Search Documents

By Dale Preece, Joergen Pilz, Zavis Zavodni

An overland conveyor was constructed at a surface coal mine to reduce the truck haul distance and make the operation more efficient. An important element in this system is a truck dump facility to transfer coal from truck to conveyor. Mechanically stabilized earth retaining walls were employed to accommodate the coal processing equipment, including the crusher, in this facility. These retaining walls are close enough to the pits being mined that blasting induced vibrations must be considered in analyses of the wall structural stability.

Jan 1, 2010

By C. Breeds, K. Jeremiah, E. Jennings

Washington State has a well developed set of blasting regulations which have been promulgated by the Department of Labor using extensive stakeholder input, not only from citizens but also from manufacturers and representatives of IME, blasters in charge, blasting engineers, blasting companies, local and federal law enforcement agencies, fire officials, and local and state government representatives. WAC 296-52 therefore provides a foundation or platform for developing city ordinances for Washington State cities should a City wish to do so. On the other hand, Oregon’s code is based on OSHA 1926, Subdivision U, Blasting and the Use of Explosives which provides scant direction regarding the modern use of explosives. Reference is also made to ODOT Section 00335 - Blasting Methods and Protection of Excavation Backslopes. This paper examines two separate programs that have been developed by two Cities, one in Washington State and one in Oregon to further regulate blasting inside City limits and discusses why the lack of a regulatory foundation made one approach more difficult than the other. One of the authors was retained by the City of Kennewick, WA to develop their ordinance and has more recently followed and reacted to a pending ordinance for the City of Redmond, Oregon. The paper will compare and contrast the different approaches and comment on the reaction from both Blasters and the public. We also present a case study that involved blasting in an urban area of Oregon to prepare a foundation for a water tank. Controlled Blasting was carried out within 70-ft of residencies and within a community that had expressed reservations regarding blasting even though the work would make a significant contribution to the betterment of the community. Pre-construction surveys of residencies located in a large area surrounding the site were performed and a well-planned blasting program was carried out. Residencies were subject to vibration levels that were monitored using six seismographs that surrounded the site and these units measured vibration levels that were significantly lower than allowed by statute. There were complaints triggered by individuals reactions to blast vibrations which validated commonly held models of human perception but no damage was caused by the Blasting.

Jan 1, 2024

By P J. Dailey, S L. Burchell, R F. Chiappetta

High-speed motion picture photography and its application to the mining, quarry, construction, and explosive industries has proven to be a valuable diagnostic tool. The techniques developed allow one to evaluate blasting performance, compare explosive efficiencies in relation to burden velocity, and estimate optimum delay times to provide adequate forward relief.

Jan 1, 1983

By Dworzak, Andrzej Biessikirski, Jozef Pyra

During the detonation process 20-30% of the energy is being consumed only on the quarrying pro-cess. The remaining amount of the energy generates harmful effects such as: shock wave, acoustic wave, fly rocks and ground vibrations. The ground vibrations effect is the most dangerous especially to structures which are situated nearby an open pit mine.

Jan 1, 2015

By R. Franfield, W. J. Birch, L. Bermingham

Previous researchers have put forward two different theories as to the origin of air overpressure from quarry blasting. In 1980, Siskind et al postulated that the initial face movement gave rise to the displacement of air and that this resulted in the air overpressure pulse. However in 1990 McKenzie et al carried out research that indicated that the air overpressure pulse came into being as consequence of the shock wave created by the detention of the explosive charge in a blast hole, rapidly propagating through the rock and then impacting on the quarry face.

