1, 1983

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974

By William C. Laubengayer, Robert R. Godard, Harry Dobroski

A whole mine, computer-controlled communication and monitoring system for both normal and emergency use is installed and operating in the U.S. Steel Robena Mine complex near Uniontown, Pa. Portions of the system, including the coaxial cable and the key underground and surf ace phones, have been operating for over a year and a half. During this time the basic concept has been modified and new line amplifiers with directional switches have been developed to eliminate some problems in implementing the loopback feature. The quality of the audio and the availability of the system have been outstanding. Since early summer almost all subsystems have been completed. The experience with the telephone system itself, the pocket-pager call alert, section wireless radio, hoistphone, television, environmental monitoring, control and monitoring of equipment, voicedownlink/code uplink post disaster communications, post disaster through-the-earth monitoring, and the system center failure diagnostic routines are reviewed.

By J. H. Russell

As part of its efforts to maximize resource recovery, the Bureau of Mines conducted studies to recover valuable byproducts from Western phosphate beneficiation tailings. Potential byproducts include phosphorus, vanadium, and uranium. The objective was to determine roasting and leaching conditions for maximum dissolution of vanadium from tailings containing approximately 13 pct P205 and 0.23 pct V. Sulfuric acid leaching tests were conducted with the tailings either as a dilute suspension dried, or in a roasted condition with or without NaCl added during roasting. More than 90 pct of the vanadium was dissolved by roasting at 850° C for 120 min with 8-pct NaCl and leaching at 75°C for 120 min with an excess of 2N H2S04, By roasting without NaCl and avoiding the difficulties of the chloride impurity, nearly 80-pct vanadium dissolution was achieved with an 800° C roast for 180 min. Quadratic regression equations were derived to relate vanadium dissolution to roasting and leaching conditions.

Jan 1, 1982

Improve face ventilation in mines with large cross-sectional entries. Approach Oil shale, salt, and limestone mines typically have large entries. Providing adequate airflow to the working faces of such mines for worker comfort, health, and safety is a substantial ventilation problem. If diesel equipment is used at the face or if a methane hazard exists in the mine, the problem becomes even more complex. To address this problem, a study was conducted under a joint contract between the Oil Shale Committee of the Colorado Mining Association and the Bureau of Mines. The study evaluated two face-ventilation concepts for large-entry mines. Improving Ventilation Two face-ventilation systems were selected for testing of an oil-shale mine, based on results of a cost/benefit analysis. The systems were a free-standing jet fan and a ducted fan operating in the blowing mode. The jet fan was spotted on the intake side in the mouth of the entry being advanced with final positioning, in or out, deter-mined by minimum recirculation. The ducted fan was also positioned in the mouth of the entry being advanced, with its tubing terminating 75 feet from the working face. The mine face entry was a dead heading 55 feet wide, 30 feet high, and 320 feet long. Sulfur hexafluoride (SF.) tracer gas was used to measure the performance of the two systems in diluting mine face pollutants including after-gases from blasting, hot diesel emissions, methane roof layers, and methane emitted from muckpiles.

Jan 1, 1987

By Larry G. Stolarczyk

1.0 FRAMEWORK FOR COMPARISON This document describes the decision factors that bear on the selection of the modulation process for the wireless underground medium frequency (MF) communication system. The selected modulation process must satisfy the Bureau of Mines stated objective of improving general communications within an underground mine. The improvement being sought includes the development of a wireless communication technology of measurable benefit to both mine safety and mine productivity. The improvement will allow wireless communications paths to exist between roving miners. The wireless communication paths will also be made compatible with the existing underground telephone system to extend paging and voice communication throughout the underground mine. The new wireless equipment will include man-pack, vehicular, repeater, and base station transceivers. Repeaters and base stations will feature coupling networks for interfacing with the existing telephone circuits. Frequency modulation (FM) and single sideband (SSB) modulation processes are analyzed in view of the special conditions associated with underground mining. Of primary importance is the tremendous electrical noise generated in an operating mine that could adversely affect communications quality. High noise coupled with high attenuation rate of near field signals forces the communication system to be inherently short range. Fortunately, near field signals can propagate over great distances on underground wires and cables. The framework for comparison is generated by presenting all factors that

