Search Documents

By F. P. Haver

The Bureau of Mines is developing a leach-electrolysis procedure to produce Special High Grade (SHG) zinc from sulfide concentrate without the generation of sulfur oxide gases. Chlorine-oxygen leaching of the concentrate yields zinc chloride (ZnCI2) which, after purification, is electrolyzed in a fused-salt cell to obtain molten zinc metal and chlorine gas for recycle. This paper describes a laboratory-scale investigation made to develop a procedure for electrowinning zinc metal from ZnC12. Zinc chloride by itself is not a suitable electrolyte because it fumes badly above its melting point and is a poor conductor of electricity. Other salts therefore must be added to prevent fuming and improve the conductivity. Optimum results were obtained with a KC1-LiCl-ZnCl2 bath at 500° C, using a current density of 5 amp/in2 and an electrode spacing of 0.5 inch. Under these conditions, SHG zinc was produced at a current efficiency of 94.3 pct and an energy requirement of 1.16 kwhr/lb. Fused-salt electrowinning eliminates the need to handle and melt cathodes and increases the production of metal per unit cell volume through the use of higher current densities than are possible with aqueous electrolysis.

Jan 1, 1976

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

On December 16, the General Services Administration (GSA) suspended weekly sales of surplus silver from the national defense stockpile because Congress approved the Defense Appropriation Act, which contained an amendment to halt silver sales. The amendment, introduced by Senator James A. McClure (R., Idaho), prohibits sales for 6 months while the impact of the sales and alternative methods of disposal are evaluated. The GSA sold 2 million troy ounces since sales started October 14. 46.5 million troy ounces were authorized to be sold during this fiscal year and an additional 58.6 million troy ounces were authorized to be sold over the following two fiscal years. The stockpile held 139.5 million troy ounces of silver when sales began in October. Brush Wellman, Inc., a vertically integrated producer of beryllium products announced plans to modify its Delta, Utah beryllium concentrate processing facility to utilize beryllium concentrates containing as little as 7% beryllium oxide. The company plans to invest $2.5 million for this modification with completion expected in mid-1983. Implementation of this plan to consume lower grade beryllium minerals will significantly increase world reserves of beryllium concentrates.

Jan 1, 1981

By Tobias W. Goodman

The U.S. Bureau of Mines used a contact drilling strategy with short-collared assemblies in order to rotary drill long horizontal methane drainage holes in the Beckley Coalbed near Glen Daniel, WV. By decreasing the thrust, and increasing the rotation of the drill bit when in contact with the roof and floor rock, assemblies with 1-ft (0.3-m), 10-ft (3- m), and 144 (43-m) long collars were made in deflect and stay in the coalbed. Successful application of this procedure resulted in holes drilled full length in coal with the original assembly including bit. The test assemblies deflected away from the original bearings of the holes during drilling and arced. Four holes were drilled to depths ranging from 478 ft (145.7 m) before the strategy was developed, to 4,034 ft (1,230 m) when the strategy was applied. Total length of the holes in coal was 8,590 ft (2,618 m). After 577 days the total methane captured by the holes was 221,600,000 ft? (6,276,000 m3). The methane flow rate peaked at 805,000 ft3/d (22,798 m3/d), then decreased to stabilize at 670,000 ft?/d (18,974 m3/d) after 6 months.

Jan 1, 1989

By Ernest A. Curth

The Bureau of Mines studied pressure changes in coal pillars by using encapsulated hydraulic pressure cells to measure relative changes in stress developed during mining. The data indicate that (1) abutment stresses were detected when the pillar line is within 42 to 100 feet, (2) vertical pressure increases as coal is mined in the pillars, (3) at first pressure is higher at the edge of the pillar than in the core, but as mining progresses, the higher pressure is measured in the core of the stump, and (4) in the two instances where lateral pressures were measured, they remained lower than the vertical pressures during pillar extraction. The data also indicate that the mean vertical pressure increase, 6P, in a pillar is roughly related to the percent of pillar extracted, A, by the empirical parabolic equation

Jan 1, 1967

By K. Shimamoto

This study has been prompted by the anticipated demand for rhenium by the petroleum industry and the concern for an adequate supply of rhenium to meet the demand. The present and projected outlook for rhenium relative to its distribution and occurrences, the recovery factors involved in ore beneficiation, capital and operating costs, changing technology, and the projected uses and market growth of rhenium are presented in this report as part of the Bureau of Mines program to determine the availability of recoverable rhenium in a developing market.

