Search Documents

By Y. G. Sun

This paper mainly reported separation manganese silver oxidized ores process by amylum de-gradation reduction and its influencing factors. When dosage is given according to nMn : nH2SO4 : n(C6H10O5)n : nH2O=1:k21.8: k116.66:30, the amount of up to 95.93% Mn leach rate and less than 2% silver loss can be obtained. Cyanidation process was used to extracted silver from leaching Mn residues. Silver leach rate could reach 94.15% at consumed amount of 1kg/t NaCN for 1h. Silver leach recovery rate was more than 92.27% by leaching Mn and cyanidation two-step processes so manganese and silver were separated effectively.

Jan 1, 2014

In recent years, coal beneficiation has gotten considerable attention. Selective oil agglomeration has been accepted as the best method to produce clean coal with a high removal of pyrite sulphur. In this study, spherical oil agglomeration of Datong coal fines was carried out using diesel oil as a bridging liquid. The oil agglomeration has a surface properties based on coal cleaning technique. The effects of fundamental parameters have been investigated including the concentration of bridging liquid, the size of coal particle, the solid content of slurry, the agitation time and rate, pH, surfactants on the agglomeration performance and various salts on the ash rejection and removal of pyrite of the agglomerated products. The optimum conditions of particle size, diesel concentration, solid content, agitation speed and time, pH and the dosage of active agent have been determined as less than 8µm, 20wt%, 1200r/min and 10 minutes, 7.5g/t and 100g/t, respectively. Under these conditions the ash content in the products can be achieved 1.5% below, the ash rejection was up to 92%. It has been observed that ionic strength of the aqueous medium affects the agglomeration performance. The precombustion coal cleaning process based on improved selective agglomeration results in high ash and pyrite sulphur removals. Over 80% removal of pyrite sulphur can be achieved from run-of-mine coals by offering a more cost-effective sulphur reduction solution rather than any other SO2 removal technology. In addition, the removal of pyrite sulphur is very necessary for not only the prevention of environmental pollution but also economical reasons.

Jan 1, 2014

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By V. A. Chanturiya

There is an obvious disproportion in Russia gold-mining industry between the structure of gold reserves and the gold-mining techniques. The bulk of gold (over 70%) is extracted from alluvial deposit, 20%~25% from bedrock occurrences and 5%~7% from complex copper-zinc and polymetallic ores. The proved gold-bearing reserves are distributed as follows: alluvial ?19%, bedrock ?80%, the latter being sufficient to supply gold at the current production level for 100 years to come. In Russia, like elsewhere in the world, development of primary gold deposits is considered a first-priority line of development for gold-mining industry. Most of the gold-containing ores characteristic of Russian gold deposits are resistant ores with gold content varying between 3 ppm and 5 ppm usually showing quite low gold and silver recovery by cyanidation. Processing resistance of gold-containing mineral complexes is related to the presence of gold particles of submicrometric (<1.0 µm) and nanometric (10~100 nm) size, mostly asso-ciated with pyrite and arsenopyrite. Therefore switching over to processing bedrock entails a num-ber of technological problems that stem from chemical and physical resistivity of ores. The chemical resistivity can be overcome through flotation, oxidation roasting, autoclave leaching (biohydro-metallurgical oxidation), etc. The physical resistivity can be dealt with by resorting to traditional power-intensive methods,e.g. grinding to a ?40µm size, thermal treatments of sulphide concentrates and non-traditional high-energy methods of liberating the sulphides by means of power attack, e.g. electro-chemical oxidation, exposure to electron beam radiation and other methods. The modern non-traditional processes for treatment of rebellious noble metal-bearing ore, aimed at improving disintegration efficiency for finely dispersed mineral complexes are analysed. Advantages and perspectives of a new high-efficient, energy-saving and ecologically safe process of the nanosecond high-power electromagnetic pulses (HPEMP) effect are proved. The said process provides a stable increase in the valuable component recovery at lower energy consumption and production costs of the finite product at the stage of dressing rebellious gold-bearing ores and concentrated products. The experimental data prove high efficiency of the preliminary impulse treatment, thus, the increase in the gold recovery at the cyanidation stage amounted to 4%~12% from rebel-lious ores, 10%~30% from gravity concentrates, 5%~45% from flotation concentrates, 30%~80% from oil flotation tailings.

