Search Documents

1. Alford, N.G. quantity, of timber used in soft-coal mines and how much will be needed for the future. Gives a table of estimated increase in mine timber consumption in the future. A.I.M.E. Separate. 1336-C 1924. 2 Clark, B.M. The forest and the mine. Rept. Conference of Wood-Using Industries, Harrisburg, Pennsylvania. Apr. 13-14, 1921, pp. 58-62. Describes experience of a Pennsylvania mining company in depletion of timber supply and conservation methods adopted.

Jan 1, 1925

By Daryl E. Radcliffe

Ninety-seven roof bolts were instrumented with strain gages and resin-grouted in three areas of the Bear coal mine, Somerset, Colo., by the Bureau of Mines. Measurements taken with these instruments indicate roof support is achieved through a combination of point suspension and resistance to vertical and horizontal stresses caused by localized shearing in the roof. The localized shearing results in bending of the bolts, yielding due to high vertical stresses, and the transfer of high loads to the bolt head or plate.

Jan 1, 1980

By Everett A. Sondreal

Material and energy balances for stockpiled lignite were calculated by computer simulation techniques to determine the occurrence of spontaneous heating. Data on properties of lignite which affect spontaneous heating were required. In some cases, best values from reported data were utilized; in other cases, new data were developed. These include specific studies on the rate and conditions that influence oxidation, heat of oxidation, heat of wetting, specific heat, thermal conductivity, and permeability of stockpiles to air. These data are presented and discussed in detail for possible application to other studies. Results of computer simulations confirm past field experience on the storage of lignite containing as-mined moisture, and predict a greater risk of heat occurrence in stockpiles of dried lignite where experience is lacking. Successful storage was predicted for dried lignite of 20 pct moisture content, if it were cooled after drying and compacted to an interparticle void fraction of 9 pct (bulk density of 67 lb/cu ft) compared to 10 pet void fraction (72 lb/cu ft) for as-mined lignite.

Jan 1, 1974

By George J. Conroy

This Bureau of Mines publication describes several fault locators and methods, including time domain reflectometers, a frequency domain reflectometer, tone generators, an infrared method, the Murray loop method, and high-voltage "click" methods. The Bureau of Mines has been conducting research into these methods for several years, to improve mine safety and facilitate production through rapid, safe location of trailing-cable faults. The problems encountered in practical applications are discussed, and schematic diagrams of several instruments fabricated by the Bureau are presented. Since no present single method of locating trailing-cable faults is universally applicable, a kit composed of several of the more promising fault locators is advisable.

Jan 1, 1978

By C. J. Thompson

In the course of the work currently conducted by the Bureau of Mines in cooperation with the American Petroleum Institute Research Project 48 on identifying sulfur compounds in petroleum, a micromethod was developed (12)5 for catalytically removing the sulfur atom from sulfur compounds. The product is the residual portion of the molecule; the structure otherwise was unaltered except for hydrogenation of any unsaturated bonds that were present in the original compound. Positive identification of sulfur compounds isolated from crude oils is a difficult problem. Direct comparison of properties of the unknown with those of reference compounds is often impossible because of the limited number of reference sulfur compounds available. However, a relatively large number of pure hydrocarbons is available, and the conversion of the sulfur compound to a hydrocarbon enhances the possibility of identification. The technique also can be used to prepare microquantities of scarce hydrocarbons by hydrogenating compounds that are readily available.

Jan 1, 1962

By F. W. Richard

This paper describing the mining practices at the Ground Hog Unit of the Asarco Mining Co., a subsidiary of the American Smelting and Refining Co., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts of the United Stated. The Ground Hog mine is at Vanadium in the Central mining district, Grant County, N. Mex., about 1.0 miles east of Silver City and 2 ½ miles southwest of Santa Rita. A branch line of the Atchison, Topeka & Santa Fe Railway connects Vanadium with Deming, about 45 miles southeast.