By T. W. Beck

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter’s dust collection system. The laboratory tests evaluated the bag’s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector’s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector’s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

By Todd M. Ruff

The lack of visibility near earthmoving equipment resulted in six fatalities in U.S. surface mining operations during 2003. These accidents were the result of either a piece of equipment striking another vehicle or worker, or the equipment traveling over the edge of an embankment. Figure 1 is an example of a recent accident that resulted in serious injuries to one worker and fatal injuries to two others when a van parked in front of a haul truck. Two fatalities occurred in separate incidents when front-end loaders struck workers. Another two workers were killed when their equipment backed over the edge of a highwall or dump point [1]. There is clearly a need to provide better information to equipment operators regarding their surroundings. [ ] Researchers at the National Institute for Occupational Safety and Health (NIOSH), Spokane Research Laboratory, are working to reduce these accidents by developing systems that sense obstacles and changes in terrain near the equipment and provide this information to the operator. Many off-the-shelf proximity warning systems that were developed for automobiles, light trucks, and recreational vehicles were evaluated on off-highway dump trucks [2]. Many limitations were found with existing systems, including frequent false alarms, limited detection range, a lack of specific information on an obstacle (e.g., location, identity), difficulties in finding suitable mounting locations, and an inability to withstand the environment. These limitations have necessitated the development of new systems designed specifically for large, off-highway, earthmoving equipment. New off-the-shelf systems available for mining equipment include radar and tag-based detection systems. Prototype systems now being developed include a proximity warning system based on the Global Positioning System (GPS) and a computer-assisted stereovision system. Development of these new systems was accomplished by working with manufacturers to modify existing systems to meet the needs of surface mining and through cooperative research with organizations to develop completely new solutions. A typical proximity warning system consists of a sensor or antenna mounted on the equipment that detects the presence of obstacles and an alarm interface in the cab of the equipment. Some systems, as described in more detail below, also require that other vehicles and personnel on the ground be outfitted with electronic tags that transmit an “I’m here” signal back to the system (e.g., radio signal detection systems or GPS). Many types of proximity warning systems are on the market, but they are not all discussed in this paper. APPROACH In past work, engineers at NIOSH evaluated several off-the-shelf proximity warning technologies in order to verify their effectiveness on off-highway dump trucks [2]. Dump trucks were chosen because of the number and severity of accidents involving this type of equipment and because extensive blind areas around these trucks are typical. This experience allowed engineers to limit the number of systems chosen for long-term tests at mine sites to those systems showing

By Harry F. Weaver

Rivers in industrial and raining areas frequently are contaminated by material dumped into them causing the water to carry in suspension large amounts of silt, which subsequently is deposited alone; the banks and, ultimately on the agricultural lands if the water is used for irrigation purposes. Two common examples of this practice are the dumping of breaker refuse in the anthracite region of Pennsylvania and the dumping of tailings from the metallurgical mills in various metal-mining districts. Studies in stream pollution and its resultant problems are very important, and surveys are constantly being made by Federal and State agencies, as well as by private companies, to determine the quantity of solids actually being carried by these watercoarses. These studies require accurate sampling of the silt-carrying water to determine the amount of solids within reasonable limits. A device that will obtain reasonably accurate samples of material from silt-bearing streams is described in this circular.

Jan 1, 1943

Reduce the dust exposure to the operator of a longwall shearer with a novel foam spray system. Approach Discharge foam through the nozzles of a shearer drum so that foam and coal are better mixed. How It Works Bureau of Mines research showed that two very important principles for successful application of foam are: (1) moisture distribution and (2) degree of mixing. Foam can distribute a given quantity of moisture much more evenly over a large surface area. Successful Bureau tests of foam for dust control always involve a high degree of mixing between the foam and the material, Mixing, permits a greater distribution of foam throughout the mined product. The most suitable location of foam application would be at the point where the dust is generated, before the dust becomes airborne. Foam nozzles located in the cutter drum (pick face foaming or ejecting foam through scroll sprays) will suppress dust close to its source.

