Search Documents

By Abdelhak Bentriou

The choice of tool for the first well of an oilfield or gasfield is an important factor, given that we will be drilling with the same type of tool for the entire phase and explains why we need to have another type for comparison based on the efficiency of the tool and its ability to crush the rock, and the wear of different types of tools. Development of theoretical and practical tests to determine the optimal regime for drilling is required to take into account the characteristics of rock layers crossed. Classification of boring tools is based on the geometry of the teeth and depends on the hardness, the abrasiveness of rocks as well as their hydraulic system, but it is better to classify them according to the working conditions with a coefficient designating a discriminant. This is called physical characteristic of the drilling tool. The goal is to designate each element of the tool by a coefficient. Results were obtained from laboratory tests. Modeling the initial rate of progress by different types of tools allowed us to determine an adequate mathematical model of the speed initial progress in clean conditions. Using experimental data and statistics we have established the mathematical model of the average speed of progress as a function of time. With these equations we can determine the wear evaluation and analysis of these factors as an approach to classification according to their characteristics. The main equations for the selection of drilling tools will be based on the optimization of drilling parameters for each type of tool. After analysis, we choose the tool that gives a better forward speed with an optimal load and axial rotation.

Aug 1, 2013

By R. E. Bou Serhal

Many miners are exposed to dangerously high levels of noise on a daily basis. Over the past 15 years, a continually increasing number of occupational hearing loss has been reported from the mining community in the United States, of which, more than 95% is attributed to prolonged noise exposure. Although the noise exposure levels may differ between coal miners and metal and non-metal miners, in the absence of noise control at the source, the solution is the same: use of personal hearing protection devices (HPD). While protecting the miners? hearing it is also essential to no longer hinder their ability to communicate. With access to an advanced HPD that is customized to the miners? ears we are able to combine these two requirements. Using an intra-aural instantly custom molded HPD miners are protected from high levels of noise. The HPD is equipped with wireless capabilities, and contains both a speaker and an In-Ear Microphone (IEM). Therefore, the miners? speech may be captured from inside the ear and transmitted to the remote listener. This IEM signal is relatively noise-free since it is isolated from the background noise. The IEM speech signal, however, is ?boomy? and is missing some high frequency content, making fricative consonants hard to understand. Nonetheless, the IEM speech signal is correlated with the natural speech signal and may be manipulated through statistical techniques to more closely resemble natural speech. By improving the intelligibility and quality of the IEM signal, numerous applications may be enabled. One use of the enhanced IEM signal will be for radio communication. Using wireless radio communication in a noisy mining environment is sometimes the only practical and affordable solution to allow communication between miners equipped with personal hearing protection devices. Traditionally, one of the weaknesses of such wireless radio communication lies in the lack of designating receivers: whether they are the intended receiver or not, all those carrying a radio receiver are subjected to the broadcasted signal. The current work will detail a new concept of a "radio-acoustical virtual environment" where the radio signal will only be received by miners within a given spatial range, such range depending on the user?s vocal effort as well as the ambient and perceived background noise levels.

Aug 1, 2013

By J. Palarski

Hard coal, mined in Silesia Region as well as in the eastern part of Poland, is a key national resource. In Polish underground coal industry, modern mining technologies have been successfully tested and used in the last 50 years. More than 98% of the coal produced underground is extracted by longwall mining method. Current underground coal mining expands into increasing depths. The use of conventional coal extraction methods ? room and pillar and longwall with caving - is becoming increasingly difficult. The coal mining is modifying existing methods and is testing innovative technologies. Backfill is an important component of modern underground mining operations. In Polish underground mines, backfill is recognized as an integral component for extraction of coal from greater depths in a densely populated environment. The modifying and innovative methods require the use of backfill or grouting of caving to provide structural support in underground excavations and to ensure that the mining operations are safe. Depending on the geological structure, mining conditions and environmental requirements there are several variations of longwall methods used in underground coal mining in Poland, in particular: longwall with caving, longwall with backfill, longwall with grouting of caving area. This paper will discuss the different components of an effective longwall production and filling process of caving area. The paper will give a overview of the current application of backfill technology, focusing on Polish coal mining operations. This paper will also briefly describe how backfill contributes to an innovative method ? underground coal gasification. The paper discusses specific requirements for fill materials and the technology of backfilling for underground coal gasification (UCG) operations and problems of implementation and correlation of backfill parameters with other processes that occur during thermal processing of coal.

