Search Documents

By Thomas J. Fisher, John J. Sammarco

This report (System Safety 2.1) is the second in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics, and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard 61508 [IEC 1998a,b,c,d,e,f,g] and other recognized standards. The scope is “surface and underground safety mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system.

Jan 4, 2001

By V. Castranova, K. VanDyke

"INTRODUCTION A soluble mediator has been described which is released from activated rabbit leukocytes and induces histamine secretion from rabbit platelets (Barbaro and Zvaifler, 1966; Siraganian and Osler, 1971). This factor has been isolated, characterized and named platelet activating factor, PAF (Bcnveniste et. al., 1972). PAF has since been chemically identified as l-0-alkyl-2-acetyl-sn-glyceryl-3-phosphocholine (Benveniste et. al., 1979; Demopoulous et. al., 1979).PAF is a lipid mediator of broad biological activity. It causes smooth muscle contraction, contraction of lung tissue and decreased FEV 1; while enhancing capillary permeability thus causing edema (Pinkard, 1983). In addition, PAF is a chemoattractant and can lead to inflammation.PAF has been reported to stimulate the release of lysosomal enzymes, leukotriene B,, and lipid metabolites from neutrophils (Smith et. al., 1983; Shaw et. al., 1981; Lin et. al., 1982; O'Flaherty et. al., 1984). The objective of the present investigation was to further characterize PAP-induced stimulation of granulocytes and to develop a bioassay, i.e. chemiluminescence, for screening PAF receptor antagonists and inhibitors of PAP-induced activation of granulocytes. The possible use of the chemiluminescence assay to monitor PAF synthesis by human granulocytes is also described.METHODSBlood was drawn from healthy volunteers into a blood storage bag containing CPD anticoagulant. Granulocytes were partially purified by dextran sedimentation and further purified by centrifugal elutriation as described previously (Jones et. al., 1980). Granulocytes obtained by this procedure were approximately 95 percent pure. The number of granulocytes in this preparation was determined using an electronic cell counter (Coulter Model Z1, Coulter Instrument Co., Hialeah, FL). Isolated granulocytes were used to monitor membrane potential, hydrogen peroxide and superoxide release, oxygen consumption, calcium uptake and, in some cases, chemiluminescence. Studies of PAF receptor antagonists were conducted using neutrophils isolated by density centrifugation. Briefly, blood was layered onto Mono-Poly-Resolving Medium (Flow Laboratories, McLean, VA) and centrifuged at 22 °C and 300 g for 30 min. Neutrophils collected from the second band of this gradient were at least 90 percent pure."

Jan 1, 1989

By Albert E. Long

By the USB of X-ray diffraction methods, scientists have learned how the atoms in a diamond crystal are arranged and how the atoms are tied together by chemical bonds. They have found that, even though the bonds between all atoms of the diamond have equal strength, they are so distributed that there are more bonds in certain layers or directions through the crystals than in others. The unequal distribution of the bonds in certain directions creates planes, within the diamond, of unequal strength and resistance to abrasion. The location and disposition of the directions that are relatively harder than the others were determined by Slawson and Kohn 3/ in 1950. By plotting these directions on stereographic projections they delineated the hard regions on the surface of the diamond, but only those trained in the methods of crystallography can readily interpret their diagrams. The principal purpose of this report is to present information that will help individuals without previous training in crystallography to learn to recognize the special features of the surfaces of diamond crystals that are definite guides to the location of the various hard directions of the stones. A crystallographer trained in using various precise laboratory instruments might consider such rudimentary criteria as rather unscientific, but these simple characteristics of diamond crystals are practical clues which anyone equipped with a magnifying lens can find and recognize. The use of the special faces, points, edges, and growth lines as a gui.de in orienting a diamond will allow it to be placed in a position reasonably close to the optimum. Preliminary results of experimental work conducted by the Bureau of Mines indicate that this is all that is necessary in setting diamond-bit crowns. This experimental work demonstrated that setting bits with the hard vectors of the diamond as cutting points greatly reduces the diamond loss and increases the efficiency of the bit.