Jan 1, 2013

By Hideaki Kitajima, Daisuke Fukuda, Kazuma Moriya, Katsuya Sasaki, Katsuhiko Kaneko

The purpose of this research is to analyze the fracture process and achieve design optimization of a splitting method for concrete and rocks termed the electric discharge impulse crushing method (EDICM). The EDICM utilizes the cartridges being set in boreholes in the splitting target. The cartridge has a thin metal wire and is filled with nitromethane. By applying the electric discharge to the wire in the cartridge, plasma is caused leading to the vaporization of the wire. Then the deflagration of the nitromethane commences, which generates borehole pressure for splitting the target. Although the required splitting time is roughly several hundred micro-seconds and much slower than ordinary blasting, the fracturing still completes in quite short time and understanding the fracture process of opaque and brittle materials such as rock and concrete in this time scale is of academic importance.

Jan 1, 2011

Existing geological structures such as faults or shear zones can greatly influence the interpretations of amplitude or energy attenuations of measured blasting vibrations along both affected and unaffected orientations. Mineralisation in conjunction with large faults or shears is commonplace in the geology of steeply dipping metalliferous deposits, such as those found in the goldfields of Western Australia. Better understanding of the influence of faults or shear zones on blast-induced seismic waves can lead to more effective blast vibration monitoring programs and interpretation of the results measured along affected orientations.

Jan 1, 2011

By D Maxwell Ellett

This report presents an evaluation of knowledge concerning a process used in predicting ground motion resulting from large scale conventional explosive detonations, The shots were set off in Arizona in connection with copper ore recovery activities.

Jan 1, 1976

By Leslie C. Taylor, Scott A. Yamada, William L. Fourney

Previous studies have shown that the pressure load on a target by a buried explosive charge is not smoothly distributed. The effort reported here was undertaken to explore the mechanisms believed to cause this uneven pressure distribution: jets from the surface originating in instabilities caused by the explosive shockwave interacting with surface irregularities. Small-scale tests using conical, hemispherical, and cylindrical indentations in the sand surface above a buried charge were conducted to identify trends in the velocity and form of the resulting jets. In these tests, the most important factor affecting the resulting jets was the distance between the bottom of the indentation and the top of the charge. Cylindrical indentations resulted in higher jet velocities than those from comparable hemispherical and conical indentations.

Jan 1, 2012

By P D. Katsabanis, S Kim

A number of small scale fragmentation tests have been conducted to analyze the effects of blasting effort on the grindability of granite, granodiorite, limestone and iron ore. Powder factors were modified, post-blast fragments were screened and drop weight tests were conducted on fragments of different sizes to deliver a variety of specific impact energies. The fragmentation from the drop weight tests has been analyzed to examine the effect of impact energy and powder factor on size reduction. A consistent effect of blasting on the various fractions of the fragmentation distribution has been obtained for all rocks used. The effect of powder factor on the impact fracturing of the rocks has been expressed in a convenient relationship between progeny size, impact energy and powder factor used in obtaining the primary fragmentation. It is clear that explosives consumption affects downstream size reduction; depending on the rock, the effect can be substantial at coarser final sizes but very small in the case of grinding to small final sizes. Differences from the expected trend can be attributed to changes in blast design. As an example, the effect of in-hole collision of detonation waves is analyzed.

Jan 1, 2011

By P. E. Hoffman, Joshua Ph. D.

The Institute of Makers of Explosives (IME) led a post-detonation debris collection project in conjunction with a large AN railcar detonation conducted by the Department of Homeland SecurityTransportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in the IMESAFR (Institute of Makers of Explosives Safety Analysis for Risk) Quantitative Risk Assessment (QRA) tool. The test also provided valuable data about AN detonation characteristics when it is driven to detonation. The test took place at the Utah Dugway Proving Grounds (DPG) on April 27, 2018 and the debris collection was conducted the following two weeks with an average of 20 persons per day and an approximate total of 1,400 manhours. This paper details the collection efforts, challenges, and lessons learned. It also presents some of the initial findings relating to the debris distribution.

