Search Documents

By Scott D. Neely, Donald R. Clark

"An existing landslide located at the southeast corner of the Telluride Regional Airport has been in an active state of failure for several years. The presence of the landslide has represented an on-going liability for the Airport, the Federal Aviation Administration and the Colorado Department of Transportation. A catastrophic failure of this landslide occurring in a manner similar to that which occurred at the Airport in 1987 has posed an on-going threat to closing Colorado State Highway 145 south and below the slide area. The existing landslide has been characterized as a series of multiple failed block areas located downhill of the airport runway that have occurred in severely weathered Mancos Shale.A total of 12 alternatives were evaluated to mitigate the landslide, including the preferred alternatives of either partial or total landslide removal. However, prior development has left essentially no place on the airport property that would allow for the disposal of the landslide debris for either the total or partial removal alternatives, and the closest off-site disposal area was approximately 40 miles from the site. As a result, in-situ stabilization of the landslide, including a primary system of isolated tie-back anchor plates with strand anchors, and a secondary system of high strength steel mesh and intermediate anchors was selected for the ultimate design of the project to stabilize the landslide in place.For design purposes, geotechnical characterization of the slide area was accomplished through geological mapping, conventional borehole exploration and geophysics using multiple electrical resistivity. The paper discusses the design process utilized and the unique challenges faced one-third of the way through construction when discovery of a survey error required redesign of the entire landslide mass stabilization system using the prefabricated anchors that had already been delivered to the project.INTRODUCTIONTelluride Colorado is located at the toe of the Colorado Rocky Mountains on the western slope. The Telluride Regional Airport is located on Deep Creek Mesa about 5 miles west of the town of Telluride.The landslide is located at the southeast corner of the airport just below an abandoned portion of the quarry access road on a south facing slope. The quarry access road is located below the elevation of the runway and outside the elk fence that surrounds the air traffic area of the airport property. Since the reconstruction of the runway, the access road to the quarry and the construction access road for the reconstruction of the airport runway and safety area were rerouted to stable ground north of the previous access road location and off of the head scarp of the landslide."

Jan 1, 2015

By Zhou Haizuo, Diao Yu, Zheng Gang

"The conventional design method for the embankment supported by DM columns usually assumes the simultaneous failure of all the columns. However, the progressive failure may occur in practice, especially considering that many researches have justified the critical load of DM columns is bending moment. In this study, a finite difference method was adopted to simulate the embankment on soft clay improved by DM columns. An increasing surcharge was applied on the embankment surface to investigate the mechanism of the progressive failure of columns beneath embankment. To capture the brittle bending failure of the DM columns, the model employed a cut-off method, in which the column was separated on failed section as long as the ultimate bending failure was reached. Furthermore, high-strength DM columns were used to enhance the global stability of embankment in this study. The numerical results showed that the ultimate bending failure was first reached at the column beneath embankment toe, and then a continuous collapse extended to the column beneath the embankment shoulder. It is found that the reinforcement could be obviously effective when the reinforced area of high-strength DM columns was extended to a certain area.INTRODUCTIONDeep mixed (DM) columns have been commonly used as a soil-improvement technique to increase stability and to reduce settlement of embankment. Research on failure modes of DM columns owing to embankment fill and surcharge has been the subject of interest for a number of investigators (Miyake 1991; Kitazume 2000; Han 2005; 2006).The potential failure modes of DM column include bending, inclination, shearing, rotating, soil flowing and a combination of these modes (Kitazume and Terashi 1991; Broms 1999). Many researchers have found that bending failure of DM columns was more critical than the shear failure. A centrifuge test was performed by Kitazume (2000) and the results showed that the columns failed in bending before shear failure. In addition, several numerical computations illustrated that design method using the shear strength overestimated the stability of embankment over DM columns (Han and Huang 2005; 2006; Navin 2006; Liu 2007; Wang 1996). In practice, an equivalent shear strength method based on bending failure could better reflect the stability of embankment (Zheng 2010; China Code JGJ79-2011)."

