Search Documents

Develop a method for recovering phosphate from a wide variety of complex western phosphate materials, including low-grade ores, tailings, and unused fines. Approach A flotation technique is used for this broad type of extraction. The method includes depression of phosphate minerals and anionic flotation of carbonate minerals, followed by cationic flotation of silicate minerals. How It Works A slurry is prepared for flotation by sizing to remove a low-grade, high-impurity slime fraction. Depending on the material, further sizing and/or grinding steps may be used to produce a size concentrate or to remove gangue. The flotation feed is conditioned with H2SiF6 and a fatty acid emulsion. The H2SiF6 is absorbed chemically to the phosphate mineral surface, making it strongly attracted to water and preventing adsorption of the fatty acid. Under these conditions, the fatty acid is a selective collector for carbonate minerals, which are removed as a froth product. Next, the silicates are floated with an amine reagent added directly to the slurry without additional pulp preparation.

Jan 1, 1982

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

By John Gross

The modern practice of grinding ores so that often 80 per cent or more of the product is finer than 200 mesh makes it desirable to supplement sieve sizing so as to extend considerably the range of sizing. Moreover, the fact that the material finer than sieve size represents the major part of the work done in grinding emphasizes thick need in can investigation of crushing efficiency. A method based on the settling rate of particles in grater appeared to be most practical for sizing; finely ground ores. There are two possible methods of utilizing this principle: one based on free settling or sedimentation; and the other on separation by means of a rising; current of water, or elutriation. In sedimentation, mechanical entanglement causes material at the start to settle in a mass, and this persists throughout. As this feature is largely eliminated by elutriation, which permits a comparatively clean separation of the various sizes, the elutriation method was adopted.

Jan 1, 1929

By Thomas M. Barczak

This report describes a study that examined load transfer mechanics in longwall shield supports as part of the Bureau of Mines research program to optimize support design and utilization. The objectives of this study were to determine the contribution of the leg cylinders and the caving shield-lemniscate assembly towards full shield vertical and hor-izontal load resistance capability and to determine how the interaction of these members affect overall shield response. Load-displacement characteristics of the leg cylinders and the caving shield-lemniscate assembly, independent of the full shield, were evaluated from controlled displacement tests in the Bureau's mine roof simulator and responses were compared with full shield responses to identify load transfer mechanics. It is concluded from this research that the participation of the caving shield-lemniscate assembly significantly affects the response of the shield support. It is likely that the caving shield-lemniscate assembly is not participating fully in current shield designs because of translational freedom in the numerous pin joints. It is also concluded that the shield will respond differently to different boundary condi-tions resulting from interaction with the strata. This report describes load transfer mechanics of shield supports and the implication of these research findings on shield design and utilization.

Jan 1, 1988

By William D. Mayercheck, August J. Kwitowski, John R. Bartels

This report discusses the Bureau of Mines' efforts to develop partial protective structures for operators of low-coal shuttle cars. In coal seams 48 in high or less, full-coverage canopies are generally difficult or may be impossible to implement on high-speed face equipment due to the restrictions they impose on the operator's vision and comfort. Lim- ited coverage is one alternative that provides an acceptable level of operator protection in thin-seam applications where conventional full- coverage canopies cannot be used. Three possible limited-coverage de- sign scenarios (roll bars, sliding canopies, and flip-top canopies) were designed, fabricated, and evaluated for low-coal shuttle cars. All three designs were determined to be feasible and desirable for low-coal shuttle car application.

Jan 1, 1987

By W. Hermanson

This report, which covers the period from January 16 to October 21, 1974, describes the work performed in compliance with the requirements of contract no. H0242028 and modifications 1 and 2 thereto. The purpose of the contract was to further reline and modify three of the canopies (shuttle car, loader, and roof drill) which were developed under contract no. H0220031, and to conduct further testing and demonstration of the relined designs. Modifications I and 2 involved conducting further in-mine evaluations of the face. drill and cutter canopies, also developed under contract no. H0220031. In addition to the canopy modifications, the contract involved an evaluation of an operator's seat concept for a shuttle car which was developed for the USBM by another contractor.

