Search Documents

By M. S. Oudenhoven

This Bureau of Mines investigation was conducted to obtain an experimental solution of stress changes in the vicinity of a circular opening in an infinite plate. Plates were stressed biaxially in compression and subjected, by four different-length shoes, to a uniform pressure at opposing points on the opening periphery. The principal stresses along the vertical and horizontal axes, which result from peripheral pressure, were obtained from the photoelastic analysis of four frozen-stress epoxy models. These principal stresses were then super-imposed on the mathematically determined principal stresses (along the same axes) obtained from a theoretical biaxial stress field in which the magnitude of the lateral pressure was one-third that of the vertical pressure. The results indicate that an increase in shoe length increases the radial compressive stress and the tangential tensile stress (except tangential compression at r/a = 1, which exists for all shoe lengths). Also, a partial control of the stresses within one-half radius of the opening surface is accomplished by a change in the magnitude and placement of peripheral pressure.

Jan 1, 1966

By Raymond M. Stateham

A portable, handheld infrared scanner has been used to detect abnormal surface temperature on dumps of flood-generated trash near Wilkes-Barre, Pa. Three of eight dumps examined had thermal anomalies on the surface, indicating temperature buildup at depth. The anomalies found with the scanner were verified by measurements with a thermocouple probe or a carbon monoxide detector. One week after the investigation was completed, open fire broke out at the site of one of these thermal anomalies; about 6 weeks after the investigation, a thermal anomaly in another dump was verified when a trench was excavated in the dump.

Jan 1, 1973

By Wm. W. Odell

A study of certain gas making and fuel problems peculiar to the gas industry of California has been made by the Bureau of Mines. The work was done at the request of, and in cooperation with The California Gas Research Council 2, for the purpose of obtaining basic information on the gas-making fuels available to California, and their applicability to the present and future needs of the gas industry in that State. The data obtained have been applied in outlining a construction program, and indicate the possibilities in efficiently utilizing fuels in making gas by other than the oil-gas process. This paper presents an outline of the study and a summary of the principal results obtained, with some of the more important conclusions and recommendations based on this data. Gas is produced in California by processes which are both unique and different from those common to other parts of the United States. The bulk of the manufactured gas is made in and distributed from two main districts which are centers of population - namely, the Los Angeles district and the San Francisco Bay district. The gas manufactured in the Bay district is, almost exclusively oil-gas, whereas that produced in the southern part of the State, where natural gas is available, is mostly mixed natural gas and reformed-gas, but oil-gas is the chief product when the supply of natural gas is inadequate. Practically all of the gas companies are equipped with oil-gas generating apparatus, and anticipate using it in the future. As the continued use of the oil-gas process to the exclusion of all other processes, depends upon a continued supply of oil at a low cost, and the prospect of obtaining such low-priced oil in the future is somewhat uncertain, the questions have arisen: What will the future gas-making process or processes be? When will it be necessary to make plans for the installation of different gas generating equipment, and what will that equipment comprise?

Jan 1, 1926

By George S. Rice, C. W. Owings

"Brattice cloth is an important material in coal-mine ventilation practically all coal mines use some brattice cloth, gassy mines a large amount. It is employed in three ways:Crosscut brattices.Curtains in haulageways.Line brattices in gassy mines.In each case brattice cloth is used to deflect part or all of a split of the mine ventilating current into or toward the face of a working place. As a general rule, its use in a particular location is temporary.A crosscut brattice should be employed only until a permanent stopping has been erected. Such a brattice is subject to little wear when in actual service, the chief damage occurring when it is taken down and put up again.When used for curtains on haulageways or haulage crosscuts to deflect the air current up into rooms or headings, the wear on brattice cloth is considerable, as mine cars, machines, and personnel constantly pass under the curtains which last only a few days or a few weeks in an active part of the mine. For such purposes tightly woven smooth cloth is desirable, so that it will not be easily torn. Curtains should not be used back from the working places, as they sometimes are, to deflect the main. split, as the leakage of air is too great. Doors should be used in such places."

May 1, 1928

By M. E. Kundick, W. E. Dieter, L. Cohen

The major details of design and maintenance of a seamless stainless steel fume hood system , developed by the Bureau of Mines , are described and illustrated . Operating and housekeeping routines are outlined .

