Search Documents

By Gary P. Sames

Shale roof deterioration in coal mines. caused by ventilation air humidity fluctuations, is a common ground control problem. Shale roof deterioration often results in increased accidents, decreased production, inadequate ventilation, and increasing operating costs in maintaining haulage roads and airways. The results of Bureau of Mines research indicate that air tempering entries are an effective method of controlling deterioration prone shales. Some of the conclusions and recommendations drawn from Bureau research include (1) moisture sensitive shales will react adversely to moisture gains and losses, (2) the majority effect of specific humidity fluctuations can be concentrated in and absorbed by tempering entries, (3) tempering entry panels should be located as near to the main intake as possible, (4) tempering panels should be designed for a conservative recovery and provide a minimum of 20-to 30-min air residence time, (5) ventilation and escapeway requirements must be considered early in panel design, and (6) an efficient support and sealant plan can increase the life expectancy of a tempering panel.

Jan 1, 1985

By Richard D. Miller

The helium resources base of the United States was estimated by the Bureau of Mines to be 1,040 Bcf as of January 1, 1987. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 265 Bcf, (2) helium in probable natural gas resources, estimated at 228 Bcf, (3) helium in possible natural gas resources, estimated to be 320 Bcf, and (4) helium in speculative natural gas resources, 227 Bcf. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a separate classification. The depleting resources are those associated with natural gasfields that are, or will be, produced for the natural gas they contain. Almost all of the helium in potential (probable, possible, and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 951 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gasfields, are estimated to total 53 Bef. There is 36 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1988

By M. J. Sheridan

"INTRODUCTION In December 1942, the-Bureau of Mines reported favorably on a proposal to grant Government assistance-in constructing an access road (consisting principally of a timber-pile bridge across the Rio Grande at Hot Springs, N. Mex.) to the property under lease to the United States Fluorspar Co. At that time the property was being developed actively, and there appeared to be no immediate-need for exploratory or metallurgical assistance by the Bureau of Mines.Because milling facilities were inadequate; the access-read project was eventually disapproved, but prior to disapproval the company had discontinued operations. In June 1943, exploration was resumed by the Humphreys Gold Corporation of Denver, which had subleased the property. Difficulty of access continued to interfere with exploratory progress. In July 1945, at the request of the lessee, the Bureau of Mines directed sampling, using company employees.At the completion of this sampling program, the Bureau of Mines concluded that the property was potentially a important source of fluorite but that further development for production appeared to depend largely on the establishment, by exploration, of adequate reserves. Because of the relatively easy position-of metallurgical-grade concentrate and ores, it also was deemed advisable to investigate the possibility of producing acid-grade concentrate from the ore, for which a demand was becoming evident. Accordingly, a program of trenching, diamond drilling, and metallurgical testing was undertaken by the Bureau. The results of its investigation are reported herein."

Feb 1, 1947

By S. H. Katz

In the Bureau of Mines investigations of respiratory apparatus, a laboratory study of dust respirators has been conducted, and the results will be published in detail as a technical paper. Many industrial dust respirators, and many fabrics and filtering materials were tested. The principal results of these tests, and the conclusions drawn from them, are presented below. Reference to the patent literature discloses numerous types of dust respirators, mostly based on the filter principle. The present study included only representative filter-type respirators, purchased on the market.

Jan 1, 1926

By Steve Bessinger, Steve Signer, James Pile

The San Juan Mine and the National Institute for Occupational Safety and Health conducted a study to measure how development mining affected bolt loads. Twelve fully grouted, instrumented roof bolts were installed at two three-way intersections as part of the standard bolting pattern. Newly developed miniature data acquisition systems (MIDAS) were used to measure bolt load changes during initial face advance and cross-cut breakthrough. The effects of cut placement and depth on roof bolt loads were studied. This test showed how bolt loads increased at five positions along the bolt length during initial mining. Both entry advance and cross-cut breakthrough produced a similar percentage of increase in bolt loads. Geologic differences between the test sites were probably responsible for the differences in amounts of bolt loading. The test site with more top coal and a higher rock quality designation (RQD) had lower bolt loads.