Jan 1, 1952

By Donald P. Tuchman, Robert P. Vinson, Steven J. Page, Linda J. McWilliams, Gerald J. Joy, Steven E. Mischler, Jon C. Volkwein

The United States National Institute for Occupational Safety and Health, through an informal partnership with industry, labor, and the United States Mine Safety and Health Administration, has developed and tested a new instrument known as the Personal Dust Monitor (PDM). The new dust monitor is an integral part of the cap lamp that coal miners normally carry to work and provides continuous information about the concentration of respirable coal mine dust within the breathing zone of that individual. Previous laboratory testing demonstrated that there is a 95% con?dence that greater than 95% of individual PDM measurements fall within ±25% of reference measurements. The work presented in this paper focuses on the relationship between the PDM and respirable dust concentrations currently measured by a coal mine dust personal sampler unit utilizing a 10 mm Dorr Oliver nylon cyclone. The United Kingdom Mining Research Establishment instrument, used as the basis for coal mine respirable dust standards, had been designed speci?cally to match the United Kingdom British Medical Research Council (BMRC) criterion. The personal sampler is used with a 1.38 multiplier to convert readings to the BMRC criterion. A strati?ed random sampling design incorporating a proportionate allocation strategy was used to select a sample of mechanized mining units representative of all US underground coal mines. A sample of 180 mechanized mining units was chosen, representing approximately 20% of the mechanized mining units in production at the time the sample was selected. A total of 129 valid PDM/personal sampler dust sample sets were obtained. A weighted linear regression analysis of this data base shows that, in comparison with the personal sampler, the PDM requires a mass equivalency conversion multiplier of 1.05 [95% C.I. (1.03, 1.08)] when the small intercept term is removed from the analysis. Removal of the intercept term results in a personal sampler equivalent concentration increase of 2.9% at a PDM measurement of 2.0 mg m-3.

By John Owens, Marc Endicott, Hamid Maleki

This study presents a historic overview of the role of mobile roof support (MRS) technologies in improving stability and worker safety and presents the results of recent field evaluations of the MRS load rate monitoring device and other remote deformation-monitoring techniques. Field studies were implemented at two sites in cooperation among researchers from the National Institute for Occupational Safety and Health (NIOSH), Maleki Technologies, Inc., and J. H. Fletcher & Co. The objective of the field programs were to (1) study the interaction between MRS’s and coal mine strata and (2) develop and test suitable monitoring systems for assessing roof and pillar stability. An MRS consists of a roof canopy, four hydraulic cylinders, a caving shield canopy, and associated electromechanical systems mounted on crawler tracks. The machines are controlled by radio from a remote location and operate on self-contained power units. Typically, MRS’s have capacities of 5,340 and 7,120 kN (600 and800 tons). In comparison to posts, an MRS is capable of maintaining the yield load after significant amounts of roof-floor deformation. Because the mining cycle is accelerated, MRS’s help reduce the potential for time-dependent roof falls. MRS performance has been monitored in the laboratory under controlled static loading conditions and in the field under deep, two-seam mining conditions. Laboratory studies have quantified support capacity and system stiffness as a function of machine height. Field investigations have focused on determination of optimum operating conditions and development of warning systems that indicate excessive load on the machine and/or impending roof-pillar stability problems. Analyses of field data show that roof instabilities are influenced by (1) pillar failure, (2) pillar yielding, (3) mine seismicity, (4)geologic structures, and (5) panel layout designs and mining practice.Pillar yielding and failure (unloading) and seismicity can be conveniently monitored by the load rate monitoring device, but for consistent detection of roof falls, additional deformation measurements directly within the cuts are needed.

