Search Documents

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By M. Saghaeian, R. Hejazi, L. Hosseini

The specific surface area (Blain value) of iron ore concentrate entering the pelletizing plant is one of the characteristics most effective on the overall performance of the plant such as producing harder pellets, decreasing additives consumption, and decreasing energy consumption. Therefore, preparing the feed entering pelletizing plant is required. The iron concentrate entering Ardakan pelletizing plant located in Yazd province, Iran bears relatively low Blain value (approx. 1600 cm2/g) which necessitates one stage of regrinding so as to increase the Blain value to more than 1800 cm2/g. Studies were conducted and results showed that HPGR is the best regrinding equipment for increasing specific surface area. Conducting pilot plant tests on the concentrate sample revealed that specific throughput is 181 to 263 ts/hm3 and specific energy consumption is 1.6kWh to 2.2 kWh. Pilot tests also showed that one stage of grinding results in 407 cm2/g to 553 cm2/g increase in specific surface area. Based on these results, diameter of rolls, length of rolls, power consumption and grinding force were calculated to be 1.3 m, 0.9 m, 1276 kW and 13800 kN, respectively. Therefore, an HPGR with a roll diameter of 1.52 m, roll width of 1.1 m, power of 1660 kWh and a capacity of 500 t/h has been selected and implemented in Ardakan pelletizing plant. Industrial performance of HPGR and its effects on the plant study results show that limestone and bentonite consumption has reduced about 60% and 30%, respectively. Total Fe of the final pellet has increased from 65.5-65.7% to 66.2%. Cold compressive strength (CCS) and porosity of final pellets are approximately 292 kg/pl and 20.4, which are in the acceptable range.

Jan 1, 2014

By X. H. Li, F. Xie, Q. Zhang, Z. H. Shen, S. Mao

"There is abundant rare-earth element(REE) in our country, but it is very fragmented in the earth's crust, and it is very difficult to mining or mining cost is extremely high. There are few of industrial value rare-earth deposits. There is a lot of concomitant rare-earth deposits, and the comprehensive utilization value is high. There is very rich carlin-type gold resource, associated with a certain amount of REE in the southwest of Guizhou province. In order toutilize comprehensively the resources, this paper conducts the study on the occurrence characteristics of REE in the ore. By the chemical analysis, the gold grade is 3.35g/t, the organic carbon 0.81%, the total REE 0.022%, which is a high carbon fine disseminated gold ore. By the optical microscope and XRD analysis, the major minerals are quartz, pyrite, calcite, limonite, arsenopyrite, mica, kaolinite, clay minerals, etc. In addition, there is a large amount of carbonaceous materials, such as organic carbon, graphite, which is harmful on leaching of gold. By the scanning electron microscopy analysis, there are thorium, lanthanum and neodymium, ytterbium, persimmon and other REE in the ore. Gravity separation shows that REE could be enriched to lighter material mainly, which indicates that REE disseminate closely with lighter materials.INTRODUCTION Carlin-type gold ore is important gold resource in the world, which are mainly distributed in Nevada and its vicinity, as well as the two Golden Triangle of Yunnan, Guizhou, Guangxi and Sichuan, Shanxi, Gansu province in China(Su W.C. et al.,2009; Xia G.X.,1996).Guizhou carlin-type gold ore is the second largest gold resource in the world(Muntean J L et al.,2011), distributing along the southwestern margin of the Yangtze plate, mainly mineralizing in the neopaleozoic-early mesozoic(Xie Z J et al.,2017). Many large gold deposits have been found in southwest in Guizhou in twentieth century, such as Zimuyou,Getang, Lannigou, Shuiyindong and Laowanchang gold deposit, and so on, and the gold reserves reach over 100 tons(Xia Y. et al.,2009).There is a certain amount of rare-earth resource in the carlin-type gold ore in the southwest in Guizhou province, and the current researches might mainly focus on characteristics of REE from the angle of geological mineralization(AnanyevY.,2015), not from the angle of separation and enrichment."

