Search Documents

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

By S. J. Schatzel, W. P. Diamond

Longwall mining alters the fluid-flow-related reservoir properties of the rocks overlying and underlying an extracted panel due to fracturing and relaxation of the strata. These mining-related disturbances create new pressure depletion zones and new flow paths for gas migration and may cause unexpected or uncontrolled migration of gas into the underground workplace. One common technique to control methane emissions in longwall mines is to drill vertical gob gas vent holes into each longwall panel to capture the methane within the overlying fractured strata before it enters the work environment. Thus, it is important to optimize the well parameters, e.g., the borehole diameter, and the length and position of the slotted casing interval relative to the fractured gas-bearing zones. This paper presents the development and results of a comprehensive, "dynamic," three-dimensional reservoir model of a typical multipanel Pittsburgh coalbed longwall mine. The alteration of permeability fields in and above the panels as a result of the mining- induced disturbances has been estimated from mechanical modeling of the overlying rock mass. Model calibration was performed through history matching the gas production from gob gas ventholes in the study area. Results presented in this paper include a simulation of gas flow patterns from the gas-bearing zones in the overlying strata to the mine environment, as well as the influence of completion practices on optimizing gas production from gob gas ventholes.

By A. S. Watts

The Bureau of Mines has been conducting an investigation of the feldspar resources of the New England and North Appalachian States with a view to greater efficiency and economy in their utilization. Such an investigation was deemed necessary, not only because of the continued and increasing consumption of these minerals, but especially because of the demand for better technical control of the raw materials that are used by the white-ware industries of the United States. Most manufacturers of white pottery wares have only a limited knowledge of the origin, mode of occurrence, and methods of mining and preparation of the materials that they use. Heretofore, owing to a belief that the supply of raw material was unlimited, the manufacturer had concerned himself chiefly with the solution of the problems of manufacture. Within the past few years, however, it has been found that difficulties arise in manufacture which can be traced beyond the manufacturing process and are believed to be due to a need of better control of the materials used. Furthermore, as competition becomes more severe, more attention must be paid to selection of materials in order to minimize consumption and also to avoid unnecessary expense for transportation of material. Doubtless the lack of interest as regards these details has arisen from the fact that in the past a considerable proportion of the whiteware ingredients has been imported and the manufacturer has been forced to rely on the samples submitted and the general uniformity of the source of supply to insure against variation of the material. An extra precaution arising from this lack of definite knowledge still prevails in the common practice of never depending on one source of supply for anyone ingredient. Often the products of three or more producers are blended so that if anyone shall vary without warning the variation arising from its use will not be sufficient to ruin the ware.

Jan 1, 1916

By C. W. Whitten

Iron ore deposits in south-central Missouri have emerged as a possible resource for the rare-earth elements. The Pea Ridge Iron Mine is one such deposit. Rare-earth minerals at the Pea Ridge Iron Mine are contained in breccia pipes consisting primarily of silicon oxides and feldspars. These pipes extend up through the magnetite ore body and appear to be alterations and replacement of earlier hematite. The mineralogy of these pipes is very complex and varied, which could complicate the concentration and extraction of the rare-earth minerals. This U.S. Bureau of Mines !eport represents a study by characterization of the mineral phases to assess the amenability and development of concentration and extraction techniques. Previous characterization of rare-earth minerals has been mainly by transmitted light microscopy. This method along with reflected light microscopy, scanning electron microscopy, and X-ray diffraction was used to identify and characterize the rare-earth and associated minerals. The minerals identified were the major ore minerals, magnetite and hematite; the rare-earth phosphates, monazite and xenotime; the rare-earth silicate, allanite; the minor associated minerals, cassiterite, pyrite, and apatite; and the gangue minerals, feldspar, quartz, and actinolite.