Aug 1, 2013

By D. Djokic

One of the most attractive features of electron beam curing as a process for manufacturing composite structures is the potential for attaining very low levels of residual stress as compared to thermal curing. This residual stress reduction is important both for the potential to reduce composite failure strains at low operating temperatures and the associated reduction in process-induced deformation. Previous work has demonstrated that it is possible in some cases to significantly reduce residual stress development during irradiation and also avoid development of additional residual stress during post cure. In this paper, simple L-shaped composite laminates were used to study the development of residual stress and deformation during thermal post-cure of specimens that were already partially cured using different radiation doses. Following post-cure, these specimens were also subjected to high-temperature loads to study creep behaviour under service conditions. Aerospace

Jan 1, 2006

By S. A. Vazhnov, A. G. Kalimov, A. A. Potienko

In this paper we describe a mathematical model of the magnetic field and magnetohydrodynamic processes simulation in aluminum reduction cells developed in St. Petersburg State Polytechnic University, Russia. The model includes: (a) calculation of the currents in the busbar system and inside the aluminum cell construction elements including cathode and anode structures, aluminum and electrolyte layers; (b) magnetic field simulation using the integral equation method; ( c) investigation of the magnetohydrodynamic characteristics on the basis of a shallow-water approach. The developed model was used to investigate operational characteristics of the different industrial aluminum cells. Calculated magnetic field distributions and MHD stability parameters were compared with the available experimental information; the comparison demonstrated a reasonably good agreement.

Jan 1, 2006

By R. S. Douglas

Introduction The mine at Copper Mountain of the Granby Consolidated Mining, Smelting and Power Company was one of the pioneers in the use of blast-hole diamond drilling for ore breakage. This method of mining has now been brought to a high degree of perfection. The system in use has?been described in a previously published paper which has become an important part of the literature o the blast-hole drilling method. At the time of the establishment of the system at Copper Mountain, standardized loading and drilling procedures were set up. These procedures were based partly on the results of experiment and partly upon the judgment of men experienced in breaking rock in the mine. The success of the method has been proof of their adequacy. With the progress of scoping in the mine, the diamond drill method of breaking was applied to other ore blocks where different conditions obtained. It was found necessary to make adjustments in the standard procedures to get the best results under the new conditions. The following paper attempts to express, in terms of mathematics, the relations of the variable factors. Until recently, estimations of drilling required were based upon the tonnage to be broken and the proposed rate of explosive loading. A revised method of estimating is outlined below which is direct and which involves no unrelated variable factors.

Jan 1, 1947

By J. Stumper

The control of the distribution and movement of liquid water is crucial for increased reliability and durability of PEM fuel cells: whereas the proton exchange membrane requires a minimum amount of liquid water for optimum operation, water excess in the GDL will impede reactant gas access to the catalyst layer thereby reducing performance. In order to understand the relationships between water management on one hand and fuel cell performance and durability on the other, Ballard has been developing a number of minimally invasive techniques that can throw light on the role of liquid water for both cell performance and durability. This paper introduces a novel measurement method that can provide information about the amount and distribution of liquid water under operation. It is shown how the MEA Resistance and Electrode Diffusivity (MRED) method can be used to determine i) the amount of liquid water in the fuel cell, ii) the pure ohmic cell resistance and iii) the O2 -diffusivity of the cathode. Furthermore, through a combination of the MRED method with current mapping it is possible to determine spatially resolved MEA resistance profiles.