Jan 1, 1974

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By Alfred E. Schwaneke

A versatile torsion creep tester was instrumented with electromechanical and servomechanical components to operate automatically and unattended, producing digital printed outputs. The apparatus uses an electrical system for applying torsional stresses, and a unique angular transducer as a null detector operating a servocontrolled strain measuring system with the digital readout. The tester is designed to measure the creep in single-crystal or polycrystalline zinc, zinc alloys, magnesium, magnesium alloys, or other metals and alloys. Applied stresses may be varied from zero up to 2,000 psi in the outermost fibers of a 1/8-inch-diameter, 4-inch-long specimen. Strain readings to 0.001 degree, equivalent to a strain of 2.73 X 10-7, may be made automatically from one every 5 seconds to one per month. The apparatus has provisions for programed temperature control and special atmospheres or vacuum operation. A discussion of applications of the system to other mechanical testing apparatus is included.

Jan 1, 1970

[ ]

Jan 1, 2011

By Edward A. Mihok

This paper presents plant design and cost estimates for limestone treatment of acid mine water covering a wide range of quality and quantity conditions. The treatment process consists of limestone neutralization, aeration, solids settling, and concentration. The design criteria for the various operation functions are based on pilot plant performance, laboratory data, and established mine water treatment standards. Unit costs have been assumed and are related to general market prices and conditions. These estimates serve as preliminary indicators of what it would cost to construct and operate a mine water treatment plant.

Jan 1, 1970

By Lucia Kuizon

Results of the U.S. Bureau of Mines&apos; survey of mineral resources in the Cuyama RARE II study area indicate there is no potential for metallic minerals and low potential for the development of gypsum resources. There are no producing or developing mines within the study area. The Santa Barbara Canyon Prospect contains 30,000 tons (27,000 t) of subeconmic gyspum resources, the Wagon Road Prospect 276,000 tons (250,000 t), and the Brush Fence Canyon 61,000 tons (55,000 t). Most of the resource in the Brush Fence Canyon Prospect is outside the area. Gypsum was not observed at the Cuyama River deposit. Present gypsum and gypsite requirements are being met by larger deposits closer to major markets. INTRODUCTION Location (USGS) Present and Previous Studies (to be combined with USGS section) The Bureau of Mines reviewed literature and mining claim records for the study area. A field examination of known mineral properties was made in October 1980; it included mapping and sampling of prospects to evaluate the economic potential of mineral resources.

Jan 1, 1981

By E. K. Stanek, P. Kantabutra, R. A. Wolf

This paper summarizes the cause and effect of induced voltages in multiple conductor cables supplying alternating current power to equipment in under- ground coal mines. The investigation of this phenomenon revealed that the electrical energy produced by the resultant electric arcing between the frames of mobile electric face equipment was of a sufficient magnitude to ignite explosive methane-air mixtures. The results of laboratory tests and field tests made between equipment frames during actual operation in numerous coal mines are discussed. Several methods of eliminating or suppressing the induced voltages to nonincendive levels are also described. It is the purpose of this paper to convey to the mining industry a knowledge of this problem and to recommend methods of eliminating or reducing these induced voltages or arcing currents to safe levels.

Jan 1, 1975

Enhance hydraulic fragmentation technology by developing alternative grout sealing methods. Traditional grout scaling methods rely on chemical adhesion and require large contact areas to restrict high-pressure fluids. Fluid injection into rock requires economical and effective seals. With economical and effective seals, rock is easily fractured in tension by high-pressure fluid injection (fig. 1). Approach An innovative grouting technique was developed and tested by the Bureau. Slowly hydrating expanding chemicals are placed within a borehole and around a section of high-pressure tubing. Testing was conducted using 9/16-inch-OD smooth-walled injection tubes in 1.5-inch-ID holes. Seal lengths weir less than 10 inches and curing times were less than 24 hours.

Jan 1, 1989

By Kevin Michael, David C. Byrne

In previous issue of Spectrum (October 1999, 16/4), a system of measuring the attenuation provided by insert-type hearing protectors was described, That report described experiences using the FitCheck (Michael & Associates, Inc.) system in a pilot project involving the steel industry during 1998.[ ]

By Charles P. Lazzara, Charles D. Litton, Frank J. Perzak

This U.S. Bureau of Mines report details the results of a series of large-scale experiments where small coal fires were used to ignite the conveyor belt at air velocities ranging from 0.76 to 6.1 m/s. In the tests, electrical strip heaters imbedded within a pile of coal were used to heat the coal to a point of flaming ignition. The flaming coal subsequently ignited the conveyor belt located approximately 5 to 10 cm above the coal pile. During the tests, temperature, CO, and smoke levels were continuously measured in order to determine both alarm time and level as the fire intensity progressed through the stages of smoldering coal, flaming coal, and flaming coal plus flaming belt. Analysis of the data leads to certain conditions of air velocity and sensor alarm levels that are required for early detection of conveyor belt entry fires. Two nomographs are presented, which define sensor alarm levels and sensor spacings as a function of belt entry cross-sectional area and belt entry air velocity.