By Fred N. Kissell, Jon C. Volkwein

In This Chapter [How inert gas works to prevent methane explosions How inert gas is generated and delivered at highwall mines Volume and quality requirements for inert gas at highwall mines How an inert gas system is operated and Precautions to take during mining to prevent methane explosions] This chapter discusses a method, originally developed by Volkwein and Ulery [1993], to prevent methane explosions during highwall mining. In highwall mining, a horizontal auger or a mining machine enters the coal seam from a surface mine pit at the bottom of a highwall, and the coal is mined out from a series of parallel holes. Explosions can be prevented by injecting inert gas into each hole as it is mined. Coal near the surface has lost most of its methane gas over time. However, in recent years, surface mining has been used for deeper reserves of coal. This trend toward mining deeper reserves has increased the chance of encountering methane, and methane explosions at highwall mining operations have resulted in injuries. HOW INERT GAS WORKS TO PREVENT METHANE EXPLOSIONS A methane explosion requires the presence of sufficient amounts of both methane and oxygen, as well as an ignition source. If the methane cannot be reduced and the ignition source cannot be eliminated, then explosions may be prevented by adding an inert gas, which contains little to no oxygen, to the mixture [FWQA 1970]. Just how much inert gas must be added depends on the mining rate, as well as the composition of the inert gas. An explosibility diagram can be used to show whether a methane mixture is explosive after inert gas is added [Zabetakis et al. 1959] (Figure 10–1). This diagram indicates that gas mixtures fall into one of three range categories—explosive, explosive when mixed with air, and nonexplosive—depending on the percentage of methane and percentage of “effective inert.” Effective inert is calculated from the percentage of “excess nitrogen”3 and percentage of carbon dioxide in the mixture.

Jan 6, 2006

By Clyde E. Williams

The Northwest experiment station of the Federal Bureau of Mines , at Seattle , Wash . , was established in December , 1916 , and is one of 13 mining experiment stations maintained by Act of Congress , under the direction of the bureau , in the various sections of the country . Under the terms of the organic Act (March 3 , 1915 ) , the province and duty of these experiment stations is to cake investigations and disseminate information with a view to decreasing waste and improving the efficiency in the production , treatment , and utilization of mineral substances . The investigations carried on at the Northwest experiment station attempt to cover the needs of the mineral industry of the States of the Pacific Northwest and of the coastal regions of Alaska . The most in ortant needs of this district are for work on coal washing , electrometallurgy , and ceramics . The electrometallurgical investigations are not necessarily limited to the Problems of the Northwest , but may be of general application . Problems other than those specified above are referred to other stations of the Bureau that specialize on the particular type of investigation required . The Northwest station closely cooperates with the State of Washington through the University of Washington and with the State of Oregon through the Oregon Bureau of Mines and Geology . The University of Washington at Seattle has donated the use of an entire building , which houses the station's administrative offices and chemical laboratory , and parts of two other buildings which are usea in conducting the experimental avestigations . Twenty-five thousand dollars is expended annually by the Federal Government , while the State of Washington each biennium appropriates $ 20,000 , and the State of Oregon from time to time appropriates various amounts for the conduct of work along cooperative lines . Also , the station cooperates with private organizations tht have problems similar to those in which the station is interested . For example , the Washington Electrochemical Co. is cooperating in the electrometallurgical research, and furnishes part of the supplies and technical assistance required .

Mar 1, 1922

By Ronald D. Hill, Elmore C. Grim

1. Potential groundwater pollution resulting from large-scale surface mining in western states should be evaluated. 2. Criteria should be developed for the design, construction, operation, and abandonment of sediment ponds for maximum removal of suspended solids. 3. Methods should be developed for reducing suspended solids discharges from surface mines to less than 30 milligrams per liter. 4. A manual should be developed in the form of guidelines for sediment and erosion control planning and implementation. These guidelines must be designed to cover all phases of the coal surface mining operation (i.e., before, during and after mining). 5. A mine road manual should be developed for use by surface mine operators and State and Federal Agencies. Erosion, water control, and dust control should be covered in detail. 6. The block-cut, head-of-hollow fill, and mountain-top removal methods and techniques of contour mining should be evaluated, designed, and ultimately demonstrated in steep, mountainous terrain. Designs should be prepared for single and multiple seam applications. The demonstrations must show that these mining systems will secure rapid achievement of reclamation require¬ments and provide maximum, safe, economic coal recovery in an environmentally safe manner. 7. A Blasting Manual should be developed for use by industry and enforcement agencies. Stress should be placed on how to keep vibration levels and air blast pressures well below accepted safe criteria. Also, methods that can be used to control noise should be listed. 8. Investigations should be conducted on the effect of continued vibrations from blasting on structures that are near quarries. 9. Additional guidelines need to be developed for sampling and analysis of overburden material and associated coals for trace elements and noxious strata. Samples are extremely sensitive, and the source and manner of their collection, handling, storage, and treatment, as well as the techniques of analysis, need to be developed and described. This information can be used to predict possible future problems.

