Search Documents

By Garland Likins

High strain PDA testing has become common for verification of capacity of both driven and bored piles. It is equally applicable to Augered-Cast-in-Place (ACIP) Piles. It also evaluates other aspects of the installation such as integrity. The benefit of high strain dynamic test results for the relatively low cost of the tests compared to conventional static testing has resulted in widespread use. The method is described and specific procedures for testing ACIP piles are outlined. Example results demonstrate the application.

Jan 1, 2000

By Roderic A. Ellman

The new Woodrow Wilson Bridge (WWB) will replace the existing bridge over the Potomac River to connect Alexandria, Virginia to Prince Georges County, Maryland. The new WWB will extend approximately 1.1 miles across the river, with a 367-ft long bascule span in the main river channel where the water depth is about 36 ft. The bridge is primarily comprised of fixed spans in relatively shallow water and a bascule span over the navigation channel. The subsurface soil profile was quite variable along the bridge alignment. In Virginia, there was fill over soft Alluvial deposits underlain by dense Terrace deposits, as well as remnant foundations from a former ship yard. At the bascule span, there was up to 50 ft of a soft organic silty clay layer underlain by a deep deposit of stiff Cretaceous clay. Along the Maryland approach, there were Alluvial deposits over dense Terrace deposits over stiff Cretaceous clays and dense Cretaceous sands. The variation in subsurface conditions led to the selection of alternative deep foundations that suited the specific conditions and were based on the design phase testing program, from which ultimate design capacities were determined. During construction, there were instances of unexpected pile performance, notably different than that experienced during the design phase testing, requiring changes to the contract installation criteria and re-design. This paper will present the types of deep foundations used for the project, the performance criteria assumed during the design, the measured performance and difficulties encountered during construction, and the resulting remedial actions, i.e., changes to contract installation criteria and/or re-design due to the unanticipated field conditions.

Jan 1, 2009

By Jack Hayes

The design and construction of deep foundations involve many uncertainties. For the designer there are uncertainties regarding soil and ground water variability, regarding sampling and lab testing, regarding analytical techniques and regarding construction technique. The latter being the uncertainty over which the engineer has least control and which may have the greatest impact on capacity. Foundations with a high design factor of uncertainty can be very costly. Foundations designed with a high factor of uncertainty may have a low factor of safety, which can be even more costly.

Jan 1, 2000

By Lucian Bogdan

On many occasions during construction and service life of the structure, it is crucial to know the load in post tensioning tendons and anchors. Although there are many methods to measure the tendon force, most of them are cumbersome, expensive and the accuracy differs depending on the method used Dyna Force sensor uses the Elasto-magnetic technology (EM) and non destructive testing (NDT) to direct measure stress level in prestressed strands or bars installed on ground anchors or post tensioning tendons. Dyna Force sensor can be used to rapidly read the change in load during proof and performance tests and compare with the pressure gauge and during the life on the anchor to monitor existing lock-off load. It can be used also to determine the load along the bonded length of the anchor allowing the contractor to increase or decrease this length. The paper presents Dyna Force operating principle and some applications. In conclusion, the Elasto magnetic technology applied through Dyna Force is a new and easy to use approach to monitor anchor load during proof test and service life of the structure.

Jan 1, 2009

By Michael T. Lambert

The purpose of the this paper is to demonstrate the benefits of using additional instrumentation during load tests of auger-cast-in-place piles. Traditionally, only load and butt displacement are determined during load tests. The results from and methods used to instrument 15 auger-cast-in-place (ACEP) piles as part of six projects are included herein. By instrumenting the piles, the distribution of load along the pile length and load transfer can be determined, allowing the pile capacity to be adjusted or the length/diameter of the pile to be adjusted for the a given required load. The majority of the piles tested were designed as end bearing piles on either shale or limestone bedrock. No discussion of Geotechnical Instrumentation can be started without acknowledgement of the "Red Book." The actual title of the book is Geotechnical Instrumentation for Monitoring Field Performance, by Mr. John Dunnicliff, John Wiley and Sons, 1993. Anyone undertaking an instrumentation program should thoroughly review the Red Book, paying particular attention to Chapters 3 and 4. Instrumentation should not be done just because it can be done. There must be an unanswered question or questions that can be answered with measured data before instrumentation should be considered.