Jan 1, 2005

By A. Jafarnia

Aluminum alloys are frequently grain refined during solidification in order to promote the formation of an equiaxed grain structure in the casting. The application of Ti-based grain refiners and/or Ti containing master alloys for improving mechanical properties may result in formation of Al-Ti based intermetallics. Although the grain refinement produces many desirable qualities in aluminum castings such as improved castability and mechanical properties, the addition of Ti to Al-Si foundry alloys may lead to the formation of some undesirable intermetallic particles such as AlTiSi and cause a number of operational problems such as nozzle blockage due to segregation and agglomeration of aluminide particles within the nozzle. There are several questions to be clarified when minor amount of Ti is added to Al-Si alloys. They include nucleation and growth of AlTiSi particles, their morphologies and orientation relationships with aluminum matrix and the dissolution of these intermetallics during the course of solidification and/or post solidification treatments. The current study was initiated to study the process and possible mechanism of aluminide dissolution and the related phenomena such as segregation and agglomeration. It reports the results found during reheating of laboratory prepared Ti-added A356 alloy at three temperature ranges of below solidus, mushy zone and above liquidus.

Jan 1, 2004

"Coupon testing has been used to investigate stress corrosion cracking (SCC) of rockbolts in a laboratory based experimental program. This program has focused on the use of ASTM G39 three- and four-point bent beam coupon specimens, immersed in an acidified sodium chloride test solution containing hydrogen sulfide. The specimens were loaded to a range of stresses from zero, to just above the materials yield strength. It was found that only specimens above an applied stress of 580MPa failed by means of SCC, showing that rockbolts loaded to near their yield strength may be susceptible to SCC in-situ.INTRODUCTIONStress corrosion cracking (SCC) is a failure mechanism that affects material through the growth of hairline cracks when exposed to a corrosive medium while under stress (Jones and Ricker, 1999). SCC has been found to affect rockbolts in the Australian underground coal mining industry and has the capacity to cause the catastrophic failure of ground support systems, potentially leading to falls of ground in underground excavations, injury or death to mine personnel, damage or loss of equipment, and loss of productivity through the loss of roadway access (Crosky et al, 2002).Coupon testing utilises small scale samples that are intended to be indicative of the behaviour exhibited by a material in-situ (ASTM G39). The small scale, and usually high surface area to volume ratio of coupon specimens mean that they corrode at faster rate proportional to their mass, greatly reducing testing times. The small scale of the specimens allows them to be more easily prepared and handled, loaning them to mass manufacturing techniques.A previous study conducted by Vandermaat et al (2012b) into the use of three- and four-point coupon testing in-situ in an underground coal mine failed to result in SCC of the specimens. This paper serves as a follow up laboratory investigation in order to understand why these specimens did not fail. Previous studies into the SCC in rockbolts carried out by Gamboa and Atrens (2003) determined that rockbolt steel has a critical stress threshold of approximately 90% of the material ultimate tensile strength (800-900MPa). This study will focus on this critical stress threshold as a possible explanation for the lack of failure in the in-situ specimens (Vandermaat, 2012b)."

Jan 1, 2015

By C. V. Corless

THE origin of various types and groups of ore deposits was some years ago a subject of much controversy. To this statement the copper-nickel deposits near Sudbury afforded no exception. Not since the Report of the Ontario Nickel Commission, in 1917, has there been any serious discussion of the origin of this very important group. This may be because, from the opening-up of Murray mine by the British America Nickel Corporation until the recent work at Frood mine, no new ore-body of importance has been developed in the district. The controversy fifteen or twenty years ago between those who favoured the theory of magmatic segregation, among whom Dr. A. P. Coleman was the leading exponent, and those who considered that most, if not all of the Sudbury deposits could more satisfactorily be accounted for by the theory of replacement, will be remembered by many members of the Institute. Perhaps, as too often happens in controversial discussion, each side tended to overemphasize the importance of those geological phenomena which seemed to be most easily accounted for by the theory it favoured. A more balanced view would perhaps admit that replacement was probably predominant in the formation of most of the offset deposits, and magmatic segregation in that of most of the marginal deposits . But there is danger in generalization. Each body of ore should be studied by itself, and no general conclusion of this kind should be allowed to warp the judgment in making such a study.