Jan 1, 1974

By Richard Mainiero, James H. Rowland

For many years there have been small scale tests available for evaluating the toxic fumes production by cap-sensitive explosives (DOT Class 1.1), but these could not be used with blasting agents due to the large charge sizes and heavy confinement required for proper detonation. Considering the extensive use of blasting agent in construction and mining, there is a need to determine the quantities of toxic fumes generated by blasting agents. At the International Society of Explosive Engineers Twenty Third Annual Conference on Explosives and Blasting Technique in 1997, the authors reported on a facility for detonating large (4.54 kg), confined blasting agent charges in a controlled volume that had been constructed at the National Institute for Occupational Safety and Health’s Pittsburgh Research Lab’s Experimental Mine. Since 1997, this facility has been used to collect data on toxic fumes produced by the detonation of various ammonium nitrate/fuel oil (ANFO) mixtures and several cap-sensitive explosives. ANFO composition ranging from 1 to 10 percent (pct) fuel oil have been studied. As expected from previous studies, with an increase in fuel oil content the carbon monoxide production increases, while nitric oxide and nitrogen dioxide production decrease. The detonation velocity varies from 3,000 to 4,000 m/sec for the 1to 10 pct range of fuel oil content, suggesting that ANFO mixes with improper fuel oil content may appear to detonate properly, while their fume production differs significantly from optimum. The study also considers such factors as degree of confinement, water contamination, and aluminum content on blasting agent fume production. Results indicate that water contamination of the ANFO has little effect on carbon monoxide production, but causes significant increase in nitric oxide and nitrogen dioxide production. Decreasing confinement from Schedule 80 steel pipe to 0.4-mm thick sheet metal also has little effect on carbon monoxide production, but significantly increases nitric oxide and nitrogen dioxide production. Adding5 and 10 pct aluminum to the ANFO had no clear effect on carbon monoxide, nitric oxide, or nitrogen dioxide production.

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40° F (-40°C) with 75% No. 1125% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34" C) with 75% No. 2/25% RO, and at 0° F(-18° C)with 50/50. Reference detonation velocity tests were conducted in 1.4" (3.6 cm) diameter steel pipe at 70°F (21°C) on No. 1 diesel ANFO (94-6), giving an average value of 9722 ft/s (2964 m/s). Comparison tests showed good ANFO performance at low temperatures. Blended fuel ANFO (75% No. 1/25% RO) mixed, loaded, and tested at -40°F (-40°C), produced an average velocity of 9247 Ws (281 8 m/s). A 50/50 blend gave a velocity of 8083 Ws (2464 ds) at -20°F (-29°C). Based on these results, a practical field method has been developed to help evaluate whether a specific oil blend will mix properly with AN at a low ambient temperature. This method will help to promote the safe and reliable use of RO ANFO at low temperatures, with adequate performance.

Jan 1, 2008

By George D. Dub, FREDERICK G. MOSES

The Bureau of Mines, in connection with the investigations of war minerals it conducted, examined the graphite deposits of this country, studied the methods of mining and preparation used, and sought to devise more efficient methods for the preparation of do- mestic graphite, and to standardize the quality of the product. The graphite investigations covered three general phases, as follows: 1. An examination of the deposits in Alabama and other States, and a survey of the methods of mining and preparation used. In this connection methods of sampling and analysis were noted and ex- periments made to determine a standard method of sampling and a rapid but accurate method of analysis. 2. Experimental work on the concentration and refining of domes- tic crucible graphite to improve the quality of the product and to lessen waste. 3. Experimental work in crucible manufacture to determine the properties of domestic flake and the maximum proportions that might be used without impairing the quality of the crucibles. This work was accompanied by photomicrographic study of crucible structure. In this bulletin are presented the results obtained in the first two phases of the work outlined above. The bulletin is in two parts. The first part describes the methods of mining and milling used, suggests a standard method of sampling finished graphite, and de- scribes a rapid and convenient method of analysis developed at the Pittsburgh station of the Bureau of Mines, to which had been as- signed the analytical and microscopic work. The second part describes experiments on the concentration and milling of graphite, which were made at the Salt Lake City, Utah, station. As soon as the reports incorporated in this bulletin were ready, mimeograph copies were distributed to those persons most interested in order to make the results immediately available. The experimental work on crucible manufacture, assigned to the Columbus, Ohio, station, yielded results which were made known to the industry. Á report on this work will be published later as a separate bulletin.

