Search Documents

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Jan 1, 2008

By John A. Organiscak

Enclosed cabs are a primary means of reducing equipment operators? silica dust exposure at surface mines. The National Institute for Occupational Safety and Health experimentally investigated various factor effects on cab air filtration system performance. The factors investi­gated were intake filter efficiency, intake air leakage, intake filter loading (filter flow resistance), recirculation filter use, and wind effects on cab particulate penetration. Adding an intake pressurizer fan to the filtration system was also investigated. Results indicate that intake filter efficiency and recirculation filter use were the two most influential factors on cab penetration performance. Use of the recirculation filter reduced cab penetration by usually an order of magnitude over the intake air filter alone because of the multi­plicative filtration of the cab interior air. Intake air leakage and filter loading affected the cab penetration to a lesser extent, while wind had the least impact on cab penetration between the calm and 10-mph wind velocities tested. Adding an intake pressurizer fan notably increased intake airflow and cab pressure with only minor changes to cab penetration. A mathematical model was developed that describes cab penetration in terms of intake filter efficiency, intake air quantity, intake air leakage, recirculation filter efficiency, recirculation filter quantity, and wind penetration.

Nov 1, 2008

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant coalbeds in Russell County , Va . Almost 2 million tons of coal was mined in 1961 ; 75 percent of the coal was cleaned mechanically in preparation plants in the county . The coal of Russell County is ranked as medium- to high- volatile bituminous , contains small amounts of sulfur , and generally requires some cleaning to reduce the ash content to limits acceptable for metallurgical purposes .

Jan 1, 1963

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions5/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1961

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1968

By C. A. Komar

The Bureau of Mines has undertaken an investigation to determine possible applications of acoustic energy at sonic and ultrasonic frequencies to improve ultimate recovery from oil reservoirs. A literature search was conducted to provide background information for initiating laboratory research. The purpose of the literature search was to review the uses that have been made of acoustic energy in the petroleum industry and to select procedures and techniques that could be applied to the solution of petroleum production problems. The characteristics (68)3 of ultrasonic energy make it potentially useful to a variety of industrial and experimental applications. Pulse techniques (99) are common in the testing of materials where inspection is accomplished by propagating an ultrasonic pulse through the material. Viscosity measurements (45) are made by interpreting changes in the absorption of sound as it is propagated through a flowing liquid. Cavitation phenomena (93) produced by high-intensity ultrasound in liquids have been used extensively in industrial cleaning, machining, impact grinding, and aluminum soldering operations.

Jan 1, 1963

By B. W. Gandrud

In July 1948, the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and mine operators, published Report of Investigations 4306, "A Combination Cleaning and Dewatering Process for Treating Fine 'Sizes of Coal, Preliminary Report In this report a new process, referred to as kerosene flotation; was described, and results of experimental work with the process Previous to the fall of 1947 were given, The contents of the report. were summarized on pages 19 and 20' as follows: In coal-preparation plants using wet methods of cleaning, the most difficult problem is the cleaning and dewatering of the "fines" from about 10-Mesh to 0. A combination proceed is now under investigation that shows promise of practically and feasibly solving this problem. The process is similar to froth flotation, but a generous quantity of kerosene is used as one of the reagents, and the feed is from approximately 10-mesh to 0 considerably coarser than the usual froth flotation feed. The kerosene and the coarseness of the reed result in a floated product that, under certain circumstances, can be dewatered satisfactorily by a simple process of mechanical squeezing, Squeezing is accomplished by means of an ordinary conveying' Auger-and trough assembly with a section of pipe easing at the outer end of the trough. The bottom of the trough and. casing is fitted with wedge-wire sections to permit escape of the water freed by the squeezing action of the auger. On account of the important role of the kerosene, the process has been referred to in this report as kerosene flotation. Up to now, the investigative work has been divided about evenly between the laboratory and commercial plants. Nearly all of the work has been done on sludges containing the solids from the underflow of dewatering screens. A few runs have been made on 10-mesh to 0: fines from raw coal, but in some of those runs the dewatering mechanism, failed to function.

Jan 1, 1950

By Lloyd Williams, R. E. Hershey, B. W. Gandrud

"1. The investigation shows that the Sewanee bed is the only bed of major importance in Marion County, 97 percent of the coal mined in the county having come :from this bed. There are coal reserves in minor quantity in the Battle Creek bed, and production from this bed depends on a few small truck mines. The Richland bed, or Lower Sevanee has been mined in the past, but no coal has been produced from it in late years. There are no production records of any other beds in the county, although some coal has been produced from them.2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on l,800 tons per acre-foot of coal in place, are estimated to be 61 million short tons as of January 1, 1953. Of this total, 55 million short tons is in beds 28 inches and more thick. Areas in each bed ·were omitted from the estimate where available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.3. Recoverable reserves of coal are estimated in beds 28 inches and more 'thick. This recovery is based on total thickness of coal in the bed (less partings 3/8-inch thick or more), rather than on the thickness of the coal actually mined. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian Region. The combined weighted average recovery for the Sewanee and Battle Creek beds in Marion County, as determined by this investigation, is 60.9 percent. Based on this, the recoverable reserves of coal in Marion County are estimated at 34 million tons."