Jan 1, 1929

By S. Mamonov, V. ?shikhin

"The purpose of work was the significant increase of copper recovery from slag at a concentrating plant. Analysis of study of slag phase composition showed the perspective of a slow slag cooling method due to its recrystallization and transition of primary copper minerals to secondary.Copper content in base slag varied between 0.71 and 0.96%. The study of a degree of copper minerals release of the slowly cooled slag in comparison with a yielding slag showed that in a flotation size grade –0.071 mm of yielding slag the weight ratio of released copper minerals grains is 58.95% against 86.73% in samples of slowly cooled slag. The process flotation sheet consists of three main, one control and two cleaner flotation operations with aftergrinding of middling products. A reagent mode was differed from a factory one by decreasing the slurry pH from 11–12 to 8–9. This paper shows research results of the slurry alkalinity impact on technological indexes of beneficiation (flotation).Industrial testing of a resulted batch of slowly cooled slag at “SUMZ” concentrating plant showed the efficiency of such processing: copper recovery to a copper concentrate increased by 15–19%.INTRODUCTIONIntensive development of mining and metallurgy industries within a 250-year period in the Ural region led to forming of approximately 315 man-made mineral formations at the territory of the Sverdlovsk region. The region contain over 32.5 billion tons of barren rocks and out of balance ores, over 1.5 billion tons of tailings, over 115 million tons of slimes, and over 100 million tons of metallurgical slag (Demin et al., 2000). Latters, at average, contain 407 thousand tons of copper, 2519 thousand tons of zinc, 7 tons of gold, and 150 tons of silver (Rudoy et al., 2011). Wastes generated in mining processing and metallurgical sector of economy contain not only thousands tons of copper and zinc, but cause significant damage to the environment where they are located. The reduction of negative impact of anthropogenic wastes on the environment as well as the storage volume reduction of valuable metals from dump slags is possible by improving the efficiency of the melting and further flotation of slags formed during this process."

Jan 1, 2016

By G. Simard, D. Boudeville, A. Leclerc, A. Boivin

"The objective of this work is to study the various parameters that affect the overflow clarity of gravity settlers used in the precipitation circuit of alumina hydrate from the Bayer process. A mathematical model incorporating the size distribution of the feed suspension (Multi Size Group model), its diphasic nature (Schiller Naumann model) and the presence of turbulence (Shear Stress Transport model) has been solved numerically using ANSYS-CFX software. Preliminary results indicate that the overflow clarity is mainly controlled by lateral diffusion of fine particles (~20µm) from the exit of the feed well and by their upward transport from the sediment bed interface. Also the turbulence pattern in the settling zone seems to play a significant role in this vertical transportation. The validity of the model has been verified by comparing the measured solid concentrations from a pilot classifier with the calculated ones. This model could provide mineral processing plant operators and designers with a tool to optimize the configuration of classifiers with respect to the overflow clarity.INTRODUCTIONProblemIn the Bayer process, alumina hydrate precipitation from the saturated liquor is initiated in settler by adding crystallization seeds. Most of the precipitated alumina settles to the bottom of the tank while the liquor and the remaining alumina rise to the top, where they are removed at the overflow. Ideally the overflow clarity, which depends on the operational mode of the classifier, should be controlled within targeted limits."

Jan 1, 2016

By Yongqiang Liu

Background For refractory gold ores with high carbonate contents ! Acid pressure oxidation ! High acid consumption (if low sulfur content) ! Low oxidation efficiency due to CO2 in autoclave ! Problems with slimy precipitates (gypsum, etc.) ! Alkaline pressure oxidation ! Difficulty in fixing arsenic ! Low gold dissolution due to iron hydroxides/oxides coating ! High reagent costs Summary ! Carbonate and sulfide minerals had similar floatability across the pH range tested (5 - 12) using sodium oleate as a collector; ! Thioglycollic acid or citric acid depressed the flotation of pyrite but could not depress chalcopyrite when used alone; ! Combination of thioglycollic acid and citric acid had a much stronger depressive effect, and the mixture depressed chalcopyrite as well as pyrite between pH 8 and 11 without affecting the flotation of calcite and dolomite; ! Calcite could be separated from chalcopyrite and pyrite; dolomite could be separated from pyrite but not from chalcopyrite under the tested conditions.

