Search Documents

By Gordon King

The City of Atlanta Water Department required the construction of a two sludge tanks and a wet well at the existing Chattahoochee Water Treatment Plant. Western Summit won a design build contract to build the project and proceeded to evaluate the wet well size options, and construction procedures. The final design required the construction of a 1 million gallon tank. The proximity of the underground tank to adjacent roads and existing plant structures ruled out laying back the excavation. As a result a tied back sheet pile retaining wall was initially proposed.

Jan 1, 2003

By Yeruva Ramanareddy, Sohail Wajid, Ahmed Shaz, K. Bhavani

"CP-06 is an NATM cross passage which connects up-line and down-line metro tunnels near Kilpauk Medical College, Chennai. It lies completely in loose silty sand to dense sand with water table almost touching the ground surface after Chennai floods. Pre-grouting was done before excavation to seal the area and to ensure no-loose pockets. The heading was excavated successfully but while benching excavation huge water ingress started seeping out. Sand also permeated along with water which became unstoppable due to cavity formation and caused the up-line tunnel to sink considerably. A large grouting exercise was carried out with different grout materials and techniques both from the ground surface and inside of tunnel to stop the water ingress and stabilize the tunnel. This paper describes the chronology of events that occurred in the tunnel during CP-06 issue. It elaborates all the different grouting techniques involved in the whole process of the tunnel stabilization. It includes a finite element analysis using Rocscience RS2 9.0 software showing the possible cause of sand incursion with water from the CP invert which lead to the tunnel settlement. This paper also describes the after effects and the lesson learnt from the whole incident.INTRODUCTIONConstruction of Metro Rails has become the latest alternative to cope up with the transportation demand of the growing urban cities population. L&T SUCG JV constructed Chennai Rail Metro Phase II Contract UAA-04 which included design and construction of approximately 4 km of route length of underground mass transit railway including 3 underground stations. This package also includes 12 cross passages which are NATM tunnels connecting upline and down-line side of TBM tunnel for safe evacuation of passengers in case of emergency. As per NFPA guidelines, this is a mandatory structure and there should be atleast one cross passage in 244m tunnel length.CP-06 is a cross passage connecting upline and downline tunnel between Pachiyappa College Station and KMC Station, in Chennai Metro. During the construction of CP-06, heavy water seepage of around 450 liters per minute was encountered during second round of benching excavation after full heading was excavated. An inflow of around 12-15 cum of sand and silt was also observed inside the tunnel along with the seepage water, which created piping inside the TBM tunnel causing it to settle continuously with time. A huge effort was made to stop the water ingress along with loose sand which was causing the running tunnel to settle, involving all possible grouting methods and temporary support installation."

Jan 1, 2017

By L. F. Miao

Studies were carried out to investigate the ultimate soil pressure acting on pile(s) undergoing lateral soil movement in soft clay. A special apparatus has been designed to apply a uniform rectangular profile of lateral soil movement on the rigid pile(s) with pinned head and tip conditions to obtain the ultimate soil pressure. The piles were 16 mm (5/8 in) in diameter. For the pile group tests, the behavior of different number of piles (2, 3, 4, 6 and 9), pile arrangements and center-to-center spacings (3 and 6 diameters) were investigated. In this paper, the group factors of 11 combinations of number of piles, pile arrangements and pile spacings are presented. The group factors are given for individual piles in a pile group as well as for the entire group. Generally, the group factors of individual piles in a group varied significantly according to pile spacing in both directions, and pile arrangement; the group factor of the whole group reduced with an increasing number of piles, and increased with increasing pile spacing. For a pile group with the same number of piles but different pile arrangement, no significant difference was found in the group factors for the entire group.