Jan 1, 1990

By Frank Chase, M. Terry Hoch, George Karabin, Joseph C. Zelanko, Christopher Mark

Pillar recovery continues to be a significant ground control hazard. During the past decade, 10 miners were killed during pillar extraction operations in southern West Virginia. Studies conducted during the past decade have identified a number of “risk factors” that can be used to evaluate pillar extraction plans: •Cut sequence •Final stump •Timber or Mobile Roof Supports •Roof bolting •Intersection span •Depth of cover •Roof quality •Age of workings For each of these factors, rock mechanics science suggests which alternative would be expected to be more risky. For example, numerical models were used to evaluate different cut sequences, and indicated that less roof convergence occurred with the outside lift method than with the Christmas tree in the particular environment simulated. For many of the risk factors, accident statistics confirm the science. One finding was that currently almost 70% of the retreat coal in southern WV is being mined with MRS. In contrast, timber supports were used in 70% of the past decade’s pillaring fatalities. This paper discusses each of the risk factors in turn, presents the relevant accident statistics, and shows how the risk factors can be combined to estimate the overall hazard. It also addresses the use of pillar design to minimize the risk of global stability hazards including squeezes, massive collapses, and bumps.

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By Rexford D. Singer

The purpose of this study was to evaluate the current literature on the use of calcium chloride and ligninsulfonates as dust suppressants with respect to potential adverse effects on health or the environment. Calcium chloride poses little internal hazard to man and animals, but toxicity to vegetation in and around the area of application should be expected. The effects, however, should be considerably less than those observed from using calcium chloride as a road deicer. Except for trout, ligninsulfonates seem to pose little direct systemic toxicity problems in aquatic organisms, animals and man or any problem with local vegetation. Because of a greater volume of information on its use and effects, calcium chloride is recommended over ligninsulfonates.

Jan 1, 1982

By M. M. Fine

Research on the solid-fuel reduction of Knob Lake iron or was conducted to upgrade lean and high-grade ores and recover metallized products suitable for ironmaking or steelmaking. The program included bench-scale tests plus a number of continuous campaigns in a 34-inch by 36-foot rotary kiln. In the laboratory, metallizations in excess of 90 percent were achieved by reduction of crushed ore with lignite at 950° C. Subsequent grinding (to minus 200 mesh) and wet magnetic separation yielded concentrates analyzing less than 3.0 percent SiO2 and more than 90 percent Fe. Virtually complete recovery of the iron occurred. During early continuous tests the crushed ore created a serious ringing in the kiln which was solved by balling the fines with bentonite. Unfortunately, at this temperature (950° C) the bentonite militates against the concentratability of the metallized product. For example, a run on direct-shipping ore produced concentrates of 89.5 percent Fe and 4.5 percent SiO2. At 500° C the adverse effect of bentonite disappeared and concentrates of 88.4 Fe and only 2.5 percent SiO2 resulted. However, with comparable feed r Los, the metallization dropped to 73 percent.

Jan 1, 1969

By Thomas Varley

During the past few years, since flotation has become the paramount treatment method for most all kinds of ores, the Bureau has gathered the data on consumption of reagents used in the flotation treatment. The first report was issued in 1916. A brief review of such reports snows the progress made in the art of flotation, and each year brings forth the development of new reagent a or combinations of reagents that seem sure to survive, but research and progress spell their defeat, if not by entire elimination, at least subjects them to considerable modification.

Jan 1, 1928

By Steve Signer, Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs, Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads, Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. 'These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

By M. Copeland

Phase relations of gadolinium alloyed, up to 40 weight-percent (wt pct), with AISI 304-type stainless steel were established. Body-and face-centered cubic iron-rich solid solution phases and several intermetallic gadolinium-containing compounds of variable composition that approximated the formulas Fe9Gd, Ni7Gd2, Ni3Gd, Fe2Gd, NiGd, and NiGd3 were identified. The intermetallic phases Fe9Gd and Ni7Gd2 were noted to melt at about 1,080° C at about 0 to 2 wt pct gadolinium. The melting temperature of Fe9Gd increased with increas-ing gadolinium content to a plateau at about 1,230°C and 30 wt pct gadolinium, and the melting point of Ni7Gd2 decreased to a plateau at 900° C and 30 wt pct gadolinium where Ni3Gd, NiGd, and Fe2Gd coexist. Body-centered cubic iron solid solution was stable from 1 to 2 wt pct gadolinium to higher contents, 30 wt pct gadolinium or possibly more, and face-centered cubic iron up to 12 wt pct gadolinium below 1,200° C. The stability of these phases above 1,200° C was not resolved except for the mel points. A limited number of fabrication variables as well as mechanical and corrosion properties of alloys containing up to 5 wt pct gadolinium were studied. Equilibrating and forming operations were best conducted at about 940° to 1,080° C. Some variability in the yield and tensile strengths of alloys was noted; however, there was a continual decrease in ductility and impact resistance with increasing gadolinium contents. The resistance of gadolinium alloys to corrosion in water at 354° C was about the same as stainless steel.