Jan 1, 2018

By E. V. Konoplev

Russia is one of the largest manufacturers of potash fertilizers in the world. Processing of potash ores basically is carried out by a flotation way. Potash ores of the Verhnekamsky potash deposit contain sylvite (KCl), halite (NaCl) and water insoluble impurity (up to 8 %), presented silicate- carbonate minerals, easily slimed by ore crushing in rod mills. Ore of some deposit sites, developed by ?Uralkali? Co, contains a significant amount of a carnal-lite (KCl.MgCl2.6H2O). Work practice of flotation potash plants has shown, that increase of car-nallite content in ore leads to increase magnesium ion content in a circulated plant brine (saturated salt solution of potassium and sodium chlorides-sylvite brine) and to deterioration of indicators of ore processing. In the Paper we present results of researches of floatability of various size sylvite and influences silicate-carbonate slimes on sylvite flotation in brines with the various magnesium chloride content. It is established, that with increase magnesium chloride content in the brine mainly decreases the flotation of coarse sylvite and amplifies adverse effect of silicate-carbonate slimes on sylvite flotation. In this connection deterioration of potash ore flotation is caused not only decrease sylvite floatability but also strengthening adverse action of water insoluble impurity on potash flotation. It is shown that the application of frothing agents, which render the stronger dispersive action on the colloidal-micellar structures of amine in the salt solution increases the absorption of collector on the sylvite and improves the flotation of sylvite into magnesium the containing salt solutions. The application of an organic depressor to the greatest degree of decreasing the absorption amine on the slimes and to the smallest degree possessing anionic properties proves to be most effective with the flotation carnallite of the containing potassium ores. It is offered the application the frother on a basis of glycol ethers and organic depressor on a basis of urea-formaldehyde resin. Results of industrial tests developed reagent modes for flotation treatment of ores with the raised carnallite content (to 6 %) on ?Uralkali? Co plant have shown that their application has allowed to receive equivalent indicators potash flotations at change of magnesium chloride content in the brine from 0.7 % up to 2.4 % .

Jan 1, 2014

Nowadays, the more successful plants are those who have adopted effective and efficient strategies to optimise their plant operation. As the ?heart of the plant? could be viewed as the mil-ling/grinding area, one of the key steps in plant optimisation is, therefore, ensuring the mill is operating properly. In the past, when primary, secondary and tertiary crushers fed material directly to large ball mills, the energy efficiency of the concentrator was determined for the most part by the ball mill operation, whereas now the energy efficiency of a plant often rests largely on the semiau-togenous grinding (SAG) mill operation. As a result, mines have shifted their emphasis in optimization from ball mills to SAG mills. The grinding mill?s energy efficiency essentially depends on ore characteristics and the discharge rate of broken particles, which in turn depends on how efficiently the discharge pump (grate and pulp lifters) operates. The essential function of pulp lifter being to transport the broken material and slurry out of the mill, its design optimization therefore affects the discharge capacity (or mill throughput) of AG and SAG grinding mills. This paper will discuss how the optimised design of the pulp lifter/ discharger has helped to eliminate material transport issues such as flow-back and carry-over of slurry and pebbles to in-crease the energy efficiency of SAG mill using the actual operational data.

Jan 1, 2014

By M. R. Hosseini

Among all gravity concentration methods, Shaking-table is the most effective one from the metallurgical point of view. In this study, Shaking-table was used for concentrating a manganese ore sample from Ghasem Abad area in Kerman, Iran. Experiments were designed by using L8Taguchi design with five variables and each variable in two levels. The influence of each variable and their interactions on the operation of the device was studied. The variables under investigation were: table slope, table frequency, water flowrate, feed rate, and particle size. The manganese concentrate grade and recovery were used as response variables. It was shown that water flowrate, table slope, feed rate, and particle size are the significant variable on concentrate grade; while, all the variables influence manganese recovery.

Jan 1, 2014

By E. Hulthén

Cone crushers are used in the mineral, mining, and aggregate industry for fragmentation of rock materials. Control systems for cone crusher settings are widely used to compensate for wear and to protect the machines. The eccentric speed in a cone crusher affects the number of compressions the material is exposed to and thus the particle size distribution of the product. Eccentric speed also affects crusher capacity. However, the speed of the crusher is mostly fixed, because speed changes must be made by shifting pulleys, a process which is quite time-consuming. By applying a frequency converter, which has decreased in cost during recent years, it has become possible to adjust the speed continuously. By also applying mass-flow sensors to the process, the crusher can be run optimally to yield the most sellable products in a given moment. Existing systems normally only protect the machine. The sensors can be mass-flow meters, e.g., conveyor-belt scales. To analyze data from the process and calculate the appropriate value for the speed, an algorithm has been developed. The developed algorithm was tested and evolved at a crushing plant for aggregates that produces around 350 kton a year. The algorithm was implemented in a computer that could communicate with the frequency controller, retrieve data from four mass-flow meters, and also interact with the opera-tor. The computer was reachable over the Internet for the researchers at Chalmers and the algorithm was tuned and improved on-line. The result is a crushing stage that consistently and maximally produces the most desirable product. The performance (yield of required products) increased by 4%. As a bonus, the lifetime of the mantles increased 27% on the evaluated crusher.