Jan 1, 2014

By T. Kumaresan

The Bayer process used for refining bauxite to smelting grade Alumina serves as the linchpin of the Aluminum production industry worldwide. Even though the process is well established, the presence of impurities in the liquor affects the quality of product and imposes a major economic cost on the industry. This review article focuses on the issues pertaining to Gibbsitic (Al2O3.3H2O) precipitation circuit. The comprehensive review provides a basic understanding of the aluminum trihydrate precipitation and agglomeration phenomena. Crystal growth rate and agglomeration play a significant role in determining the output PSD of agglomerates. Hence, the effect of certain thermodynamic and hydrodynamic parameters along with the impact of impurities (oxalates, aldols, acids etc.) and additives on hydrate growth has been reviewed.

Sep 1, 2012

By B. Das

The processing of banded iron ore by direct anionic and reverse cationic flotation to produce pellet grade concentrate is investigated. This low-grade iron ore, known as banded hematite quartzite (BHQ) contains 41.8% Fe, 41.5% SiO2, 1.2% Al2O3, and 0.5% LOI. The flotation behavior of BHQ is studied by varying the effect of concentration of collector, frother, dispersant and pH. Oleic acid and dodecylamine are used as the anionic and cationic collectors respectively. The parameters that gave the best results in cell flotation are utilized in 100 mm diameter flotation column. All the results are compared with regard to the iron grade and recovery in concentrate. It is observed that, anionic collector with dispersant dosage of 220 g/ton, at pH ~8.5 is selective and yielded a high-grade iron concentrate with low silica as impurity. Also, it is possible to achieve an iron concentrate with 64% Fe at 30-37% weight recovery. The characterization studies of the BHQ ore using X-ray diffraction (XRD) technique and liberation analysis with QEMSCAN® are carried out. The sample contains 58.8% hematite and 37.7% quartz and the liberation of hematite particles are found to be 90.3% in -25 µm size. An alternative statistical modeling approach called response surface methodology was also undertaken to optimize the operating parameters in order to maximize the iron grade and recovery. The predicted results by the model are in agreement with the experimental values.

Sep 1, 2012

By Ashutosh Shandilya

Froth flotation is a selective separation process and rarely used for beneficiation of limestone in the world as compared to other minerals and also mostly known conventional methods of up gradation of ROM including wobbling, selective mining, sorting, preblending etc. Limestone is mainly used in the manufacture of cement, steel and chemical industries. High grade limestone deposits are depleting day by day and the requirement of the industries have to be met by beneficiating the low grade limestone deposits in the world. And because of marginal quality of limestone, it cannot be directly used in cement industry. At ACC Madukkarai cement works, Coimbatore, Tamilnadu, full fledged mineral beneficiation process is adopted to enhance the quality of low grade lime stone from 38-42 % CaO to 45-47 % CaO and silica reduced from 19-22 % to 11-13 % by use of oleic acid (commercial grade and vegetable origin) 0.38 kg/ton of limestone and caustic soda 0.05 kg/ton of limestone. Keywords: OK-8 Cells, Froth flotation process, Beneficiation studies, Low-grade lime stone, Oleic acid, % solids, Pulp density, Ph, Iodine value, saponification value, Denver cell