Jan 1, 1973

By R. V. Ramani, J. Qin, R. A. Jankowski

"Longwall mining is generally recognized as safer, more productive and economic when compared to room and pillar underground coal mining. There has been, however, increasing concern for the control of airborne coal dust concentrations in long wall faces. The airborne dust cloud at a longwall face is a complex aerosol system containing particles of varied size, density, shape and state of aggregation. For the development of more effective dust control practices in longwall faces, it is necessary to understand more clearly the characteristics of the longwall dust cloud.In this paper, results of a research study on dust concentration distributions along longwall faces are presented. The objective of this study is to characterize the longwall dust cloud behaviour and provide necessary fundamental data for a better understanding of the longwall dust problem. MSA personal samplers and gravimetric total dust samplers were employed to collect respirable and total airborne dust samples. The size distribution of these samples was determined by MicroTrac SPA. The instantaneous respirable airborne dust concentrations were recorded using RAM-I. The dust concentrations are related to face operations, particularly the shearer location and activities. The size distribution of airborne dust, instantaneous respirable airborne dust concentration, and air quantity distributions along longw all faces reveal a complex dust flow phenomenon. Additional fundamental studies are needed for characterizing the temporal and spatial behaviour of the dust cloud at longwall faces.IntroductionModern mechanized longwall mining was introduced in the United States in the 1960's and has become more common in the last twenty years. United States longwalls are multiple-entry retreating faces. According to a recent survey, 91 of the 102 longwall faces employ double-drum shearers (1). Several recently installed longwall faces have consistently produced over 4 000 to 5 000 tons per shift over extended periods of operation. The trend in under-ground coal mining in the U.S. certainly is toward the introduction of longwalls. This trend is true not only for new mines but also for renovation of existing mines. While longwall mining has many advantages over other mining methods, including improved safety, such as higher pro-duction. greater productivity and enhanced reserve recov-ery, it is associated with severe problems of dust control. The increase in longwall production has been accompanied by an increase in respirable dust problems which limit realizing the full potential of the longwall mining system. Despite the efforts to develop improved equipment and operational procedures to control the dust levels at longwall faces, it is still difficult to bring several double-drum shearer operations into compliance with the Federal stand¬ards of 2,0 mg/m 3 respirable dust without loss of produc¬tion. In fiscal year 1987, fifty-eight of the longwall sections were found to be in non-compliance once, and an additional 31 were cited two or more times'''. If the full potential of the longwall mining method is to be realized, new measures must be implemented to control the dust concentration to mandated levels. There is a need for detailed and extensive sampling of longwall faces to understand the dust source-sink relationships and the transient ambient concentrations. These must be related to the mining activities on the face. This paper is to characterize the longwall dust cloud behavior through a series of experiments in operating faces and provide necessary fundamental data for further studies to develop improved dust control practices."

Mar 1, 1992

By S. M. Shelton, F. D. DeVaney, M. M. Fine

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced ; although it is well -known that there are large deposits of low - grade ore in the United States , the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to obtain adequate supplies from foreign sources . Consequently, a program of laboratory and pilot - plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines . This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program . The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series , Report of Investigations 3606 , Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent , and C. H. Schack . Other reports will be published as the work progresses .