Jan 1, 1920

By M. C. Simmons, Boyd Gutorie

Desulfurization experiments at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville on virgin light distillates obtained from some ‘high-sulfur’ crude oils have shown that the octane numbers of the original distillates are increased on the average about one unit, that the octane numbers of distillates with 4 ml. tetraethyl lead are increased 2 to 3 units, and that the The Petroleum Experiment Station, at the request of the Petroleum Administration for War, instigated and has in progress an investigation of crude oils of the United States to determine their possibilities for yielding straight-run distillates suitable for use as base or blending stocks to produce high octane aviation gasoline. One phase of this investigation deals primarily with so-called ‘high-sulfur’ or ‘sour’ crude oils by seeking to determine the effects of sulfur removal upon the virgin distillates prepared from these crude oils. To date, virgin distillates from several ‘high-sulfur’ crude oils from Texas, New Mexico, and Oklahoma have been prepared and desulfurized in pilot-plant distillation and desulfurization units at the Petroleum Experiment Station. The properties of the undesulfurized and desulfurized distillates were determined and compared to show the effect of sulfur removal. Results of these investigations showing the suitability of these crude oils as sources of virgin naphtha aviation base stocks have been prepared and forwarded to the Petroleum Administration for War and other approved persons. The following preliminary summary is presented to acquaint those interested not only with the present results of the investigation of several ‘high-sulfur’ Texas, New Mexico, and Oklahoma crude oils, but also to give some basic information as to certain sulfur compounds, especially their identification in straight-run distillates, their depressing effects upon the octane numbers of leaded fuels, the benefits obtained by their partial and complete removal, and some of the processes being used to effect their removal.

Nov 1, 1943

By Joseph T. Singewald

The term "titaniferous magnetite" is used to designate those mag- netic ores of iron that carry more than 2 or 3 per cent of titanium. Large and easily workable deposits of these ores occur in different parts of the world, and have attracted attention for many years. Under present furnace practice, however, the smelting of these ores is both difficult and expensive, and for that reason they are not accepted by furnaces, so that the deposits are practically worthless. The problem of finding a feasible method of utilizing these ores has naturally been attractive, and numerous attempts have been made to solve it. Experiments to that end embrace two lines of investigation. The one that has been the more frequently tried is the elimination of the titanium from the ores, so as to make possible their smelting in the usual way. The other is the devising of a method of smelting by which titaniferous ores may be reduced as economically as are non- titaniferous ores. The former method involves a physical process, the latter a chemical process. The measure of success attainable by the first method depends entirely on the relations between the iron and the titanium in the ore. Views in regard to these relations have been divergent. Some investi- gators have believed the titanium to occur as a part of the magnetite molecule, in which case, of course, any process of mechanical separa- tion would be impossible. Others have believed that the titanium occurs as the mineral ilmenite, and that the ores are aggregates of magnetite and ilmenite. In this case a separation of the two minerals is theoretically possible. Magnetite is highly magnetic; ilmenite is nonmagnetic or only feebly magnetic. Crushing and magnetic con- centration should separate them. Numerous experiments in mag- netic separation have been made with various degrees of success, but rarely has more than a very imperfect separation been obtainable. In other words, some of the titanium exists in a separable form and some in an inseparable form, and the ratio between the two forms is