Sep 1, 2012

By M. Saghaeian, R. Hejazi, A. Dehghani Ahmadabadi, M. Zare

"In the most iron ore beneficiation plants, reverse flotation is the best method for removing silicate gangues from final iron ore concentrate. Many previous studies show, if the major portion of impurities include quartz minerals, the flotation process is simple, but if iron silicates are dominant, reverse flotation is so complicated and mostly not very effective. In this study which was performed on the Sangan iron ore concentrate, the performance using of reverse flotation and magnetic flotation separator for elimination of silicate gangues from the magnetic iron concentrate was investigated. The operational parameters for reverse flotation are considered as: collector and frother types and dosages and also modifiers. But for magnetic flotation separator parameters were magnetic field intensity as well as overflow and underflow water rates. Results showed that reverse flotation has not a significant effect on the elimination of impurities. Because of the silicate gangues of Sangan concentrate including a mixture of quartz and iron silicates (amphibole, pyroxene and feldspar), so downgrading of the SiO2 content for the flotation concentrate was rather low and only average reduces of 20.60% were possible. But the findings of using magnetic separator was more satisfactory. Results of the weight recovery, iron grade and also SiO2 and S grades of final concentrate were better with magnetic flotation device. So at the best and optimum condition, we could reduce 51.01% of the total silicate (SiO2~ 2.19%) along with 74.66% of sulfur content (S~ 0.076%) and concentrate weight and Fe recoveries of 92.04% and 94.51% respectively, final Fe grade of 68.73%.INTRODUCTION Chemical/traditional flotation is one of the most effective methods for separating valuable particles from waste minerals, which is used in most mineral processing industries. In the iron ore processing industry, the major impurities present in iron ore concentrate include sulfur, silica and phosphorus (Bruckard et al, 2015), which are often carried out by reverse flotation methods for the removal of sulfide and oxide impurities (Donald, 1967: Araujo et al., 2005: Ma, 2012)"

Jan 1, 2018

By Ye Chen, Jianhua Chen, Meng Liu, Yuqiong Li, Xiao Mu, Cuihua Zhao

"Sulfidization-amine is the most effective method for the recovery of smithsonite (ZnCO3), however the interface interaction details remain unclear. The sulfidization-amine flotation mechanism of smithsonite has been studied by Density Functional based Tight Binding (DFTB+) method in this paper. The slab model of ZnCO3 (101) surface was built and the adsorptions of a monolayer of HS- and S2- ions were conducted to model the sulfidization effect on the ZnCO3 (101) surface adsorption. DDA hardly interacts with the hydrated ZnCO3 (101) surface. Under the low concentration of Na2S, HS- ions form a Zn-SH-SH structure on the ZnCO3 (101) surface, which hinders the interaction between DDA and surface Zn atoms. Under the high concentration of Na2S, a layer of ZnS is formed on ZnCO3 (101) surface, which is favorable for the adsorption of DDA on the surface. This is consistent with the flotation practice where smithsonite flotation requires a large amount of sodium sulfide. The results could provide a microscopic investigation into the sulfidization-amine flotation mechanism of smithsonite.INTRODUCTIONSmithsonite (ZnCO3) is an important and typical oxide mineral of zinc. It is a semi-soluble salt mineral with a solubility product constant of 1.46 × 10-10 (Weast, 1973). The most common and effective method to recover oxidized zinc ores is froth flotation (Caproni et al., 1979; Pereia and Peres, 2005; Kashani and Rashchi, 2008). It is well known that the flotation of oxidized zinc minerals is much more difficult than the flotation of zinc sulphide minerals (Hosseini and Forssberg, 2007).The recovery of zinc oxide ores with poor floatability attracts more and more attention due to the depletion of easy-recovered of zinc sulfide ores.Sulfidization-amine flotation, which using Na2S as sufidizing agent and amine as collector (Mckenna et al., 1949; Rey, 1954; Abramov, 1961; Rey, 1979; Hosseini and Forssberg, 2007). This method is the most successful technology used for zinc oxide minerals flotation in large-scale industrial applications since it was invented in the 1950s (Önal et al., 2005; Pereira and Peres, 2005). There have been numerous experimental researches on the sulfidization-amine flotation of smithsonite. Shi et al., (2013) studied solution chemistry of smithsonite flotation system. Feng and Wen (2017) studied the formation of zinc sulfide species on smithsonite surfaces and its response to flotation performance. Wu et al., (2017) investigated the sulfidization behavior of smithsonite with the use of zeta potential, inductively coupled plasma (ICP), scanning electron microscope (SEM), and X-ray photoelectron spectroscopic (XPS). Their measurement results confirms the chemisorption of sulfur ions and the formation of ZnS film on the smithsonite surface after Na2S treatment, however the influence of HS- ions on the surface and the influence of sulfidization on the amine adsorption have not been discussed."