Jan 1, 1965

By G. L. Oldwright, F. K. Shelton, W. E. Keck

"INTRODUCTION Zinc must be of high grade to satisfy the present demand. Even when the amount of premium paid is small, the purer metal as the buyers' preference. The following specifications for spelter were taken from the American Society for Testing Materials for 1927, Part I, pane 524. (The specifications for 1930, p. 582, are tile same.)Another specification for zinc of a much higher grade than any of the above has been established lately by the same society. The committee on zinc die-casting (Proc. Am. Soc. Test. Mat., vol. 31, 1931, p. 263) reached the following, conclusions: I. ""That the purest of zinc is necessary to produce stable zinc-base die castings, and as a result requested specifications for zinc spelter .with total impurities not over 0.02 percent."" Their tests showed that the die castings made of the purest zinc had the least elongation and the greatest tensile strength, and exhibited the least changes with temperature.Still more far-reaching claims are made for the properties of zinc containing over 99.99 percent metal. Zinc foil, for instance, may someday be made as a common commercial product. It would seem likely that the demand for zinc of high grades rill continue and that even purer varieties may be desired. This demand fits in with the modern trend in manufacturing plants of reducing the number of variables to a minimum by using pure materials, and of controlling the processing of metals during their various stages of fabrication by mechanical means instead of by expert laborers."

Jun 1, 1933

By Edgar S. Rush

This study was conducted to make a limited evaluation of experimental and standard tractor dozer blades. A field test program was conducted in the southeastern part of Kansas on strip-mined areas where the spoil banks are parallel with rest-to-crest distances between 90 and 120 ft and maximum dozing distances usually less than 50 ft. This evaluation was a part of an overall joint Pittsburg and Midway Mining Company--U. S. Bureau of Mines (USBM) Specialized Reclamation Field Test Program primarily centered on the field t sting of experimental high-volume lateral relocation blades. The three blades evaluated were the 60-ft-wide angle (A) blade mounted on two 41B tractors. a 48-ft-wide A blade mounted on two D9H tractors, and a 13-ft-wide reclamation universal (Rec U) blade mounted on a D9H tractor. In addition to the experimental blades, three commercially available blades were tested: A 20-ft universal (U) blade mounted on two side-by-side (SxS) D9H tractors; a 20-ft U blade mounted on a 418 tractor; and a l2-ft straight (S) blade mounted on a D8H tractor. The dozer blade evaluations compared measured blade performance with soil and other site characteristics and with estimated earth-moving performance rates based on earthmoving methodology that accounts for the traction and speed of the tractor. The earthmoving methodology was also validated with data collected during this program.

Jan 1, 1978

By Christopher Mark

The first International Conference on Ground Control in Mining opened with the topic of pillar design. Two classic papers were presented, one by Bieniwski and the other by Wilson. Unfortunately, the two methods were so radically different from each other that it was nearly impossible to reconcile them. Adding to the confusion were the many other pillar strength formulas (such as the Salamon-Munro, the Holland-Gaddy, and the Obert-Duvall, just to name a few) that were also available. Little wonder that discussions of pillar design in those days often ended with anguished cries of “but which formula is the right one?” The past 25 years have seen substantial progress in the science of coal pillar design. Indeed, one testament to the improvement is the relative scarcity of papers on the topic at recent Conferences. Two factors have been largely responsible for the progress that has been made. The first has been the collection of large data bases of actual case histories of pillar performance in a variety of settings, from shallow room-and-pillar mines through deep cover longwalls. These have made possible the development of empirical design procedures that are closely linked to real world experience. The second important factor is the development of sophisticated computer models that can accurately simulate pillar behavior and roof/pillar/floor interactions. Together, these two lines of research have led to a new understanding of pillar mechanics that identifies three modes of pillar failure: • Sudden, massive collapse, accompanied by airblast, for slender pillars (width/height<4) • Squeezing, or slow, non-violent failure, for most room and pillar applications (4<w/h<10) • Entry failure or bumps for deep cover and longwall applications (w/h>10) It is particularly satisfying that the insights gained from numerical models broadly support those obtained from the empirical studies. While far less controversial than in the past, pillar design problems continue to arise. One recent example is pillar design for highwall mining. NIOSH has just released a software package, called ARMPS-HWM, which employs a number of modern pillar design concepts. Since highwall mining web pillars are long and slender, the greatest danger is that of a sudden collapse. ARMPS-HWM suggests two possible prevention strategies, one which