Jan 1, 1991

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface metal/nonmetal mining categories during 1990–2001 by state and six successive 2-year time periods. Injury risk rates are derived, and ignition source, methods of detection and suppression, and other variables are examined. Fires involving contractors are also included in the analysis. The data were derived from Mine Safety and Health Administration (MSHA)mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and an increased awareness aimed at preventing and reducing fire hazards. It will also form a basis for future fire research programs.

Jan 11, 2004

By A. May

Florida has accumulated about 400 million tons of phosphogypsum, a mineral process waste generated in the production of fertilizer, and is adding 30 million tons to this annually. To minimize storage of this waste and reduce potential environmental effects, the Bureau of Mines conducted research into utilizing the phosphogypsum, by identifying and developing high-volume uses for this material. Admixtures of phosphogypsum, fly ash, and lime that could produce a coarse aggregate suitable for road construction were investigated. Using phosphogypsum with asphalt, cement, cement-kiln dust, silica, clays, and oxychlorides to pro-duce aggregate was also examined.

Jan 1, 1985

Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During 1996-99, 44 coal miners lost their lives in rock falls, and nearly 2,400 were injured. In addition, nearly 6,000 noninjury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH). The purpose of these proceedings is to provide the mining community with a comprehensive survey of coal mine roof supports. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, this volume describes what types of support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, material handling considerations, and longwall mining through recovery rooms. This proceedings volume also contains information on several important new technologies, which are described here for the first time: •Guidelines for selecting roof bolt length, pattern, and capacity that were derived from statistical analysis of the roof fall experience at 37 underground mines; •A new design method for longwall tailgate supports; and •A technique for measuring loads developed within cable bolts. The papers in these proceedings were presented at open industry briefings conducted by NIOSH on New Technology for Coal Mine Roof Support. The briefings were held in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. The papers were also presented at the Mine Safety and Health Administration (MSHA) Preventative Roof-Rib Outreach Program (PROP) Seminar, which was held at the National Mine Health and Safety Academy near Beckley, WV.

Jan 10, 2000

By Kevin Connor

The mineral industry continued to be an almost negligible contributor to the country&apos;s economy as the Government continued its 1979 ban on any mineral exploitation for export; a policy initiated at the end of 1979. A national program had been underway since that time to map and inventory all mineral resources so as to permit future exploitation of mineral wealth in the beat interests of the country and its inhabitants. In March 1982, the British Sulphur Corp. Ltd., under contract to the Burundi Government and the International Bank for Reconstruction and Development (World Bank), began a feasibility study of Burundi&apos;s phosphate deposits at Matongo-Bandaga for potential commercial exploitation. The 1-year project effort was to define ore reserves, conceptually design mining operations and processing facilities, estimate capital and production cost, and develop a regional market and distribution survey. Work completed during the year comprised geological exploration and reconnaissance and 1,200 meters of core drilling. Reserves in excess of 5 million tons of ore-grade phosphate were estimated available for mining. Rare earth mineralization was associated with the primary apatite. The associated carbonatite within the rock matrix was preliminarily assessed to be of value as a raw material for the manufacture of cement. The contract effort was valued at $1.2 million? Matongo-Bandaga is located approximately 40 kilometers north of the capital city of Bujumbura and alongside one of the country&apos;s few paved roads.

Jan 1, 1984

By Yael Miron

Ammonium nitrate-fuel oil (AN-FO) mixtures are used as blasting agents in mining pyrite-bearing ores. The temperature of these ores can increase by the continuous, though at times slow, oxidation weathering of the pyrites. At elevated temperatures, AN-FO reacts exothermally with pyrite, and the reaction becomes self-sustained at 120° C ± 10° C. The Bureau of Mines has conducted an investigation to determine the reactivity of mixtures of AN-FO with pyrite containing ferrous sulfate. The results of tests in a heated vessel simulating a hot borehole demonstrate that small amounts of ferrous sulfate, a major product of pyrite weathering, initiate a self-sustained exothermic reaction with AN-FO at 80° C. Five pct by weight of urea was found sufficient to prevent a reaction among the three ingredients, at least within the limits of the test, which reached 180° C. Smaller amounts of urea and of potassium oxalate slowed down the reaction and delayed its onset to higher temperatures, but did not prevent it.

Jan 1, 1979