Jan 1, 2018

By Osvaldo A. Bascur

One of the most vigorous of the continuous improvement methodologies is Six Sigma. While usually associated with improving manufacturing and product quality, leading manufacturers are using it to improve their extended supply chain and logistics capabilities. At the same time they are improving reliability, some companies have cut hundreds of millions of dollars of fat out of their supply chain. Mine to Mill optimization is a transformation of culture from processing tons to processing a quality feed size distribution which reduces the overall operational costs and add the highest value to the mine. This is not a constant endeavor. As such, a dynamic performance monitoring and diagnosis is necessary. We will review a systemic way to performance improvements and avoiding metal losses from the blast to the metals. We show the requirements of using raw data to analysis the data to define operational maps which provide assistance to run the mine and mill. A case study is provided with the mine and mill data was integrated combining process control and quality information resulting in reduction of water and energy consumption while improving the overall value of the mine. The results of reengineering the current system with this SIX SIGMA Strategy had the following results: an increase of ore milling: 4.6% decrease of mil power: 3.9%, decrease of fresh water consumption: 6.8%, with a total of net profits: US$ 31.8 million, the PI System infrastructure contribution: US$ 7.95 million. These estimates were for the period 2009/04/04 to 2009/12/31.

Sep 1, 2012

By J. Botula

In the region of the North-Bohemian Coal Basin and its environment, there, in a row of places, are found the accumulations of rocks of the sedimentary and pyro clastic origin, the preliminary composition of those shows the possibility of their being utilized for the production of ecologically sparing natural Fe- and Ti- pigments and filling substances. In many places of the regions of Chomutov and Podborany and near Bilina and also in other places, there are found raw stocks perspective for the preparation of yellow up to ochre-brown, red, brown-red and green dyes. The target of project is the verification of dispensable reserves, their mineralogical composition and chemical and physical attributes, verification of treatment ways of Fe-and Ti-pigments separation (hydrocyclones, magnetic and electrostatic separation) and their stabilization and technological painting attributes for applications in colors, coating and plastic masses, mortar mixtures etc.

Jan 1, 2014

By D. Moradkhani

Copper metal has important role in the basic industrials, as if it did not exist, modern human life would not develop! Copper leaching, as the first step, is important step in copper production processes. In this research, efficient factors on the leaching have been investigated. For this reason, four efficient factors on leaching namely pH, liquid to solid ratio (L/S), temperature and time, as independent variables, were optimized using response surface (RSM) with D-optimal. A quadratic equation was used to create response and contours. According to the results from analysis of variance (ANOVA), the value of determination coefficient (R2=96.77%) indicates that the model was good fit. Optimum experiment condition also was found: pH of 1, L/S of 8.24, temperature of 26.06 ? and time of 43.64 min. At this condition, the maximum recovery of copper was equaled to 92/38 in which good desirability achieved.

Sep 1, 2012

By N. Gurulaxmi Srikakulapu

The demand for high-grade iron ore has increased the importance of beneficiation of low-grade iron ores. The captive mines of Tata Steel Limited, India has reserves of Banded Haematite Jasper (BHJ) ore assayed 40% Fe, 40% SiO2 and <1% Al2O3. QEMSCAN study has revealed haematite and quartz as a major iron bearing and gangue mineral phases respectively. Liberation characteristics have showed 80% liberation can be obtained at particle size below 10µm. In the present study, reverse cationic froth flotation of BHJ using ether diamines is explored in Denver-D12 flotation cell. Polynomial response surface regression equation coupled with six-factor Box-Behnken design of experiments is used to generate the correlation between process separation efficiency and flotation parameters. Flotation studies of BHJ indicated that concentrate of 62% Fe can be achieved with 62% Fe recovery from Jig concentrate at optimum conditions. The obtained product can blend with pellet fines to feed in blast furnace. Keywords: banded haematite jasper, flotation, box-behnken design, response surface methodology