By E. J. Gleim

This report describes a trip to Europe in the interest of safety in coal mines. It reviews the Eighth International Conference of Directors of Safety in Mines Re-search, which met in Dortmund-Derne, Germany, July 5-10, 1954, to discuss results of studies made in different countries to improve health and safety conditions under-ground. It also summarizes information on subjects of special interest in the United States gained by the writer in visits to mining experiment stations in Belgium, France, and England. The efforts being made to protect life and property underground were discussed, and ideas and experiences were interchanged freely, not only during the conference but also during visits to the several countries. Helpful information was obtained on many topics of interest, but time did not permit as thorough a discussion on some of them as might be desired.

Jan 1, 1956

By Ronald A. Vary

This paper is one of a series prepared by the United States Bureau of Mines dealing with milling methods and costs. In view of the current revival of interest in gold mining, information dealing with practices and costs in the development of gold properties is apropos. Milling practice at a small gold property in the prospect stage is described where, with a small outlay for plant and equipment, development has been carried on for about 20 months on the proceeds of the mill operation with little additional expenditure. The paper shows about what may be expected as to costs at a small property operated under northern climatic conditions and with rigid economy throughout the plant.

Jan 1, 1931

By R. D. Van Zant

The method for smelting zinc in horizontal retorts developed several centuries ago is still in use. This process consists essentially of the reduction of zinc oxide by carbon at 1,200° to 1,400° C. in a fire-clay retort. The reaction is highly endothermic, and a high radiation loss occurs in transferring the heat of reaction through the fire-clay walls. In recent years, silicon carbide retorts with much better heat-transfer characteristics than fire clay have been supplanting the old retorts. The practical impossibility of recovering the carbon monoxide formed in the reduction causes a large loss of fuel. Intermittent smelting is done in small retorts that are manually charged and discharged, and the furnace crews must be specially trained if efficient results are to be obtained. During the past 20 years several processes have been introduced that have substantially improved the horizontal-retort process. One of these, developed by the New Jersey Zinc Co., consists of a continuous process in which a briquetted mixture of zinc sinter, reducing agent, and binder is coked at 750° to 900° C. and charged into a vertical silicon carbide retort. A supply of displacement air or exhaust combustion gas is introduced at the base of the retort at an appropriate pressure in order to keep the zinc vapor from condensing on the cooled residue in the lower part of the retort. Any .oxidizing constituents in the displacement gas are converted to carbon monoxide by reaction with the carbon in the charge. The spent residue is continuously removed at the bottom of tl1e retort. The chief advantages of this process are said to be increased output per man-day, improved working conditions, high recovery of zinc, increased thermal efficiency, and long retort life.

Jan 1, 1950

By J. Koster

During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report.6/ The geology of the Marysvale region has been reviewed recently.7/ The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.

Jan 1, 1939

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979

By Robert L. Rough

The 1954 field tests consisted of six experimental shots in relatively deep holes in a sandstone similar to many oil-bearing sandstones. Water-injection measurements were made before and after each shot to establish the change in conductivity of the fluid caused by the shot. The pressure pulse produced by the shot was recorded in nearby holes to monitor the shot and to determine if any relation existed between the change in conductivity and the nature of the pressure pulse. The results of water-injection tests showed the range of conductivity of fluid before and after shooting with two different types of explosives. Because of the large spread in data for similar shots, not enough information was available to evaluate the differences in increased conductivity produced by the two explosives or any relation between the increased conductivity and the nature of the pressure pulse. However, these results, with the results of other tests involving explosive shots in rock, provide guidance for future research on the oil-well-shooting problem.

Jan 1, 1957

Reduce the exposure of diesel vehicle operators to diesel exhaust generated during mucking in deadend drifts. Approach Direct the diesel engine exhaust upward and rearward thereby using the thermal buoyancy of the hot exhaust to form a layer at the roof, above the breathing zone of the vehicle operator. Modifying the Exhaust Outlets Diesel front-end loaders used in nocoal mines to remove blasted ore usually operate in entries open only at one end to cross cut ventilation. These deadend drifts are not usually ventilated with the use of auxiliary fans and vent tubing because of frequent blasting. The existing ventilation, therefore, is usually poor, and a diesel engine operating in such a drift emits exhaust which is not immediately swept away from the operator. On most load machines, the diesel engine's exhaust outlet is located near the floor and directed downward or to the side, so that when the hot exhaust is emitted, it mixes with the mine air as it rises into the vehicle operator's breathing zone. In this way, a uniform concentration of diesel exhaust forms around the operator.