Jan 1, 2015

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By Arash Khosravifar Ph. D. P. E., Thomas Torkelson P. E., Milad Souri Ph. D. P. E.

Kinematic demands from lateral ground deformations can be a major cause of damage to maritime and highway transportation structures such as wharves, piers, and bridges. These kinematic demands are different from the ground deformations in the free field in that the resisting forces from piles will reduce the ground deformations to some extent (i.e., pile pinning effect). Current design codes for wharf structures allow the beneficial resisting forces from pile pinning effects to be incorporated in pseudostatic slope stability analysis (e.g., ASCE/COPRI 61-14). While design guidelines that are specifically developed for bridge foundations provide recommendations on how to incorporate the pile pinning effects (e.g., Caltrans 2012), their applicability to wharf structures need to be evaluated. This study uses the results of a large-scale centrifuge test on a pile-supported wharf structure to evaluate the accuracy of available Newmark sliding block analysis in estimating the lateral ground deformations. Pile pinning effects are incorporated based on the approach outlined by Caltrans. The results of this study support the use of existing pile pinning methods that were primarily developed for bridge foundations in maritime structures (e.g., wharves and piers). It was found that median Newmark displacements provide a good estimate of the permanent end-of-shaking displacements and that the median plus 1 standard deviation Newmark displacements provide a good estimate of the peak transient displacements. Design considerations for use in the Newmark sliding block analysis to estimate the kinematic demands on piles are discussed.

Oct 1, 2022

By Shawna Munn, Nadir Ansari, Toben Jerry

With ever increasing demands on space in urban environments and smaller available footprints, buildings are being designed to increasing heights to meet the need. This case study discusses the increasing challenges in developing projects within urban environments with smaller available footprints and increasing building heights. The One, Canada’s tallest residential building under construction will stand at 85 storeys and is located at one of the most prominent and built up intersections in Toronto, Yonge Street and Bloor Street. This led to many challenges in design and construction of the shoring and foundation work, including the required design capacity of the foundations for the supertall building and proximity of the large diameter drilled shafts to the excavation shoring wall. This case history describes the shoring design option evaluation, performance, and lessons learned to date throughout construction of the building foundations within a small congested site. PROJECT OVERVIEW The One, Canada’s tallest residential building under construction by Mizrahi Developments, is a supertall building that will stand at 85 storeys and 306 m (1005 ft). The first 18 floors will be comprised of retail, restaurants, and hotel with luxury residential condominium units in the tower above. The project is located on the Southwest corner of Yonge Street and Bloor Street, one of the most prominent and built up intersections in Toronto. The L-shaped excavation measures 58 m by 47 m (190 ft to 154 ft) and ranges from 22 m to 28 m (72 ft to 92 ft) in depth with one internal corner projecting 11 m (36 ft) into the site.

Jan 1, 2019

By Chris Normand, Paul Volpe, Eric Wey, Howard Perko, Burt Ogilvie, Patrick Murray

"A refinery expansion project for Marathon Petroleum Company in Southern Louisiana required existing medium to large pipe racks to be expanded for additional capacity. Foundation modifications were necessary in order to add levels to the existing pipe racks. New piles were added and existing pile cap foundations were expanded. Several different pile types were considered. Custom designed large diameter helical piles were chosen, because they can be installed quickly with low overhead restrictions, produce minimal soil spoils, and are cost effective. The load capacity required for piles was higher than typical, off-the-shelf helical piles. In particular, the lateral load capacity demand was high due to wind loads of a hurricane prone region. Methods used to design and size helical piles are summarized including capacity to torque ratio estimation for composite helical piles. Pile load testing was performed in order to confirm design capacities of the helical piles under axial and lateral loading. Measured axial and lateral deflections compared well with predicted values. This case history evaluates the effectiveness of modern helical pile design methods within the context of a real and practical example.INTRODUCTIONAs the capacity of modern installation equipment increases, large-diameter helical piles are being used to support higher loads in more diverse applications. Currently, large-diameter high-capacity helical piles are used for electrical power transmission, power generation, high-rise buildings, bridges, and industrial applications. This case study regards a 2.5-mile pipe rack modification project within an existing refinery. One of the many challenges for engineering and construction of refinery revamp projects is determining how to effectively expand the capacity of existing foundations for additional equipment, piping, and other facilities. Custom designed large-diameter helical piles provided an effective solution to the challenges faced when expanding the capacity of existing pipe racks."