Jan 1, 2014

By X. Xu

This paper presents the research on comprehensive recovery of copper, gold, silver and iron from tailings from high-intensity magnetic separation in Tonglushan Mine. By comparison of experimental results of three flowsheets?regrinding of tailings-conventional sulphidizing flotation, water heating enhanced sulphidizing flotation and acid leaching-sulphidizing precipitation flotation, it is concluded that regrinding of tailings-conventional sulphidizing flotation flowsheet has the best economical and technical performance and practicability. Regrinding and using the mixture of sodium hydroxamate and sodium xanthate are two of the notable technical characteristics of this best flowsheet. The system for comprehensive recovery of tailings has been put into production. It not only can recover the valuable minerals from tailings in Tonglushan Mine, but also can reduce the environmental pollution, resulting great economic and social benefit.

Jan 1, 2014

By Abhilash

Different methods of utilizing refractory bauxite and disposing red mud are practiced throughout the world, but none of them are known to be environmentally innocuous due to the complexity and /or high cost, and none has been found to be feasible on an industrial scale. Under these conditions, the use of bioleaching process seems promising. The present study emphasizes on the isolation of native extremophiles from the source Indian bauxite and red mud, with their detailed cellular and physio-chemical, and biochemical characterization. These organisms were tested for their ability to thrive in physically or geochemically extreme conditions. The gram positive capsule rich mesophiles and thermophiles were tested for removal of gangue minerals from the bauxite and red mud samples. Keywords: refractory bauxite, red mud, extremophiles, bio-beneficiation, gangue

Sep 1, 2012

By H. C. E. Regidor, M. G. Mena, H. D. Mendoza

Cyanidation leaching has always been the most widely used method of extraction of gold in the world. Its low cost and high selectivity has made it the prevalent choice for mining companies, and even for the small scale miners. The use of cyanidation in small scale mining has been an issue for the longest time, mainly due to the operation’s lack of safety measures, health care or environmental protection regulations. In pursuit of more environmentally friendly methods of extraction of gold, several alternative extraction processes have been explored, one of which is chlorination. The chlorination process is advantageous when recovering refractory gold locked in sulfides, as it simultaneously oxidizes the surrounding sulfides as well as dissolve any gold exposed to the lixiviant. This research was conducted to study and develop a safer alternative way of extraction of gold from small scale mining operations, without compromising the recovery of gold. In this study, a variation of the chlorination process has been employed for a refractory flotation concentrate wherein the majority of the gold is locked in sulfides. Hypochlorite-bearing reagents were used as the leaching reagents, and the method developed was a 2-stage leaching process in differing pH conditions. The solution pH and Eh was monitored all throughout the runs, and aliquot samples were taken at time intervals for analysis. SEM-EDS imaging was used to determine the mode of oxidation of the chlorination process, and the image obtained showed that the oxidized layer followed the shape of the particle, suggesting a diffusion controlled process. XRD analysis of the sample before and halfway through leaching further confirmed the oxidation of the sulfides. The amount of gold dissolved in the aqueous solution and in the solid residue were used as the basis for the determination of the recovery of gold. An average gold recovery of up to 84.38% was obtained using the developed method in just 7 hours of leaching. This method was then employed for a pilot-plant scale test and a gold recovery of 79.2% was obtained.