Jan 1, 2000

By Matthew Janes

The RC Harris Filtration Plant, which treats the majority of the fresh water for over 2.5 million Torontonians, is a Canadian Architectural Heritage site demonstrating a classic example of Art Deco Architecture. The facility is undergoing an expansion to install an underground sludge treatment capability. Perched atop a bluff on the North shore of Lake Ontario the structure enjoys a commanding presence on the Lake Ontario shoreline. A series of underground tanks were proposed for the hillside below the structure, which when covered would preserve the building?s architectural presence. However, the plan required two, stepped excavations 12 m and 10m deep into compact, wet sands over stiff clays and clayey silts. Concerns regarding the original structure influenced designers to set the lateral deflection limit for the front footing of the existing structure at 4 mm, (0.03% excavation depth). The design-build team indicated at the time of tender that the movement criteria was unattainable using the tender design. Analysis indicated installation effects and overall elastic movement of the soil mass beneath the building would result in movements of 7 to 9 mm at the structure. Through extensive FLAC analysis and a novel construction geometry the design-build team crafted an alternative that produced significant savings over the original concept. Based upon the analysis the design-build team negotiated a new deflection criteria dictating a maximum of 2.0 mm of movement across the critical expansion joint between the Filter Building front footing and the tank slab beyond. The contractor invested in additional pre tender soils investigation to support the refined design process. The FLAC analyses indicated the Filter Building movements would be elastic and distributed up to 50 m back beneath the front footing of the structure. An extensive precision monitoring program proved construction related movements of 6 to 10 mm horizontal at the front footing. Extensometers placed at two locations over the critical interior tank expansion joint showed no measurable movements. The overall monitoring program, including inclinometers, tilt meters, tie back extensometers (smart cables) and tie back load cells indicated a good match between recorded movements and loads and those predicted by FLAC Analysis.

Jan 1, 2006

By Cem Altuntas

This paper is the second in a series of two describing the design and construction of a foundation for a major high-rise real estate development on the west side of Manhattan, N.Y. The foundation members consist of large-diameter rock-socketed caissons, driven closed-end steel pipe piles bearing on rock, and a secant-pile retaining wall surrounding the entire site. This paper focuses on the Osterberg cell (O-Cell) load test completed for determining the allowable side-shear resistance between the concrete and the sides of the rock socket. Different qualities of mica schist bedrock, demonstrated by the penetration of rock with the soil auger or drill casing, were encountered. Accordingly, an additional subsurface investigation consisting of test borings at each caisson location was completed. Unconfined compressive strength tests were performed on representative rock samples. The ?soft? mica schist was observed to have vertical foliations and high mica content. For the first time in Manhattan, an O-Cell load test was performed to determine the allowable side shear resistance for both the soft and hard mica schist bedrock. The side shear resistance obtained from the O-Cell load test is compared with the side shear resistance allowed by the New York City Building Code and empirical correlations using unconfined compressive strength values for rock. The rock socket design for the caissons was refined based on the O-Cell load test results.

Jan 1, 2008

By Schmitz Stefan, Stephan Jee-Sun

"Due to the reunion of Western and Eastern Germany in the late 80’s, a multitude of infrastructure projects had to be executed. A good portion of these projects required improvement of the motorway system. In the southern region of Leipzig, in the eastern part of Germany, it was required to connect two existing motorways. Parts of the new motorway pass old strip mining areas. These strip mining areas consist of up to 70m thick backfill material. Especially the upper 20m are very inhomogeneous soil material with a very low bearing capacity. In order to increase the bearing capacity, to decrease the differential settlements and to homogenize the soil parameters, soil improvement using sand-gravel columns was required. Bauer Spezialtiefbau GmbH executed the installation of approx. 711,000 linear meters of columns with a length from 5 m to 25 m. For the project, 11 rigs with frame leads up to 40m were used to install the 43,000 columns with a diameter of 0.8m in 27 weeks.1. INTRODUCTION1.1 Site LocationThe construction site is located in the south-eastern part of Germany, in the south west of the city Leipzig.The area to be treated had a size of approx. 500,000 m² to allow the construction of dam/embankments and a highway bridge.1.2 Required WorkIn addition to the general earthworks and the installation of geogrids and fibre mats, a total amount of more than 710,000 linm of Gravel-Sand Columns with different lengths due to the given soil conditions had to be installed:•nos. 4,206 Columns length 5m ? 21,030 linm•nos. 4,581 Columns length 10m ? 45,810 linm•nos. 10,820 Columns length 15m ? 162,300 linm•nos. 19,634 Columns length 20m ? 392,680 linm•nos. 3,574 Columns length 25m ? 89,350 linmFor the installation of the columns Gravel-Sand with the grain size of 0/32mm was used. The total amount of Material was 580,000mt"