Feb 1, 1942

By B. H. Clemmons

A field method has been devised for rapid determination of heavy minerals occurring in the unconsolidatod beach and dune sands. The method has been proved practical by usage in field evaluations of several hundred beach- and dune-sand samples in the Florida area. The simple equipment required and the techniques involved are described. Other data show that the method is relatively insensitive to variations in the mineralogical content or size distribution of the mixed heavy minerals contained in the samples tested. A modification of this procedure, found to be suitable for plant use in determining the relative purity of heavy-mineral flotation concentrates, is also described. A specific application is determination of the amount of feldspar-quartz in spodumene flotation concentrates. The results of the rapid evaluation techniques closely approximate those obtained by more precise laboratory procedures.

Jan 1, 1957

By E. G. King

THIRD-LAW entropy data for zirconium-containing compounds are sparse. Kelley a lists entropies at 298° K. for the oxide, tetrachloride, nitride, and silicate, as well as for the metal. The present paper presents heat capacities between 51° and 298° K. and entropies at 298.15° K. for the zirconates of the alkaline-earth metals-calcium, strontium, and barium. The authors believe magnesium zirconate does not exist as a stable compound at room temperature. Entropies of formation from the constituent oxides also are given. MATERIALS The materials used in this investigation were synthesized and analyzed in the Berkeley Laboratory of the Bureau of Mines. Calcium zirconate was prepared by heating an intimate mixture of reagent-grade calcium carbonate and pure zirconia for 30 hours between 1,200° and 1,300° C. and for 32 hours between 1,400° and 1,500° C. As part of the heating schedule, the sample was ground and mixed seven times. Periodic analyses and minor adjustments of composition were made. Analysis of the final product gave 31.19 percent calcium oxide (theoretically 31.28 percent) and 68.67 percent zirconia (theoretically 68.72 percent). The X-ray diffraction pattern agreed with that in the ASTM catalog.

Jan 1, 1960

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years ago were only laboratory curiosities.

Jan 1, 1941

By G. B. Botsford

In August 1943 the Bureau of Mines began an investigation of the West Portal magnetite mines, which comprise the Swayze and Turkey Hill properties. The work included (1) traversing with a dip needle to record magnetic anomalies, (2) diamond drilling, and (3) sampling old mine dumps; it was completed in April 1944. The deposit consists of two parallel veins, which strike northeast and dip southeast. They carry magnetite in gneiss and schist. The Swayze mine was discovered in 1867 and closed in 1889, while the Turkey Hill mine was opened in 1872 and closed in 1887. The dip-needle survey covered 266 acres. The diamond drilling comprised 11 holes totaling 4,910 feet from which 142 samples were taken for chemical analyses. Old mine dumps were sampled at 52 points for chemical and magnetic analyses.

Jan 1, 1948

By D. L. Paulson

The Bureau of Mines used 50-and 800-kva electric-arc furnaces to confirm the feasibility of producing ferronickel in electric-arc furnaces from pre-reduced concentrate from the Yugoslavian FENI project. The relationships were established among metallic iron concentrations (degrees of prereduction), ferronickel grades, and nickel recoveries. Smelting the concentrate containing 1.27 wt-pct nickel and metallic iron levels between 2 and 3 wt-pct, produced 15 to 20 pct ferronickel. Higher or lower metallic iron concentrations were compensated by adding oxide pellets or carbon to the electric-arc furnace charge. Over 90 pct of the contained nickel was recovered when up to 20 pct ferronickel was being produced. Data obtained while smelting 16 tons of prereduced concentrate in the 800-kva electric-arc furnace indicated ferronickel can be recovered at an energy consumption of 530 kwhr/ton of prereduced material.

Jan 1, 1977

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years a ago were only laboratory curiosities.