Jan 1, 2019

By Miquel Lamadrid, Changshow Sun, Chris Johnson

To reduce blasting overbreak and improve stope stability, several new blast designs were proposed for current and future stopes. Based on the analysis of the powder factor, and the extent of damage zone, the appropriate new blast design was selected. Excellent results were achieved from the new blast design. Comparing the new blast design with the old one, the largest of the overbreaks decreased more tan two times and average overbreak reduced more than two times. The new blast design is currently applied in all mining zones in Leeville underground mine.

Jan 1, 2008

By A K. Raina, P B. Chourdhury

Flyrock is the unwanted throw of rock fragments to excessive distances in opencast blasting. The incidence is relative in nature incorporating the distance of objects of concern like structures within and outside the mine, equipment within the mine & near the blast and persons within and off the mine. Several attempts to predict and defi ne fl yrock made worldwide could not address the problem since the phenomenon is not a regular feature in blasting. This probabilistic nature of fl yrock allows for risk calculation. CIMFR, India developed a Factor of Safety based risk criterion (10, 14) for evaluation of throw/ fl yrock in opencast mines that incorporates all the above in terms of distance and allowable limit of throw – which in turn determines the risk. The criterion provides the blaster a tool for mathematical evaluation of fl yrock risk in terms of a Factor of Safety and threat ratio (defi ned for the 1st time), thereby enhancing confidence when blasting. The method is easy to use and has been applied to several mines in India and the results are signifi cant. This paper details the evolution of the concept and its application in three limestone mines of India and the results obtained. The application of the method for defi ning a fl exible danger zone is also discussed.

Jan 1, 2008

By L. M. Lopez, J. A. Sanchidrian

This work investigates the performance of some of the measurement techniques used in vibrations from blasting monitoring. Two tri-axial geophones with cases of different size, shape and mass were tested in a shaker table. The geophone cases were mounted in three different ways on a granite slab fixed to the plate of the shaker: freely placed, sandbagged, and anchored. A known horizontal periodic motion of constant amplitude, and frequency from 16 to 200 Hz, was applied to the slab. Two amplitude levels of 5 and 20 mm/s (0.2 and 0.79 in/s) were applied when the sensors were sandbagged or anchored and only 5 mm/s when no holding force was applied. The transmissibility of vibrations from the rock to the longitudinal geophone as function of the frequency (i.e. ratio of response of the geophone to the slab motion) has been obtained for each measuring condition tested. The transmissibility is considered a composition of the transmissibility of the rock-to-sensor coupling and the transmissibility of the sensor’s mechanics and electronics. The transmissibility of the coupling is obtained normalizing the total transmissibility with the transmissibility of the seismographs, obtained by a suitable test to which a coupling transmissibility of 1 is assigned. Geophone-to-rock coupling is a resonant phenomenon that may alter the amplitude of the measured waveforms by a factor of 1.2 to less than 0.6. The most accurate and precise measurements are obtained with geophones anchored to rock. On the contrary, freely placed or sandbagged sensors are non-predictable planting conditions that lead to high amplification or damping in most of the frequency band analyzed. It is also shown that existing acceleration criteria to select coupling methods do not necessary lead to good quality (accurate and precise) vibration data.

Jan 1, 2014

By Eduardo Lozano, Vilem Petr

This study demonstrates the ability of high-order, shock-capturing methods to simulate detonation wave propagation in right circular cylinders of non-ideal explosives. 2-D axisymmetric, reactive Euler equations were solved for the detonation of the highly non-ideal explosive ammonium nitrate-fuel oil (ANFO) using a simple pressure-dependent rate law and perfect gas equation of state. The fractional step method was applied to the convection and reaction operators using a 2nd-order Strang splitting. The flow solver consisted of a finite difference scheme where the flux is reconstructed by a modified fifth-order weighted essentially non-oscillatory (WENO5-Z) with local characteristic decomposition and local Lax-Friedrichs (LLF) flux splitting. Time integration was performed by a third order total variation diminishing (TVD) Runge-Kutta time discretization method, also known as the strong stability preserving (SSP) method