Jan 1, 2008

By Gordon King

The site of the First Quality Tissue plant is located on a previous paper production facility in Lock Haven, Pennsylvania. The new development, which included the construction of a tissue machine building, baled building, converting building, various storage buildings and an electrical switchgear building, required the use of deep foundation systems to transfer loads below compressible fill and alluvial soils. Loading details provided by Jacobs Engineering, the project structural engineer, detailed braced steel frame buildings with typical column loads ranging from 75 to 150 kips and slab live loads of 250 to 300 psf. As an exception to this, however, the tissue machine and stock preparation building, which had a roof height ranging up to 85 feet, had column loads ranging up to 800 kips in addition to high dynamic loads. The First Tissue plant is located in a river valley in the hills of Western Pennsylvania. To evaluate the proposed site conditions and to formulate recommendations for the structure foundations, a geotechnical study was performed by the owner. Approximately 30 borings were advanced to bedrock, with wire-line coring performed in the tissue machine building. The borings disclosed a soil profile comprising of the following:

Jan 1, 2004

By Li Keqiang

Among the pile foundations of the 156 tall buildings over 18 storeys in Shenzhen, 86. 5% of them are constructed by slurry drilled piles, bored piles and excavated piles (hand-dug caissons). Based on the experiences of the engineering practices, the paper points out that the main quality problems of pile foundations in Shenzhen are: insufficient bearing capacity of single pile; poor concrete quality of pile; damage of the precast pile; pile tip not reaching the required bearing stratum and the thickness of bored/drilled sediment exceeding the specified. etc. The quality inspection methods that have been used include: check of construction records and excavating; static loading test; core sampling test; non-destructive test, etc. Treatments of quality problems used in Shenzhen are also introduced in this paper.

Jan 1, 1991

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By Alexander Filotti, Stanley Merjan

"Abstract. The paper shows the benefits and accomplishments of this relatively new but established product on the pile foundations market in the United States. The first part of the paper describes general aspects of the design, construction, and geotechnical capacity (designed and in situ) of Tapertube piles. The qualities resulting from the design and manufacturing of the Tapertube pile will be presented first.The second part of the paper describes the installation of Tapertube piles for an addition to Terminal One at JFK International Airport and The Edge development. A carbon print analysis for both projects is developed using the EFFC-DFI carbon print calculator. For the JFK project the benefits of using BIM in redesigning the project for Tapertube piles are explored.General description.The tapertube pile consists of a tapered tubular bottom section attached to a conventional pipe extension. The 50 ksi steel for the taper is mechanically folded into a polygonal cross-section (usually 12-sided) with a longitudinal welded seam. The tapers are fabricated in many sizes with bottom diameters varying from 8 to 14 inches, top diameters from 12 to 20 inches, lengths from 10 to 35 feet, and steel thicknesses from 3/16 to 1/2 inch. A conical steel shoe or a flat plate is welded to the bottom of the taper and the top of the taper is circularized to match the outside diameter of the pipe extension. The inclination of the tapers is generally between 1.5% and 2.5%.The pipe extension is fully butt welded to the taper and has the necessary length for the pile to develop the requisite capacity. Concrete fill for the piles is generally 4,000 p.s.i. or more. Typically the piles are shopassembled and shipped to jobsites in lengths to 80 feet."

Jan 1, 2014

By Peter J. Nicholson

Since the reintroduction of soil mixing to the United States over 10 years ago, the work installed by soil mixing technology has grown dramatically. From an annual turnover of less than ten million dollars per year the volume of soil mixing put in place has grown to an estimated $40 million per year in the year 2000. The majority of work done to date has involved walls, either for excavation support, permanent retaining structures or hydraulic cut-off walls. The other major use for soil mixing has been for mass stabilization of soils whether for isolation of contaminants or for retaining structures. This paper will discuss the uses of and costs of typical soil mix structures. BACKGROUND Soil mixing is defined as the in-situ combining of reagents, typically cement, with native soils, the purpose being to modify or improve the ground. This history of soil mixing covers only the use of cement slurry, aggregated with soil in-situ by mechanical mixing methods only. Soil mixing by use of high-pressure hydraulic means, also known as Jet Grouting, will not be discussed. In addition this will not cover ex-situ (above ground) mixing, or mixing dry reagents with soil. Only mixing applications for building, civil and heavy construction applications will be discussed, with only passing reference made to uses of soil mixing for environmental remediation work.

