Search Documents

By G. L. Oldright, Virgil Miller, F. K. Shelton, Keck. W. E., Horst Sieg

Potash is one of the principal foods and is necessary for the growth of most vegetables, grains, and fruits. For many years, this country depended entirely upon foreign sources for its supply of potassium compounds. However, during the last 15 years the domestic production of potash has gradually increased, as shown in table 1. 7/ Imports now supply only half of the American market. In 1936, the equivalent of 207,000 tons of K20 was imported, and 210,000 tons was produced domestically. In 1935, domestic consumption was approximately 420,000 tons of potash, a 57 percent increase over that for 1934 and surpassing previous peaks of 1928 and 1930.

Jun 1, 1937

By J. H. Tylczak

The Bureau of Mines studied the effect of alloy additions on abrasive wear of low-alloy steels. A dry-sand, rubber-wheel abrasion test appa-ratus using ASTM G65-Sl procedure B was used for the abrasive wear tests. Eighty-six material heat-treatment combinations were abrasion tested. Results of these tests were analyzed statistically using regression analysis to see if additions of Cr, Mn, Mo, Ni, Si, AI, Cu, and S were significant in affecting the abrasive wear rate of low-alloy steels. Regression analysis was also used to confirm hardness and C affect on the abrasive wear rate of these steels. It was found that for all the steels taken as a group, increased amounts of Mn significantly reduced the wear rate, while increased amounts of Mo and S1 increased the wear rate. Analysis also confirmed previous research done by others, that increasing hardness and amounts of C reduced the wear rate. For the hardened steels taken as a class, only increasing amounts of C and Mn reduced the wear rate, while increases in Si increased the wear rate. In the class of unhardened steels, increases in C, Mn, and S re-duced the wear rate, whereas increases in Mo increased the wear rate. The steels with the best resistance to wear were two hardened experimen-tal steels similar to AISI 1055 and AISI 107S.

Jan 1, 1986

By J. G. Kirby

The number of petroleum refineries in the United States continued to decline during 1954, and according to the Bureau of Mines annual survey there were 326 refineries with a total daily throughput capacity of 8,420,630 barrels, as of January 1, 1955. The increase in capacity for the year was 413,733 barrels daily, while the number of refineries declined 11. The capacity of the average refinery to process crude oil increased during 1954 from 23,759 barrels daily to 25,830. Breaking down the crude-oil capacity increase, by refining districts; 32 percent was installed at refin¬eries located in the Texas Gulf Coast district, 25 percent in the East Coast district, and 13 percent in both the Louisiana Gulf Coast and the California districts. The Appalachian No. 1, Texas Inland, and New Mexico refining districts reported declines in capacity during the year. Additional crude-oil capacity under construction, January 1, 1955, totaled 146,800 barrels daily. Included in this total are 4 new refineries, 1 each in California, Minnesota, New Mexico, and Washington. In addition to the' new facilities, equipment producing 1.49,550 barrels daily is being replaced.

Jan 1, 1955

By Ott F. Heizer

This paper describing the practice at the tungsten concentrator of the Nevada-Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on milling practices, methods, and costs in the United States. The ore, which contains about 1.10 per cent of scheelite (CaW04), is concentrated on tables and by means of a magnetic separator and roasters. A product containing 70.43 tungsten trioxide is shipped. The plant was designed for a capacity of 100 tons per 24 hours, but at present 142 tons of ore are milled per day. The author acknowledges the assistance of William O. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in preparing this paper.

Jan 1, 1930

By R. G. Travis

1. Reserve estimates have been made for eight coal beds in Monongalia County, W. Va., but only the Pittsburgh, Sewickley, and Upper Freeport beds are important at this time. The Pittsburgh, Sewickley, Waynesburg, and Upper Freeport beds contain the largest recoverable reserves. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 short tons per acre-foot of coal in place, are estimated at 3,526 million tons as of January 1, 1954. Of this total, 3,294 mil-lion tons is in beds 28 inches and more thick. Areas in each bed except the Pittsburgh were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Gary E. Sherman

The Bureau of Mines estimated the remaining lode gold endowment of eight mining districts in Alaska using historic production data. A log-arithmic model of cumulative tonnage of ore processed versus cumulative grade was applied to the following districts: Chichagof, Fairbanks, Homer, Hope-Seward, Juneau, Ketchikan, Prince William Sound, and Willow Creek. To assess the remaining endowment, a computerized production data base was compiled from Bureau records. These data were aggregated in 5-yr intervals for each district. Data were sorted in order of declining grade, and log cumulative grade was plotted against log cumulative tonnage. Linear regression was performed on the data for each district. The linear equation for each curve was used to predict remaining endowment at a limiting mining grade. Based on conservative extrapolation of the grade-tonnage curves, a substantial total endowment of 8,415,100 tr oz of gold remains in the eight districts. The districts with the greatest remaining endowment are the Juneau, Chichagof, Fairbanks, and Willow Creek Districts.