Jan 1, 1983

By R. E. Tremoureux

This paper describing the methods and costs of quarrying limestone at Sloan, Nev., is one of a series of similar papers being prepared for and published by the Bureau of Mines on this industry in the United States. These papers are designed to disseminate information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods Employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The quarrying operations at Sloan are interesting not only from a technical viewpoint and because of the magnitude of the deposit, but also because the quarry is located in a desert region far removed from the centers of population where lime is used. The quarry and plant are in Clark County, Nev., 20 miles west of Las Vegas, which is the nearest town to the site of the Boulder Canyon Dam. Sloan is on the main line of the Union Pacific Railroad connecting Salt Lke City and Los Angeles. The latter city is 280 miles from Sloan and it is the shipping, point for all supplies.

Jan 1, 1932

By Potts J. D.

Installation of a horizontal air-blocking shelf around the inside perimeter of the surface mining drill deck shroud is proposed to improve dust capture. Without the use of this shelf, a strong Coand? effect airflow pattern results in dust leakage to the environment, especially at the shroud-to-ground interface. Bailing air exits the drill hole and travels along the drill steel to the underside of the table, where it fans out across the bottom of the drill table and continues down the sides of the shroud. This dust-laden bailing air then strikes the ground and fans out under gaps between the shroud and the ground. The proposed shelf prevents dust-laden air from striking the ground by redirecting it toward the center of the enclosure, where it can be captured. Laboratory tests demonstrated that the shelf reduced dust levels outside of the shroud by 81% under operating conditions consisting of a 1.9:1 collector-to-bailing-airflow ratio and a 51-mm (2-in.) gap between the shroud and ground. The shelf was 152-mm (6-in.) wide and was located at a height equal to 2/3 the distance measured from the bottom of the shroud to the bottom of the drill table. The air-blocking shelf was also capable of overcoming the adverse impact of vertical leakage along the shroud seams as long as this leakage was confined to an area below the horizontal plane defined by the shelf location.

Jan 1, 2008

By Jon C. Volkwein

The U.S. Bureau of Mines has developed a method to measure methane and other gases during the auger mining of coal. An intrinsically safe commercial gas detector with a built-in data logger was mounted in the center of the hollow conveying auger. A sampling head through the wall of the auger conducted a gas sample to the detector. Results showed that gas levels can be monitored on a continuous basis during the auger mining of coal and the data retrieved upon completion of the hole.

Jan 1, 1994

By J. M. Mutmansky, R. A. Jankowski, M. A. K. Mohamed

"SYNOPSISKnown health hazards associated with the breathing of respirable dusts, particularly silica dust, during mining are becoming a great concern in many parts of the world. The search for effective and low cost dust control methods for underdeveloped countries will help in improving the productivity and keeping the mine environment safe. This article addresses the problem by providing suggestions concerning the easiest and most cost effective methods to control respirable dust in mining and mineral processing operations. INTRODUCTIONMedical BackgroundLung diseases caused by dust in mining operations have been recognized by mankind since the time of the Roman Empire. The writings of Pliny the Younger on natural history reported on maladies associated with dust in mining in the first century AD. However, no significant advances in controlling the lung diseases of miners came about for many centuries. The effects of mineral dusts were further described by Georgius Agricola in his sixteenth century book on mining (Agricola, 1556). After the appearance of Agricola""s book, lung diseases were more readily recognized, but the nature and severity of the ailments associated with mineral dusts could not be readily interpreted.In 1896, the discovery of x-rays by Roentgen advanced the diagnosis of lung diseases and the knowledge of what causes these diseases. In addition, the discovery allowed medical personnel some method of judging the extent and severity of the lung diseases in human beings. During the ensuing years, the term 'pneumoconiosis' became the common term to describe any of the diseases of the lung in which dust particles deposited in the lungs caused fibrous tissue and loss of some of the respiratory function. However, little in the way of social remedies for the diseases resulted until much later. Society was still not ready to act decisively to reduce the causes of lung disease due to the dusty conditions in the work place.Social action against lung diseases did not occur in the United States (US) until the 1930s. At that time, a tunnel driven through a sandstone mountain near Gauley Bridge. West Virginia, caused the death of several hundred workers due to acute silicosis, a severe form of pneumoconiosis caused by silica (Seaton, 1975). Dust conditions in this tunnel were quite bad, causing many of the workers to be subjected to extremely high silica dust concentrations. The severity of the disease in many of the workers became known to the public and prompted the US Congress and many of the states to enact laws to reduce the dust levels."

