Search Documents

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By Merle L. Bowser

The Bureau of Mines has constructed a miniature oxygen deficiency alarm system using an electrochemical cell as the sensor. Distinct audible signals are produced at either of two preselectable oxygen levels which can be varied from approximately 10 to 20.9 percent oxygen. The high or cautionary range produces a 500-cycle-per-second tone pulsed at about a 1-cycle-per-second rate, whereas the lower or more dangerous oxygen level produces a continuous 500-cycle-per-second tone.

Jan 1, 1968

By Joan K. Kuenzi

The purpose of this U.S. Bureau of Mines information circular (Ie) is to discuss how job analysis methods taken from different disciplines can be used together to form a more complete picture of jobs in the mining industry. "Job analysis" is a term used by many researchers, but use of the term is far from standardized. Authors of papers on this subject often state that there is confusion in how or why jobs are to be analyzed, what the resulting information is to be used for, and what the "job analysis" actually means. The process of breaking a job into elemental tasks and analyzing them is used to determine what skills and knowledge are needed to perform a given job, to improve efficiency, and to develop safer job procedures. All are valid reasons to analyze jobs, but the methods used to accomplish the analyses may be very different. In order to create a more complete picture of a job, it may be useful to incorporate methods and information from different areas of study rather than choosing one method for analysis.

Jan 1, 1995

By D. R. Mathews

The Bureau of Mines investigated the effects of tungsten and chromium, separately and combined, on improving the mechanical properties and oxidation resistance of vanadium. Binary and ternary vanadium-base alloys were prepared and tested for oxidation resistance and tensile strength. Softening occurred with less than 1 weight-percent of either tungsten or chromium, followed by strengthening with higher alloying contents. Vanadium alloys containing up to 9.8 weight-percent chromium or 14.1 weight-percent tungsten were more resistant to oxidation in air at 600° C than unalloyed vanadium. For the alloys with 12.20 weight-percent chromium or 14.56 weight-percent: tungsten, the maximum concentrations used, the lower yield strengths were about twice that of 38,600 psi for the unalloyed vanadium. Recrystallization temperatures for these alloys were 100 and 150° C higher, respectively. Alloys containing both chromium and tungsten had properties similar to those of the vanadium-tungsten alloys.

Jan 1, 1967

By L. E. Dalverny

This Bureau of Mines report describes the deployment, 5-month operation, and lessons gained from a continuous gas monitoring system using sampling-tube bundles at an underground mine fire in West Virginia. Research information gained indicates the utility of relating certain gas concentration ratios to events during fire development, mine reventilation, and mine recovery. In addition to monitoring the quality of remote fly ash seals, the system provided timely warning of dangerous gas concentrations which developed during surface and underground recovery activities. An evaluation of system components is supplemented by recommendations for improvements.

Jan 1, 1975

By R. L. Grant

"Carbon dioxide has been used for extinguishing electrical fires of many kinds (1, 3, 4) 3/ and more recently has been applied to some extent in fighting coal-mine fires (5). This report is concerned with the possibility of an electric current being conducted from a live power source, such as a trolley wire, across the impinging spray of carbon dioxide gas, to a metallic discharge nozzle, and then being grounded through the body of the person holding or touching the container. Rose and. Skinner (5) have described a case in which a fall of roof coal had brought down the trolley without creating a dead shot. The current was conducted in part through the loose coal to the rail, causing ignition of the coal. The fire was successfully extinguished with carbon dioxide.Dielectric data on pure carbon dioxide gas and liquid have been reported by Quinn and Jones (2). For the gas, the dielectric constants range from 1.00971 (35°C., 10 atmospheres) to 1.3072 (70°C., 151 atmospheres); for the liquid, 1.6016 (0°C., 50 atmospheres). Compared with the dielectric constant of air (1.0006, 1 atmosphere), these data, indicate that carbon dioxide in both gaseous and liquid forms is a very poor conductor of electricity, of the same order as air. 4/"

Aug 1, 1942

By J. Bender

The objective of this research was to (1) Further develop cyanobacteria mats' for metal-tolerance and cold-tolerance, (2) test them for durability in the field environment and (3) assess them for metal sequestering potential with actual and simulated field samples. Results show that mats performed well In the field and effectively sequestered metals from actual and simulated field samples. Metal uptake from Iron Mountain Hine samples was for Ins 87%, Cu and Cd 99%, Initial concentrations (mg/L) were Zn = 3,250, Cu , 279, Cd = 28. In solutions simulating the Gulf Tunnel drainage, Zn and Mn were effectively removed by mats immobilized on glass wool. Effluent water, after treatment, generally had a Ph of 7 .5-8.5. Al though the final metal concentrations in the mats 'harvested from the decontaminated water were only 1% or less, the actual mechanism of metal deposit was probably a mat-mediated alteration of the environmental conditions causing the metals to deposit outside the mat as oxides or carbonates. Bioflocculents, released by the mats, were likely involved in the metal-removal process.

