Search Documents

By Deborah A. Kramer

As part of the Nation's growing concern with the competitiveness of U.S. firms in the world economy, especially with respect to advanced materials, the Bureau of Mines assessed the actual and potential recovery and manufacturing capabilities for gallium and gallium arsenide (Gacis). GaAs has advanced from a laboratory curiosity to a material with important "high-tech applications within only the last few years, and although protected North American gallium supplies are currently considered adequate, consumption could grow to the point that this assessment would need reevaluation.

Jan 1, 1988

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the noncondensable cases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of uses produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills.

Jan 1, 1931

By Raymond F. Helinski, Linda J. McWilliams, Sean Gallagher, Thomas R. Battenhouse, August J. Kwitowski, John R. Bartels, Dean H. Ambrose

This report examines the boom arm vertical speed for roof bolting machines to study a moving boom arm appendage at different speeds during different work scenarios. The goal of this study is to determine the impact of the appendage speed on the likelihood of the operator's hand, arm, head, or leg making contact, such as touching the moving appendage. The overall research goal is to reduce workers' risks to injury from exposure to underground mining machinery. Accident investigation reports from the Mine Safety and Health Administration do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are not feasible because of safety issues. As an alternative, researchers used a unique computer simulation model that uses a virtual human, vision tracking, and generates random virtual human motions and risky work behaviors. By using specialized software to simulate the computer model, researchers accurately identified potential hazards of tasks where it is not possible to perform experiments with human subjects. Results of a frequency distribution analytic approach show that, regardless of other variables, contact incidents were always greater when the boom was moving up, always greater on the hand, and always greater or the boom arm part of the machine. The reason why the subject experiences more contacts when the boom arm is moving up rather than down is that more risky behaviors occur during drilling and bolting when the boom is ascending. Results of a cross-tabulation analytic approach show that the 25th-percentile operators experienced more contacts than other operator sizes and had most of their contacts during a boom speed of 13 in/sec. The hand-on-boom behavior during drilling and bolting tasks experienced more contacts than other work behaviors, and both tasks had most of their contacts during speed 13 in/sec. The 60-in seam experienced more contacts than other seam heights and had most of the contacts during speed 16 in/sec. For univariate logistic regression models, seam height is the most important predictor of the probability of a contact. However, a multivariate logistic regression model predicted contacts are more likely with the both-knee work posture in the 60-in seam, a 25th-percentile operator compared to a 55th-percentile operator, and speeds 16 and 22 in/sec compared to 7 in/sec. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speeds greater than13 in/sec result in a substantial increase in risk to the roof bolter operator making contact. Speeds less than or equal to 13 in/sec are associated with a more modest relative risk of making contact, which represents a decrease in potential hazard. Virtual operator's response time has little effect on the number of contacts experienced. The mining industry can use the information in this study to reduce the likelihood that roof bolter operators will experience injury due to contact with a moving roof bolting machine's boom arm.

Jan 5, 2005

By Noel N. Moebs

The Bureau of Mines conducted five reconnaissance magnetometer traverses across a small abandoned chromite mine in the State Line district of Pennsylvania and Maryland to determine the geophysical response of the area. The results indicate that more extensive geophysical surveys of the region might establish some worthwhile guidelines for chromite exploration. While chromite only rarely can be detected directly by magnetic methods, there is a possibility that geophysical signatures in the adjacent host rock could provide some guidelines for further exploration. Prior to 1875, all the chromite produced in the United States came from the State Line district, and the potential for discovering additional podiform deposits could be significant. Virtually no state-of-the-art geuphysical or geochemical studies have been conducted in this district since World War II and sizable areas remain undeveloped and suitable for exploration. While the results reported in this paper are not supported by drilling, it may encourage others to investigate the area more fully for improved methods of detecting subsurface podiform chromite deposits. New theories on the emplacement of ophiolites also could contribute to an assessment of the chromite potential of the serpentinite belt.

Jan 1, 1991

By Jon C. Volkwein

The canopy-air curtain was originally developed by the Bureau of Mines to surround the operator of a continuous mining machine with a zone of clean air. This report describes the application and testing of a canopy-air curtain on a gathering-arm loader, as well as some of the problems associated with providing a zone of clean air to a standing, semimobile operator. The area of air-curtain coverage and effects of air velocity are discussed. In its present form, the canopy-air curtain provides a 50 percent reduction in respirable dust to the operator.

Jan 1, 1981

By L. W. Higley

Procedures were developed for reclaiming high-temperature alloy scrap in the form of standard cobalt-base alloy. A cobalt-base, multicomponent, high- temperature alloy, such as S-816, can be successfully melted from scrap, and its specified chemical composition can be retained. Induction furnace melting in a controlled atmosphere was used to obtain ingots that were subsequently fabricated by impact forging to provide specimens for heat treatment and testing. Of the numerous metal elements in S-816 alloy, only small quantities of molybdenum were lost in the melting operation as finally developed. Test results indicated that the scrap material, after melting, forging, and heat treatment, was equivalent in room-temperature tensile strength, in high-temperature creep and stress-rupture properties, and in chemical composition to commercially produced S-816 alloy made from virgin material.