Jan 1, 2015

By E. W. Raabe

The paper discusses the increasing role of specialist grouting techniques to form water seals or cut-offs for deep basement construction. Raabe and Toth discuss the various grouting methods available for sealing applications and then concentrate on the use of Soilcrete Jet Grouting, a system particularly well suited to ground water control. The Soilcrete processes, suitable soil types and quality control methods are fully described, particularly with regard to the formation of cut-off walls and sealing slabs to prevent the progress of ground water or leachates. The authors have included case histories detailing their experience on designing and installing Soilcrete seals for various projects in West Germany. These include an underground rail project in Dortmund and a discharge structure for the Alz Canal at Burghausen.

Jan 1, 1989

By Tsuyoshi Honda, Kazuhiro Kaneda, Masayuki Imai, Kazuo Konishi, Kunio Higashinaka

"In recent years, the demand for measures to control liquefaction of existing airport runways and harbor structures has increased. However, from the perspectives of constructability and cost, application of grid-form deep mixing walls to these types of structures requires the formation of wider grid spacing as compared with conventional designs. In this research, we focused on the extent of liquefaction and ground surface settling when grid spacing is made wider than conventional designs. We conducted centrifuge model tests, and confirmed the liquefaction suppression effect when grid-form modifications involving wide grid spacing are adopted under asphalt pavement. The tests were conducted under conditions that included changing the grid spacing and groundwater level. When the groundwater level was high, an increase in water pressure was observed, even within the grid. However, when the groundwater level was low, the increase in water pressure inside the grid was suppressed. We also found that if the generation of water pressure can be suppressed, the amount of settling due to liquefaction can also be controlled.INTRODUCTIONOne construction technique used as a countermeasure to liquefaction is grid-form deep mixing walls. Grid-form deep mixing walls are a construction technique for which improved grid-shaped wall bodies are built into the ground below the surface using a deep mixing method. This construction technique minimizes shear deformation by surrounding liquefied ground with improved wall bodies, thereby preventing liquefaction (Fig.1). With conventional designs, grid-form deep mixing walls determine the grid spacing that can deter liquefaction based on a ratio of the grid spacing L to the improved depth H (ratio = L/H). Ordinarily, designs are implemented with an L/H ratio of 0.8 or less (PWRI, 1999).In recent years, a demand for measures to control liquefaction of existing airport pavement and harbor structures has increased. However, when liquefaction countermeasures are implemented at these types of facilities and structures, the construction work must be implemented while the facilities and structures remain in service. Therefore, temporal and spatial constraints must be considered. In addition, unlike conventional liquefaction countermeasures, performance requirements are such that, even if some degree of liquefaction is allowed, the performance is acceptable as long as the amount of settlement is within a predetermined value. Therefore, if grid-form deep mixing walls are applied to these structures, grid spacing that is wider than conventional standards is desired."

Jan 1, 2015

By Theodore W. Vogelpohl

Augered cast-in-place piles have proven to be effective, adaptable and economical for projects throughout the Ohio River Valley. Specifically, they have been used extensively for high-rise structures, sports stadia and large commercial developments along the Cincinnati, Ohio and Northern Kentucky Riverfront. They have been designed and utilized as relatively short toe resistance piles in bedrock, and intermediate to long toe and shaft resistance piles in granular outwash deposits above the bedrock. They have been designed for large axial compression loads as well as moderate axial tension loads and lateral loads. This paper presents a few load test results that demonstrate the range of capabilities of augered cast-in-place piles in the variable subsurface profile along the Cincinnati, Ohio/Northern Kentucky Riverfront.