Jan 1, 2001

By Robert E. Fosse

Driven 14-inch-square concrete piles were used as the foundations of Genentech Hall at the new University of California, San Francisco Mission Bay Campus. The five-story, steel eccentrically-braced frame building is currently under construction at a 43-acre property located in a former large shallow marshy inlet from San Francisco Bay. The piles were driven through 10 to 25 feet of fill and 20 to 60 feet of soft compressible Bay Mud into an underlying dense sand layer. Pile design capacities were developed for traditional allowable stress design, load factor and resistance design, and ultimate design criteria. The ultimate level capacities were for checks of loads occurring when the links in the eccentrically-braced frame yield during an earthquake. A load test program was performed to confirm pile design recommendations. Two test pile locations were selected for compression, tension, and lateral load tests to evaluate pile capacity and pile/soil stiffness under long-term, short-term and rapid loading conditions. Maximum test loads were 1000 kips downward, 350 kips uplift and 50 kips lateral. Foundation construction began by driving 34 indicator piles with a Delmag D46-32 diesel hammer of 113 foot-kips maximum rated energy. All indicator piles were monitored during initial driving using the Pile Driving Analyzer. Restrike data, obtained several days after initial driving, indicated significant pile-soil setup and typical pile capacity increases from 750 to 1000 kips. The majority of the 1242 production piles were then driven to acceptance criteria of 75 blows per foot and a minimum embedment of 10 feet into the dense sand bearing layer. Piles driven to full length without achieving the blowcount criteria were evaluated on a case-by-case basis. Acceptance of these piles was established by evaluating restrike data.

Jan 1, 2002

By Fawad S. Niazi

Ever since the use of the cone penetration test (CPT) in geotechnical practice, attempts have been made to correlate CPT parameters with pile capacity components of unit end bearing (qb) and unit shaft resistance (fp), thus deriving multiple CPT-based pile design methods. These methods focus on "capacity" only without consideration to complete axial pile load-displacement (Q-w) response. Estimated capacities from these methods also exhibit considerable scatter without any consensus on their consistency. In addition, load-displacement curves obtained from axial load tests on highly expensive and extensively instrumented piles can exhibit different shapes. Nevertheless, a single value from the curve so obtained dictates the design capacity. Currently, there are at least 42 different criteria defining capacity with considerable variation in the values obtained thereof. The Randolph elastic solution, which provides a framework for analytical evaluation of pile load-displacement response, requires the profiles of soil stiffness. The fundamental soil stiffness defined by the small-strain shear modulus (Gmax) can be obtained from shear wave velocity (Vs) readings via seismic piezocone tests (SCPTu). The secant stiffness (G), which softens from Gmax corresponding to operational load levels, can be obtained by generating stiffness reduction curves from back analysis of load tests. Then, using appropriate G values, the Q-w curve can be defined for conditions similar to the database from the pseudo strain (w/d). Thus, a complete framework for optimal integration of SCPTu data, Randolph elastic solution and back-analysis of field operational stiffness can be established for complete axial pile foundation analysis.

