Search Documents

By Jacob Miller, Phillip Mulligan

"Measuring the blast pressure associated with an explosion suspended above the ground (Free Air Burst)is a common research objective in Explosive Engineering. Theoretically, the shockwave from a Free Air Burst (FAB) configuration expands radially and the shockwave is assumed to have a smooth (uniform) shock front. The way in which the FAB explosive charge is suspended, packed, and the charge geometry can affect the shockwave expansion. These factors can generate a non-uniform shock front. As the scaled distance between the pressure sensor and the FAB increases, the shockwave expansion averagesnon-uniformities into a uniform shock front, at which point the FAB suspension system becomes less critical than when the scaled distance is “close-in” (Z <3)."

Jan 1, 2017

By Paul Worsey

A strong inverse relationship between rock face movement and stemming ejection is presented. Previously unpublished data from blast control plug research and development involving high speed video analysis, which was conducted between 1986 and 1988, is presented. Face and stemming ejection velocities were calculated for tests utilizing the same bench blasting configuration comprising; a 4 ft high bench in dolomite, 3 ft burden and single 1.75 in. holes loaded with 2 ft of small diameter cartridge emulsion. The singular difference between these tests was the stemming configuration. Varying lengths of stemming were used with the presence or absence of differing experimental configurations of blast control plug. The effectiveness of this plug has been published previously.

Jan 1, 1990

By Gregory P. Lorsbach

Significant information about any blast is contained within the seismic signal generated by the blast. In this study, standard digital signal processing techniques are utilized to extract source parameter information from a seismic signal recorded at distances commonly used in compliance monitoring. Specifically, digital seismic data was analyzed using the cross-correladon and autocorrelation functions for the purpose of determining delay timing. The initial results are interpreted to indicate that: 1) Individual delays can be identified analytically but not visually for short delay periods and large source to receiver distances, 2) Delay timing can be resolved to a few milliseconds, and 3) Results can be obtained from data collected at a minimal number of locations.

Jan 1, 1991

By Finn Ouchterlony, Gert Bjarnholt, Robert Holmberg

A system for contour blasting with a linear shape charge principle has been studied /10/. In one operation the charge creates two notches along the bore hole wall and breaks the rock mass. The built in notching capability makes it possible to reduce the specific charge and the bore hole pressure to 1/3 of what is used in conventional contour blasting and to ensure that cracks are initiated and propagated only at the notches and nowhere else. The notching capability of linear shape charges has been studied experimentally and the bore hole pressure calculated to aid in optimization of a charge for future field experiments in bore holes with a diameter of about 50 mm.

Jan 1, 1983

By R W. Givens

Comparison tests were performed on 6 emulsion concentrates, 3 microballoon sensitized emulsion concentrates, and 2 water gel concentrates from 8 different sources with ANFO used as a control standard. Variables measured include density, detonation, velocity, detonation pressure, calculated borehole pressure, viscosity, and lead cylinder deformation for blends of 15%, 30%, and 45% concentrate and AN/ANFO blends. Comparative results are presented for detonation velocity vs. deformation, and percentage of inherent air vs. deformation for these blends. It was hoped that these tests would serve as a tool to facilitate the comparison of different manufacturer's concentrates in AN/ANFO blends for equivalent performance characteristics and to help evaluate these products on an equal basis for bid solicitation purposes.

Jan 1, 1990

By Mark S. Stagg, David E. Siskind

Five major environmental effects of rock blasting are ground vibrations, airblast, flyrock, dust and fumes. What makes them "environmental" as opposed to occupational health and safety issues is that their impacts are felt off the mine, quarry or construction site. For some impacts, safe zones are defined through experience, flyrock being a good example. Flyrock at a mine can be 1) rock thrown beyond the blast area or expected hazard zone, 2) rock thrown beyond the permit area, or 3) rock thrown more than 1/2 the distance to the nearest non-mine structure (OSM rule for surface coal mines). Rock throw of less than the "flyrock" range is then a safety issue.

Jan 1, 1997

Hello, everyone. Way back in 1965, Devine and others at the US Bureau of Mines showed that a presplit fracture plane did not affect vibration levels transmitted across the plane (RI 6695).