Jan 1, 2005

By K. E. Darnell

Drilled pier foundations have long been a favored foundation type for heavily loaded structures. Drilled piers derive their load-bearing capacity from end-bearing, and/or sidewall friction. This type of foundation is used in many geologic settings, including those areas underlain by hard carbonate rock, such as limestones and dolomites. When properly designed and constructed, drilled piers provide high load-carrying capacity in both compression and uplift. However, carbonate rock is often subject to intense differential weathering resulting in the formation of an irregular bedrock surface, sinkholes and caves; consequently, the investigation for, and the design of, drilled pier foundations is often complex. Further, the construction may be difficult and costly. This paper discusses geotechnical investigative procedures which can be employed to develop foundation design criteria and reduce the frequency of changed conditions. Finally, state-of-the-art construction practices and quality control techniques are discussed.

Jan 1, 2010

By William F. Starke

"The Ontario College of Art & Design (OCAD) located in Toronto, Ontario, found itself in dire need of space due to increased enrollment, leading them to embark on a major expansion and redevelopment on campus. The expansion entailed an additional 115,000 sq.ft. (10,700 m2) and a new major structure was required, as well as extensive redevelopment of existing buildings. The new Sharp Centre for Design was designed by acclaimed British Architect Will Alsop, of Alsop Architects, in a joint venture with Toronto-based Robbie/Young + Wright Architects. The OCAD campus is cramped for space and the design selected was a structure built over top of existing structures. The building has been described as resembling a “shoebox in the sky”, supported on raked columns transmitting high lateral forces as well as compression load to the foundations. There are 12 such supports, each supported by an individual caisson. In addition, the project entailed installation of other caissons in the courtyard area with the construction work accomplished under very confined conditions among the existing structures. The remarkable design for the new Ontario College of Arts will surely make it another of Toronto’s architectural landmarks. Several things make this project stand out as a unique deep foundations project.First is the architectural design. Words cannot do it justice: the picture is the only effective way to start to describe it. This is a big two-story box, built over the top of a fragile existing building. The underside of the box is 86 ft (26m) above street level. Students remained still inside the old building while construction was going on around and above them. There were serious concerns about vibration – not only its effects on the academic life; but more significantly, upon the stability and safety of the old building, which rests somewhat shakily on shallow spread footings.Steel stilts that look like toothpicks when scaled against the new and existing structures support the box. The stilts are much sturdier than they appear from the pictures, but it is easy to visualize the complexity of the loads they transfer to the foundations below."

Jan 1, 2004

By Walter E. Vanderpool

Type 1B micropiles (Bruce and Juran, 1997) can be installed rapidly and efficiently. During an 85-day period, 536 micropiles were installed to depths of 61 meters within a site 41 meters by 43 meters. Their performance, as measured by load test, varied even where the materials, construction procedure, and installation technique were closely monitored and controlled. The variation in displacement, as measured by the standard deviation, exceeded 50 percent of the mean test-load displacement for all loads up to the maximum load applied (2670 kN). This study provides a statistical basis to predict variability with respect to the construction method, micropile materials, and installation technique. The variability of displacement at all test loads is a fundamental characteristic of this type of drilled deep foundation system.

Jan 1, 2002

By Djk Arentsen

A new technique to drive tubular piles by impact hammer inside the pile has confirmed a dramatic reduction of noise and the opportunity to save steel. Also a reduction in driving time and a higher bearing capacity has been observed during a test program of this technique. As part of the so-called "Down-the-hole" driving technique, a wave equation analysis has been developed to calculate driveability and pile stress. The main feature of the new "Down-the-hole" technique is the development of a patented device allowing uncoupled penetration of pile tip and pile shaft, which makes it possible to drive both closed or open end piles and reduce the stress level induced in the pile wall. During a test program, a number of instrumented piles were driven and compared with traditional driving of the same pile with the same hammer on top (also instrumented). Also the stresses and performances were compared with precalculations. This paper, explains the technique and presents the test and noise results, in comparison with traditional top-pile-driving. The "Down-the-hole" driving technique is an interesting alternative for special applications where traditional pile driving requires a large wall thickness or in areas where noise is a hot item.