Jan 1, 2018

By A. S. Chekmarev, T. Z. Lygina, K. G. Egorova, A. V. Skvorcov

"We have conducted analytical and technological evaluation of sepiolite containing clay. The possible areas of application of the sepiolite have been investigated and complex methods of enrichment of natural sepiolite have been identified. It was determined that for preserving the structure of minerals after processing the most effective method of the natural agglomerates disintegration was the soft abrasion of the clay fraction up to 0,5 mm. Disintegration of sepiolite clay along with using high energy-stressed effects on the matrix can deteriorate the rheological properties of clay suspensions and reduce the yield of drilling mud and sorption properties. To improve the quality of clay powders we used combined gravity-modifying method of wet enrichment. After the wet enrichment the yield of drilling mud increased up to 12.7 m3/t, with the addition of MgO up to 20,3 m3/t. It was noted that drilling muds contenting more than 50% of sepiolite are stable in mineralized (salt) waters. Based on the studied activated sepiolite rocks we obtained the effective heat-insulating materials with relatively low thermal conductivity – 0,165 W/m·K, average strength – 7,29 MPa and water absorption-49,0%.INTRODUCTION The modern development of the Russian economy requires the implementation of scientific and technical tasks. The solutions of it involves a radical reduction in energy, heat losses and material consumption of products, rational and efficient using of all types of resources, as well as the using of new types of mineral raw materials and materials based on it. An example of a new type of mineral raw materials for Russia is sepiolite containing rocks, due to unconventional conditions for their soils accumulation in the climate of the Far North. Sepiolite is a unique type of nonmetallic mineral. It is formed in soils, marine and saline basins, occurs in carbonate and carbonate-clay rocks in the form of lenses and lens – shaped layers, rarely nodules, loose powdery masses, shell-like concretions. Sepiolite may have a soft porous macroscopic appearance or less often the structure of the fibrous mass. Color of sepiolite is from white to cream with gray, green, pink and even crimson shade depending on the degree of pollution. Sepiolite can be in two forms - a-sepiolite (parasepiolite), which occurs in the form of large packets of crystalline fibers and ß-sepiolite, which occurs in the form of amorphous aggregates or small flat rounded particles. The sepiolite fibers have a length of from 0.2 to 2 Å, width from 100 to 300 Å, the thickness from 50 to 100 Å (Geological dictionary, 1973)."

Jan 1, 2018

By G. B. Abaka-Wood

"The versatility of froth flotation has made it vital in the beneficiation of rare earth elements (REE) minerals from either high or low grade ores of complex mineralogy. There has been a significant increase in the tonnage of rich iron oxide tailings obtained from extraction of primary commodities such as copper and gold in Australia, which have been identified to have very low grade rare earth oxides (REO) (= 1%). There is a vast knowledge gap in the upgrade of REO from such tailings. The aim of this research is to investigate the feasibility of the use of fatty acids for the upgrading of REO from selected iron-oxide rich tailings. Two forms of fatty acid collectors (oleic acid and sodium oleate) were employed in this investigation. Bench scale flotation tests were carried out using a Denver D-12 cell.The effects of pulp pH, fatty acid dosage, particle size distribution (-150 +75 µm, -75 +38 µm and -38 µm) and conventional depressants (sodium silicate and starch) dosage on flotation recovery of REO were investigated. A comparison of the flotation results indicated that sodium oleate was the more efficient fatty acid for REO flotation at all the pulp pH investigated. The flotation performance is demonstrated to be particle size-dependent. The results on the effect of depressants dosage indicated that both sodium silicate and starch were unselective in reducing the recovery of hematite (Fe2O3) and quartz (SiO2) with corresponding decrease in REO recovery. Generally, Fe2O3 and SiO2 formed substantial contents of the flotation concentrates obtained, both in the absence and presence of depressants, which indicates liberation is a major challenge in achieving selective REO upgrade and recovery.The flotation tests carried out on the iron-oxide rich tailings suggest the possibility of REO upgrade using fatty acids, although particle size distribution and minerals liberation are key limiting factors in achieving selective REO upgrade and recovery."

Jan 1, 2018

By M. Prasad

Growing concern over increased levels of atmospheric carbon dioxide has prompted new interests in development of materials and techniques for its sequestration. Various research and developmental work on different aspects of carbon capture technology are being extensively carried out worldwide. The main objective of the present work is to synthesize a HAS material having high capacity and robust ability for recycling to capture greenhouse gases with special reference to carbon dioxide (CO2) from the sources from where it is released to the atmosphere. Existing CO2 capture techniques involves the use of solid materials that lack sufficient stability for repeated use or liquid adsorbents that are expensive and require significant amounts of energy. Keywords: greenhouse gases, carbon capture, solid adsorbent, HAS material