Jan 1, 2017

By Rob van Dorp

"AbstractThe Monitoring & Instrumentation Committee (MIC) of DFI Europe has the objective to support DFI members in concern of risk management of geotechnical matters, where monitoring and instrumentation have added value.Work of the CommitteeA study by the committee showed that there are already several existing (national) guidelines. They all have their strengths and limitations and their focus may vary a little per country due to local regulations and typical local building activities, but the main question remains what added value another new guideline would have. More likely it would add to the confusion instead of providing overview.Companies with larger experience in geotechnical monitoring (often larger consultancy firm, contractors or clients) are already quite familiar with its benefits do not really need a new guideline in how to design and effectively apply sophisticated geotechnical monitoring systems for special projects.Therefore the aim of the MIC is to focus a little more towards smaller organizations - that are less familiar with monitoring and instrumentation - and the more ‘regular’ type of project that they are mainly involved in. The MIC wants to create a tool which helps them to create risk awareness, to understand the benefits of geotechnical monitoring and to provide them information about how and where to find the right partners and equipment to setup and apply appropriate monitoring systems for their projects.Monitoring and instrumentation benefits are for example:• Risk control during construction stage;• Costs reduction in design and construction (taken limitation of geotechnical aspects into account).• Prevent of unnecessary delays in construction work• Increasing general awareness of geotechnical risks and possibilities of monitoring.The cost of monitoring compared to the cost of failure and/or the savings that can be achieved play a role in the work of the committee. DFI members benefit from the shared knowledge by the MIC on monitoring and instrumentation within their process of risk management."

Jan 1, 2014

By Kevin P. Gleckler, Steven C. Highfill

"Escalators to access platforms for the Second Avenue Subway Station at 72nd Street in Manhattan are to be installed in the basement of an existing 19-Story residential building. The escalators, which extend below the existing building foundations, require excavation of an inclined rock cavern up to 80-feet deep. Underpinning of columns within the 19-story building as well as a stone masonry party wall and columns for an adjacent 5-story building was completed prior to excavation of the rock cavern to ensure structural stability.This paper will discuss the analysis and design of the underpinning system, the installation and load transfer procedures and the cavern excavation immediately below. The underpinning system was subject to very strict deformation limits and to electronic monitoring prior to and throughout the load transfer and construction process. Key details such as the load transfer mechanism between the reinforced concrete column and the temporary structural steel underpinning frame will be discussed. The challenging rock excavation process will be described which utilized conventional equipment and pattern drilling with Damite rock splitting mortar.INTRODUCTIONPhase 1 of the Second Avenue Subway is being built by MTA Capital Construction (MTACC) to improve subway service on the east side of Manhattan. Entrance 1 for the 72nd Street Station of the Second Avenue Subway is located on the east side of 2nd Avenue at the corner of E 69th Street in New York City. Access to the station mezzanine, approximately 80-feet below grade, is designed to be routed through the basement of an existing 19-story residential building. From the sidewalk, stairs and escalators within the width of sidewalk connect the riding public to a basement level mezzanine, which turns into the building at roughly 16 feet below grade (Fig. 1). Riders then connect to three long escalators to arrive at the station mezzanine. The escalators are to be installed within an inclined and arched cast-in-place (CIP) concrete lined rock cavern (Fig. 2). Construction of both the entrance into the basement and the escalator cavern require the transfer of columns within the 19-story building. Excavation of the escalator cavern also impacts the foundation support for columns and a load bearing party wall for the 5-story residential building immediately to the north. Two stages of load transfer were used at each location. The Stage 1 transfer used a temporary underpinning system to unload the current structure which allowed for construction of the permanent transfer girders. Stage 2 transferred the load from the temporary system to the permanent transfer girders."