Jan 1, 1913

By S. J. Page, J. A. Organiscak

Airborne respirable dust surveys were conducted at six surface coal mines to investigate the effectiveness of dust control methods used on rotary rock drills and bulldozers. Dust controls commonly used on drills include a dry dust collection system, exhausting from a shrouded area around the collared hole, and an enclosed drill operator cab, filtering airborne dust from the cab. Bulldozers are also typically equipped with an enclosed operator cab as a dust control measure. Airborne respirable dust sampling was conducted near each equipment's source of generation and inside its enclosed cab. Silica analysis was performed on the dust samples to determine the percent silica content in the dust generated at the six mining operations. An additional eight- month follow-up of dust sampling was also conducted in the enclosed operator cabs of several rock drills and bulldozers. Data were analyzed for long-term variability of accepted control methods to abate dust and silica levels. The highwall rock drill was the major and most variable dust source as compared to the bulldozer, generating dust levels, on average, one order of magnitude higher than dust levels of the bulldozer. Four of the six drills surveyed had dust containment and capture problems at the shrouded drill table above the lple. Repairs or modifications to three of the drill dust collection systems were shown to reduce dust levels by more that 50% next to the shrouded drill table. The enclosed operator cabs provided more than 90% and more than 40% lower dust levels than at the dust source for the drill and bulldozer, respectively. Long-term sampling of several of these highwall drills and bulldozers showed that the dust levels in the drill cabs were frequently higher than 0.2 mg/m3 and more variable than in the bulldozers. The bulldozer dust levels were frequently below 0.2 mg/m). Future research should focus on improving some of the deficiencies present in the drill's primary dust collection system, and developing quality control methods to ensure the integrity of enclosed cab protection for equipment operators.

By G. R. Hopkins

"Summary An apparent decline in fuel efficiency at refineries, which first became came evident in 1930 and continued through 1933, was checked in 1933 when the average amount of heat needed to refine a barrel of crude oil amounted to 660,000 B.t.u. This compares with an average requirement of 692,000 B.t.u. In 1932 and with a low of 639,000 B.t.u. in 1929. (See fig. 1.) The improvement in fuel economy in 1933 probably was closely related to the increase of 5 per cent in crude runs to stills. As much of the fuel burned at refineries is utilized for purposes other than under crude-oil stills and in relatively stable amounts, it is evident that a material increase in crude runs will usually reflected in a decrease in average fuel requirements. Another factor which has influences fuel economy at refineries in the past is the trend in cracking, a refining process requiring more than the average expenditure of heat. In 1933 production of gasoline by cracking increased slightly, but no appreciable rise in heat requirements resulted as an equivalent amount of fuel was saved in improved technique, particularly in the field of heat exchange.Since the beginning of the refining industry, the transition in fuels has been from solid to liquid to gaseous; in other words, the leadership was first held by coal, then passed to oil, and is now held by gas. In 1933, 54.7 percent of the total heat units generated came from gas, 39.0 percent from oil (including acid sludge), and 6.3 percent from coal and coke. The principal change in the relative importance of the various refinery fuels in recent years has been the rapid growth in consumption of refinery or still gas at the expense of all the other common fuels. Still gas owes its ascendency to its cheapness and availability, and probably it would have become the primary refinery fuel years ago if recovery methods had been perfected. The relative importance of coal showed a small increase in 1933, the first gain recorded since these surveys were inaugurated in 1925. The increase in use of coal was undoubtedly due to increased operations at plants using it,"