Sep 1, 2012

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

Green pellet strength including drop number and green compression is highly depended on particles size and shape. The used grinding method, ball mill or high pressure grinding roll (HPGR), directly vary the particle size and shape. Considering mode of pellet crack, green pellet is composed of particle-binder-moisture system. Different type of forces existed in such a system to create a stable green pellet: solid particle interaction, magnetic, binding and cohesive forces in the interface of particle-moisture. The pellet failure can occur at solid-liquid interface and/or through liquid phase. Pellet crack occurs when crack passed through entirely the plane failure. In this research, the effect of particle size and shape of pellet feed on green pellet strength has been investigated. It was deduced that green pellet strength highly improved by increase of specific surface area. The drop number and green compression strength of pellets prepared by HPGR was higher than ball mill. It was found that the main reason responsible for this difference was the particle shape. Capillary force is responsible for part of pellet force and improves by decrease of particle size. Also more elongated shape of HPGR particles resulted in higher capillary force due to thinner interface layer between particles. The less circular shape of particles lead to improvement of capillary force as can be occurred for HPGR particles. The rougher shape of HPGR particles resulted in higher wettability of particles and better diffusion of water among particles. In fact the rougher particles means lower connection angle. Aspect ratio of particles was of great importance of crack growth because the required energy of pellet failure increases directly. The required energy for pellet failure increases by increment of particle aspect ratio. The relationship among crack failure force, roughness and aspect ratio has been modeled considering 3 shape descriptors.

Jan 1, 2018

By Z. Naziemiec

Since several years in Poland a huge demands on mineral aggregates occur, for the reason of intensive development of housing and road industry, as well as industrial building. Limitations in re-sources of broken aggregates in Central and Northern parts of Poland cause, that both the non-waste production of aggregates with high quality and the production of alternative aggregates from recycling gain greater importance, nowadays. It entails increase in demands for crushing devices, which are easy and reliable in operating as well as inexpensive and enabling to obtain a good quality products. Jaw crusher, regarded as the most spread in Polish industry, meet these requirements, however, their crucial disadvantage is a large content of irregular grains in crushing products. Numerous investigations show, that the shape of grains is a significant feature of aggregates, which influences on durability and quality of produced concretes. The advantage of jaw crushers is their easy operation, low price as well as low amount of dusts (wastes) generated in comminution products in comparison to other types of crushers (i.e. hammer crushers).

Jan 1, 2014

By M. V. Sowmya

Batch biosorption experiments were carried out for the bio-remediation of Cr (VI) ions from aqueous solutions using Serratia marcescens, a Gram negative, heterotroph and Gram positive bacterial isolates from a chromite mine. The influence of various experimental parameters such as contact time, pH, concentration of Cr (VI) ions and amount of biomass was evaluated with respect to the uptake of Cr (VI). The bio-sorption of Cr (VI) was found to be quite rapid and the percentage biosortion was found to increase with increase in the equilibrium chromium concentration. The free energy of biosorption of Cr (VI) was estimated to be in the range of -23 to -25 kJ/mol for the chosen bacteria. The uptake of chromium by the bacteria was confirmed by EDX and FTIR spectroscopy. As a follow up of this study, bacterial strains resistant to hexavalent chromium were isolated from a chromite mine in Karnataka, India and identified as Arthrobacter sp., Micrococcus sp. and Exiguobacterium sp. using 16s rRNA sequencing. The efficacy of the bacterial isolates for Cr (VI) uptake was assessed and over 90% bioremoval could be achieved for Serratia marcescens and Micrococcus sp. isolate. Possible mechanisms of chromium uptake by the microorganism are discussed. Keywords: bioremediation, hexavalent chromium, biosorption, bioreduction

Sep 1, 2012

Calaverite is a gold telluride found in the Kalgoorlie region, Fiji, Cripple Creek Colorado and numerous other locations. It is known that a high pH is necessary for calaverite cyanidation, with the leach rate increasing substantially above pH 12 due to the hydroxide ion concentration. In most circumstances lime is used to achieve high pH, however lime saturates at approximately pH 12, limiting the maximum pH obtainable in a critical region for calaverite leaching. Plant observations, laboratory experiments and thermodynamic modelling show that the maxi-mum hydroxide ion concentration that can be achieved with lime (CaO) is strongly dependent on common ions. The presence of calcium, as commonly found in saline waters, substantially diminishes the maximum pH that can be obtained with lime. Conversely the presence of sulfate ions, as generated through oxidation of sulfides, substantially increases the maximum pH that can be achieved with lime. Sulfide oxidation during cyanide leaching of complex ores may generate acid and sulfate ions, making overdosing with lime at the front of the circuit, or staged addition down the leach train, important to maintaining the maximum hydroxide concentration.