Jan 1, 1963

By M. J. Ackerman, C. R. Waine, W. M. Merritts, L. P. Mokwa

Tests were conducted in the Pocahontas No. 4 coalbed in southern West Virginia to determine if successful degasification techniques, developed during an earlier study in the Pittsburgh coalbed, would be effective in removing methane from those usually more gaseous coals. Specially designed long-hole drilling equipment and Bureau of Mines continuous recording devices were used to measure the quantity and methane content of the ventilating air during the investigation. Infusions were made with water at normal waterline pressures ranging from 200 to 220 psi or at pump pressures ranging from 400 to 650 psi. Results of the tests showed that methane emissions from free-flow bleeder holes were as much as 131 cfm. Infusions of some of the holes increased the methane emission from other holes and from the exposed coal surfaces near the working areas as much as 1,540 cfm. The methane content in the main return-air currents after infusion was reduced more than 86 percent of the amount recorded before tests were made.

Jan 1, 1963

By W. L. Hunter

Eleven steelmaking heats are described in this Bureau of Mines report in which acid practice was used to produce carbon steel from pre reduced iron ore pellets. Furnace slags obtained with no flux addition to the charge became quite viscous as they cooled, which precluded pressure casting from a ladle. Lime was added to the furnace charge at two levels to eight of the heats to modify slag characteristics in the furnace, and to the ladle in two heats to further modify the ladle slag cover. Selected ingots from nine heats were successfully rolled on a commercial mill to produce No. 10 reinforcing bar.

Jan 1, 1974

By J. Shawn Peterson, David S. Yantek, Adam K. Smith

Exposure to excessive noise over time can cause permanent hearing loss. Workers in the mining industry are frequently exposed to A-weighted sound levels in excess of 90 dB. The A-weighted sound level at the roof bolter operator’s location can exceed 100 dB while drilling. The National Institute for Occupational Safety and Health (NIOSH) measured the sound pressure at the roof bolter operator’s position and utilized a phased array of microphones with beamforming software to identify noise sources on a roof bolting machine while drilling. The test data indicates the sound level at the operator’s position is dominated by the 2000 Hz through 5000 Hz one-third­octave-band sound levels. The beamforming results indicate that the drilling noise is primarily from two areas: the portion of the drill steel just below the rock and the drill steel-chuck interface. This paper will discuss the methods used to identify the primary noise sources.

[ ]

Jan 1, 2012

By D. R. Douslin

This report describes an inclined-piston pressure gage that operates from a zero-pressure datum level. The gage is adaptable to accurate vapor-pressure measurements in the low and intermediate pressure range, 0.01 to 40 mm (mercury). Residual friction in the oil-lubricated piston-cylinder combination is eliminated by a unique oscillatory method that is free of end thrust on the piston and allows the full sensitivity of the gage to be realized. The axial component of the weight-to-area ratio of the piston is determined by measuring the angle of inclination with a goniometer that can be read to 1 sec. Accuracy of the gage proper is estimated to range from 0.001 to 0.012 mm from lower to upper pressure limits. Its highest practical sensitivity is about 0.0005 mm. As a test, the vapor pressures of ice and water were measured in the range -30° to +20° C.

Jan 1, 1963

By August J. Kwitowski

This Bureau of Mines report describes how the reinforcement mechanisms of untensioned, full-column resin bolts were determined during one underground study. Both axial and transverse shear loadings were identified for two instrumented resin bolts that replaced standard resin bolts in an opera-ting room-and-pillar mining section. The strain responses of resin bolt steel cores to local axial and transverse shear loadings are described. This information was obtained from laboratory testing of resin bolts installations; it was also used to analyze the data from the underground test.

Jan 1, 1980

By E. D. Gardner

This paper is one of a series on milling methods being published by the United States Bureau of Mines. Atlanta is in Elmore County, Idaho, about 80 miles from the railroad at Mountain Home, Idaho. The concentrator is at an elevation of, 6,000 feet and located in a timbered, well-watered region of relatively heavy snowfall. The snow, however, does not seriously affect local operations. The track road to Mountain Home, which passes over a mountain range, is closed each winter from about November 1 to June 15. During this period concentrates are stored and bullion is shipped by airplane. Power is generated by a Diesel engine and by an auxiliary hydroelectric plant. Gold is the principal metal produced; the or also contains an able quantity of silver.

Jan 1, 1935

By Robert F. Holub

The Bureau of Mines has evaluated four working-level radiation-measurement methods and optimized them from the inherent and statistical error standpoint. Optimization with respect to various sampling and measurement times yielded no marked improvement over the existing methods. However, when appropriate approximations are made and evaluated, these two-measurement methods can be reduced to simple formulas, eliminating a need to use nomograms. These modified methods also have improved inherent error characteristics. A new method--a combination of two existing methods--with improved inherent and statistical errors has been suggested. All the pertinent equations are given, together with the computer program, so that any two-measurement method can be readily evaluated.