Jan 1, 1930

By Phyllip Worley, Frank E. Chase, Christopher Mark

The Harris No. 1 Mine, located in Boone County, WV, has been longwalling the Eagle Coalbed for over 30 years. Harris has experienced numerous interactions associated with the extensive room-and-pillar and longwall mining operations which have been conducted in the overlying No. 2 Gas Coalbed. The problems have included roof falls, excessive rib sloughage, and gateroad and bleeder entry closure. A detailed evaluation of the multiple seam experiences at Harris No. 1 Mine was conducted as part of the National Institute for Occupational Safety and Health (NIOSH) nation-wide multiple seam mining case history data base. One observation from the Harris gateroad case histories was that smaller, critically loaded, upper seam pillars seemed to cause more severe ground conditions than did wider pillars. The LaModel program was used to investigate this supposition, and the results confirmed that “critical” sized pillars do transmit the highest amounts of stress to adjacent seams. In addition, the data suggest that the probability of a major multiple seam mining interaction increases when the depth of cover is 1,000 ft or greater and when the Eagle seam pillars have a Analysis of Longwall Pillar stability factor less than 1.50.

By Fred D. Wright

A drill unit designed by Bureau of Mines engineers for testing various types of rotary bits has been in use since April 1950 at the experimental oil-shale mine near Rifle, Colo. The unit has a hydraulic drill and feed system, which provides the wide range of operating conditions necessary for adequate testing of drill bits and for obtaining data needed for the design of production scale equipment. Through the use of this unit, it has been proved that rotary drilling of vertical holes for mining the benches of the oil-shale mine is much cheaper than percussion drilling, and it is believed that in the near future the rotary drilling of horizontal blast holes in the top heading of the mine will prove equally economical.

Jan 1, 1952

By Donald W. Mitchell

The fire hazard of neoprene, polyvinyl chloride, and rubber conveyor belts was studied at the Federal Bureau of Mines Experimental Coal Mine. The effects of intensity of ignition source, velocity of the ventilating air, and type of belt were investigated at three levels in small-scale gallery experiments. Studies were made in the mine on the effects on ignition and flame propagation of belt-entry dimensions, belt widths, and belt configuration. Methods for extinguishing belt fires were also investigated under simulated mining conditions, and during these trials coal dust and grease were placed on the belt. The research showed that conveyor belts will burn. Neoprene, polyvinyl chloride, and rubber belts, with and without carcass, ignited and propagated flame. The highest rate of flame propagation was obtained on rubber belt. The fire hazard increased with increase in intensity of ignition source and air velocity. Flame propagated only when air was forced through the test zone; propagation was not obtained when forced ventilation was not used, as would exist in a neutral entry in a mine. Automatic water sprays and high-expansion foam effectively arrested flame propagation; direct application of water and bicarbonate dusts was ineffective.

Jan 1, 1967

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolanic-cement concrete to develop a low-strength backfill. Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan (fly ash) and lime. Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressive-strength curves that can be used to estimate the best backfill mix for any mine.

Jan 1, 1981

By Robert J. Timko

The objective of this Bureau of Mines research work was (1) to determine how well the E. I. Du Pont de Nemours and Company P-2500 personal dust sampling pump controls the flow rate at 2 L/min and (2) to compare respirable dust mea-surements made using the P-2500 with those made using a nonpulsating sampling flow system, both using the Dorr-Oliver 10-mm nylon cyclone dust size classifier. The calibrator and the operation manual for the P-2500, supplied by the manufacturer, were also evaluated. Flow tests consisted of long-term (6-to 8-hour) flow stability tests at various backpressures, a low-flow indicator examination, flow controller response time tests and pulsation tests. Dust tests were performed using coal, silica, and Arizona road dust. No tests were performed to examine effects of temperature, barometric pressure, vibration, or mechanical shock. These pumps performed well within manufacturer specifications in all tests.