Jan 1, 2016

By Zaw Zaw Aye, Sereyroath Chea, Nutthapon Thasnanipan, Thayanan Boonyarak

"As there are only limited numbers of bored pile constructed in sandstone and siltstone in Thailand, load transfer and settlement behavior of a pile in these rocks are still not fully understood. Major factors which influence the performance of the pile in the sedimentary rock should be systematically investigated. The objective of this paper is to analyze load distribution and load-settlement behavior of bored pile in sedimentary rock. Interpreted data was obtained from instrumented load testing results of large-diameter bored piles. These piles were drilled in aeolian soil and socketed in sandstone or siltstone, having socketed length varying from 1 to 3 times the pile diameter. Factors that influenced pile settlement behavior, consisting of rock type at the pile base, socket length, at-rest earth pressure and rock conditions, were analyzed. For interpretation of results, analytical solutions were used to estimate load bearing capacity and calculate settlement of each pile. According to test results of mobilized unit skin friction in siltstone, relationship of 0.1 – 0.3 square root of the unconfined compressive strength of rock appears to reasonably capture the measured shaft friction. Note that shaft movement in siltstone layer was not fully mobilized as maximum pile head settlement was still less that 1% of the pile diameter.INTRODUCTIONExtensive research of bored pile construction in soft soil in Thailand and Myanmar (Boonyarak et al., 2016; Aye et al., 2015) has been carried out. However, behavior of bored pile in weak rocks such as sandstone and siltstone is still not fully understood. Unit skin friction and unit end bearing of piles in these weak rock were reported by Horvath et al. (1983) and Pells and Turner (1980), respectively. Further research is still required to minimize variation in data presented in their study.This paper presents interpretation of load testing results of instrumented piles. These piles were excavated in aeolian deposit in the Northeast Thailand. Some piles were socketed in sandstone or siltstone. Analysis results of load-settlement, shaft shortening, pile settlement estimation, factor for calculating shaft friction and end bearing are reported. Discussion and explanation of pile behavior in sandstone and siltstone is provided.BRIEF INFORMATION OF THE PROJECTProject locationsThe construction sites are located in Khon Kaen and Nakhorn Ratchasima Provinces in the Northeast Thailand. Bored piles in this project were designed for supporting elevated structures for railways, overpasses and U-turn bridges for vehicles. These overpasses and U-turn bridges are distributed along the existing railways with the distance of about 180 km."

Jan 1, 1900

By Jason Herron, Joseph Brown

The common couplings for joining sections of helical piles with an outside diameter of 6.625 inches and 8.625 inches are square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. Each coupling type has advantages and disadvantages in efficiency, capacity, installation, and economics of the installed pile. All these coupling types have been used in the helical pile market in North America for various applications and designs. Many of these applications require on-site testing, but test records are not typically shared with the helical pile industry. Due to the lack of information available for square on square and flange to flange couplings, testing was done to compare the efficiency of installation, load to deflection response, and torque to capacity ratios of external pipe sleeve, square on square, and flange to flange couplings. Field installations and tension tests were performed in non-cohesive (sand type) soil near Caseyville, IL and in cohesive (clay type) soil in Centralia, MO. The data collected during these tests included rotations per foot during installation, installation torque, applied pressure, and deflection. The results of this testing are analyzed and discussed within this paper. The results indicate that the square to square coupling is the most efficient of the designs tested, but this conclusion cannot be fully justified without further testing due to the variability in the data gathered and the small number of piles tested. INTRODUCTION A helical pile is typically assumed to be a medium-displacement pile when its outside diameter is between 4.5 inches and 8 inches and a high-displacement pile when its outside diameter is greater than 8 inches. A helical pile designer has multiple options when selecting a coupling type for medium- to high-displacement helical piles. Each type of coupling has advantages and disadvantages and must be analyzed on the bases of efficiency, capacity, installation, and economics of a project. Typical couplings that are chosen by designers include square on square, flange to flange, external pipe sleeve, internal pipe sleeve, and welded joint. A helical pile must transfer axial, lateral, bending moment, and torsional loads, and the coupling must be designed to effectively and efficiently transfer each type of load. During the installation of a helical pile, the rate of penetration and the disturbance of soil layers play a critical role in the efficiency and torque to capacity ratio (Kt) of the pile. It is common for a coupling to protrude beyond the outside diameter of the pipe section being used. This is necessary for the function of certain coupling types and can facilitate the connection of couplings. However, it causes increased soil disturbance and reduce the rate of penetration due to soil bearing against the protruding portion of the coupling. A helical pile designer typically will work to minimize the coupling protrusion and create a pile with optimal installation efficiency but may choose a design with lower installation efficiency if it offers sufficient economic advantage.