Feb 1, 1935

By Jeffery M. Listak, Ernest A. Curth

"It took only 9 years from the first appearance of roof shields on the U.S. longwall mining scene to the present predominance of shield faces. An apparent consequence is the welcome downward trend in accidents related to failures in longwall ground control. The report addresses load prediction, the effects of shield geometry on support loads, factors contributing to ground control, and related techniques. The Bureau of Mines took an active part in the evolution of longwall mining, including developing one of the first shield faces in 1975, the first lemniscatetype shields in 1976, the Mine Roof Simulator completed in 1980, the first shields in steeply pitching coalbeds in 1981, and the first multilift working of a thick coalbed in 1982. The information offered in this state-of-the-art report will assist in establishing criteria for roof support selection. INTRODUCTIONIn terms of roof support technology, the introduction of shields in the seventies and eighties was a major step forward. Table 1 indicates the predominance of shield faces on the U.S. longwall mining scene and its apparent consequence, a welcome downward trend of ground-control related accidents.The rapid progress of longwall technology began in 1975 and is highlighted by a development leading from the caliper shield to the modern lemniscate type. Shields have been gaining preference over chocks since their advent to longwall mining in 1975. Safety and productivity factors favoring shields over chocks are--1. A sheltered working space requiring minimum cleanup work.2. Structural stability that allows advancing without delay even with brushing roof contact and, by controlling all lateral loads, removing the requirement for cumbersome leg restraint and restoration devices.3. Wide hydraulic range of mining height.The development of roof shields in the Federal Republic of Germany preceded and paralleled their rapid adoption by U.S. miners. In 1983, 87 pct of the total production in Germany came from shield faces (1).2 In Great Britain, the National Coal Board introduced the first shield support system in 1977 to initiate Advanced Mining Technology (ATM) and Heavy Duty Mechanization (HDM) programs; as of mid-1982, 44 shield faces were operating, or 7.5 pct of a total of 581 faces CJ_)."

Jan 1, 1985

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals. Also, miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupational Research Agenda, problems created by occupational hearing loss include (1) the reduced quality of life due to social isolation and unrelenting tinnitus, (2) impaired communication with family members, the public, and coworkers,(3) a diminished ability to monitor the work environment (e.g., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although the elimination of hazardous noise is the ideal long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use in the workplace is usually worse than when tested under laboratory conditions. Additionally, workers may refuse to wear their hearing protection for any number of reasons. Therefore, this project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis toward optimizing the balance between effectiveness, comfort, overprotection, and communication ability. Currently, the necessary in-house laboratory facilities and research techniques are being finalized. Individual experiments are planned that involve analysis of new hearing protector technology under both laboratory and field conditions. The laboratory components are to consist of con-trolled studies using human subjects and/or an anthropometrically correct artificial test fixture to evaluate the adequacy/effectiveness of various hearing protective devices. Field studies are planned to determine the actual usefulness and practicality of the hearing protectors as used in diferent mining environments. Recommendations can then be offered to the mining community regarding correct earplug/earmuff usage that maximizes recognition of hazard/warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2000

By John J. Sammarco

Computer-related accidents have caused injuries and fatalities in numerous applications. Normal Accident Theory (NAT) explains that these accidents are inevitable because of system complexity. Complex systems, such as computer-based systems, are highly interconnected, highly interactive, and tightly coupled. We do not have a scientific methodology to identify and quantify these complexities; specifically, NAT has not been operationalized for computer-based systems. Our research addressed this by operationalizing NAT for the system requirements of safety-related computer systems. It was theorized that there are two types of system complexity: external and internal. External complexity was characterized by three variables: system predictability, observability, and usability -the dependent variables; internal complexity was characterized by modeling system requirements with Software Cost Reduction dependency graphs, then quantifying model attributes using 15 graphtheoretical metrics the independent variables. Dependent variable data were obtained by having 32 subjects run simulations of our research test vehicle: the light control system (LCS). The LCS simulation tests used a cross-over design. Subject perceptions of these simulations were obtained by using a questionnaire. Canonical correlation analysis and structure correlations were used to test hypotheses 1 to 3 - the dependent variables predictability, observability, and usability do not correlate with the NAT complexity metrics. Five of 15 metrics proposed for NAT complexity correlated with the dependent data. These 5 metrics had structure correlations exceeding 0.25, standard errors < 0.10, and a 95% confidence interval. Therefore, the null hypotheses were rejected. A Wilcoxon signed ranks test was used to test hypotheses 4 to 6 - increasing NAT complexity increases system predictability, observability, and usability. The results showed that the dependent variables decreased as complexity increased. Therefore, null hypotheses 4 to 6 were rejected. Lastly, this work is a step forward to operationalize NAT for safety-related computer systems; however, limitations exist. Opportunities addressing these limitations and advancing NAT were identified. Lastly, the major contribution of this work is fundamental to scientific research - to gain knowledge through the discovery of relationship between the variables of interest. Specifically, NAT has been advanced by defining and quantifying complexity measures, and showing their inverse relationship to system predictability, observability, and usability.