Oct 1, 1955

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.2 The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; 1960, 5.3 feet; and 1965, 5.2 feet.3 Table 1 includes data on number and production of bituminous coal and lignite mines classified by 1-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, 1960, and 1965. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness--less than 2 feet to more than 50 feet--a large majority of the production, 62 percent in 1965, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1967

By Franklin D. Slagle

Porosity and bulk-and sand-grain-density values were determined for 2,040 core samples of 30 formations from 47 wells in New York, Ohio, Pennsylvania, and West Virginia, and are compiled for petroleum industry use in well-log evaluation and geologic studies.

Jan 1, 1967

By M. R. Geer

Full-seam mining with continuous mining machines in dirty coal beds may increase loss of coal in the washery refuse. At one mine mentioned in this report the loss of salable coal was increased sixfold. Cleaning trials were made on three samples of jig refuse in a dense-medium pilot plant to demonstrate the application of this process to the recovery of coal from waste. These tests demonstrated that coal could be separated from impurity with the same degree of sharpness obtained in treating raw coal by dense medium. However, the recovery efficiency achieved in treating refuse averaged distinctly lower than that possible with raw coal because of the greater proportion of intermediate-density material in the feed and the lower yield of clean coal.

Jan 1, 1955

By L. T. MCELVENNY, Robert B. McElwaine, M. Clair Smith

Production of mercury from the cinnabar deposits of the southwestern Arkansas mercury district began in 1931 , reached its peak in 1942 , and ended in 1944. The mines are now idle . Virtually all the cinnabar was obtained from deposits in a belt , about a mile wide , of steeply dipping sandstone beds in the overriding blocks of three thrust faults . The belt was productive for a length of about 27 miles eastward from eastern Howard County, through Pike County, into Clark County . During the early life of the district, Federal agencies watched and recorded its progress as a contributor of a strategic metal, and later, during the war, conducted investigations designed to advance its development . In 1941 , the Bureau of Mines and the U. S. Geological Survey cooperated in investigations on eight mineralized areas in the western part of the district , to wit : Hales mine , U. S. mine , Lulu Bell property, Hopkins Hill , East Gap Ridge , Gap Ridge , Parnell Hill , and Section 17 mine area . U. S. Geological Survey prepared both surface and mine maps and designated the areas to be investigated ; the Bureau did the drilling , trenching, and sampling involved in the investigations . Twelve holes , aggregating 3,539 feet of bore , were diamond drilled on six properties ; 5,309 linear feet of surface trenches were bulldozed in six areas and 19 samples taken from them ; and 86 underground channel samples were cut in two adits on one property . In 1944 , the Bureau of Mines measured mine dumps and calcine dumps in the district in an investigation of their mercury content . Two mine dumps and one calcine dump were sampled . The data pertinent to the work done by the Bureau are included in this report .

Oct 1, 1950

By J. A. Cavallaro

This Bureau of Mines report describes the preparation characteristics of 10 coal samples collected from the significant coal-producing mines of Lucas, Mahaska, Marion, Monroe, and Wapello Counties in Iowa, with special emphasis on physical desulfurization. All 10 samples were of high sulfur content as received, ranging from 4.2 to 10.4 percent; the organic sulfur content ranged from 0.8 to 3.8 percent. The pyritic sulfur content of the samples could be appreciably reduced by crushing and washing and provided pyritic sulfur reductions ranging from 36 to 75 percent. Crushing to 3/8-inch top size and removing the sink 1.60 specific gravity material would provide float coal products containing 3.5 to 6.0 percent sulfur. However, these coals could be burned at utility plants utilizing SO2 removal processes with efficiencies ranging from 70 to 88 percent and still be in compliance with the current Federal SO2 emission regulations for stationary sources.

Jan 1, 1973

By W. S. Sanner

Seven samples were analyzed from the major reserves of the Bottom Red Ash bed, Northern anthracite field. The data show variations in thickness and geo-logic structure and in the amount of coal that can be recovered. Recovery of market-grade (less than 17 percent ash) coal is high for all samples, ranging from 76 tp 95 percent in the 3-1/4-by 9/16-inch sizes. The occurrence of coal containing less than 5 percent ash varies from 19.5 to as much as 57.5 percent. Crushing the coarse sizes to minus 9/16 inch increased recovery of market-grade coal in six of seven bed samples. Crushing released sufficient impurities to cause substantial increases in yield of coal containing less than 5 percent ash for all samples. Analyses of the float coal indicate that the quality of coal is comparable for all samples.