Jan 1, 1980

By Edward L. McHugh, Jami M. Girard

While less than 1% of reported accidents are associated with slope stability problems, slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technologies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyper spectral imager were conducted to assess its value for improving geologic maps of potentially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized monitoring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.

By d&apos, Kathleen J. Amico

THIS SUMMARY is shown in volumes I and III of this series on mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and exported from the United States. For further details on production, see the several commodity and area chapters. A summary table comparing world and U.S. mineral production also is included. [ ]

Jan 1, 1960

By Donald M. Hausen

Diamond-bit performance and cost data accumulated by the Bureau of Mines in core-drilling schists reveal significant trends of economic interest. Low-quality, small-size drill bort were the most economical. The percentage of core recovery, type and size of bit, and bit matrix are also correlated with bit performance and costs. Detailed analyses of the factors affecting diamond-bit performances and costs are assessed in the tables, graphs, and discussion.

Jan 1, 1956

By W. Wallace, T. Ong, M. Gautam, M. Keane, S. Xing, J. Harrison

"Diesel exhaust soots were assayed in the Ames Salmonella typhimurium histidine reversion assay system using TA 98, the soots being applied as the following preparations: dispersion in dipaimitoyl glycerophosphoryl choline (DPL), dispersion in dipalmitoyl phosphatidylethanolamine (DPP!), and dispersion in dipalmitoyl phosphatidic acid (DPPA) in physiological saline, and in physiological saline without added surfactant. The extracts of soots by dichloromethane / dimethylsulfoxide (DCM/BHSO) were also assayed. Studies were performed both with and without :IQ microsomal activation of the soot preparations. The DPP! and DPPA surfactants were chosen as phospholiridz with two palmitic acid moieties esterified to a glycerol as is the case with DPL, but with hydrophilic groups having different electrophilic characters. The soots, without S9 activation, showed mutegenic activity when extracted in the conventional procedure with DCM/DMSO. The mutagenic activity of soots dispersed in DPL was quantitatively comparable to, and in some cases greater than, the activity expressed by an equal mass of soot extracted by DCM/DMSO. Soots in other surfactantpreparations, DPP! and DPPA, also expressed positive mutagenic activity. Praincubation with S9 microsomal enzyme fraction reduced the activity of solvent extracted soots, and greatly diminished the activity of DPL dispersed soots. Initial sister chromatid exchange (SCE) assays using the Chinese hamster V79 cell line indicated DPL dispersed soot also can cause SCR in mammalian cells. Results thus far suggest that surfactant suspended or ""solubilized"" respirable soot particles could provide a mechanism for transport and expression of mutagens in the lung."

Jan 1, 1989

By Kelly C. Strebig

Laboratory tests were conducted by the Bureau of Mines to determine the effect of depth of cut and bit type on respirable coal dust generation. Apparatuses were constructed to contain the coal samples, measure the linear cutting forces, and analyze the dust generated. Single-bit tests were conducted in Illinois No. 5 and Pittsburgh seam coals with five bit types at four depths of cut. The results showed that bit type did not significantly influence dust production. On the other hand, deep-cutting bits were more efficient and generated substantially less respirable dust per pound of coal broke than shallow-cutting bits.

Jan 1, 1975

By Richard J. Mainiero, Marcia L. Harris

The New York State Department of Transportation recently commenced highway widening and drainage improvement projects in Clarence and Amherst, NY. Drainage improvements including the installation of storm sewer lines required excavation to a depth of 2.5 m (8.2 ft). In September 2002, NYSDOT stopped further blasting when 800 ppm CO was detected in the basement of a house near the blasting site. At the insistence of NYSDOT, the general contractor developed a new blast plan with the assistance of an environmental consultant. The plan provided for the installation of multi-gas monitors in buildings of special concern and/or with basements and residential type CO monitors in all other buildings within 100m (330 ft) of the blast. The multi-gas monitors would be remotely monitored. The plan provided action levels which would ensure public safety. The blast design was also modified to allow for better venting of CO. Blasts were limited to 20 ft lengths. The overburden was to be removed from the rock and blasting mats put in place to prevent flyrock. Approximately twenty feet of trench adjacent to the blast was left open to allow ground movement and gas release. The use of CO monitors was effective to alert occupants of a building to the presence of CO. The most effective appeared to be the residential type CO alarms with digital readouts. They were simple and easy to use and allowed the public to participate in the process. False alarms were repeatedly received with the more sophisticated instrumentation. Residential type CO monitors are preferable to warn people near blast sites. More sophisticated instrumentation should be avoided unless personnel are experienced in its use. A general overview of the blasting and monitoring is presented and discussed. The use and effectiveness of residential type CO monitors and multi-gas monitors are discussed.