Jan 1, 2019

By Helen S. W. Chow, Harry G. Poulos

Most modern buildings involve the construction of a basement, often of several levels, to maximize the floor area ratio. The basement walls are generally designed for excavation retention purposes only, and are infrequently considered as elements which can help to support the structural loads from the superstructure. However, the basement walls can provide substantial stiffness and resistance to structural loads, and may contribute to the overall foundation capacity and stiffness. This paper presents a simplified approach to approximate the overall foundation capacity and stiffness considering the various components of the foundation system, including the foundation piles, the basement floor slab, the basement walls and interaction between each foundation component. The effect of the basement walls in enhancing the foundation stiffness values is examined by reference to the results of finite element analyses which consider a foundation subjected to vertical, horizontal and moment loadings. The approximate approach is found to give results that are adequate for a preliminary assessment of the effects of basement walls on the overall foundation response, without the need for detailed three-dimensional finite element analyses.

Nov 1, 2022

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017

By Melinda J. Hummel, Zachary T. Smith, Nathaniel Witter, Nina F. Carney

The revitalization of Pittsburgh’s historic Strip District has led to the redevelopment of existing properties and the development of new properties. At one time, the Strip was home to wholesale market products. Now, the historical warehouse buildings are being converted to multi-use residential and commercial properties. One such property, 1600 Smallman Street, consisted of 1 to 6-story connected buildings that housed night clubs, retail shops, and office space. The lower story portion of the building, on the southwest side of the property, was torn down to make room for a new 5-story- parking garage with street level retail space. The remaining 6-story-building, on the northeast, was gutted to be renovated into high-end condominiums, keeping the exterior historical building facade.

By Tony P. Suckling

This paper describes an investigation into the bleeding behaviour of bentonite slurry observed on a trial diaphragm wall panel. The bleeding is thought to be due to the bentonite experiencing a chemical reaction leading to settlement of the solids within the fluid, possibly as a self-weight consolidation process. The trial panel was constructed in a busy airport environment where many different chemical products are used for de-icing the aeroplanes, runways, apron areas, vehicle access and pedestrian routes. The relationships between slurry contamination, bleeding, bentonite hydration time and filter loss behaviour were examined as no relevant published literature could be found. The results show that the amount of bleed strongly depends on both the degree of contamination and the hydration time. It is concluded that bentonite fluids should be allowed to sit in the storage tank for at least 24 hours after mixing, and that the filter loss test is a quick and effective method to determine the potential for bleeding of contaminated slurries.