Jan 1, 1982

By John Millhiser, Stephen J. Kravits

The U.S. Bureau of Mines preproduction Wireless Survey System (WSS) and its performance during an in-mine test are discussed in this report. The WSS was developed to reduce downhole surveying time in order to increase the efficiency of drilling long horizontal methane drainage boreholes in coal. Borehole survey data are electromagnetically transmitted from the WSS7s downhole guidance probe, via the drill rod, to the uph'ole subsystem in less than 1 min per survey transmission, regardless of borehole depth. The WSS7s in-mine test consisted of providing borehole survey data during the directional drilling of a 2,538-ft horizontal methane drainage borehole in the Pittsburgh Coalbed. By considering available drilling time, which does not include hydraulic drill downtime and the time spent traveling portal to portal, 24 shifts were needed to complete the borehole. Of the available drilling time during the tcst, 50 pct of the time was spent drilling and 50 pct surveying and maintaining the WSS to keep it operational. Previous Bureau experience indicates drilling efficiency was increased 108 pct because of the WSS, in comparison with using a commercially available wire-run directional survey instrument at 10-ft intervals.

Jan 1, 1990

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By B. E. Blair

Accelerometers of various types, velocity gages, and a displacement meter are shown to give reliable date when measuring seismic pulses generated in rock by the detonation of explosive charges. Displacement and velocity records are differentiated and shown to compare with velocity and acceleration records. Velocity and acceleration records are integrated and shown to compare with displacement and velocity records, respectively. The experimental data are shown to satisfy the scaling laws developed by dimensional analysis. Propagation laws are developed for peak amplitudes of the first pulse of displacement, velocity, and acceleration. These propagation laws are shown to be independent of the gage used to obtain the data. As a result, the usefulness of the various gage types can be extended. For example, accelerometers, because of their high frequency and amplitude limits, can be employed near the shot to measure acceleration and/or velocity (by integration), Velocity gages, because of their higher sensitivity, can be employed at relatively larger distances from the shot to measure velocity and displacement or acceleration (by integration or differentiation).

Jan 1, 1954

By Alex C. Smith

This report describes laboratory studies conducted by the Bureau of Mines to evaluate the effectiveness of 10 additives to inhibit the self-heating of coal. Aqueous additive solutions were applied to a bituminous coal with a high spontaneous combustion potential, and the minimum self-heating temperatures (SHT's) of the dried coal-additive mixtures were determined in the Bureau's adiabatic heating oven. The relative effectiveness of the additives was determined by the observed changes in the minimum SHT's of the mixtures, or by the time required for the sample temperature to reach 150" C, compared with the untreated coal and a coal-water blank. Sodium nitrate, sodium chloride, and calcium carbonate were found to be the most effective inhibitors, followed by ammonium dihydrogen phosphate, calcium chloride, ammonium chloride, sodium acetate, and potassium chloride. Two additives, sodium formate and sodium phosphate, promoted the self-heating process. Differential scanning calorimetry experiments on the coal-additive mixtures showed that reactions occurred between the coal and some of the additives, but these reactions did not influence the self-heating process.

Jan 1, 1988

This report summarizes the results of several field tests conducted by Collins for the Bureau of Mines under contract SO122076 and contract H0232056. The field projects represent a part of Collins continuing effort on a broad study of coal mine communications. These experiments analyze the propagation characteristics of radio signals in a working coal mine environment. The intent of the program is to provide basic propagation loss characteristics by which we may evaluate various approaches to an integrated mine communications system. The goal of such a system is to satisfy both operational and emergency communications needs in the mine. Field testing was conducted during the last week of November 1972, at a coal mine operated by Inland Steel Company, near Sesser, Ill, and in the Robena No. 1 Mine, Waynesburg, Pa, on 12 March 1974. The tests included uhf propagation losses and noise (200 MHz to 1 GHz) in the Sesser, I11 mine location and vlf propagation loss and noise (1 to 200 kHz) in both of the above locations. The basic experimental parameters were frequency, polarization, antenna type/orientation, and distance. The following reports treat the various aspects of the test programs in detail. Since different antenna configurations were used in the two mines, each report contains its own experimental predictions drawn from its corresponding test activities. A test equipment list and block diagrams of typical experimental setups for the tests of section 2 are contained in appendix A.