Jan 1, 1987

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment; including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that are recommended in this document, but all of the panic bars arc characteristically of the 'fire door" type that is frequently encountered on outside exit doors of many public, and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes arc added to the face equipment machinery for which they arty required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel at the various machine manufacturers and underground coal mines that we surveyed, discussions with G. I. Judy (our consultant), etc:

Jan 1, 1974

By C. E. Augustine, B. A. Landry, P. Nicholls

"Wien bituminous coal is burned in a hand-fired up-draft boiler used for heating purposes it has a decided tendency to produce smoke. A design of furnace and a method of firing and attendance that are satisfactory for fuels low in volatile matter, as anthracite or coke, are not necessarily Satisfactory for bituminous coals. It is therefore becoming common practice to use a special design of furnace for bituminous coals, in order to facilitate the combustion of the volatile matter and soot. This is done by (1) providing a larger combustion space to give more time for the combustion, (2) construction that will produce a better mixing of the gases and secondary air supplied over the fuel bed, or (3) keeping the gases at a higher temperature by preheating the secondary air, as may be done by surrounding them with refractory surfaces, or causing them to pass through a fuel bed of hot coke. A furnace may be built to use any or all of these methods of smoke prevention.In Bureau of Mines Technical Paper 303, Blizard5 and others give tests on a large heating boiler when burning coke, anthracite, and bituminous coal. Certair alternative furnace arrangements were used, but there was no material change in the furnace design for the various fuels. Since that time the manufacturer has made modifications in design to adapt it for use of bituminous coal, and additional tests have been made to determine how this change affected the production of smoke and the efficiency of the boiler."

Jun 1, 1929

By William S. Roberts

The Bureau of Mines has initiated a program to determine the availability of land for mineral exploration and development in Alaska. Researchers involved in this pro-gram are comparing land availability, based on ownership and government policies and regulations, to the distribution of known mineral deposits and terranes. This report on southeastern Alaska presents the findings of the first of six regional studies that will cover the State. The study consisted largely of data compilation and analysis using various mapping techniques. Summary land availability data are presented on copies of U.S. Geological Survey (USGS) quadrangles at a scale of 1:500,000. Five categories of land availability were identified: open to mineral exploration and development (approximately 9.4 million acres, or 38% of the 24.8-million-acre study area), open but with possible use restrictions (4.2 million acres, or 17%), selected (0.5 million acres, or 2%), patented (0.74 million acres, or 3%), and formally closed to mineral exploration and development (10 million acres, or 40%). Of the 1,187 known mineral deposits in the study area, approximately 38% are on land in the open category. Mineral terranes comprise approximately 6.7 million acres, or 27% of southeastern Alaska. Approximately 34% of these terranes are on open land.

Jan 1, 1985

By R. E. Morgan

Two sizes of Pennsylvania anthracite were gasified in the new-type Lurgi pressure generator at the Dorsten, Germany, works of the Steinkohlengas, A. G. These tests demonstrated that Chestnut-size anthracite and a Rice-Buckwheat mixture containing 27 and 19 percent ash, respectively, could be gasified satisfactorily at an elevated pressure in a fixed bed with oxygen and steam. These coals were especially prepared to approximate a rough-cleaned coal and a washed and screened product. The operating data obtained from the two tests and materials requirements are summarized. A wide range of reactant ratios could not be tested, nor could optimum operating conditions be determined, as the generator was being used throughout the testing program, employing normal operating practices, to produce gas for the gas grid; and the most economical coal, steam, and oxygen ratios may not have been used. Comparative costs are presented of the raw materials required for producing a high-B.t.u. gas, based on the operational data obtained from these tests and, to some extent, on data extrapolated from laboratory experimentation. A flowsheet of a proposed process for producing a high-B.t.u. gas by Lurgi gasification, followed by methanation, is also included.