Sep 1, 2012

By K. B. Venkatesh

In view of the importance of size reduction operations from the energy consumption point of view, during the past one hundred and fifty years a number of attempts have been made to develop a general energy-size relationship. However, to date it has not been possible to clearly define the scope of application of various laws proposed, though Bond law has been widely used with a moderate degree of success. It was, therefore, decided to carry out a thorough analysis of the batch ball mill grinding data available in the literature on several minerals that were ground under normal range of operating conditions. In particular, relationships proposed by Bond, Kapur, Voller and Morrell were examined in detail. It was found that the relationship proposed by Kapur in terms of the mean particle size provided a more accurate basis for estimation of energy. The value of the exponent of mean particle size in this relationship, a, is same as the exponent of the particle size in the expression for the grinding rate parameter: ki = Axia, provided the particle size distribution range corresponds to the self-similar or self-preserving regime. In this regime, mean particle size is proportional to the 80 percent passing size and size modulus. From the practical application point of view, it was possible to describe the variation of µ1 over limited, but significantly broad size range, using a constant value of a. Thus, by carrying out a few batches, grinding experiments over the size distribution range corresponding to the contents of the production mill, the applicable value of a can be determined. Keywords: energy-size relationship, ball mill, mean particle size, self-similar size distribution regime

Sep 1, 2012

By Liu Jin

"In order to reduce the dosage costs and increase the economic benefits of a full floating process in a low grade complex multi-metals W-Mo ore, based on the study of the magnetic characteristics of the main gangue minerals, a joint process by magnetic separation and floatation technology is adopted. The first step of the flowsheet is to recover magnetite by magnetic separation, then remove the magnetic gangues by high gradient magnetic separation (HGMS) and finally recycle the W-Mo from the magnetically separated tailings by flotation. Results of the lab experiment show that in comparison with the full flotation process, the floatation feed tonnage of the combined flowsheet are only 46%. The grade and the recovery of Mo in the rough Mo-Bi concentrate is similar with the original one while the WO3 in the tungsten rough concentrate is increased from 3.85% to 6.64%. The dosage costs are reduced by 53%. The new process can significantly improve the plant economically. INTRODUCTION With the continuous exploitation of scheelite resources, the easily obtained resource is gradually depleting. The ""lean, fine and complex"" scheelite resource has become the main research object of tungsten beneficiation (Lou et al., 2010) (Xiao et al., 2013). The passive situation of tungsten beneficiation can be reversed by enhancing technological innovation and investment in science and technology, changing the business philosophy and mode of production, optimizing the process structure and process conditions, improving various technical indexes and reducing production costs of reagents, which will maximize economic benefits (Jiang et al., 2012 ) (Zhu et al., 2016). A polymetallic deposit of tungsten molybdenum bismuth original process adopts a full flotation process. With the expansion of stope mining, the content of valuable metals in the ore continues to decrease, resulting in a high cost per ton of concentrate produced and a low output value (Li et al., 2015)."

Jan 1, 2018

By Bo Feng

The development of surface charge of serpentine mineral and implications for sulphide ?otation have been studied through flotation tests, sedimentation tests, zeta potential measurements and optical microscope photos. The results show that the serpentine mineral was positively charged at an extensive pH range, with an isoelectric point (IEP) of 11.9. The magnitude and sign of the pyrite particles were pH dependent and were negative for pH values above 2. At pH value 9, where ?otation of nickel sul?de ores is routinely performed, serpentine and pyrite particles attract through an electrostatic mechanism. Slime coatings of serpentine adhere to the surface of pyrite, reducing pyrite flotation recovery. The removal of magnesium ions from the serpentine surface by acid leaching results in a decrease of serpentine IEP and eliminates the adverse effect of serpentine on pyrite flotation. Therefore, it has been clearly established that the surface charge value developed in the serpentine/aqueous electrical interface is a function of the serpentine surface incongruently dissolution. As a result of hydroxyl dissolution, the magnesium ions are left in serpentine surface, which is responsible for serpentine surface charge. The methods, which can remove magnesium ions from serpentine surface, can be used to eliminate the adverse effect of serpentine on pyrite flotation.