Jan 1, 1974

By G. E. McClelland

During the 1970?s, the Bureau of Mines investigated a particle agglomeration technique for improving the flow of leaching solution through heaps of clayey or crushed, low-grade gold-silver ores, wastes, and tailings. This technology has been adopted on a broad scale by the precious-metals-processing industry. This report presents information on five commercial operations that have benefited from agglomeration technology and that represent a cross section of current heap leaching practice. The technology is cost effective because of decreased leach times and improved precious metal recoveries.

Jan 1, 1983

By J. H. Heginbotham

As part of the total metallurgical system to recover metals from secondary resources, the Bureau of Mines conducted froth flotation research, using cationic reagents to recover glass from urban refuse. Batch flotation tests showed that high-quality cullet can be obtained from glass-rich aggregates derived from municipal incinerator residues and unburned refuse. This was confirmed by pilot plant operations treating 350 pounds of flotation feed per hour. Aggregates containing 85 to 90 percent glass were wet-ground to minus 20 mesh, deslimed in two stages, and fed to flotation cells. The glass was selectively floated using an amine collector, usually in an amount under 0.2 pound per ton of solids in the feed. The glass concentrates from the rougher cells were cleaned by refloating two or three times. Over 90 percent of the glass in the deslimed feed was recovered in the cleaned concentrates.

Jan 1, 1978

By E. Chin

Natural gas was the only economically significant mineral produced. A significant amount of the gas output was consumed in the production of nitrogen fertilizer and electric power. Proved reserves of natural gas were abundant and at least sufficient to supply most of the country's industrial and domestic needs for many decades to come. Other mineral production was of little importance to the Bangladesh economy, although there were prospects for developing some of the nonmetallic minerals. The flat river-delta terrain comprising nearly all of Bangladesh made the potential for discovering major, economically exploitable mineral deposits poor. The deep sediments, however, have good potential for crude oil or additional natural gas discoveries.

Jan 1, 1985

By L. C. IlsLey

Coal mining is more widely distributed throughout the United States than is generally known, as 30 States are credited with having coal mines. In 1919 twenty-three of these States each produced at least a million tons of bituminous coal, and all the States produced about 560,000,000 tons. In addition, Pennsylvania produced about 85,000,000 tons of anthracite. Twenty-eight States have regulations prepared by commissions or have enacted laws governing the operation of coal mines. Pennsyl¬vania has separate codes for the anthracite and bituminous fields. The codes may be classified as follows: Twelve distinctly coal¬mining codes; eight codes that are essentially coal mining, but also apply to other mines; five codes that are subdivided, referring partly to coal mines and partly to other mines; and four codes that are essentially metal mining, but apply in part or in whole to coal mining. The first State to have a coal-mining law was Pennsylvania, which enacted a law, for Schuylkill County only, in 1869. The first State to enact a coal-mining law governing all the coal mines in the State was Illinois in 1872, followed by Ohio in 1873. Pennsylvania in 1879 enacted a law for anthracite mines only, but did not enact similar laws for bituminous mines until 1577. At least 10 other States enacted coal-mining laws between the years 1870 and 1890. Before 1890 electricity was little used in coal-ruining operations and therefore practically no provisions governing the installation, inspection, or maintenance of electrical equipment were made in any of the laws enacted up to 1890. In the law of Colorado, approved April 8, 1885, there is a reference to the use of telephones, probably the first reference to electrical equipment of any kind in a State-mining code. Most of the mining codes have been changed from their original form by amendment or by complete revision. In some of the early changes a casual reference is made to the use of electricity or to the handling of electrical equipment. In 1911 Pennsylvania added

Jan 1, 1920