Jan 1, 1958

This paper describes the sinking and lining of a 14 foot 6 inch finished diameter shaft down to and into the salt of a typical dome of the Gulf States region. The conditions and nature of the strata encountered divide the work into three distinct sections - that in (1) alluvial surface deposits, sunk through by open caisson methods, (2) water bearing rock, directly above the salt, and in (3) salt. ACKNOWLEDGMENT The writer wishes to acknowledge the cooperation of the sinking contractors, The Dravo Contracting Co. of Pittsburgh, Pa., through E. T. Gott, vice-president, in furnishing the data used in this paper.

Jan 1, 1932

By W. W. Agey

As a result of a field examination made during the Bureau of Mines intensive manganese program, three lots of ore were procured from the famous old Paymaster District, 7 miles from Midway Wells, Imperial County, Calif. This district is an old producer and shipped approximately 10,000 tons of 45-percent manganese ore during World War I. A 2-ton lot of ore was taken of a Bureau engineer from the exposure of a small fissure vein in conglomerate on the Turtle Group of claims; 1 mile east of the Pacific Coast Manganese Corp. claims. The vein material consisted of manganese oxides, calcite, and quartz in fairly coarse association.

Jan 1, 1949

By S. H. Ash

THE MAGNITUDE of the drainage problem of the anthracite industry in Pennsylvania's Western Middle field is realized when it is known that in 1951 nine pumping plants in this field pumped nearly 36 billion gallons of water to the surface. This is almost 68,000 gallons per minute pumped against an average hydrostatic head of 350 feet for that year alone. In 1948 over 20,000 gallons per minute was pumped by relay pumps against an average hydrostatic head of 265 feet. In addition to the water pumped to the surface, it is estimated that 15,000 gallons per minute overflows to the surface from underground pools in idle mines. The volume (second-feet) of water pumped and overflow water is almost 1;z times the, average mean flow of the Schuylkill River at Pottsville for the 8-year period 1944--51 (7, 13).4 Mahanov and Shamokin Creeks drain an area of 99 square miles in the Western Middle field, and all surface drainage in this area must traverse some part, of the coal measures before entering these streams. On the basis of 46.03 inches of rainfall (the weighted average of 6 recording stations for 1948), the runoff from the drainage area during that period was 51 billion gallons, approximately 1 times the volume of water pumped by all mine-pumping plants in the Western Middle field. In other words, because of the pervious strata overlying the mine workings, approximately two-thirds of the total runoff in the drainage, area becomes mine water tributary to the pumping plants.

Jan 1, 1953

By William H. King

The property of the Cupric Mines Co. is situated in the San Francisco mining district, Beaver County, Utah, 21 miles westerly from Milford (fig. 1), the rail and supply center for the area. Scheelite mineralization was not discovered until 1941, although the occurrence of lead and copper minerals had been known previously. S. VI. Hobbs, of the Federal Geological Survey, examined the Cupric property in November 1941 and prepared topographic and geologic maps of the area. This work was supplemented by additional investigations in January 1943 and March 1944 (fig. 2).

Jan 1, 1949

By Jon K. Ahlness

The Bureau of Mines conducted laboratory and field experiments to determine tne amount of permeability reduction in uranium sandstone after its exposure to different drilling fluids. Seven polymer and two bentonite fluids were laboratory-tested in their clean condition, and six polymer fluids were tested with simulated drill cuttings added. Sandstone cores cut from samples collected at an open pit uranium mine were the test medium. The clean fluid that resulted in the least permeability reduction was an hydroxyethyl cellulose polymer fluid. The greatest permeability reduction of the clean polymers came from a shale-inhibiting synthetic polymer. Six polymer fluids were tested with simu-lated drill cuttings added to represent field use. The least permeability reduction was obtained from a multipolymer blend fluid. A field experiment was performed to compare how two polymer fluids affect formation permeability when used for drilling in situ uranium leaching wells. For this test, the polymer fluid with the best laboratory results (multipolymer blend) was compared with a commonly used polymer fluid (guar gum) that gave poorer laboratory results. When fluid injection rates for the four wells drilled with the guar gum were compared with those for the four drilled with the multipolymer blend, no statistically significant difference was found.

