Search Documents

By Karl-Heinz Frohne

This report presents the findings of a study of a portion of the Clover-Rush Run oilfield located in Roane County, W. Va. The study was made to investigate the possibilities of secondary oil recovery in the Big Injun sandstone underlying the William Kaufman lease. Reservoir properties, original reserves, and primary oil recovery are also presented. The investigation is based on a core analysis and related laboratory tests, well records, field production data, and subsurface information from the Kaufman property. A theoretical primary oil recovery of 9.7 percent of original oil in place is predicted for the reservoir. A waterflood performance prediction of a hypothetical pilot area was made by use of a computer. The prediction showed that, based on laboratory oil water relative permeability curves, the water-injection time needed to initiate oil production is excessive and that the stabilized water-injection and corresponding oil-production rates are very low. This precludes waterflooding the reservoir on an economic basis. A prediction for secondary oil recovery by gas injection was attempted but could not be completed because essential reservoir data were not available. In July 1965, the lease operator initiated, and is currently conducting, a gas-injection program, but there had been no increase in oil production up to November 1966.

Jan 1, 1967

By F. X. Tartaron

This report describes work done by the Bureau of Mines to simplify the design and operation of the vortex cone, a new device for prerefining blast furnace iron. Three new apparatus arrangements were tested. Results with one of these arrangements average 74.2 pct silicon removal and 61 pet oxygen efficiency (disregarding removal of carbon and manganese).

Jan 1, 1965

By G. L. Gates

The Bureau of Mines in cooperation with the City of Long Beach) Calif.) studied some physical factors effecting the deposition of barium sulfate scale in oil-well rotary pumps. Freshly formed barium sulfate was obtained by combining sulfate in sea water with barium from a barium chloride solution. The rate of scale deposition was measured quantitatively by weighing the pump impellers and diffusers. The results of the tests showed that coating the impellers with plastic significantly reduced the rate of barium sulfate deposition.

Jan 1, 1967

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

By V. J. Lynch, A. L. Peyton

"INTRODUCTION AND SUMMARYThe Brewer mine, near Jefferson, Chesterfield County, S.C., was originally operated as a gold mines as late as 1890 this mine was reported to have been one of the large gold producers in the southeast,Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered by Pardee and Parks. 3/ of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.During the 1940's the Chemical Engineering Branch of the Tennessee Valley Authority and the Electrotecbnical Laboratory of the Bureau of Mines at Norris, Tenn., investigated topaz from the Brewer mine to determine the possibilities of its use as mullite and for the production of calcium fluoride.From July 1950 through. April 1951 the Bureau of Mines conducted a diamond-drilling project at the Brewer mine to determine the grade and extent of the topaz deposits. Ten diamond-drill holes, totaling 2,344 feet, were completed, and 231 analyses of core samples were made during the course of the project.This report presents factual data relating only to the diamond-drilling project, The placer deposits on the Brewer property were previously investigated by the Federal Geological Survey 4/."

Aug 1, 1953

By G. R. Hopkins

[A new record in fuel efficiency at petroleum refineries was established in 1939, when a the average e B.t.u. requirements per barrel of crude oil processed declined to a new low of 557,000 B.t.u. (see fig, 1).]

Jan 1, 1941

By Roswell W. Prouty

As part of a general plan for control and economic utilization of the waters of the Missouri River Basin as well as development of its inherent power resources, the Corps of Engineers of the United States Army has under construction a rolled earth dam near the site of old Fort Randall in South Dakota. The dam is in Charles Mix and Gregory Counties on the Missouri River at a point about 922 miles above its mouth. It is approximately 125 air-line miles southeast of Pierre and 55 miles southwest of Mitchell, S. Dak. The storage reservoir to be formed by the dam will extend upstream for 150 miles and, at maximum operating pool level, will cover an area of some 107,000 acres. It will have a storage capacity of 6.2 million acre feat.

Jun 1, 1949

By John P. Savage

This paper is one of a series being prepared by the United States Bureau of Mines on tunneling methods. The tunneling methods described are those used at the Ojuela unit of the Compania Minera de Penoles, S. A., the Mexican subsidiary of the American Metal Co., Ltd., of New York. The Ojuela unit is situated some 4 miles southeast of Mapimi, Durango. Mexico, the latter place being connected by a 15-mile narrow-gage railway with the standard gage railroad at Bermejillo, some 40 miles to the north of Torreon, the location of one of the company's smelters.