Jan 1, 2011

By Nathan W. Iverson, David S. Graham, Paul J. Axtell

"The Highway 53 relocation project in Virginia, Minnesota, involves construction of a very tall bridge across a currently inactive iron ore mine pit. The inactive pit is partially flooded and serves as the community’s drinking water source. The 1,132-ft long new bridge is a three-span, plate girder structure. Two intermediate, approximately 200-ft tall piers are located within the pit.The foundations for the two piers consist of groups of 30-in diameter piles which, despite the contradiction in terms, are essentially very large micropiles. Extremely challenging and highly variable subsurface conditions exist at the site, ranging from uncontrolled iron ore mine waste fill to some of the hardest rock on earth that can also be highly fractured and abrasive. Despite the conditions, large diameter (30-in) micropile foundations up to 175 ft deep were successfully installed using down-the-hole hammer methods and full-length permanent casing under an extremely aggressive construction schedule.Full-scale foundation load testing using the Statnamic rapid loading method was also conducted in support of the design and construction but under a separate pre-design phase contract. This paper describes the unique aspects of this foundation project, including design, construction, and load testing of the large micropiles.INTRODUCTION AND BACKGROUNDIn 1960, a segment of Trunk Highway 53 (TH-53) in Virginia, Minnesota, was built on land owned by iron ore mining interests. As part of the roadway easement agreement, Minnesota Department of Transportation (MnDOT) was to be given notice three years prior to termination of the easement. In 2010, MnDOT received notice that the mining interests wished to access the ore. Through negotiations in 2010, MnDOT and the mining interests agreed to a 2017 date for abandoning the existing section of roadway. During this period, MnDOT needed to procure project funding, satisfy environmental permitting requirements, and acquire new right-of-way to permanently reroute TH-53 and keep it open to traffic. This was no easy task due to the existing mine pits surrounding the area.The E-2 alignment option shown in Fig. 1 was ultimately selected for the rerouted highway in 2014. The new highway segment includes a three-span bridge across the currently inactive Rouchleau Mine Pit. The inactive pit is partially flooded and serves as Virginia’s drinking water source. The 1,132- ft long new bridge is a three-span, plate girder bridge. Two intermediate approximately 200-ft tall piers are located within the pit. Fig. 2 is a conceptual rendering of the bridge."

Jan 1, 2017

By Graeme McWhirter

This paper discusses the Installation of a Vibwall for the Cardiff Bay Barrage Project Wales, UK, by Kvaerner Cementation Foundations. Only the second use of the technique in the UK the wall was successfully placed to a depth in excess of 20 metres, in unique and challenging conditions. The installation of the Vibwall was a technical success, but not a financial one. The use of the technique was at its "limits" and this paper recommends some of the controls essential in the carrying out of such work in the future.

Jan 1, 2000

By Scott White, Pishun Tantivangphaisal, Andrew Bell, Chris Barker

There has been considerable advancement in recent years in the tools, both software and hardware, available to allow efficient digitalization of site records during the construction of geotechnical works. Whilst these tools have excelled at replacing handwritten records, the ability to use digital records to validate design and construction requirements in real time or even within reasonable timescales has generally been limited to the development of bespoke ‘prototype’ project specific solutions. This paper describes the development and implementation of an industry standard design schedule and the benefits of the broad adoption of a single database schema for data recorded on geotechnical sites. The former has brought significant improvements and automation of the design process, whilst the latter has enabled the validation of the constructed works against design intent in almost real time. Further details of the standardized design schedule, already publicly available in the UK through the FPS, examples and lessons learnt from implementing digital site record systems on live projects are presented herein. The utilization of cloud computing technology and complex algorithms linking plant/rig instrumentation with design data can further automate construction sites using IoT (Internet of Things) best practices. The authors will share their experience of the recent deployment of a digitalized design-to-construction record system, give recommendations for future development and a call for an industry wide drive to finalize and adopt the AGS Piling data schema.

May 1, 2022

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999

By Jeffrey R. Hill

To extend the life of the Merchants Railroad Bridge crossing the Mississippi River in St. Louis, MO, the owner implemented a rehabilitation and reconstruction project. The Merchants Bridge provides a key link in the transcontinental railroad system. The bridge is of local importance to the Terminal Railroad Association ? providing a link between St Louis and a rail switching yard in Venice, IL. The intent of the bridge rehabilitation is to keep the Merchants Bridge in service, even though the bridge was originally constructed in the 1890?s. The project involved replacing the East and West approach deck truss spans with new deck girder spans. The rehabilitation program required construction of new concrete piers to support the new spans. In order to reduce the track down time to two, ten day single track shutdowns, the specifications required that all foundation and substructure work be completed while leaving the existing spans in place. The preliminary bridge design specified rock-socketed drilled shaft foundations. Drilled shafts proved to be challenging due to working from beneath the existing bridge, a high water table, utilities, a flood wall, and existing rail way lines. The micropile alternative was technically appropriate given the access limitations, shortened the foundation rehabilitation schedule by several weeks, and realized a significant cost savings to the Owner.

