Search Documents

By Douglas A. Crum

The Taylor's friction circle method for slope stability analysis can be extended to incorporate multiple circles defining the slip surface in a failure mechanism so that it is a workable method for bearing capacity calculations of foundations and rotational failures of retaining walls and similar structures. The U.S. Bureau of Mines has further extended the multiple-circle method to include friction in the material strength and to utilize computational schemes such that this method can be programmed with optimization capabilities rather than being used as a graphical or semigraphical method. Some examples are given that demonstrate ultimate bearing capacity calculations of embedded foundations with eccentric loads and nearby slopes.

Jan 1, 2010

By B. J. Moore

This Bureau of Mines publication reviews U.S. helium resources as of January 1, 1973. These resources, estimated to be 693.7 billion cubic feet, are broken down into four classifications, as follows: helium in storage, 34.9 billion cubic feet; helium in measured helium-rich natural gas reserves, 119.5 billion cubic feet; helium in measured helium-lean natural gas reserves, 62.8 billion cubic feet; and helium in indicated or undiscovered natural gas resources, 476.5 billion cubic feet. The helium in undiscovered natural gas is considered a national resource; however, this gas may not be discovered depending on many factors beyond the scope of this paper, and most of the helium in natural gas will be dissipated as the gas is consumed for fuel and other purposes.

Jan 1, 1976

By G. W. Elger

The Bureau of Mines conducted laboratory and larger scale studies on samples of domestic perovskite and ilmenite ore concentrates to devise a procedure for recovering TiC from these ores. From the concentrates, mixtures of titanium and calcium carbides were produced. The carbides were then ground and reacted with water. This reaction decomposed the CaC2 to acetylene and hydrated lime and simultaneously liberated the TiC. Using a combination of elutriation and gravity-separation techniques to separate the hydrated lime, approximately 93 pct of the titanium was subsequently recovered as purified carbide containing 54 to 70 pct titanium with CaO content as low as 0,6 pct. This combination of techniques can be used to separate more than 90 pct of the CaO from the TiC. Therefore, this carbiding procedure is a viable method for treating titaniferous materials, including perovskite, that contain more than 20 pct CaO. Tests made in a static-bed reactor showed that for the reaction of TiC with elemental chlorine to produce titanium tetrachloride (TiCI4), a temperature of at least 940° F is desirable to achieve a suitable extraction of titanium in a laboratory chlorination reactor. In fluidized-bed tests at 840° F, 98 pct of the titanium contained in TiC was extracted.

Jan 1, 1980

By L. A. Morley

Volume IV of the final report examines the problem of indirect contact of overhead high-voltage power lines by mining personnel. This refers to the contact of energized lines by workers through some intermediate conductor such as a metallic tool or a piece of high-reaching mobile equipment, thus the term "indirect contact." The shock hazard presented by such contact has been a major cause of electrical fatalities associated with mining operations. The report volume is divided into three major areas. The first gives a general background of overhead lines, basic characteristics, and associated hazards, and continues to describe presently used techniques and devices which attempt to alleviate the contact problem. The second area narrows the discussion to the mining industry by presenting a detailed analysis of 39 overhead-line contact accidents in mining since 1970. The third major section uses the information from the first two areas to formulate recommendations to prevent these accidents and subsequent electrocutions at mining operations.

Jan 1, 1982

By Howard D. Jacobs

A bulk sample of oxidized taconite taken from the western Mesabi Range was evaluated by the Bureau of Mines using the Bureau-developed selective flocculation-desliming-cationic (or anionic) flotation process. The raw ore sample containing 32.3 pct Fe was treated by both cationic and anionic flotation. Using the cationic system the concentrates averaged. 37.2 wt-pct of the feed and contained 62.8 pct Fe and 4.7 pet Si02 with an iron recovery of 72.3 pet. With the anionic system, concentrates averaged 37.7 wt-pet of the feed and contained 63.0 pct Fe and 5.3 pct 8i02 with an iron recovery of 73.5 pct. A comparison of reagent costs showed that the cationic process cost 144.1 cents per long ton of crude ore and the anionic process 178.7 cents per long ton of crude ore. Reclaimed water comprised 86 pct of the total water requirement for anionic flotation and 88 pct for cationic flotation. The ore used in this study was one of three samples representing about 3.25 billion tons of oxidized taconite containing from 32 to 36 pct feed iron. Previous study had indicated that selective flocculation-desliming-cationic flotation would produce concentrates from the other two samples of 61.7 pct Fe and 5.1 pct Si02 at 67-pct Fe recovery, and 63.5 pct Fe and 4.3 pet Si02 at 8S-pct Fe recovery. By developing a successful treatment for these ores, the Bureau has insured the availability of technology for processing an amount of raw iron ore which, by itself, would supply U.S iron needs for 50 to 75 years at expected consumption rates.