Jan 1, 2014

By A. Vilinska

Microorganisms have a tremendous influence on their environment through the transfer of energy, charge, and materials across a complex biotic mineral-solution interface. Recent developments in biotechnology have not only aided hydrometallurgical leaching operations but also shown great promise in mineral beneficiation processes. The adhesion of bacteria on minerals alters the surface properties relevant to flotation and flocculation of minerals. The biomodification of mineral surfaces occurs through the attachment of microbial cells, oxidation reactions and adsorption or chemical reaction with the metabolite products. Several types of heterotrophic and chemolithotrophic bacteria have been successfully applied in flotation and flocculation processes for the last two decades. Al-though the potential of microorganisms in minerals beneficiation has been realised by several re-searchers from their laboratory investigations, the studies were mostly confined to pure mineral systems and there is hardly any sincere effort to apply the methodologies on ores. This paper presents a brief summary of the literature in bioflotation and bioflocculation, and attempts to outline new dimensions of research for a practicable application of this technology in mineral industry.

Jan 1, 2014

By W. Kobal

The extraction of nickel (Ni) and cobalt (Co) from the laterite deposit of Ramu nickel-cobalt Project in Papua New Guinea was performed in this study. Chemical analysis by Inductively Coupled Plasma (ICP-AES) atomic emission spectrometer, SPS-3000 (Seiko Instruments (Inc.), shows the ore contains 48% Fe, 1% Ni, 0.1% Co, 1.8% Al, 0.14% Mg, and 0.8% Mn. Characterization by X-ray diffraction (XRD) analysis of the laterite ore obtained from the mine site shows the ore contains 70 to 80% goethite (FeOOH), assuming Fe content of 48% is mainly from geothite. The main leaching parameters investigated include; slurry temperature, leaching time and sulphuric acid (H2SO4) concentration to evaluate nickel and cobalt extraction. For all experiments, 10g batch samples are put into 300 ml beaker containing 100 ml of sulphuric acid of varying concentrations (1M, 2M, 4M). During the leaching period, 5 ml slurry samples are withdrawn at different times and filtered to obtain filtrate for ICP analysis to monitor nickel and cobalt extraction. Solid samples at the end of all tests are also obtained by filtration and after drying, XRD and ICP tests are performed to monitor nickel and cobalt contents. According to the test results performed at normal atmospheric pressure, over 99% of nickel and over 50% cobalt were extracted into solution within 120 min at 95ºC in 2M H2SO4 solution. Similar results were obtained when only temperature was reduced to 90ºC, but cobalt extraction increased to over 70% when leaching time was increased to 240 min. Further reduction in temperature to 80 and 60ºC resulted in reduction of nickel and cobalt extraction. At the end of each leaching test, magnetite was seen to attach to magnetic stirrer. The study showed nickel can be completely leached into solution but cobalt only up to 70%. Keywords: atmospheric pressure, sulphuric acid leaching, nickel laterite

Sep 1, 2012

By M. Saghaeian, R. Hejazi, M. Farahani, M. Dehghani, A. Tohry

"Wet tailing dams of iron ore processing plants typically contain a significant amount of valuable minerals. In more recent years, due to the increase in iron’s prices and technological innovations, as well as the low energy consumption which required for processing of materials from tailings, dams can consider as potential valuable deposits. However, the production of iron concentrate from tailings is usually complicated where the high moisture content of the material, the high clay content and the presence of chemicals of processing such as flocculants, acids and flotation reagents, all make materials highly sticky which can be easily swollen. In the present paper, the optimization of operational parameters to recover ultrafine hematite iron ore from the wet tailings dams of the Chador-malu iron ore mine was investigated. The optimization of operational parameters, showed that with modification of the washing unit components for slurry making, the challenge of constraints from feeding the plant could be overcome. To decrease the magnetite content in the tail stream of the medium intensity magnetic separation (MIMS) and subsequently increase the efficiency, the orifice of the cleaner tail flow exit pipe was changed from 7 inches to 3 inch and yoke angle changed from 14 to 8 degrees. These changes increased mass yield by 3% and decreased the magnetite content in the final tailings to 1.2%. By recirculating the cleaner SLons of final tailings within the circuit, the solid percentage of the feed to rougher SLons decreased to around 15%, and as a result the matrices were not overloaded that easily, and mass yield increased to about 13% from 7%. All the above mentioned optimizations were achieved without significantly affecting the concentrate Fe grade."

Jan 1, 2018