Jan 1, 1967

By W. A. Stickney, J. W. Town

Batch and continuous - circuit flotation , leaching , precipitation , and electrodeposition studies were made by the Bureau of Mines to determine optimum conditions for treatment of complex mercury - antimony sulfide and mercury- arsenic sulfide ores and concentrates . On the Red Devil ore sample over 95 percent of both the mercury and antimony sulfides were recovered in a flotation concentrate containing 35.6 percent mercury and 21.0 percent antimony . By selective flotation a mercury concentrate containing 71.0 percent mercury and 2.9 percent antimony was obtained with a mercury recovery of 90.4 percent . Leaching results show that , with 150 grams per liter of sodium sulfide and 50 grams per liter of sodium hydroxide , 95 to 99 percent of the mercury , antimony , and arsenic sulfides could be extracted from the concentrates treated . Sodium hydroxide reagent consumption was based on the sulfides generated in the dissolution of the sulfide minerals and on the method of metal recovery used . Selective leaching of the antimony and arsenic sulfides with potassium sulfide dissolved more than 95 percent of either of these two sulfides and 0.5 to 5 percent of the mercury sulfide present . Methods for recovering mercury and antimony from solution were electrodeposition of mercury followed by electrodeposition of antimony , aluminum precipitation of both mercury and antimony , or antimony precipitation of mercury followed by antimony electrodeposition . The method used in recovering the mercury depended on the mercury- antimony content of the solution being treated .Batch and continuous - circuit flotation , leaching , precipitation , and electrodeposition studies were made by the Bureau of Mines to determine optimum conditions for treatment of complex mercury - antimony sulfide and mercury- arsenic sulfide ores and concentrates . On the Red Devil ore sample over 95 percent of both the mercury and antimony sulfides were recovered in a flotation concentrate containing 35.6 percent mercury and 21.0 percent antimony . By selective flotation a mercury concentrate containing 71.0 percent mercury and 2.9 percent antimony was obtained with a mercury recovery of 90.4 percent . Leaching results show that , with 150 grams per liter of sodium sulfide and 50 grams per liter of sodium hydroxide , 95 to 99 percent of the mercury , antimony , and arsenic sulfides could be extracted from the concentrates treated . Sodium hydroxide reagent consumption was based on the sulfides generated in the dissolution of the sulfide minerals and on the method of metal recovery used . Selective leaching of the antimony and arsenic sulfides with potassium sulfide dissolved more than 95 percent of either of these two sulfides and 0.5 to 5 percent of the mercury sulfide present . Methods for recovering mercury and antimony from solution were electrodeposition of mercury followed by electrodeposition of antimony , aluminum precipitation of both mercury and antimony , or antimony precipitation of mercury followed by antimony electrodeposition . The method used in recovering the mercury depended on the mercury- antimony content of the solution being treated .

Jan 1, 1964

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute, and the Bureau of Mines of the United States Department of the Interior. This paper is a continuation of a series made in cooperation with the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC), Inc. The first of this series of reports presented data on motor gasolines sold during the winter of 1935-36, and succeeding reports described motor gasolines sold during the summers and winters to and including the summer of 1941. No reports were made on motor gasolines sold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed

Jan 1, 1948

According to industry representatives, U.S. producers were listing unalloyed 95.5 percent aluminum ingot in October at 53-57.5 cents per pound, but reportedly much is being priced at 53 cents. New York dealers raised their October positions by about 3 cents to 56-56.5 cents, mainly to cover spot supply shortages. London Metal Exchange 3-month forward contracts traded up in October from 52.3 to 57.3 cents per pound and closed at 56.4 cents. ASBESTOS The Jaquays Asbestos Corp. has announced the imminent closure of its mine and mill in Globe, Arizona. This is the last asbestos producer in the State having operated continuously, except during the early thirties, since 1914. Cost of compliance with environmental regulations was given as the reason for closure.

Jan 1, 1978

By O. C. Blade

This report on the properties of motor fuels sold through service stations-in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Deparment of the Interior. It presents analytical data for 4,397 samples, representing the products of 130 companies. The samples were collected during December 1952 and January and February 1953. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor-Gasoline Survey reports published during the past ten years is given on page 5.

Jan 1, 1953

By Charles N. Speltz

Coal resource data from public and private sources, in conjunction with previously published data, were used by the Bureau of Mines to determine the location and extent of strippable coal resources in Colorado. Total strippable resources of approximately 18 billion tons were estimated in 12 separate coal regions, fields, or deposits. Coal recoverable by contour mining techniques was not included. Criteria used in defining strippable resources were a minimum coalbed thickness of 2 feet and a maximum overburden thickness of 150 feet, except where the coalbeds are of exceptional thickness. Ail Colorado coal is either Cretaceous or Tertiary in age. Cretaceous coals occui In the Dakota Sandstone, the Mesaverde Group, and equivalent formations while Tertiary coals occur in the Dawson Arkose, the Fort Union and the Wasatch Formations, and equivalent formations. The strippable coal ranges in rank from bituminous in the Yampa region to ligniferous in the Denver basin. Ali this coal is low in sulfur content (less than 1 percent); ash content is low to high; heating value ranges from 3,000 to 12,000 Btu's per pound. Ash from the lignite of the Denver basin was found to contain an abnormally high percentage of kaolinite which conceivably could be recoverable as alumina.

Jan 1, 1976

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grind-ability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1965