Jan 1, 1989

By F. M. Carlson

Comparisons are made between the results of the Buckley-Leverett and Kern solutions, which describe immiscible displacement of oil by gas in a linear system and the results obtained from a less restrictive numerical model. This model takes into account the effect of compressibility of the oil and gas and the effect of allowing changes in the amount of gas in solution in the oil. These effects are best exemplified by imposing large pressure drops across the system. With these large pressure drops, comparison of the model solution with the Buckley-Leverett solution reveals that the Buckley-Leverett solution provides estimates of recoveries at breakthrough of the gas that are too low. In contrast to the model, the Kern solution predicts breakthrough recoveries that are too high. A modification to the Kern solution is presented to facilitate more accurate predictions of recovery at gas breakthrough for gas injection at pressures higher than the saturation pressure of the oil.

Jan 1, 1974

Provide a means of evaluating the in place structural properties of coal seams and coal measure rocks in advance of mining. Approach Develop a sonic logging probe for use in dry wells, a condition common to shallow wells and semi-arid coal regions. How It Works The Bureaus' sonic probe differs from conventional sonic probes because it does not require fluid in the well to couple sonic vibrations to the drill hole wall. A self-contained hydraulic system forces pistons containing the measurement transducers against the wall and clamps them in position until the sonic waveform information has been recorded. The pistons are then retracted and the probe is raised or lowered in the well as required. In the clamped position, the piezoceramic transmitter emits a sonic pulse which travels along the drill hole wall and is detected at the receivers in the form of compressional (P) and shear (S) wave motion. The receivers are designed to be sensitive to either the (P) wave or (S) wave motion as determined by the operator so that discrimination between the two wave types is improved by comparison of the respective output channels, and the travel time between transmitter and detectors can be accurately determined. Use of two receiver stations eliminates errors in timing of pulse travel because of electronic delays inherent in the probe.

Jan 1, 1981

By R. R. Sayers

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try , if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

Develop a metal substitute which is more plentiful and less expensive than the metals currently being used in high performance, permanent magnets, while maintaining the quality of the magnet. The New Alloy The rare-earth metal used in most high performance magnets is samarium, an expensive metal of limited availability. Cobalt is also used in high performance magnets, but supplies of this metal also are limited because it is not domestically mined and must be imported. The Bureau of Mines embarked on research to find a less costly domestic: metal source for use in industrial magnets. The alloy found most promising consists of mischmetal, a relatively abundant, naturally occurring mixture of rare-earths, which can be used as a replacement for samarium. Additives of copper, magnesium and iron used in combination with mischmetal aid in replacing some of the cobalt needed for the magnets.

Jan 1, 1983

By Donald W. Fausett

This Bureau of Mines publication presents a system of thermal decompositions providing an adequate description of the mechanism of oil shale pyrolysis. Specific rate constants for systems of thermal decompositions studied are estimated via a least-squares procedure. The estimates thus obtained provide a mathematical model of the corresponding thermal decomposition system. A model that generates a good fit to published Bureau of Mines experimental data, in comparison with other models studied, is based on a thermal decomposition system consisting of two first-order reactions and three second-order reactions. Values computed for the specific rate constants corresponding to this system are shown to exhibit a temperature dependence that is in good agreement with the Arrhenius equation.

Jan 1, 1974

By F. W. Penn

An aircraft auxiliary power unit (APU) was used as an exhaust source for evaluation and refinement of sampling and analytical procedures for gas turbine engines. The unit was also used to determine the emission characteristics of APU's in service and to study the effect of fuel composition and combustor design on exhaust emissions. Carbon monoxide, carbon dioxide, oxides of nitrogen, hydrocarbons, aldehydes, particulate loading, and odor were measured at engine operating modes representing the duty cycle encountered in airline operation. Analyses showed good repeatability, and adequate sensitivity was attained in these experiments. Smoke opacity measurements were not taken owing to the lack of a high-sensitivity smokemeter. Results showed that the minimum emission levels occurred with the standard combustor and Jet A fuel. Emission rates were highly dependent on test mode, but emission patterns as a function of test mode were similar for all fuels and combustors tested. A comparison of three identical design production combustors showed a variation in average emission rates of less than 5 pct.