Jan 1, 1996

Objective To identify techniques to reduce the probability of gob gas explosions. Background In the last 6 years, seven explosions of methane and/or coal dust occurred within worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many mine seals and caused much damage external to the sealed area. Three of these gob gas explosions occurred in one mine in Alabama over a 3-year period. Fortunately, the explosion forces and the toxic gases that vented from the sealed gob area did not cause fatalities or injuries, but they destroyed several large seals. If miners had been inspecting or working near these areas, the potential for serious injury and/or death would have been high. The United Mine Workers of America and the Mine Safety and Health Administration (MSHA) requested that the National Institute for Occupational Safety and Health (NIOSH) help identify the mechanisms for lightning penetration into the gob and recommend ways to reduce the probability of occurrence of future explosions from such lightning penetrations into sealed areas of underground coal mines. Because three of the explosions occurred in a single mine, special attention was focused on these particular explosions. The first occurred in April 1994 in a sealed area, which enclosed about 1.35square miles of abandoned workings (gob). This explosion destroyed 3 of the 38 seals that surrounded the gob. These seals were less than 2,000 ft away from three 4.5-in-diam steel-cased test wells that extended from the surface into the mine entry. At the time of the explosion, the National Lightning Detection Network (NLDN)verified 12 lightning strikes within 10 miles of the mine, including several above the gob. After the 1994 explosion, the damaged seals were rebuilt using an acceptable seal design capable of with standing a 20-psi explosion, as required by 30 CFR 75.335. On January 26,1996, a second gob explosion destroyed five more cementitious pumpable seals less than 2,000 ft away from those destroyed in 1994and even closer to the steel-cased wells. The NLDN verified72 lightning strikes in the area of this second gob explosion. Compressive strength analyses of fragments from the destroyed seals showed that strengths ranged from 11 to 138 psi, with an average of83 psi. This is over 100 psi below the minimum 200-psi compressive strength requirement for cementitious pumpable seals. These seals were again replaced. On July 9, 1997, the third and most violent explosion occurred in the same vicinity of the last two explosions. Three more cementitious pumpable seals were destroyed, including one newer seal that exceeded the minimum 200-psi compressive strength requirement. The NLDN verified 695 lightning strikes above the mine during the time in which the explosion occurred. MSHA's

May 1, 2001

By L. C. IlsLey

So many subjects are covered in State mine-safety regulations that any attempt to compare different State laws in their entirety would be futile. On the other hand, if one selects a single phase or branch of safety work, such a comparison may prove profitable. The subject selected for study in this paper is limited to legislation or regulations dealing specifically with safeguarding (electric) motored equipment used in gassy mines. T When one reads glowing accounts of the safety activities being carried on here and there it is easy to believe that everything which is right and proper is being done to safeguard the mine.workers; but, when one takes time to look into the weakness of many State regulations, it is evident that there is still room for improvement. Undoubtedly it would have been much better for the safety of mines if electrical equipment had been introduced into mines 50 years earlier. If electricity had been in general use when the first mine regulations were pre- pared, those formulating the rules would have covered this hazard along with other hazards, but as electricity came in at a later period, safe mine legisla- tion regarding it has been woefully neglected. Today the United States in general is far behind most other coal-producing nations in the provision of adequate safety rules or laws for the installation and maintenance of electrical equipment and wiring. Returning to the subject of our study, approximately 30 of the 48 States mine coal. More than 20 of these States' produce coal in large quantities. How- ever, of the 30 States only four, 3 Pennsylvania, Utah, Washington, and West Virginia, have laws which specially call for the use of explosion-proof types

Jan 1, 1929

By Ludwig Schmidt

The consumption of gasoline in the United States varies materially with the seasons; during some of the summer months it exceeds the rate of production and in the other seasons the production of gasoline exceeds the consumption, The usual practice of the larger refiners is to store surplus stocks during the winter season in order to meet the heavy demands during the summer months. The following table shows the stocks of gasoline at refineries on the last day of April for the past five years: 1919 593,616,170 gallons 1920 643,5526644 " 1921 747,222,900 " 1922 892,567,766 " 1923 1,336,417.871 "