Jan 1, 1931

By A. F. Colombo, R. T. Sorensen, D. W. Frommer

The Bureau of Mines developed a flotation method for concentrating spiral tailing produced from pilot plant tests on the Champion mine ore fines . The feed material contained about 49 percent Fe and 15 percent SiO2 and was posed mostly of specular hematite , muscovite , and chlorite . Bench- scale , batch flotation research developed a reagent suite composed of tall oil - fatty acid , fuel oil , sulfuric acid , sodium fluoride , and sodium silicate for recovery of iron minerals in the froth product . Concentrate made with the reagent suite contained 87.3 percent of the iron and analyzed 65.6 percent Fe and 1.9 percent SiO2 . Continuous flotation tests were made with a nominal feed rate of 400 lb /hr , but without middling recirculation . Using nearly the same amount and complement of reagents as in the batch tests , three similar continuous tests gave concentrates averaging 63.9 percent Fe and 3.1 percent Sio while recovering about 86 percent of the iron .

Jan 1, 1964

By A. L. Engel

Production of chromite in California has been from many small, high-grade mines. The opening of the Purchase Depot at Grants Pass, Oreg., in 1951 has stimulated chromite mining in California, and a large number of properties are being reexamined as there is a possibility that some low-grade ores from many of these properties can be beneficiated to meet the purchasing schedule. The Bureau of Mines in its program of conservation is continuing ore-dressing tests on chromite ores to better evaluate their potential. This report is a compilation of preliminary concentration tests on samples from five different properties in California. The concentration tests were made on ores from the David mine, Butte County, the Seiad Creek mine, Siskiyou County, the High Plateau mine, Del Norte County, Bud's mine, Tuolumne County, and tailings from the Miller concentration plant in San Luis Obispo County, Calif., to determine the possibility of beneficiating these ores so that they will meet the specifications for the Government stockpile.

Jan 1, 1956

By James S. Browning

The Bureau of Mines conducted laboratory and small--scale continuous tests of weathered mica pegmatite ores from Hart County, Ga., to determine the technical feasibility of recovering commercial-grade mica concentrates by flotation. Two modifications of the Bureau-developed anionic-cationic method were used. In one method, sodium carbonate and calcium lignin sulfonate were used for pH control and quartz depression; this method yielded mica concentrates containing 98.5 percent mica with a recovery of 91.4 percent. In the other modification, lime and sodium silicate were used with the calcium lignin sulfonate; concentrates containing 98.9 percent mica with a recovery of 86 percent were obtained.

Jan 1, 1966

The Bureau of Mines, in an effort to improve resource conservation, mine planning and development, is currently investigating the loading behavior of pillars in multiple-seam developments. The simultaneous mining of two or more coalbeds may cause instability between room-and-pillar operations resulting in an interaction known as pillar load transfer. Although pillars may be adequately designed for single-seam mining, the development of a second seam may complicate loading conditions in both operations. If pillars are not adequately designed to contend with this load transfer, failure of the mine structure may result. To improve multiple-seam development and pillar design, the Bureau studied the loading characteristics of pillars in three separate multiple-seam operations. In all three cases, instrumented pillars recorded increasing pressure after development of the second seam. Increases in the average pillar pressure ranged from 7 to 110 pct over predicted overburden loads. An analysis of pillar loading before and after second-seam mining indicates that the ratio of overburden to innerburden thickness is a critical factor influencing load transfer. Based on this relationship, safety factors for case study pillars are calculated and alternative design considerations are discussed.

Jan 1, 1988

By Steven J. Schatzel

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers.

Jan 1, 2009

By H. E. Dresch

This report summarizes the work accomplished under Bureau of Mines contract H0188068. The contract required design and construction of a high voltage (7.5 KV) explosion proof cable connector for use on underground coal mine drag cables. A connector was constructed with elastomeric phase insulators that provide insulation shielding throughout the connector length. Connector housing was made of flame resist-ant cast poly urethane with no exposed metal components. Electrical and mechanical testing of the completed coupler resulted in satisfactorily meeting most of the design testing requirements.

Jan 1, 1981

By Daniel T. Rogers

The Bureau of Mines, in its alumina miniplant project to investigate alumina recovery from domestic, non bauxitic ores, has conducted research on the use of a hydrochloric acid leaching, gas sparging crystallization technology. An important element of this research is the efficient separation of undissolved, siliceous residue from AICI3 -bearing leach liquors by continuous, horizontal, countercurrent vacuum belt filtration. In an effort to calculate material balances quickly and to predict material balances based on different belt filtration configurations, the perfect-mixing-cells-in-series model (PMCS) for calculating material balances around belt filters was used. Because of the porous nature of the solids, the model produced erroneous material balances. Therefore a reliable model, the shrinking voids model, was developed postulating the presence of an unwashable voids liquor volume that decreases with decreasing liquor AICI3 concentration. This volume decrease postulation is equivalent to assuming that dilute liquors flow more freely, causing more voids liquor volume to become washable. Least-squares based computer programs are provided, which are useful not only in producing material balances from plant data but also in predicting balances for untested configurations using the same feed materials.