By P. L. Loyselle, B. D. Comilsen, D. H. Carlson, J. H. Johnson

"In-mine airborne particulate samples have been successfully collected and the relative amounts of diesel and coal determined using the Laser Raman Quantitative Analysis (LRQA) method. This method allows analysis of filters which have been collected by a method similar to that used to determine the airborne respirable dust concentration in us underground coal mines. Samples were taken near the feeder-breaker, on haulage vehicles, and in the returns. Sampling methodologies were developed for coal-only and diesel-only particulate reference samples with sufficient filter loading for the LRQA method. A statistical analysis of reproducibility has been carried out. Samples have been collected simultaneously at two locations using the LRQA and the size-selective sampling methods. Good agreement between the two methods has been found.INTRODUCTIONThe goal of this research has been to develop the Laser Raman Quantitative Analysis (LRQA) method to measure the composition of respirable particulate, i.e. the fractions of coal and of diesel particulate, in the mine ambient air. In earlier Bureau of Mines sponsored research, we successfully demonstrated that the LRQA method could be used to measure the fraction of Diesel Particulate Matter (DPM) in coal/diesel particulate mixtures which were prepared in the laboratory.(I) 'The immediate objective was to test and refine this LRQA method on samples collected in a diesel underground coal mine.Specific objectives required to meet this goal include:I) Develop in-mine sample collection methods which will insure sufficient particulate loading on filters for LRQA. ,2) Develop methodology for in-mine collection of reference samples (""coal-only"" and ""diesel-only"" filters) which arc required for quantitative LRQA. 3) Analyze precision and accuracy of the LRQA method. 4) Compare composition measurements with another analytical method, i.e. the University of Minnesota/Bureau of Mines size selective sampling Micro-Orifice Uniform Deposit Impactor (MOUDI) method.An advantage of the LRQA method is that it allows analysis of filters which have been collected by a method similar to that used to determine the respirable dust concentration in US underground coal mines. No new sampling instruments and techniques are required. Transfer of sample from collection substrate to analysis substrate is not necessary. Furthermore, other analyses can be made on the same sample since the technique is nondestructive."

Jan 1, 1988

By H. B. Freeman, E. J. Gleim

During the 12 months ended July 1, 1931, engineers of the Bureau of Mines examined electrical equipment in 80 bituminous-coal mines. The purpose of these examinations was to ascertain the condition of such equipment with respect to possible hazards of gas and dust ignitions, also of shock. Although only 3 of the 80 were being worked with open lights and therefore did not use explosion-proof equipment, there were others where electric cap lamps were used by the men but where it was apparently assumed that conditions as to gas and dust did not require equipment designed to give protection against ignitions. Early in its history the United States Bureau of Mines originated certain standards covering the construction and testing of electrical equipment in order to minimize the dangers of ignitions from exposed electric sparks and flashes ; accordingly, it is comparatively easy to determine wherein a machine built to these standards falls short of continuing to meet them if damaged or neglected. Many so-called flame-proof and dust-proof machines, however, have not been built to any standard comparable with that developed by the Bureau of Mines. In addition, certain machines have parts which pass Bureau of Mines tests, but do not satisfy the full requirements in other respects, and others make no pretense of inclosing the spark-producing parts. It is not uncommon to find two or more of these various types in the same mine with " permissible " machines, the type that has been built to conform to the Bureau of Mines standard. Consequently, inspection of nonpermissible machines becomes somewhat difficult without a standard of comparison. Because of its unprotected condition obviously open-type electrical equipment must be used with great care, if at all, in a mine where precautionary measures are adopted in guarding against gas and dust ignition. The unsafe nature of such equipment is widely recognized. For that reason it is to be installed only where there is no likelihood of gas being present. It is not apparent to some, however, why flame-proof and dust-proof equipment and equipment having tested parts should not be regarded in the same light as permissible equipment.

Jan 1, 1932