Jan 1, 2006

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel&apos;s displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By Heinz Brandl

Box-shaped pile and diaphragm wall foundations have proved suitable for transferring heavy loads of bridges, power plants, tanks, towers or other buildings in a concentrated form into the ground. The bearing-deformation behaviour and the earthquake resistance of such "box-foundations" are superior to those of conventional pile groups. The reason lies in the reduction of lateral soil displacement and in the composite effect between concrete elements and the enclosed soil. The paper describes results of comprehensive model tests and in situ measurements, theoretical aspects and case histories.

Jan 1, 2002

By Paolo Cavalcoli, Marco Ziller

"ABSTRACT: In the year 2010 the State of Denmark together with the Municipality of Copenhagen, launched a very important and complex Project : the complete construction of a new double Subway Line :the CITYRINGEN.Copenhagen is the capital with a metropolitan population of 1,9 million.This line is like a ring placed in the very town center which includes all the most historical and monumental buildings and churches, with a total length of 17 km, and the presence of 17 stations plus 4 service shafts.The buildings have been built in the last centuries in an area where the groundwater is near to the surface and there are lakes and channels: the techniques adopted were advanced for those times, but limited as far as regards settlements and resistance to horizontal movements.The soil consists in 2 main groups.1.Upper sediments of the glacial ages : thickness total = 5-20 m composed by clay- silt-sand-gravelcobbles- granite boulders and flint in blocs and in layers : frequency and size of these obstacles wherenot determined.2.Limestone layers : 2a. upper limestone : highly fractured ,highly permeable2b.Itermediate limestone : less fractured, medium permeability.2c. Lower limestone : almost not fractured, low permeability.2d Bryozoan limestone : composed by fossils with microscopic dimensionsIn all the limestone formations there are important layers of flint , having thickness variable up to 3 m and important extensions. Water : in a part of the areas of the Cityringen the water is drinkable and utilized in the public waternet.Pollution: there are polluted zones due to previous industrial activities. Benzene areas have been identified, and for those areas special protections against pollution have been implemented.METROSELSKABET ,the public owner of the Cityringen,has set as priority to operate for the construction of the Cityringen the full protection of the environment and the respect of all the stakeholders :Very strong limits for the exhausted gas emissions have been introduced, by far stronger than those applied from the State of Denmark, very strong limits for the acceptable noise emission. And last but not least very important safety measures and procedure to avoid any accident on site."

Jan 1, 2014

By John F. MacDonald

From 19BS thru the present, Guy F. Atkinson Construction Company has been involved in several transportation construction projects in the Seattle area. Two of these contracts, the Mt. Baker Ridge Tunnel, and The Seattle Bus Tunnel, had unique foundation features. MT. BAKER RIDGE TUNNEL ACCESS PITS The Mt. Baker Ridge Tunnel is part of the general upgrading of the I-90 freeway between I-405 and I-5 (see Fig. 1). It is located on the western shore of Lake Washington and consists of a 1300 foot long large diameter tunnel thru Mt. Baker Ridge. The ridge consists of over consolidated silts and clays overlain by a loose to medium dense silty fine sand. The water table is perched in this upper layer of material. The clays of Seattle have a history of being very sensitive to excavation. The hills are marginally stable and numerous landslides have occurred recently in the area of the tunnel. [ ]

Jan 1, 1990

By Michael McVay

The use of augered cast-in-place piles has seen tremendous growth under commerical structures in the past twenty years. Problems with vibration, soil densification and/or heave associated with driven piles do not occur with properly installed augered piles. Augered cast-in-place piles were originally constructed (1950s) with diameters of .31 m (12 in.) and lengths up to 6.1 m (20 ft); however with the advent of better drilling equipment, diameters varying from .41m(16 in.)to .61 m (24 in.) and typical depths ranging from 18.3 m (60 ft) to 24.4 m (80 ft) are achievable. Reinforcement may vary from a single high strength rebar (Grade 60) at the top of the pile to a continuous steel cage depending on loading (compression, tension-uplift, and lateral). Typical axial design loads (compression) for a single augered cast-in-place pile are in the 445 kN (50 tons) to 890 kN (100 tons) range.

Jan 1, 1997