Jan 1, 1982

By A. L. Engel

This report is a compilation of results of preliminary concentration tests of seven manganese-ore samples. Six of the seven samples were submitted through the Mining Division, and 1 from Mexico was submitted by H. A. Doerner, formerly chief metallurgist, Region III. These investigations were made to assist development of mineral resources and particularly to aid economical exploitation of marginal or complex ores, from which strategic or critical minerals may be recovered.

Jan 1, 1953

By A. Gene Collins, Cynthia A. Pearson, Cathy J. Waters

The chemistry of selenium and tellurium is discussed , along with a method of preparing a synthetic oilfield brine , an oilfield brine sampling method , and methods for determining selenium and tellurium in complex oilfield brines . Selenium either can be reduced to the elemental form with sulfur dioxide and determined semiquantitatively by color comparison of the red amorphous form or can be converted to selenite and determined quantitatively by reacting it with 3,3 ' - diaminobenzidine and obtaining its spectral absorbance at 420 mu . Tellurium can be reduced to the elemental form with hypophosphorous acid , and the spectral absorbance of its red hydrosol can be measured at 400 mu . Less than 0.05 mg / 1 of selenium and 0.1 mg / 1 of tellurium can be determined by the described methods .

Jan 1, 1964

By Francis Church Linxoln

"This property was explored as part of a general investigation of zinc-prodccing areas of southwestern Wisconsin at a time when an effort was being made to increase the production metals important to the Nation's war program. This report describes the work that was done and presents the data obtained.ACKNOWLEDGEMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. It is the policy of the bureau to publish the facts developed by each exploratory protect as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, P., G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director. Special acknowledgment is due Professor G. H. Pett, of the Wisconsin Institute of Technology at Platteville, Wis., Jack Tracy, manager of the Mifflin Mining Co., and J. M VanMatre, representative of the Defense Property, for their assistance in the work. Acknowledgment is also due to A. F. Agnew and A. V. Heyl, geologists of the Federal Geological Survey, for furnishing geologic interpretations and lithologic studies of the drill-hole sections. All drilling was done under the immediate supervision of Francis C. Lincoln and M. Howard Berliner, project engineers, Edward P. Barrett, district engineer, Minneapolis, and E. D. Gardner, regional engineer, of the Bureau of Mines."

Sep 1, 1946

By M. H. Kline

The Scarlet mine, in Randolph County, N. C., was operated on a small scale at intervals from 1899 to 1915, but no records of the quantity of ore produced are available. J. I. Moore unwatered the mine in March 1948, and Bureau of Mines' engineers examined the underground workings. Several assays checked previous sampling of the mine and indicated a small but comparatively high-grade copper-zinc deposit. The high metal content of the veins and the possibility of developing additional reserves prompted the Bureau of-Mines to drill three holes, totaling 530 feet, at the deposit during March and April 1948. Drilling disclosed that the mineralized vein did not extend over 300 feet along the strike and is probably limited in depth to the contact with the granite mylonite.

Jan 1, 1949

By Halagowder Devaraj, Mostafa Sheykhnazari, Veer P. Bhavanandan

"A sensitive colorimetric assay for detecting mucins and glycoproteins rich in 0-glycosidically linked saccharides is reported. The method combines the susceptibility of N-acetylgalactosamine terminating 0-glyco idically linked saccharides to P-elimination with the Morgan-Elson reaction for N-acetylhexosamines with free reducing ends. All mucin and mucin-type glycoproteins but none of the serum-type glycoproteins tested resulted in characteristic color production. All mucins tested gave linear responses in the range 5 to 200 ""g and the assay was also adapted to the microscale involving the use of 96-well microtiter plates. The microassay in which the volumes of samples and reagents are scaled down 2.5-fold was particularly useful in monitoring of mucins, in the presence of other glycoconjugates, in large numbers of samples obtained during fractionation procedures. Cesium chloride, cesium bromide, potassium thiocyanate, and various detergents do not interfere with the colorimetric determination. Guanidine hydrochloride, cesium triftuoroacetate, and B-mercap- . toethanol decreased color by 30 to 45%; however, the interference was not serious to prevent the use of the method for detection of mucins in their presence. The use of the method for the specific detection of mucin during fractionation by gel filtration and density gradient centrifugation of cystic fibrosis sputum samples is demonstrated. Mucins are an important class of biomacromolecules whose structure-function relationship is poorly understood (1,2). The investigations of mucins are hampered by difficulties in purifying these very large size molecules which appear to avidly bind other components of the mucus (3,4). One of the problems during purification is the specific detection of mucins. For example, during the various purification steps, the fractions containing mucins are typically detected by assaying for neutral sugars (hexoses) (5,6), for sialic acids (7), or for periodate oxidizable saccharide units (8). However, these methods are not entirely satisfactory because neutral sugars, sialic acids, and periodate-oxidizable saccharides are also components of other glycoconjugates. In addition, the neutral sugar and sialic acid measurements are also subject to interference from high levels of proteins and nucleic acids."

Jan 1, 1990