Sep 1, 2012

By Y. M. Zhao

The dry coal preparation technology based on air dense medium fluidized bed is an innovative dry highly efficient technology of coal by introducing fluidization technology into beneficiation.. A modularized 40-60 tones/hr system (KZX-40) with an air dense medium fluidized bed separator was established. The construction cost of the modularized system is only 1/3 of the traditional wet heavy-medium coal preparation plant construction cost with the same capacity, and the consumption of dense medium can be reduced by 50%-60%. The footprint and volume of the system are decreased by 75% and by 89.81%, respectively. These facts show the improved intensity, efficiency and economy of modularized coal preparation technique. The modularized KZX-40 system can be used to separated 50-6 mm coal over a separation density range of 1.3-2.2g/cm3 depending on the variation of <1mm fine coal content. The separation efficiency of the system was investigated at low and high separation densities by float-sink experiments. The partition curve of the products at low separation density shows that the separation density (d) is 1.33g/cm3, and the probable error (E) value is 0.05g/cm3. Using 50-6mm coal with an ash content of 55.35% as feedstock, at a high separation density of 1.61g/cm3, the clean coal with an ash content of 14.67% and the tailing with an ash content of 71.26% are produced with an E value of 0.06g/cm3. It is clear that the modularized KZX-40 system is suitable for separating 50-6mm coal effectively. During the dry coal preparation process, the dust is removed by the bag collector and recycled back into the separator. So the system has the advantages to work without environmental pollution and water. The modularized system greatly reduces the construction and operating costs and decreases the area and volume required, compared with wet dense medium system. The system is applicable to the coals located in arid regions and also to the coals that tend to slime during wet separation. Keywords: modularized, KZX-40, fluidized bed, beneficiation

Sep 1, 2012

By P. Altinkaya, O. Celep, H. Deveci, E. Y. Yazici

"Copper-bearing gold ores have proved difficult to treat in conventional cyanide leaching process owing to prohibitively high consumption of cyanide by readily soluble copper minerals interfering with gold extraction. Cyanide leaching of gold from copper-rich ores can be improved by intensive cyanidation or application of physical and chemical pre-treatment methods (e.g., ultra-fine grinding, roasting and leaching). In this study, nitric acid leaching of a copper-bearing pyritic concentrate (0.3% Cu, 62 g/t Au and 110 g/t Ag) as pre-treatment prior to cyanidation was investigated. The mineralogical analysis of the concentrate has revealed that it is composed of mainly quartz (25%), pyrite (32.7%), sphalerite (5.37 %), galena (2.12 wt %) and anglesite (1.13 %). Arsenopyrite, chalcopyrite, covellite and bournonite were also detected as minor phases present. Previous studies carried out by the authors showed that direct cyanidation (1.5 g/L NaCN) of the as-received concentrate (d80: 80 µm) produced low gold (45% Au) and silver (46% Ag) extractions. Nitric acid pretreatment of the as-received concentrate was performed for 5 hours at 1-5 M HNO3 and 80oC. In these tests, 65% Cu/Pb and 94% Zn were leached. The nitric acid pre-treatment improved the extraction of gold and silver in subsequent cyanide leaching (1.5 g/L NaCN) to 82% Au and 87.5% Ag with a concomitant decrease (up to 54%) in cyanide consumption. It can be inferred from these findings that the removal of copper from the concentrate and the liberation of the occluded gold by nitric acid leaching as pretreatments can be appropriately employed for the treatment of the copper-bearing pyritic concentrate with high gold/silver content. INTRODUCTION Refractory ores are often characterized by their low amenability to cyanide leaching resulting low (often <80%) Au/Ag extractions (Bhappu, 1990; Celep et al., 2009; Marsden and House, 2006). One of the most common causes of refractoriness is the physical or chemical encapsulation of submicroscopic or fine-grained gold in sulphide minerals such as arsenopyrite and pyrite (La Brooy et al., 1994; Vaughan, 2004). To render refractory gold ores/concentrates amenable to cyanide leaching, the decomposition of sulphide minerals within a pre-treatment process to expose the encapsulated gold grains to the action of cyanide is required. In this regard, roasting, pressure oxidation and biooxidation are commercially used processes for pretreatment of arsenopyrite/pyrite gold ores/concentrates ahead of cyanide leaching (La Brooy et al., 1994). Presence of cyanide-soluble copper minerals in the ore leads to low gold recoveries and high cyanide consumptions under conventional cyanide leaching conditions. High cyanide concentrations (CN:Cu>4) should be employed to achieve high gold recoveries from copper-rich gold ores/concentrates. This may require recovery of cyanide from effluents. In this regard, SART Process (sulphidisation-acidification-recycling-thickening) employed industrially for recovery of cyanide and copper as a by-product. This process simply relies on the addition of sulphide (as Na2S, NaSH or H2S) to the leach solution prior to the acidification to pH 4-5. This results in the precipitation of copper as Cu2S and occurrence of free cyanide which is recycled to the leaching circuit after S/L separation (Dai et al., 2012)."