Jan 1, 1998

By Arthur M. Hartstein

The Bureau of Mines, through contract with Ultrasystems, Inc., obtained data on the oxidative degradative behavior of a number of materials used in coal mines. Tests were performed using a stagnation burner arrangement. Materials examined included those used in typical coal mining operations such as (1) polyvinyl chloride-containing materials. (2) neoprene compositions, (3) rigid foams (urethanes/isocyanates), (4) miscellaneous materials (including jute, fiber glass, and polyethylene), (5) coal, (6) fluids (phosphate esters, organic esters, oil-water emulsions), and (7) composites. The composite comprised a mixture of a phosphate ester fluid with (1) coal, (2) a representative polyvinyl chloride sample, or (3) a neoprene-type composition. A number of decomposition products are identified that could represent a potential health hazard to miners including HC1, CO, SO2 and H2S, if they were generated to exceed toxic levels.

Jan 1, 1974

By John C. Edwards

Chapman-Jouguet detonation calculations were carried out for pentaerythri-tol tetranitrate (PETN), TNT, and ammonium nitrate-fuel oil (AN-FO) explosives using the compressibility form of an equation of state of hard spheres based upon Percus-Yevick (PY) theory, and a chemical equilibrium detonation code called TIGER. Similar calculations were also carried out with the Becker-Kistiakowsky-Wilson (BKW) equation of state. For PETN, the BKW equation gives somewhat better agreement with experimental values of detonation velocity and pressure. However, in terms of experimental temperatures and concentrations of the minor product species (NO), the predictions of the PY equation are shown to be more satisfactory. Similar comparisons of experimental and theoretical results for TNT and AN-FO indicate that the PY equation has general utility in predicting the detonation properties of condensed explosives at moderate loading densities (Po < 1.3 g/cm3).

Jan 1, 1974

By W. H. Eddy

The Bureau of Mines conducted laboratory batch and continuous flotation processing tests on waste granite fines from South Carolina to determine the possibility of recovering high-quality feldspar and glass sand. Three flotation systems were used for removal of the iron-bearing biotite: Two employed an alkaline anionic-cationic circuit and the third employed an acid cationic circuit. Commercial-grade products were obtained when the remaining biotite was magnetically removed from the feldspar and quartz concentrates. Continuous flotation processing yielded a feldspar concentrate containing, in percent, 3.60 Na20, 5.60 K20, and 2.25 Ca0, with recoveries of 75.3, 66.6, and 72.6 percent, respectively. The feldspar tailing was high quality glass sand containing 98.0 percent Si02 and 0.025 percent Fe203; about 60 percent of the quartz was recovered.

Jan 1, 1972

By N. A. Gokcen

Equilibrium partial pressures of gaseous HCl and H2O over aqueous binary and ternary solutions of HCl and AICls were calculated or estimated in the range of 20° to 110° C, and up to saturation with AlC13?6H2O. The results were extended to solutions containing less than 10 wt-pct FeCl3 by assuming that FeCl3 and AIC13 are equivalent on the molar basis, since both salts have trivalent cations with a cammon anion. The ionic activity coefficient of HCl and the equilibrium constant for dissolution of gaseous HCl were also computed. This research is part of the effort by the Bureau of Mines, U.S. Department of the Interior, to provide thermodynamic data to expand the technology base relevant to the extraction of alumina from nonbauxitic domestic raw materials.

Jan 1, 1980