Jan 1, 1941

By Harold J. Barnett

In January 1948 , the Secretary of the Interior directed that a study be made of energy resources and requirements that would provide a basis for continuing appraisal of the adequacy of the Department's programs in the energy field . That this instruction was timely has been demonstrated by the increasing interest being evidenced by Congress , industry , labor , and the public in the future of the energy segment of our national economy . Several studies of individual energy sectors have appeared . Various legislative proposals have been made in Congress for obtaining more information on this subject . Substantial interest in energy projections is not , of course , a recent innovation . Energy availability and consumption are strategic factors in peacetime prosperity and growth and in our national defense as well . The past generation's literature of earnest public discussion and of legislative consideration of matters involving energy projections is very extensive . This is an exploratory study produced in the Program Staff of the Office of the Secretary of the Interior in the first half of 1949 and revised recently to take account of certain of the preliminary energy data from the 1947 Census of Manufactures and critical comments . It is offered at this time solely as a technical contribution in economic research technique . As the Bureau of Mines has recently undertaken to revise this preliminary study , critical and other comments are invited .

Oct 1, 1950

By John R. Troxell

"INTRODUCTION Lookout Mountain is the natural barmier that isolates Dade County from the rest of Georgia. Legend has it that Dade County seceded from the Union long before the rest of the State of Georgia and did not officially return until July 4, 1945.Coal mining began in the Lookout Mountain area in 1891, and by 1894 production amounted to about 1,000 tons daily. Present production by the two principal operating companies is about 3,600 tons monthly.In the Sand Mountain area, coal has been mined intermittently since before the Civil War, and probably 6,500,000 tons has been produced.The Bureau of Mines coal project was initiated to alleviate a possible coal shortage and to assist the State in developing coal deposits to supply State institutions and local markets. Drilling began January 1, 1945, and ended May 11, 1945, after 2,907 feet had been drilled. By this time the Georgia Power Co. became interested in northwest Georgia coal fields as a possible source of more economic fuel for their steam-driven power plants, but the Bureau continued to act in an advisory capacity to the power company until June 30, 1945."

Oct 1, 1946

By Albert E. Long

Preliminary experiments conducted in 1949 with a few diamond bits in which the diamonds in the bit crowns were set in hard-vector directions indicated that a substantial saving could be effected when a high percentage of the diamonds were oriented in this-manner. It was realized, however, that many additional tests would have to be performed before a positive trend could be established and the possibility of coincidence eliminated. Therefore, a long-range series of experiments was planned to investigate various phases of the problems related to the orienting of diamonds in diamond bits. This report (the third in a series) 2/3 presents the information obtained from tests conducted to investigate more fully the effects of orienting high-grade drill bort in diamond bit crowns. In these tests, the drill bort were oriented in both hard-vector and soft-vector directions in the crowns of AX-size bits. Test drilling was done in a dike of saussuritized dacite porphyry similar to a fine-grained granite in hardness e drillability.

Jan 1, 1954

By William R. Wayment, David E. Nicholson

A modified percolation - rate test is proposed for use in determining flow rates through hydraulic backfill ; in contrast to the conventional test , a percolation- rate versus void - ratio relationship is established . requirements and a detailed test procedure are described . Equipment Results of a conventional test are compared with those of the proposed modified test . The proposed modified test method yields more accurate , realistic , and usable percolation- rate ( permeability ) data . The significance of obtaining accurate percolation rates for use in analyzing waterflow through hydraulic backfill is discussed .

Jan 1, 1964

By Robert F. Randolph

Research on improving haulage truck safety, started by the U.S. Bureau of Mines, is being continued by its successors. This two-part article reports the orientation of the renewed research efforts, beginning with an update on accident data analysis, the role of multiple causes in these accidents, and the search for practical methods for addressing the most important causes. Fatal haulage accidents most often involve loss of control or collisions caused by a variety of factors. Lost-time injuries most often involve sprains or strains to the back or multiple body areas, which can often be attributed to rough roads and the shocks of loading and unloading. Part II will describe research to reduce these accidents, including improved warning systems, shock isolation for drivers, encouraging seatbelt usage, and general improvements to system and task design.

Jun 1, 1997