Jan 1, 1981

By J. H. Field

Results of studies by the Federal Bureau of Mines on a pilot-plant scale for removing hydrogen sulfide and carbonyl sulfide from gas mixtures by the hot carbonate system are given in this publication. Gases containing up to 10 pet. hydrogen sulfide and 48 grains carbonyl sulfide per 100 cu.ft. were treated. In most tests carbon dioxide also was present and was removed simultaneously with the sulfur compounds. Because the rate of absorption of hydrogen sulfide is much more rapid than that of carbon dioxide over a wide temperature range, selective removal of hydrogen sulfide occurred in the bottom section of the absorber near the point of gas entry. Hydrogen sulfide was removed to pipeline specifications with carbonate solutions by using split-stream flows in the absorber and regenerator.

Jan 1, 1960

By Franklin H. Persse

Domestic bismuth supply was projected from production figures for the ores in which it occurs--copper, lead, zinc, and tungsten. Published and unpublished data concerning host ores were examined to determine bismuth reserves and resources, and mine production. Potential recoverable bismuth occurring with reserves and resources of copper, lead, and zinc was estimated to be 36.3 million pounds. A bismuth availability diagram was developed from quantity estimates and ratios of production cost to value for these host ores. Additional recoverable bismuth occurring with domestic tungsten reserves was estimated to be 1.5 million pounds. Domestic byproduct production of bismuth will approximate 1.3 million pounds annually by 1980. This quantity will provide about 37 percent of the 3.5-million-pound estimated requirement for that year. Known world supply of bismuth appears to be sufficient for world demand to the end of this century. The study indicates that bismuth reserves and potential resources in the rest of the world have not been adequately reported.

Jan 1, 1970

By R. F. Stevens

A laboratory method for examining crude shale oil is described. The method uses only about 500 ml. of sample and a limited number of analytical determinations. Results provide information on the general characteristics and composition of an oil and serve as a basis for comparing different oils. However, the method does not provide for direct estimates of yields of commercial products. Analyses of 10 oils produced in the United States by different methods of retorting and of 10 shale oils from commercial-scale operations in 6 foreign countries are given. The shale-oil-analysis method presented in this paper is based on and employs the same equipment as the Bureau of Mines routine method for analyzing crude petroleum. As shale oil contains groups of compounds not generally found in petroleum, several modifications of the petroleum method that might increase its suitability for application to shale oil were investigated. The modifications included in the present method take into account the apparent poor heat stability of shale oil and the presence of large quantities of olefins and nitrogen compounds.

Jan 1, 1952

By Wendell R. Peters

Shallow underground voids resulting from early coal mining and other resource recovery activities over the past several decades are now being recognized as a significant cause of ground subsidence problems in developing urban areas. Uncertain knowledge of abandoned coal mines also imposes potential hazards in coal excavation operations since water inundation or the release of methane gas is a pricnipal hazard when mine excavation operations break into an abandoned mine. U.S. Army requirements for an effective method for detecting and mapping subversive man-made tunnels have resulted in a surface-operated automatic earth resistivity survey system with a digital computer data processing system. Field tests aimed at demonstrating the system performance resulted in successful detection of tunnels having depth-to-diameter ratios up to 15 to 1. Under the sponsorship of the Bureau of Mines, a similar system was designed and constructed for use in the detection of coal mine workings. This report discusses the hardware and software aspects of the system and the application of the high-resolution earth resistivity method to the survey and mapping of abandoned coal mine workings. In the field tests reported, the targets of interest were both air-filled and water-filled workings.

Jan 1, 1980

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Sidney Katell

This Bureau of Mines study estimates capital investment, operating costs, and selling prices for three underground bituminous mines producing coal with annual production ranging from 1.03 to 3.09 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of November 12, 1973, under the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 indexes. Initial capital investment ranges from $12,938,200 for the 1.03-million-ton-per-year (MJ.Vl tpy) mine to $31,435,500 for the 3.09 MM tpy mine. Total capital investment ranges from $21,607,200 to $51,982,000 for the same mines. Corresponding selling prices for the coal range from $9.11 to $8.06 per ton, assuming a 12-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1974

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By O. C. Blade

A comparison of certain properties of the commercial aviation gasolines produced in the United States during October 1949, 1950, and 1951 is presented in table 1, the 1951 data being average values from tables 3 through 6 of the present report. Trends in the average values of certain characteristics of these fuels may be seen in figures 1 through 4 which also indicate the minimum and maximum values. As may be observed, with the exception of changes in kinematic viscosities, the properties of commercial aviation gasolines have not varied greatly during recent years. A list of aviation-gasoline survey reports published by the Bureau of Mines is given on page 6. A summary of the average values of the properties on jet fuels is shown in table 2.