Jan 1, 2019

By Carlos Pañura, Michael Geldres, Alejandro Rojas

In this current era of production in large volumes of surface mining, which demands the realization of large-scale blasting, the mining industry must deal with the impact of the vibrations generated by the detonations that are carried out daily in the mines. In this context, the need arises to minimize and control the impact produced by vibrations by determining the interference times of each generated vibration waveform. The vibration waves are produced by the detonation of the explosive charges of each blasthole, analyzing the vibration waves produced by each blasthole, allow us to determine the optimal time between the detonation of each blasthole to reduce the vibrations of the production shot. Once the optimal time is found, it is possible also, to predict the vibration of the production shot (considering times and sequences) using predictive models. The waveform recorded includes information regarding the particle velocity and the dominant frequencies of the vibration. To determine the time between holes, a graph was constructed with the values of the vector Sum VPP (m / s) vs Time between blastholes (s), once the time between blastholes “t” was found, the simulation of the output sequences continued in such a way that, by adding the single waves generated by the blasthole, it gave us a record of vibrations with the lowest level of vibrations.

By Nolan Eckroade

The demand for blast optimization within the quarrying industry calls for more effective, faster and safer methods of quantification of blast performance. Drones provide the ability to safely and quickly capture high resolution imagery of a muckpile for use in fragmentation photo analysis. Oversize material within a muckpile is an expensive and universal problem affecting quarries, especially in situations where cap rock is present. Although the amount of oversize material in a blast is a key indicator of blast performance, it is difficult, hazardous and slow to measure across an entire muckpile using traditional methods. By piloting a drone using an automated flight plan with set amount of overlap across images, the images can be processed into a single, high resolution orthomosaic image for use in fragmentation photo analysis software.

Jan 1, 2018

By Larry Schneider

In 1998, the Blast Vibration and Seismograph Section of the International Society of Explosives Engineers formed a working group to collect and compile a list of regulations limiting ground vibrations from blasting. The goal was to locate those countries, states, provinces, and cities that have such regulations, identify which governmental body enforces them, and determine what limits on ground vibrations are imposed upon the blasting operations. In the course of this study, data was collected from over 60 jurisdictions where peak particle velocity restrictions range from non-existent to very stringent. Some of the regulations were found to be based upon standards grounded in good science, while others possess little or no technical justification. This presentation will summarize the findings of the subcommittee, focusing primarily on what the limits are, which type of blasting operations must adhere to them, and to what structures they apply. The degree to which these regulations are based upon valid scientific and engineering research will be discussed. A listing of specific locations having such regulations and information about those regulations will be provide

Jan 1, 2000

By James G. Stuart, Tassilo N. Baur

We will discuss the kind of procedure that we use to predict the no-fire (for safety) and all-fire (for reliability) current levels for any given type electric detonator. The basic idea is to expose several detonators to different levels of electric current, so we can estimate the probability of firing as a function of current. We call this a statistical firing test. But what about the uncertainty in measuring the current? Suppose we are not quite sure what stimulus level we apply? This is the question that we will consider here. This relates to both safety and reliability. Surprisingly enough, we will find that some uncertainty in measuring the levels during our statistical firing test improves our long-term safety and reliability

Jan 1, 2019

By L C. Taylor

Very small scale testing has been shown to be able to predict quite accurately, in many situations, the results of full scale testing. Small scale tests are more cost efficient, easily observed, and easily instrumented than full scale tests. Over the past 10 years small scale testing in the Dynamic Effects Laboratory at the University of Maryland has been used to successfully study the response of structures and soils to explosive detonation. Small scale testing has been successfully used to predict full scale results in underwater cratering and channeling, the loading (both pressures and impulse) on vehicles due to the detonation of buried charges, the positive effects of bottom shaping for military vehicles to reduce this loading, and the movement of obstacles underwater by explosive charges.

Jan 1, 2012