Jan 1, 1964

By Herbert H. Fields

The Bureau of Mines has been promoting health and safety in mining since its establishment in 1910. One area of research covers methane control in coalbeds; this report describes a multipurpose borehole used for both degasification and the production of commercial-quality gas. The multipurpose borehole was drilled into a barrier pillar, and seven horizontal degasification holes and one pressure point hole were drilled radially out from its perimeter. On January 28, 1974, after 505 days of degasification, a compressor was installed to the exhaust stack of the multipurpose borehole (1), and pipeline--quality gas was introduced into a commercial pipe-line. As of February 4, 1975, over 171 million cubic feet of gas had been purchased by the gas company. The in situ pressure at a depth of 200 feet into the coalbed and the average gas flow and water flow from the degasification holes as they were completed and closed off were 203 psig, 1,200,000 cfd, and 6.8 gpm, respectively. Twenty-four hours after the seven holes were connected through individual pipes to the atmosphere, the total gas and water flows and the in situ pressure dropped, respectively, to 971,000 cfd, 1.3 gpm, and 18 psig. Five hundred days later, the corresponding values were 620,000 cfd, 0.15 gpm, and 10.5 psig. Daily flows have been as high as 800,000 cfd, and as low as 360,000 cfd, during the last 500 days. On February 4, 1975, after 882 days of degasification, 576 million cubic feet of gas had been removed from the Pittsburgh coalbed; apparently a much larger area of virgin coal is being degasified than is defined by the holes. This study indicates that horizontal boreholes drilled into a coalbed from the bottom of any shaft will effectively remove gas from the Pittsburgh coalbed,

Jan 1, 1975

By R. V. Rahfuse

Noncaking 0- by 2 -inch subbituminous coal from New Mexico was gasified with air and steam at 205 prig using a stirred-bed producer to determine coal losses by entrainment in the gas for this low-sulfur, high-ash coal which contained 20 percent particles smaller than 1/16-inch sieve size. The use of fine-sized coal has particular importance because most production from mechanized mines is smaller than 2-inch size. This initial attempt showed technical feasibility for gasifying New Mexico subbituminous coal containing small-sized particles in fixed-bed producers without excessive coal loss by entrainment. Dust loss averaged about 2 percent of moisture-free coal, most of which was recovered from the gas. Ash clinkering was controlled by adding 1,010 lb/hr steam to reduce tempera¬tures in the combustion zone. Yield of low-Btu fuel gas, 150 Btu per scf, dry, amounted to 69,800 scfh from 1,490 lb/hr coal (as received) and 3,450 lb/hr air (dry).

Jan 1, 1974

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By Richard A. Andre, R. Larry Grayson, Thomas Simonyi

"INTRODCICTIONThe search for the cause(s) of coal workers' Pneunoconiosis continues despite the vast amount of research that has been undertaken over the past forty to fifty years. Good correlation between the mass of dust inhaled over workers' lifetimes and the incidence of the disease has led to the development of effective environmental standards and implementation of good procedures for the control of dust generation and dispersion in the working place. Research has only begun, however, to uncover the biochemical mechanisms involved in initiating the disease.Correlation between the rank of the coal seam in which miners worked and disease incidence and severity is acknowledged worldwide, but the agents in the higher rank coal seams which cause CWP arc still not defined. The basic components of the coal seams, i.e., the elements and minerals, are generally known, but the way in which they interact with human pulmonary cells is largely still a mystery.The process of disease development is a biochemical one which depends on the characteristics of the pulmonary cells within their immediate biochemical environment and the characteristics of invading respirable coal mine dust particles, probably both chemical and physical ones. The cell-particle relationship, therefore, must be defined, and both cells and particles must be characterized according to properties which potentially are involved in the disease process.Following such characterization, specific respirable dusts from different coal seams, which appear to have different effects on coal workers, must be obtained or constructed and then used in experiments designed to determine dust toxicity or the response of animals exposed to the dusts.The results presented here focus on characterizing properties of respirable coal mine dust particles collected from operating longwalls in West Virginia and Virginia Longwall panels were selected for analysis because the respirable dust in the coal face areas is largely uncontaminated by rock dust and analysis of the dust yields results unconfounded by rock dust."

Jan 1, 1990

By W. J. Fene

Ventilation is undoubtedly the greatest single safety factor in the operation of a coal mine. Any condition or occurrence that interrupts the ventilating current or changes its normal course through the mine workings is a distinct hazard and should be considered as such by every coal-mine owner, operator, and worker. The hazard, of course, is much greater in a mine that is emitting gas, as an explosive mixture can accumulate in a very short period if the ventilating current is interrupted. It is common to find one or more entries producing 600 cubic feet or more of methane per hour. If the ventilating current were short-circuited from these entries for 15 minutes, there would be an accumulation of 150 cubic feet of methane, which, when mixed with enough air to dilute it to the lowest explosive point, would make about 3,000 cubic feet of explosive mixture; this gas could be ignited in almost any normally operated mine by a cutting machine or other electrical equipment. The ignition of this quantity of an explosive gas-air mixture can readily cause an explosion of coal dust that would completely wreck the underground workings and possibly some of the surface structures. In fact, the ignition of one-tenth of the above quantity of an explosive mixture of gas and air might readily start an explosion that would, extend through every part of a large mine. The possibility of occurrence of interruptions to the ventilating current has received comparatively little consideration from mine owners, operators, and workers in many parts of the United States. Such a possibility should be considered in connection with every mine that gives off explosive gas, and steps should be taken to prevent it.