Jan 1, 1923

By S. P. Kinney, P. H. Royster, T. L. Joseph

An investigation of the production of iron in the blast furnace is obviously not an easy subject for research . Enough is known of the mechanical , thermal and chemical conditions existing inside the furnace to say certainly that they are complicated. Furnace operators have found that the process is sensitive to a number of known and to many unknown operating conditions . In order to form any conclusions of value , it seems necessary to collect a large amount of data taken with considerable care and accuracy. These facts make a blast furnace research difficult but not impossible . The most serious obstacle in attacking the problem comes from the fact that it is useless in the design and operation of the blast furnace to use the method of " trial and error , which has proved valuable in so many other industrial problems . The variables are so interrelated and are so dependent one on the other that the number of experimental combinations to be tried is enormous . There are certainly not less than twenty factors in furnace operation and design that are known to influence the results . This is apparent if it is remembered that a phrase like " size and shape of the furnace" includes height of the furnace , height , diameter and angle of the bosh , inwall batter , stockline diameter , and furnace volume ; and that a phrase like " chemical and physical properties of the fuels charged " includes size and shape of the lumps , density, porosity and strength of the coke , in addition to its chemical analysis . Let us suppose that we need choose for each of twenty factors one of two values , for example , suppose we must say only that the furnace shall be " tall " or " short , " that the bosh angle shall be " flat " OF "steep , that the ore shall be " coarse " or " fine , " or that the blast has to be "hot" or " cold , " the number of resulting combinations is more than one million . In putting twenty pennies on the table , either heads up or tails up, the number of permutations possible is the twentieth power of two , slightly more than one million. It is obvious , therefore , that some sort of mathematical relationship , a set of rules of thumb , laws , curves or the like , are needed . Whether the relationships , curves or formulas are derived from experiment , from theory, or from mere guess -work, makes no difference provided they agree with the known facts . If they do not agree with known facts , they are worthless no matter what their origin or how weighty the " authority" vouching for them. Few such relationships have appeared in blast- furnace literature , and it may be doubted whether such formulas can be discovered .

Sep 1, 1923

By Fred Kissell

The Bureau of Mines has developed the shearer-clearer--a new type of dust control system for longwall shearers. The system partitions the airflow around the shearer into a clean split and a contaminated split. The dust cloud is confined to the vicinity of the coal face, while the shearer operators remain in the clean split on the gob side of the machine. The shearer-clearer operates on the principle that each water spray moves air like a small fan and can be positioned to direct the dusty air towards the face. The hardware is inexpensive and can be installed in a single shift. It consists of several strategically mounted water sprays and one or more passive barriers. Laboratory testing indicates reductions 1n shearer operator dust exposure as high as 97 pct. Preliminary results from an underground demonstration in one mine also indicate that considerable dust reductions at the shearer may be obtained. In conjunction with the development of the shearer-clearer, dust surveys were conducted in three other mines to determine if some shearer spray systems currently in use partition the flow in a manner similar to the shearer-clearer, and if so, whether this partially accounts for markedly cleaner conditions on some longwalls. Results from these surveys indicate this to be the case. A feature of the cleaner longwalls was a downwind orientation of their water sprays, which is a key element of the shearer-clearer system. The shearer-clearer system described in this report was designed for an Eickhoff EDW 300 shearer working a 7-foot coal seam. The testing to date has concentrated on cutting directions counter to the primary airflow. The development effort continues for different mining equipment and conditions. It is expected that different systems will be required to accommodate the range of conditions occurring underground. Application of the system presented here to conditions different than those described is not likely to produce the same results.

Jan 1, 1981

By J. P. Coughlin

The U.S. Bureau of Mines has developed a monitoring system that acquires and analyzes data for use in determining the conditions that may precede mountain bumps in coal mines. Based on a UNIX workstation linked to an array of geophones in a working longwall operation, the system captures complete waveforms of microseismic events and simultaneously obtains continuous samples of the voltage levels of each geophone. Event rates and locations are calculated and displayed in real time on the UNIX workstation, which is situated in an underground instrumentation room. These results also are transmitted from the workstation to a display computer near the longwall face. The system runs continuously and has the capability to acquire, analyze, display, and archive microseismic (transient) data and single point data, such as closure and pressure changes, simultaneously.

Jan 1, 1993

By Russell R. Trengove

Core samples from an ore horizon 2,000 feet below the surface were successfully obtained by rotary drilling at the property of the Eureka Corp., Eureka, Nev. The ore was soft and friable; cores were not obtained previously with diamond drills. Whipstocking was used to get samples in a zone 200 feet from a vertical hole. A technique in shipstocking, by which the direction and deviation of the holes were controlled by means of nonfriction-type survey instruments, was successfully employed.