Jan 1, 2011

By Kevin Green, Iván Contreras, Aaron Grosser, Jon Ausdemore, Rachel Leier, Amr Ragy

"Construction of a new tailings dam was required to increase tailings storage capacity at a trona mine near Green River, Wyoming. The new dam was founded on overburden soils underlain by both fractured and competent bedrock. The stored tailings and water had high salt content, resulting in salty seepage water. To reduce the impact of the salty water on groundwater and the Green River, the design of the new tailings dam included a 257,260 SF (23,900 m2) seepage cutoff extending into competent rock.An extensive subsurface characterization was performed prior to completing the design and suitable seepage cutoff methods were evaluated. The approach selected was a full replacement panel using hydromill and clamshell for construction and self-hardening slurry (SHS) for the wall material. Laboratory testing was performed and ongoing monitoring has continued to evaluate the hydraulic conductivity and seepage cutoff performance in the briny environment.The paper includes project background, the collaborative approach and outcomes of the QA/QC program, and the monitoring results for the seepage cutoff wall.PROJECT BACKGROUNDCiner Wyoming, LLC (formerly OCI Wyoming, LLC) owns and operates the Big Island Mine facility near Green River, Wyoming. This underground trona mine has produced soda ash since 1962. The Greater Green River Basin covers much of southwestern Wyoming and extends into northeastern Utah and northwestern Colorado. The Ciner facility is located in the Green River Basin, which is part of the Wyoming Basin physiographic province. The Green River runs to the west and the south of the Ciner facility.Beginning in the early 1990s, Ciner primarily disposed tailings underground in mined-out panels. However, in recent years, underground storage has become limited and some disposal has transitioned to the ground surface. Long-term planning revealed a need to expand Ciner’s surface tailings disposal capabilities. Pond 2, a previously permitted disposal area, was identified as the most viable location for a storage facility. The Pond 2 site is directly north of the Ciner plant facilities, northwest of the active Upper Delta tailings storage facility, and northeast of the Green River (Fig 1)."

Jan 1, 2016

By Athena C. Denivo, Pablo V. Lopez, Michael McMaster, Sissy Nikolaou, Alfred H. Brand

"The paper presents the history of development of the United States Tennis Association (USTA) site, focusing on geotechnical, geoseismic, and foundation engineering challenges associated with it. The site is located at the Flushing Meadows Corona Park area of Queens, New York. Now home to the Billie Jean King National Tennis Center (BJKNTC), the site used to be a biologically rich, tidal salt marsh that extended south from Flushing Bay and overlaid an ancient buried valley. In early 20th century, Brooklyn Ash Co. was contracted to fill the marshland with cinders and furnace ashes. F. Scott Fitzgerald describes the “Valley of Ashes” as “a fantastic farm where ashes grow like wheat into ridges and hills and grotesque gardens; where ashes take the forms of houses and chimneys and rising smoke, and finally, with a transcendent effort, of ash-gray men who move dimly and already crumbling through the powdery air.” In 1939 the site was leveled and filled to host the World’s Fair and refilled again for the 1964 World’s Fair.The USTA moved to the site in 1978 and in mid-1990’s constructed the 23,000-seat Arthur Ashe Stadium (AAS). Currently, USTA has a Strategic Vision Plan venue with several interconnected construction projects including buildings, infrastructure upgrades and improvements to site circulation. In addition to a historical walkthrough, the authors will discuss technical challenges of supporting these developments through layers of fill, thick organic silty plastic clays and regional varved soils with bedrock found 300 to 400 feet deep. The subsurface is not only a weak foundation medium, but is susceptible to large amplification of seismic waves propagating from the bedrock during earthquakes. The developments are usually founded on project-specific pile foundations that carry static loads in deeper layers and accommodate lateral demands and performance objectives. Engineering innovations from the most recent development, the roof structure over AAS, will be discussed."