Jan 1, 2010

By Robert Hopler

CHAPTER I. DEFINITIONS AND CLASSIFICATIONS. Definition of Explosives. SECTION 1. The term “Explosive” or “Explosives” whenever used in this ordinance, shall be held to mean and include any chemical compound or mechanical mixture that contains any oxidizing and combustible units, or other ingredients, in such proportions, quantities or packing that an ignition by fire, by friction, by concussion, by percussion or by detonator of any part of the compound or mixture may cause such a sudden generation of highly heated gases that the resultant gaseous pressures are capable of producing destructive effects on contiguous objects or of destroying life or limb, and includes all the articles specifically mentioned in Section 3 herein, and all other similar articles

Jan 1, 2013

By Mark S. Stagg, Norman S. Smith, Rolfe E. Otterness, Stephen Rholl

Blast design parameters were studied in an attempt to quantify their relationship to rock fragmentation. The Bureau of Mines conducted a series of 29 reduced-scale shots at the University of Missouri-Rolla's experimental mine with bench size from 40 to 80 inches. Design parameters varied were burden, spacing, explosive diameter and stemming-explosive length. The shots had 3 or 4 blastholes fired at delays of 1-4 ms per foot of burden, based on previous tests that showed hole interaction could improve fragmentation by 12 to 20 percent over single-hole shots or simultaneous firing. All rock, 2000 to 23,000 pounds per shot, was screened and weighed to determine the fragmentation size-weight distribution.

Jan 1, 1991

By C De La Cruz

The use of a thin-film piezoelectric stress gauge to determine the pressure profile in a detonating explosive has been demonstrated. These PVDF gauges have measured, in the borehole, the Chapman-Jouget pressure and the release adiabat of the detonation products for several explosives including ANFO and ANFO/emulsion mixtures. The technique can provide: (1) a direct measure of the blasting stimulus, (2) a sensitive QA tool for the blaster, and (3) a means to examine the magnitude and effects of preshock from adjacent bore holes. The PVDF pressure gauge is self powered, can measure pressure from a few bars to 400 kbars, has high time resolution (0.05 µsec), and is easy and economical to use.

Jan 1, 1997

By Thomas Barkley

Until the recent past, blasters have provided good to excellent results with tools and processes that have an inherent error. These errors can be found in drilling, explosives delivery quality and consistency, explosives loading consistency, actual explosives performance, and pyrotechnic detonator initiator accuracy. My experience and data from several decades in the industry show the error is often times 10% or higher larger in the dimensions that measure the performance of each of these tools and processes.

Jan 1, 2011

By S. S. Bud Jenkins

I went to an underground limestone mine recently to demonstrate the use of borehole liners. The liners were for horizontal holes in a normal “V” cut tunnel round. I hadn’t been in this mine for about 40 years. What a change. Way back they used cap and fuse and lit each fuse individually with a blowtorch. The face was about 40 feet wide and 14 to 16 feet high. They used ladders to get to the upper holes. The rounds were mostly slab rounds. I never saw this happen but had heard several times that the first holes were going off before the last holes were lit. I guess if this was true the use of slab rounds was a plus for safety. As far as I know they never had an accident but it was a scary procedure. There were a lot of scary procedures in the past and thankfully things have changed.

Jan 1, 2010

By Gabriel Gonzalez, Paulo Couceiro, Luis Manriquez, Alejandro Gutierrez, Juan Navarro

A high-stakes blasting campaign was successfully executed at a major open pit copper mine in northern Chile. This operation posed a significant technical challenge due to its immediate proximity to the tailings dam - a critical infrastructure whose structural integrity depends on strict control of blast-induced seismic vibrations. The geological complexity of the area, characterized by upper andesite interbedded with caliche (carbonate), further complicated the operation. This lithological composition, known for its high tenacity and cohesion, posed additional challenges for achieving effective fragmentation, necessitating a highly customized blast design and loading strategy. The campaign included four production blasts and one secondary blast, all executed under the constraint of not exceeding the Peak Ground Acceleration (PGA) threshold of 0.64g, as defined by the Maximum Credible Earthquake (MCE) scenario. To ensure compliance, geophones were strategically installed at three monitoring points (P1, P2, and P3) on the dam to capture real-time acceleration data. The use of specialized blast patterns, precise stemming control, and electronically sequenced detonations ensured that all recorded accelerations remained well below the critical threshold. A total of 496,163 tonnes of material were safely blasted, with 8,452 meters drilled and powder factors ranging from 419 to 594 g/ton. Therefore, this case study exemplifies operational excellence in controlled blasting, demonstrating the feasibility of safe mining near geotechnically sensitive zones through predictive modeling, rigorous QA/QC, and post-blast analysis.