Jan 1, 1943

By David C. Oyler

The Bureau of Mines is cooperating with the U.S. Department of Energy in a directional degasification project at the Emerald mine near Waynesburg, Pa. This project is designed to combine the highly successful underground horizontal degasification technology with surface drilling methods. The objective of this program is to demonstrate that directional drilling can be used as a technique for degasifying coalbeds ahead of mining to reduce the hazards of methane-air explosions in coal mines. The directional hole at the Emerald mine is designed to start vertically and enter the Pittsburgh coalbed horizontally. A 3-inch-pilot hole entered the Pittsburgh coalbed at a vertical depth of 999 feet. The hole will be reamed to 8-3/4 inches in diameter, and 5-1/2-inch casing will be cemented in place. Three individual 3-inch-diameter, 3,000-foot horizontal gas collection holes will be drilled into the coalbed in a "bird foot" pattern. A corehole and vertical dewatering hole have been completed at the anticipated coalbed intercept. The dewatering hole was drilled to 130 feet below the Pittsburgh coalbed, a depth of 900 feet, and 880 feet of 7-inch-OD casing was cemented in place. Seven vertical holes for monitoring the extent and progress of degasification have been drilled within the horizontal drilling area.

Jan 1, 1979

By D. J. Parker

Ability to signal the hoisting engineer in shaft mines is of utmost importance from the standpoint of safety and economy. The problem of signalling from the cages and especially from the moving cages has received too little attention from mine operators; however, this problem has been given considerable thought and attention by at least one large metal-mining company in Utah which has devised successful, economical, and safe systems of signalling from the cage whether it is moving or at rest. A Report of Investigations on "Methods used in Utah for signalling mine hoists from moving cages," by C. A. Allen, then a metal-mining engineer in the Bureau of Mines, was issued in June, 1920. As this report contains interesting history of systems of signalling from moving mine hoists, and describes several systems then in use, it is here quoted in full.

Jan 1, 1929

By E. L. Litchfield

Descriptions are given of the techniques and apparatus used by the Bureau of Mines for determinations of flat plate ignition quenching distance and minimum spark ignition energy. The descriptions include discussions of reaction vessel materials, shapes, and sizes and discussions of electrode configurations. Spherical, hemispherical, or flat plate electrodes are recommended. The preferred metal in electrodes and electrode supports is stainless steel; the flat plate electrodes incorporate flanges of low electrical conductivity which are most frequently formed from glass. Various aspects of the electrical energy supply system are discussed and suitable arrangements of components are indicated. The concept of a thermal relaxation time is introduced as a basis for the choice of a minimum interspark time during the testing of a gas mixture. The following indicate the varied conditions under which these tech were utilized: Mixture pressures between 10 mm Hg and 45 psig, initial temperatures between -78° and +198° C, and gaseous mixtures representing wide ranges of cL.. D reactivity and corrosiveness. Minimum ignition energies were determined which varied from about 10-7 joule to nearly 103 joule.

Jan 1, 1967

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By Allen D. Look

Use of two-way radio communication at the Santa Rita open pit of the Kennecott Copper Corp. has furnished a satisfactory answer to the problem of communications for an operation covering an extended area. Coordination of operations has resulted, with little loss of time in making changes during the shift. Repairs are facilitated, and safety of operations is increased through better control of blasting and hazardous conditions. INTRODUCTION Expansion of mining operations brings increasing needs of improved communications to coordinate the mechanized operations that contribute to the efficiency of present-day open-pit methods. Equipment found satisfactory when first installed becomes inadequate as distances and demands increase. It is the, purpose of this paper to record the progress being made by one mine in meeting this problem.

Jan 1, 1952

By D. E. Fogelson

In a factorial experiment, blasting caps were detonated in three sizes of shotholes in mortar with three types of stemming--dry sand, wet sand, and hydrostone. Free-surface displacement pulses were recorded with a capacitive-displacement gage at a distance of 15 inches. The effects of decoupling and the type of stemming on the amplitude and the duration of the displacement pulse were determined. Both the amplitude and the duration of the displacement pulse were significantly decreased by increasing the decoupling, but they were little affected by the type of stemming.