Jan 1, 1973

"""Hazard"" is the general expression used by safety engineers to denote risk, or the danger to property or human beings from the contingencies peculiar to different industries. Where a business, family, or individual is subjected to possible financial loss from any particular hazard, it is customary and is considered good practice to insure for reimbursement of possible loss. Accordingly, we take out insurance for earthquakes, for fire, for accidents, etc., and are charged a different premium for each. The premium rate is based on our relative exposure to the hazard in comparison to the total loss to our particular class of business in our geographical location over a given period.Insurance, then, must be considered as the experience of a group rather than of an individual, and any individual may be fortunate or unfortunate over stated periods. Through the law of averages, the probability of loss because of exposure to hazard is becoming more accurately measured as experience is accumulated and data are analyzed.Lion human life came to have a financial value in the eyes of the law, and employers were held liable for losses through accidents to employees while on duty, insurance companies began to underwrite the accident risks of the different employers and divided them into classes based on the amount of risk involved. Premiums for compensation insurance are based on relative exposure, which is measured by pay roll. The premium is rated in proportion to the severity of losses established by statistical studies.' It soon became evident that the accident experience of employers in the some industry varied widely; that is, there were good and bad risked in the same line of business. This resulted in ""experience rating"" of premiums, meaning thereby that an employer with experience in accident cost was premium rated in proportion to his losses over a stated period (usually three or more years)."

Feb 1, 1926

By Dorsey A. Lyon

At the main experiment station of the U. S. Bureau of Mines , situated in Pittsburgh, Pa . , three phases of its work in behalf of the safety of the coal miner are the establishment of permissible explosives for use in gaseous and dusty mines , the development of electrical equipment that can be used with safety in mines of this character , and improvement in the safety of mechanical devices used in and about the mines . Also That these efforts are beginning to have a cumulative effect in lives. saved is evident from the fatality statistics of the industry . Although nearly 80,000 more men are employed in coal mining than ten years ago and much more coal is mined , the fatalities each year are considerably less than ten years ago . the amount of coal mined in a year for each life lost has risen between 60,000 and 70,000 tons . In 1909 , the year before the Bureau was created , the production of coal for each life lost was 174,416 tons . In 1920 , the production for each life lost was 285,000 tons .

Mar 1, 1921

By E. J. Gleim

Many people consider the mining of coal to be an extremely hazardous occupation; but it should be remembered that most large industries have to meet special conditions which, if not dealt with properly, might become hazards to life and property. Mining men may not always be fully aware that some practices and certain equipment that is incorrectly designed or maintained can lead to dangerous conditions. In endeavoring to help the coal-mining industry to prevent accidents and disasters, the Bureau of Mines has engaged in a program of education on conditions and practices that must be avoided. An effective way to teach safety is by visual demonstration. For example, it is generally known that certain kinds of electrical flashes have ignited explosive atmospheres in mines, but actually to see and hear explosions caused by electrical sparks of different size and character under laboratory control is likely to teach a much more emphatic and lasting lesson than would be learned by merely reading about them. The interest manifested by those who witness the demonstrations seems to prove that this is true. The purpose of the demonstrations is not to discourage the use of electricity in mines, but rather to indicate what types of equipment (including some generally regarded as harmless) can ignite gas and what safeguards have been developed to prevent such ignitions. It is hoped that this information will improve the ability of mining men to cope with underground hazards.

Jan 1, 1937

By J. M. Stuve

Heat of solution measurements of high-purity neodymium metal and neodymium trichloride (NdCls) in 4.360 molal hydrochloric acid (HCI) were used to determine the standard heat of formation (6EPr) of NdCls? From solution data obtained, the heat of formation of NdCls (c) was computed as -248,970 ±260 cal/mole at 298.150 K.

Jan 1, 1965