Jan 1, 2018

By Sanjeeva Latchireddi

The effective utilization of the energy in comminution devices depend on how efficiently the broken particles leave the breakage field as soon as they reach product size. In crushers the transport of broken particles smaller than CSS is done by gravity (vertical) thus allowing the energy to be applied to new particles. However, in AG/SAG mills, gravity becomes the energy field and the transport of particles is horizontal which needs a suitable discharge mechanism and has been found to have significant effect on grinding efficiency. The material transport in AG/SAG mills depend on how efficiently the discharge system (grate and pulp lifters) operates. Material transport plays a significant role on efficiency of horizontal grinding mills ? AG/SAG/Ball mills. The magnitude of benefits that can be achieved with efficient material transport in AG/SAG mills has been demonstrated in a Greenfield milling operation at Mirabela Mineração?s SantaRita Nickel operation located in northeastern part of Bahia in Brazil. This grinding circuit was commissioned in October 2009, which was designed as a typical SABC circuit to grind 4.6 mtpa (575tph) to produce a P80 of 125um with 10-12% ball charge in SAG mill. However, it has been operating as ABC circuit without any grinding media in SAG mill. The nameplate design capacity has been achieved in few days and has gradually increased to an average of +800 tph and still it is operating in ABC mode. The milling circuit commissioning resulted in small and relatively simple measures to rectify, which was reflected in the rapid commissioning of the milling circuit and it achieved the nameplate capacity within days. The Santa Rita grinding circuit consists of one 30?x 15.4? 8.5MW SAG Mill fitted with Outotec patented Turbo Pulp Lifters (TPL TM ) in close circuit with HP400 short head pebble crusher and one 20? x 28.4? 5.5MW Ball Mill in closed circuit with Warman cyclone cluster fitted with 10 x 26? CAVEX cyclones. This paper examines the comminution design process, operating philosophies, experiences, post commissioning optimization, and future development works. Evaluation of the milling circuit performance relative to the design criteria is also discussed. Keywords: Autogenous Grate (AG), Semi-Autogenous Grate (SAG, Turbo Pulp Lifter (TPL)

Sep 1, 2012

By M. Taheri

Multiple Attribute Decision Making (MADM) method is applied to select tailings site of the Gol-e-Gohar Iron Ore Processing Plant in the Kerman province, south-eastern of Iran. To select tailings site, screening is applied on eight location proposed by Binnie and Granges. Consequently three sites identified for further studies. Evaluation factors include only the most important factors such as efficiency ratio, elevation and distance to processing facilities, occurrence of faults and fractures. Crisp values such as efficiency ratio, elevation and distance can be determined by measurements and calculations, but some factors such as occurrence of faults and fractures are presented as linguistic values that can be described with triangular fuzzy numbers. Based on evaluation values obtained an optimal tailings site can be selected using a modified Technique of ranking Preferences by Similarity to the Ideal Solution (TOPSIS) given crisp data and linguistic variables as the alternatives of attributes. Each attribute?s weight is assigned using the analytic hierarchy process. The final ranking order aids in the selection of tailings site. Finally, the stages of modified TOPSIS method were applied and site No.2 situated in 5400m to the mill was selected as the best alternative.

Jan 1, 2014