Jan 1, 1984

By D. W. Butner

This Information Circular , one of a series published by the Bureau of Mines , reports on the methods and costs of mining and concentrating zinclead ore at the Highland Surprise mine in the Pine Creek area of the Coeur d'Alene region of Idaho . The mine is owned and operated by the Highland Surprise Consolidated Mining Co. , which supervises operations of the Nevada Stewart group of claims , which is adjacent on the northwest . These properties are at the extreme eastern end of a zone of fracturing that strikes northwest across the Pine Creek area . In fractures along this zone are the principal Pine Creek mines ; these are the Highland Surprise , Nevada Stewart , Sidney , Denver , V and Idaho , Liberal King , and Northern Light . Country rock at the Highland Surprise is argillite of the Prichard formation (Belt series ) . Fracturing has permitted the movement of mineral- izing agents that have replaced adjacent walls and crushed country rock with sulfides . Ore minerals are sphalerite and galena with accessory pyrite , chalcopyrite , pyrrhotite , and siderite . Three principal ore shoots were found on the Highland Surprise property . The Highland ore shoot was mined from outcrop to the 400 level . The Surprise ore body has been developed to a depth of 1,400 feet on the dip of the vein . The outcrop of the Surprise ore shoot was 150 feet long and 2 to 4 feet thick ; on the 1,150 ( lowest ) level , the ore shoot is 320 feet long and 10 to 17 feet thick , with good zinc content . Surprise ore shoot No. 2 occurs 250 feet west of No. 1 and has been mined from the 500 to the 1,000 level . From 353,000 tons of ore mined between 1910 and 1948 , the property has a recorded production of 256,000 ounces of silver , 7,500 tons of lead , 24,000 tons of zinc , and 412 tons of copper . Both shrinkage and cut and fill stoping methods are used at the Highland Surprise , but shrinkage is unsuitable for mining below the 700 level , because faulting has weakened the walls . Development of the Surprise ore , as well as exploration laterally and along the strike , is prosecuted steadily . A prospect heading is being pushed westward toward Nevada Stewart ground from the 700 level . The mill has a rated capacity of 275 tons per day and operates near capacity . Selective flotation makes zinc concentrate that is shipped to the Anaconda smelter and lead concentrate that is trucked to the Bunker Hill smelter at Kellogg .

Mar 1, 1950

By G. W. Jones, F. E. Scott, R. E. Kennedy

Methylene chloride , dichloromethane CH2C12 , a low - boiling and highly volatile organic chlorinated compound, is used extensively as a refrigerant in air conditioning installations , as an intermediate in organic synthesis , and as a solvent for cellulose acetate and other materials . As its vapors are not inflammable in air at ordinary temperatures , it can be used to advantage where it would be highly dangerous to use ordinarily inflammable solvents . The question has been raised as to its inflammable range in pure oxygen and in air enriched with oxygen . To find the answer to this question, tests were carried out with various mixtures of methylene chloride , oxygen, and nitrogen mixtures . It was found that methylene chloride has wide limits of inflammability in pure oxygen . Additional tests were then made to establish the complete range of inflammability of these gases . The methylene chloride employed in the tests was cbtained from the Eastman Kodak Co. It had a reported boiling range of 40.5 ° to 42.0 ° C. and a density of 1.322 at 20 ° C.

Oct 1, 1943

By L. C. IlsLey

A list of permissible mine equipment, tested and approved p or to July 1, 1934, was published in Bureau of Mines Information Circular 6813/. The present list4/ includes virtually all the electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lanes, electric hand and trip lamps, electric flood lamps, methane detectors, blasting units, storage-battery locomotives, tandem locomotives, mower trucks, and concrete mixers tested and approved by the Bureau to January 1, 1937. The system under which these devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the United States Bureau of Mines, to mark his equipment with a seal showing that it has been approved by the Bureau. These tests are designed to insure that equipments have the minimum requirements for safety in use. The only object of the bureau in making such tests and publishing lists of permissible equipment is to help decrease the hazards of mining.

Jan 1, 1937

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By C. J. Walker, J. S. Miller

This work was done in an attempt to find a simple solution to the problem of simultaneously changing terminal rate and terminal pressure under conditions of unsteady - state flow in porous media . Although the original aim was not realized , a method for encasing a sandstone core that would permit high - pressure ( 200 to 980 psi ) flow tests and the use of electronic equipment to measure pressures at points along the core during unsteady - state gas depletion was found to be feasible . The sandstone core used in this study was from the Bandera formation of Pennsylvanian age , Redfield , Kans . The core , cylindrical in shape with a 3.5 - inch diameter and 6- foot length , had a porosity of 15 percent and a permeability of 9 millidarcys .

Jan 1, 1963