Jan 1, 2016

By Dave P. DeClerck

Hardman Construction was faced with the challenge of completing a large earth retention project on a constricted downtown Detroit site, while maintaining a safe and productive worksite. To do so, new technologies using robotic equipment was instituted. HISTORY The historic J.L. Hudson Building (Hudson’s) in Detroit, Michigan was the premier retailer in the city’s downtown district from the 1890s through the 1960s. The massive flagship store sat at 1206 Woodward Avenue, one of the busiest streets in the Detroit area. Hudson’s broke ground in 1891 and would go through twelve renovations and expansions. The last renovations took place in 1946, which gave the building the title of being the largest department store in the world at the time. It spanned an entire city block and boasted 2.2 million square feet of retail space. By the 1970s, Detroit was in an economic downturn. The Hudson’s department store finally closed its doors in 1983. Besides a few working offices, the building sat vacant. The building was unique in that it had four levels underground, offices, mechanical areas, and equipment storage. Following years of neglect, the Hudson’s building was seized by the state and transferred into the hands of the city. The city had it demolished in 1998, (shown in Fig. 1) to construct a new, four- level underground parking garage as well as a potential future above-grade development (Sewlck, 2017). The building was imploded in one of the largest implosions of that time. The building rubble filled the underground rooms and helped to stabilize the exterior concrete walls and keep them from collapsing.

Jan 1, 2019

By Heman Manchanda, Jyoti Agarwal

Several infrastructure projects are under construction in India; many of them involves construction of deep foundations like reinforced concrete and steel piles to support super structures. As most of the piles being constructed in India are reinforced concrete bored piles, there are always uncertainties relating to the quality of construction, and in this case non-destructive methods to ascertain quality of piles becomes very crucial to success of any project. Non-destructive pile testing is becoming more and more popular with growing technologies wherein geophysical techniques and wave propagation theories are being used for pile quality and length analysis. Low-strain pulse echo method and cross-hole sonic logging testing are two pile integrity testing techniques being currently practiced in India which are cost effective and provides reliable near accurate results if analyzed properly. Paper presents current practices being adopted in India for conducting these two tests, highlighting the critical site considerations and analysis techniques. The paper also discusses various execution and interpretation challenges faced by practicing engineers and recommends a way forward.

Sep 1, 2022

By Travis Coleman, Elvis Ishimwe

Currently, more than 400 drilled shafts have been constructed by various contractors at the I-90/94 and I-290 Jane Byrne (Circle) Interchange, located near downtown Chicago, Illinois. Cross-Hole Sonic Logging (CSL) and Thermal Integrity Profiling (TIP) tests were performed to evaluate the integrity and concrete quality of the drilled shafts installed at this project. For Phase I of the project the shafts were tested using CSL methods, and the shaft integrity was identified by analyzing the First Arrival Time (FAT) and the signal strength (energy) measurements. For the major portion of Phase II, the Illinois Department of Transportation (IDOT) accepted TIP testing as a substitute for CSL at the request of the contractors. The CSL testing results indicated 54 percent of the tested shafts had anomalies, and 78 percent of these anomalies were located within the lower three diameters of the shafts. To date, TIP testing results indicated the shaft integrity was as expected and acceptable for the all 34 tested shafts. A review of the testing results and a discussion of the detected anomalies are presented. In addition, a comparison of both TIP and CSL measurements is presented in this paper.

By Konstantin G. Ashkinadze

The paper considers performance of piles supporting transient pipe anchors in heavy industrial pipelines. Events such as pump trips or opening and closing of large valves produce short-term dynamic pulses in the pipeline with variable spectral characteristics. Their magnitude is large enough to cause major damage to the pipeline and its anchors, which face horizontal impact loads amounting to hundreds of kN. Design of pile foundations supporting these anchors is often governed by limitation of deflection of the support to prevent overstressing pipeline connections and equipment nozzles. The maximum deflection does not always correspond to the largest load because the stiffness of the soil surrounding the piles heavily depends on the rate of loading. Faster actions encounter stiffer soil response while loads of smaller magnitude applied slowly may be more critical for the deflection time history of the anchor. A typical transient action has both high- and low-frequency harmonics, which makes the response complex. Using load rate-dependent p-y curves published in literature, the paper develops methods of analysis of pile foundations for transient anchors. Pile displacement amplitude – input frequency – natural frequency correlations and time histories of pile response are constructed for typical profiles of transient actions, considering nonlinear soil response to large horizontal loads.

Jan 1, 2016