Jan 1, 1996

By Frank Haehnig

Ground freezing is a technique which is used more and more in tunnelling under complex ground conditions. This paper will present three case studies which highlight different aspects of the ground freezing technique when applied in urban environment. The first project is the City-Tunnel in Leipzig, Germany, which is being built beneath the central station and which is the largest ground freezing project currently under construction in Germany. The second case study is part of the North-South-Line project in Amsterdam, Netherlands where ground freezing will be carried out to al-low the TBM drive through old wooden foundation piles. The freeze tubes for this project will be driven using Horizontal Directional Drilling (HDD). The last project is the Hallandsas Tunnel Sweden where the ground freezing equipment has to be installed against high water pressure. The paper illustrates that ground freezing can be implemented in difficult ground conditions such as soft ground, highly fractured rock and high water pressure. The case studies highlight the importance of good workmanship. With the increasing numbers of large tunnels being constructed in difficult ground conditions the paper concludes that the complex case studies presented will be-come more representative for future tunnel projects in urban environments.

Jan 1, 2008

By G. Ranjan

The designers and the practicing engineers have started using latest and cost effective techniques of ground improvements which utilise the weak and poor sub-soil deposits efficiently for the civil engineering construction. In the present investigation, a new concept of 'skirted granular piles' has been advocated. An effective method of construction of granular piles as an economical alternative to vibroflot, and the skirt has been developed. The construction technique is based on indigeneous know how which effectively utilises the man-power technology avoiding import of costly equipment suiting to the developing countries. Full scale insitu tests have been carried out at four sites, having different soil conditions, on virgin weak sub-soil, and improved ground by casting plain and skirted granular piles. Effectiveness of different types of skirt has been demonstrated through insitu tests. A simple analytical approach has been proposed to predict the ultimate pile capacity. The predicted values of ultimate capacity have been found to demonstrate a good correspondance. Granular pile behaviour in terms of pile depth, diameter, spacing and stress deformation characteristics of the improved ground have been discussed. A significant improvement in ultimate capacity in improved ground has been noted. This is further augmented when granular pile group is skirted.

Jan 1, 2010

By Andres M. Baquerizo, Matthew E. Meyer, Carlos Ortiz

"The Metropolitan Miami development, a downtown mixed-use complex developed by Miami-based MDM Development Group, has weathered the economic downturn by adapting to the needs and pressures of the local market. The development (a.k.a. Met Miami) epitomizes the term “mixed-use urban development” with its combination of condominium ownership, rental apartments, hospitality, office and retail components within Miami’s urban core. Initially conceived and conceptualized in 2004, the development has gone through several concept changes. Today, the global USD $900 million development approaches completion.The foundation evaluation, design and construction for this development included the use of innovative and state-of-the-art augered-cast-in-place (ACIP) piles. The testing for these elements included (1) the first-ever, multi-level O-cell load test of an ACIP pile, (2) a world record 5,200 ton (46,261.5 kN) equivalent top load test of an ACIP pile, and (3) continued the advancement of the ACIP pile industry to include the deepest and largest diameter pile installation to date. Those dimensions were up to 36 in (914 mm) in diameter, and 120 ft (36.6 m) deep. The project showed ACIP piles were a proven alternative for structures exceeding 70 stories in South Florida.The development includes four parcels. Met 1 and Met 2 are completed, and the construction of the Met 3 development is just beginning, with completion expected in 2014. Once the Met 3 development is completed, the design and construction phases of the project will have spanned a decade. The Met Square portion of the development, which will be a retail and cinema component, is proposed for the parcel between Met 1 and Met 2."