Jan 1, 1956

By I. S. Solet

This study, of the liquidus temperatures and densities of molten alloys of zinc and aluminum was made as part of a broader investigation on refining of scrap aluminum. One of the methods of refining involves the separation of liquid and solid phases by gravity segregation and by filtration. More accurate data were required on the liquidus temperatures and the densities of molten' mixtures of the metals than were available in the technical literature. New data on the liquidus curve were obtained by thermal analysis. The new temperatures are, for the most part) somewhat higher than those reported previously by other investigators. The density of molten mixtures of zinc and aluminum were found to be less than would be calculated by assuming that the two metals occupy the same respective molal volumes in solution as they do as pure metals.

Jan 1, 1949

By Lars Osen

This investigation was undertaken to contribute to the understanding of underground pull tests by conducting laboratory tests under closely controlled conditions. Steel bolts, instrumented with electrical resistance strain gages, were anchored in an aluminum block, a granite block, and a steel sleeve, and were subjected to pull tests. The bearing plates used were either flat7 dished, or embossed. In pull testing a bolt that is prestressed, there is a range of loading during which bolt load is greater than the jack-applied load, This study showed that preload, the size, shape, and type of bearing plate; and the geometry of the system determine the point at which bolt load and applied load become equal. The effects on bolt load of both a theoretical solution and actual pull tests were analogous and led to similar results.

Jan 1, 1965

By Charles H. Atkinson, Robert T. Johansen

Tremendous volumes of petroleum ( crude oil and natural gas ) at present cannot be recovered economically . The feasibility of using nuclear explosions for production stimulation therefore has been investigated . Data from underground nuclear tests conducted by the Atomic Energy Commission were reviewed , and the physical effects were evaluated for stimulating petroleum production . Calculations of the effect on ultimate recovery of increasing reservoir temperature with nuclear explosives showed disappointingly small increases . Production increases caused by fracturing of massive low- permeability reservoirs appear technically and economically promising . Petroleum reservoirs that might be converted from submarginal to commercial production are being located and evaluated as to potential reserves and as a location for a field test .

Jan 1, 1964

By D. J. Bauer, V. E. Shaw

Bastnasite concentrate was processed to recover total rare - earth content and obtain high - purity ceric nitrate . Reaction of the concentrate with 45 percent caustic soda for 1 hour at 180 ° C in stainless steel vessels resulted in 99 - percent conversion to rare - earth hydroxides . A drying step followed by solution in nitric acid produced a tetravalent cerium fraction amenable to extraction with TBP . Single- stage separatory funnel experiments resulted in 90 -percent recovery of ceric nitrate at a purity of 99.9 percent . Fractional extraction in pressure - bubbler columns resulted in 98.5 - percent recovery of 99.5 -percent - pure ceric nitrate .

Jan 1, 1964

By C. E. Reistle

[In producing crude oils of paraffin base and of mixed base the producer is often confronted with the problem of preventing and removing paraffin that settles out of oil and accumulates in the well. This paraffin consists of heavy waxes with some sand and asphalt, and varies in. consistency from a soft semifluid wax to hard gummy wax. This problem is by no means a new one as troubles have been encountered with it since the earliest days of the industry. However, with the discovery of the panhandle, Texas, field and other large fields in which extensive troubles have been encountered, the problem has assumed added importance. In new fields the most serious trouble with paraffin is in the flowing wells the paraffin accumulates in the casing and tubing of such wells and unless removed will completely plug the well. This condition also develops in wells which are produced by gas lift, and often presents a serious problem when, this method of producing the oil is used. In older fields paraffin is also deposited on the face of the producing sand that on the walls of the hale or within the interstices of the sand near the hole, and this materially affects the amount of oil that can enter the well.]

Jan 1, 1927

By L. G. Marshall

This report is one of a series published by the Federal Bureau of Mines describing mining methods and performance at individual operations throughout the United States. The objective of these papers is to promote development and conservation of our mineral resources by disseminating reliable technological information on mining methods, practices, and results that may be applied to the engineering analysis and solution of mining problems. SUMMARY Operation of a limestone quarry producing flux for the steel industry and crushed stone for production of concrete is described in this report. The deposit being mined is a flat-lying limestone formation under a thin overburden 2 to 25 feet thick. The height of the quarry face varies from 9 to 60 feet, averaging 40 feet. Production rate ranges from 4.5 to 5 million long tons per year.

Jan 1, 1959