Jan 1, 1952

By W. T. Benson

The nickel-bearing laterite deposits in the Pine Flat and Diamond Flat areas, Del Norte County, Calif., were investigated by the Bureau of Mines to determine the extent and nickel content of the two deposits and the amenability of the ores to metallurgical treatment. The work was based on drill-hole sampling and metallurgical tests in which attrition scrubbing and sizing, reduction roasting, and magnetic separation were used. Results of the sampling indicated that the deposits are comparatively small and are marginal or submarginal in grade. Metallurgical tests showed that no separation of cobalt from nickel and iron was made by sizing; however, a large portion of the chromium was separated. Reduction roasting and magnetic separation did result in upgrading the iron, nickel, and cobalt, and the simultaneous rejection of chromium.

Jan 1, 1963

By G. V. Sullivan

This report summarizes the results of a preliminary study concerning manganese extraction from low-grade dolomitic materials from the Philipsburg district in Montana by the Dean-Leute ammonium carbamate process. Studies were made to determine the relationship between the variables involved in treating these materials by a roast-leach process and the amount of manganese extracted. The variables studied were the roast temperature, the roast particle size, the molar ratio of NH3 to CO2 in the leach solution, the liquid-solid ratio in leaching, the leach time, and the size of the particles being leached. The roast-leach studies were statistically designed, and the experimental results were evaluated by an analysis of variance.

Jan 1, 1962

By Gennaro G. Marino

The Bureau of Mines and the University of Illinois investigated surface characteristics and damage to structures from mine subsidence over a room-and-pillar coal mine in Hegeler, IL. Data on three adjacent subsidence sags and associated structural damage were collected, summarized and evaluated. The subsidence sags developed over a 10-year period and took place above a modified room-and-pillar operation mining the Herrin (No. 6) coal at a depth of 130 to 135 ft. Surface vertical displacements of 3.0 to 3.5 ft resulted from extracting 6.1 to 6.4 ft of coal. Ground movements associated with sag formation severely damaged three houses and a radio station building, broke numerous utility lines, and structurally distorted three radio transmission towers. The radio station was remodeled and the towers repaired, but the three houses were subsequently demolished. Surface waters collecting in the subsidence depressions caused failure of radial ground transmission systems. The following subsidence profile characteristics were determined at the radio station and one of the houses, respectively: profile slopes, 0.02 and 0.07; maximum curvatures, 2.3 x 10-4 ft-1 and 3.0 x 10-4 ft-1; and angular distortions, 6.6 x 10-3 and 62.0 x 10-3. Although the house was more severely damaged than the radio station, both structures are classified as severely to very severely damaged.

Jan 1, 1986

By Henry E. Blake

The Bureau of Mines has been engaged in a continuing research effort to develop processes for increasing the recovery and utilization of fluorine from low-grade resources. This current research has shown that over 98 percent of the fluorine in phosphate rock is extracted when the ore is treated with excess phosphoric acid in the presence of water vapor at 150° to 180° C. More than 80 percent of the fluorine can be recovered as fluosilicic acid, which can then be converted to commercially useful hydrogen fluoride or fluorspar by previously developed Bureau processes. Extraction of P205 from the ore was about 98 percent in batch tests and 90 percent in semicyclic tests.

Jan 1, 1974

By D. E. Redmon

Linear programing provides a mathematical technique by which activities can be planned in such a way that an optimal result is obtained. Routine applications of linear programing require only a knowledge of algebra. However, a complete understanding of the fundamentals of linear programing requires a knowledge of advanced mathematics. The purpose of this publication is clarification of terminology and illustration of applications in comparatively simple mining problems. Two mining situations are considered: Mine stopes from which ore is to be produced at a minimum production cost; also, uranium mines from which ore is transported to one mill, a maximum monetary value is desired. The details of data arrangement for solution by linear programing are described and the solutions are presented. Results of these solutions indicate successful applications of linear programing to mine production scheduling.

Jan 1, 1964

By A. J. Kraemer

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the on the districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of eight. California crudes. Analyses of other crude oils from California have been published it Reports of Investigations 2595, 2608, and 2846. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting 65 samples was facilitated by the courtesy of representatives of oil companies in California. The methods used in testing and analyzing the samples are described in detail in Bureau of Mines Bulletin 207. A discussion of the interpretation of crude-oil analyses, as made by the Bureau of Mines, is given in Bureau of Mines Report of Investigations 2806.

Jan 1, 1931

By W. L. Eaton

This report is the second in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Wyoming Basin of the Northern anthracite field is presented. The first report I.C. 8274, published in 1965, was a catalog of microfilmed maps of mines in the Eastern Middle anthracite field. Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1968