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By Gerald L. Finlinger

This Bureau of Mines publication reviews underground methane drainage programs being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By Kray Luxbacher, Mario Karfakis, Erik Westman, Peter Swanson

Three-dimensional velocity tomograms were generated to image the stress redistribution around an underground coal longwall panel to produce a better understanding of the mechanisms that lead to ground failure, especially rockbursts. Mining-induced microseismic events provided passive sources for the three-dimensional velocity tomography. Surface-mounted geophones monitored microseismic activity for 18 days. Eighteen tomograms were generated and high-velocity regions correlated with high abutment stresses predicted by numerical modeling. Additionally, the high-velocity regions were observed to redistribute as the longwall face retreated, indicating that velocity tomography may be an appropriate technology for monitoring stress redistribution in underground mines.

By K. K. Kelley

This work is a continuation of a program of study of the measurement and correlation of fundamental thermodynamic data inaugurated several years ago by the United States Bureau of Mines. Previous bulletins in this series were concerned with (1) The Entropies of Inorganic Substances (66),3 (2) High-Temperature Specific-Heat Equations for Inorganic Substances (67), (3) The Free Energies of Vaporization and Vapor Pressures of Inorganic Substances (68), (4) Metal Carbonates-Correlations and Applications of Thermodynamic Properties (71), (5) Heats of Fusion of Inorganic Substances (69), and (6) A Revision of the Entropies of Inorganic Substances-1935 (70). The present bulletin has as its primary purpose the correlation of the thermodynamic properties of elementary sulphur and its inorganic compounds and the presentation, after careful consideration of all available information, of a self-consistent system of thermodynamic relationships for these substances. It is believed that such a set of relationships, concerning substances of such great metallurgical importance as sulphur, sulphur oxides, hydrogen sulphide, metal sulphides, and metal sulphates, is of considerable value in indicating directions of possibly profitable experimental work and in clarifying subjects of technical interest upon which direct experimental information is difficult and expensive to obtain. It cannot be doubted that many problems of technical importance that at the outset appear almost hopelessly complex or obscure either may be solved, if enough information is available, or the specific lacking information clearly indicated by the adoption of the thermodynamic viewpoint. This has been demonstrated many times in the work of the Metallurgical Division, Pacific Experiment Station, Berkeley, Calif. Even when only crude basic information is available, a semiquantitative picture often may be developed by thermodynamic means in which general trends and approximate limits of a proposed process or modification of practice may be clearly portrayed and thus used as guides in further considerations and experimentation.

Jan 1, 1937

By N. A. C. Smith

The Bureau of Mines motor gasoline surveys have been conducted in January and July, during 1920 and 1921. The Bureau has obtained and analyzed samples of gasoline representative of that marketed in the larger cities. These surveys have indicated that the gasoline on the market during the winter months is more volatile than that sold during the summer months. Naturally, the motorist desires a more volatile gasoline in the cold winter months, as it affords greater ease in starting. The fourth semi-annual motor gasoline survey, conducted during the month of July, shows an interesting relation between the market price and the quality of motor gasoline. This is particularly evident if figures obtained today are compared with those of a year ago. At the time the Bureau of Mines conducted its summer survey of motor gasoline last year, the average tank wagon price of gasoline was 28.2 cents per gallon. This year it was 21.2 cents, a drop of practically 25%.

Jan 1, 1921

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944