Jan 1, 2012

By John P. Turner, Steven S. Dapp, Dan A. Brown

"The Goethals Bridge Replacement (GBR) spanning the Arthur Kill Waterway between Elizabeth, NJ and Staten Island, NY consists of a dual-span 1,982.5-ft long cable-stayed bridge with approach spans of 2,545 ft on the NJ side and 2,788 ft on the NY side. The bridge is supported on over 200 drilled shaft foundations ranging in diameter from 4.5 ft to 10 ft and socketed into Passaic Formation siltstone. Drilled shaft resistances for design were based on load tests as described in a companion paper (Dapp et al. 2016). This paper presents the main foundation design considerations and challenges. The approach to construction of the rock sockets, with a focus on quality in order to support the use of high nominal values of side and base resistance, is described. Lessons learned from this project and their application to future similar projects are presented.INTRODUCTION AND BACKGROUNDThe Goethals Bridge Replacement (GBR) project is a Public-Private Partnership (P3) that represents a major milestone for the Port Authority of New York and New Jersey (PANYNJ) in its distinguished history of bridge building in the greater New York City metropolitan area. The new bridge will replace the existing Goethals Bridge, named after Major General George W. Goethals, Chief Engineer of the Panama Canal and the first consulting engineer for the Port Authority. The existing Goethals Bridge along with the Outerbridge Crossing and the Bayonne Bridge comprise the three Port Authority bridges connecting Staten Island with New Jersey. The existing Goethals Bridge and the Outerbridge Crossing are cantilever truss structures and both opened on the same day in 1928. They were designed by J.A.L. Waddell under the supervision of the eminent engineer Othmar H. Ammann (1879-1965), who was the designer of many other iconic bridges in the NY City area including the Bayonne Bridge (1931), the George Washington Bridge (1931), and the Verrazano Narrows Bridge (1964). The designer of record for the replacement Goethals Bridge is Parsons Corporation, which is the successor firm of Robinson & Steinman, whose principal David B. Steinman was also a notable NY area bridge designer and a contemporary and rival of O.H. Ammann.The replacement Goethals Bridge is supported on over 200 rock-socketed drilled shaft foundations. Each main pylon tower is supported on a group of six 9-ft diameter drilled shafts and each anchor pier is supported by two 10-ft diameter shafts. Each approach pier consists of a two-column bent with each column supported on a rock-socketed drilled shaft. A rendering of the Main Bridge crossing the Arthur Kill is shown in Fig. 1."

Jan 1, 2016

By Peter Faust

"The south access road to San Francisco’s Golden Gate Bridge, known as Doyle Drive or Presidio Parkway, needs to be replaced. Built in 1936, it is the primary highway and transit linkage through San Francisco between counties to the north and south. The roadway is tucked into the natural contours of the Presidio and the Golden Gate National Recreation Area, one of the nation’s largest urban parks.The old steel truss structure will be replaced by a new concrete cast-in-place bridge. The foundation design of the new bridge is based on drilled mono shafts below each bridge column. Most shafts required large diameter permanent steel casing installed under strict vibration limitations since several historic landmarks are near the project alignment. Malcolm Drilling decided to use the largest oscillator in the world to install the piles.The area occupied by the Presidio is generally hilly, sloping down northwards to San Francisco Bay. In the western half of the project route, two bluffs rise steeply to about 80 ft (25 m). The bluffs are separated by a valley 60 ft (18 m) deep and 1,500 ft (457 m) wide, which is spanned by the old and new bridge. Overburden soils in this valley are made up of artificial fill, slope debris, ravine fill and Colma Formation, a fine to medium-grained sand unit with clay beds. The Bay Muds encountered in the project area are typically soft clayey silts, becoming medium stiff with depth.The basement rocks underlying the overburden belong to the Franciscan Formation, described as shale, sandstone, serpentine and greywacke, it is extremely variable in hardness, fracturing and weathering. The material can vary from very hard to very soft, can be slightly to very intensely fractured and almost not weathered, to totally decomposed within relatively short distances both laterally and vertically. Rock strength can vary from too weak to be tested to serpentine layers with unconfined compressive strength of 15,000 psi (103MPa) or higher. Groundwater levels in the area are typically no more than 10 to 20 ft (3 to 6 m) below the ground surface."

Jan 1, 2012