Jan 26, 2026

By Robert Hopler

RBH Note: in 1913 black powder was still dominant as a coal-mining explosive, but permissible explosives were making some slight headway. For example, in 1902 there were only 11,300 pounds of permissibles used in coal mining, but in 1913 the quantity was 21,801,285 pounds. However, there were 187,551,653 pounds of black powder used that year. It took many years before the use of black powder ended in coal mining. From the picture of the miner reparing his explosives it’s hard to tell what he’s using, but the fact that a wooden Du Pont powder box is shown, he’s probably not using black powder. That doesn’t mean he’s using a permissible, either, since that was not yet a requirement. It’s interesting that the miners have open flame cap lamps, and the miner is actually smoking a pipe while preparing his explosives.

Jan 1, 2014

By Klaus G. Hinzen

Seismic observations offer the only possibility for remote sensing of physical processes like shock-front spreading, material crushing and ground movement. A better understanding of these processes will help to increase the economy of blasting. We developed a digital seismic monitoring system for research purposes. The system can simultaneously record up to 64 channels with a maximum sampling rate of 31 kHz per channel. A software package for rigorous analysis of blast induced seismic waves has been developed.

Jan 1, 1989

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By Jorge Cárdenas, Gustavo Huerta, Regina Rocha Oriundo, Miguel Angel Humpire, Johan Salas Flores

Currently a critical activity for slopes stability and safety in mining is pre-split blasting to reduce damage from trim blast. Most common explosive used are based on packaged explosives, with 1 ½ in diameter cartridges initiated by detonating cord. Traditional loading process requires a significant amount of trained personnel, which in our application context could take up to 20 blasters. When pre-split blast is scheduled, it usually reduces the availability of the blasters on the total loading services at site which are also demanded to have production blasting ready at same 12-hour shift daylight time.

Feb 6, 2023

By D E. Shaw, J B. Case, J Gusek

Explosive casting of overburden is defined as the use of explosives in blasting to move overburden to a spoil pile without rehandling. Studies of the economic feasibility of the method, and the formulation of a design hypothesis involving rock properties, and blasthole geometry are presented. These studies indicate that if technical feasibility can be demonstrated to increase surface coal production, considerable economic advantage would accrue to coal mine operators.

Jan 1, 1980

By Billy Rosseau, Mike Cammack, Richard O’Meara, Gustavo Azpilcueta

During the summer of 2014, the U.S. Army Corps of Engineers (USACE) sought proposals to vastly improve and expand the small boat harbor in Valdez, Alaska. It would be a multi-year project, and construction was scheduled to begin in the spring of 2015. One aspect of the project was the construction of a 3,100 feet (1000 m) rubble-mound breakwater to protect a mooring basin. An estimated 208,500 tons (190,000 t) of rock, ranging in size from 160 to 3500 lbs (73 – 1600 kg), were needed to build the breakwater. The Glacier Point Quarry was selected as the rock source due to its proximity to the project and the quality of the rock meeting all of the USACE rock standards.

Jan 1, 2017

By Ery Wardhana, Stefanus Jagad, Relinda Sanistya, Hasucita Tausi, Rido Situmorang

The blasting process is one of the most high-risk activities in mining operations. Shotfirers and blasting crews face hazards from slope failure, toxic gas and fumes, or unstable ground condition every day of the blast. But on the other hand, to ensure all of the holes are detonated, shotfirers are required to reenter the location to check. With advances in technology, nowadays the use of drone in mining is not something that is rarely seen. It has been used for mapping and slope-monitoring. This paper will discuss the application of drone for blasting process in a mining pit in East Kalimantan, Indonesia. By using drones, it is not only safety factor which can be improved but also operational efficiency and technical analysis. The duration it takes for post blasting process can be reduced because the drone can directly enter the location after blast. The technical analysis for the blast can also become more comprehensive, as the before-after photos and video documentation can be taken with wider view. It helps with fly rock calculation and fragmentation analysis too.

Feb 6, 2023