Jan 1, 1965

By W. D. Dietzman

This Bureau of Mines report presents a profitability analysis of producing crude oil by waterflooding. Included are the estimated costs of installation of water injection and producing equipment for waterfloods at 2,000 and 4,000 feet and the estimated annual operational expenses for each in west Texas. Using these cost estimates as a base for selecting a range of costs that are indicative of producing crude oil by waterflooding, a simulation technique was derived for determining the profitability under various conditions. Because of the large number of combinations of variables used in this study, a high-speed digital computer was utilized for the calculations. The variables include operational expenses, capitalized costs, price of the oil, annual production, and leasehold acquisition cost. The results obtained from the simulations are presented Fn the appendix. In addition, a nomographical approach was chosen for presentation of the profitability. Five nomographs are presented that can be used for fast estimation of the discounted cash flow (DCF) rate of return that might be expected from a prospective or active operation under various sets of assumed conditions.

Jan 1, 1974

By H. H. Schrenk

Much has been written and said concerning tables of permissible or maximum allowable concentrations of various toxic substances in air, but not enough attention has been given to their limitations and how to use them intelligently . There is a tendency to place too much reliance on figures , with little or no consideration of their real meaning . The repeated publication of a figure often adds significance to it far beyond that intended by the original author or publisher . How are these figures referred to as "maximum allowable concentrations " established? What is their real meaning? To answer these questions it is necessary first to define maximum allowable concentration . The usual definition is somewhat as follows : "The average concentration to which an industrial worker can be exposed for 8- hours daily for an indefinite period without injury or occupational disease . This definition is made up of the following items : ( 1 ) Average concentration, ( 2 ) 8 - hour day , ( 3 ) indefinite exposure period , and ( 4 ) lack of injury or occupational disease . There is some controversy regarding item ( 1 ) , items ( 2 ) and ( 3 ) are usually though not invariably accepted , and there is definite disagreement regarding the interpretation of item ( 4 ) . . To reach a more satisfactory interpretation of maximum allowable concentration , attention is directed to ( 1 ) the development of tables of maximum allowable concentrations , ( 2 ) criteria on which limits are based , and (3 ) methods used to obtain data on which limits are based .

May 1, 1948

The U.S. Bureau of Mines evaluated water-jet-assisted longwall shearers in full-scale laboratory tests and underground. Both test programs showed that use of high-pressure water did little to reduce the shearer motor energy required to maintain a given cutting rate. However, three other major benefits were achieved with the use of water-jet-assisted cutting. At a pressure of 1,800 psi, respirable dust levels were reduced about 80 pct compared with the dust levels of the conventional water spray system operating at 340 psi. Operating at higher pressures required for water-jet assist also resulted in an increase in the average size of coal cut, which translates into a decrease in product fines. Finally, although no controlled measurements of bit wear as a function of water pressure were made, mine personnel reported that the shearer bits lasted longer when water-jet-assisted cutting was used.

Jan 1, 1989

By John E. Pahlman

The Bureau of Mines investigated the feasibility of removing heavy metals from mineral-process waste streams by precipitation with lignochemicals and humic acids. Lignochemicals are by products from the paper industry, while humic acids are obtained by caustic treatment of peat, subbituminous coal, and lignite. These high-molecular-weight organic materials have many functional groups, which can coordinate and form innercomplex salts with heavy metals that are crystalline precipitates. Filtering of a humic-acid-or lignochemical-treated solution or waste stream containing these precipitates removes the heavy metal sequstrates. Tests were conducted with two lignochemical samples, three humic acid samples, lime (CaO), and sodium hydroxide (NaOH) in which increasing amounts of these additives were reacted with 50 mL of solution containing Fe3+ , Al3+, Cr3+, Pb2+, Cu2+, Cd2+, Zn2+, Co2+, Ni2+, Mn2+, and Hg1+. At the appropriate pH, greater than 90-and 99-pct removal was achieved for these 11 heavy metal ions from the 10-and lOO-ppm solutions, respectively, using lignochemicals and humic acids. Removal efficienC)' with these organic materials is better than that with CaO, especially for the more toxic ions, Hg1+, Cd2+, and Pb2+. Unlike the precipitates formed with NaOH or CaO, those with lignochemicals and humic acids are compact and noncolloidal. The volume of their sludge is sharply lower than that of the finely dispersed lime or soda precipitates; thus, their removal in settling tanks or by simple filtration is enhanced.

Jan 1, 1988