Apr 1, 2005

Productivity and efficiency of diesel-powered underground trucks and LHDs can be enhanced through the application of a range of advanced technologies. In addition, these machines are subject to ever more stringent emissions control requirements. This paper will review how various technologies can improve usability, maintainability, and performance of LHDs, through a number of examples. The use of instrumentation and monitoring to understand the role of operator practice on mucking efficiency, as well as the use of finite-element analysis to evaluate structural design, and the use of control techniques to modify operator inputs and hence decrease power consumption, will be presented.

May 1, 2002

By Jiachen Wang

Longwall top-coal caving mining is one of the major mining methods for extracting thick coal seams in China. The top-coal caving longwall mining was began to use in the 1980s in China, and got the rapid development. The development of the top-coal caving mining technology in China, the achievements and the theoretical aspects progress of this method are described in detail in this paper. And the main technical model of China's top-coal caving mining is introduced in this paper. This paper also introduces the application of large-cutting-height mining in China and the technical level it has reached.

Aug 1, 2013

In Canada and other countries, legislation dealing with accurate factual disclosure for mining projects is being expanded to include more metallurgical design information. Grinding characteristics, metallurgical recovery of contained metal and environmental hazards associated with tailings disposal will be part of the Canadian package. This paper will examine only that portion of the plant design standard practice that relates to grinding ? in SAG mills and ball mills that grind ore from as received crushed material to final ground product that is fed to downstream plant recovery processes. Since grinding plants represent a significant portion of the overall concentrator cost, accountability in grinding design should no longer be left to chance, opinion, or hidden proprietary information. This is the 21st century. It is reasonable to expect that a factual basis will be needed so that a Qualified Person (QP) reviewing the grinding mill design can understand it. That will also involve how many and what quality of samples are taken to define the characteristics of the deposit, the accuracy of the tests used to measure ore hardness and the method by which the dimensions and power of the mills are determined. If these criteria are not met, the QP may have no choice but to call attention to the lack of convincing information regarding the grinding mill design for the project. At the same time clients are expected to demand getting the correct design information at a cheaper price, results in a more timely way, and accurate design to the point where the risk of tonnage shortfalls are reduced or eliminated. Tables will be presented to show how this can be done to current standards using existing technologies. At the same time it is acknowledged that current standards are ill-defined and that to achieve consensus among those involved in SAG mill design work, it may require that a consortium funded project be set up to establish what tests and methods for grinding design are suitable to meet the new standards for metallurgical disclosure. By running parallel design methods on several major projects over a period of 5 years, the process of how to design grinding circuits will be better understood because the projects will start at the design stage, include procurement of the mills and will end with a benchmark test on the plant. Selecting the samples and the best schedule for doing test work on core samples submitted and mill design, will be discussed in this paper. The issue of completing the grinding design in time for early procurement decisions is on the critical path for most major projects. Discussions between mining engineers, geologists and process engineers are needed early in the development cycle, at the scoping study level (SS), preliminary engineering assessment (PEA), prefeasibility study (PFS), and at the feasibility study stage (FS), to ensure that proper planning for design sample selection is done. Using adequate sampling and testing methods in a timely way allows early procurement of the grinding mills and minimizes project risk.

Jan 1, 2012

By B. Oraee-Mirzamani

One the most important tasks after excavation of tunnels is the implementation and installation of a support system. Tunnel collapse poses a safety hazard and can cause worker injuries. In addition, it may have a severe economic impact because tunnel collapse can stop production and ore transportation. Therefore, an appropriate and well-designed support system is necessary for collapse prevention and to help stabilize the tunnels. In this research, we suggest a support system for the Parvade1 underground coal mine. The study case is a common mining roadway tunnel in the E1 longwall panel in this mine. To design an appropriate support system, we used the finite element method (Phase2 software). The results of this research can be used to design support systems for future tunnels in this mine and any coal mine that has similar conditions.

Aug 1, 2013

By Peter S. Jack

"IntroductionTHE ORES treated at the concentrator of the Britannia Mining and Smelting Company, Limited, Britannia Beach, B.C., have always contained some lead, but it was not until 1950 that the combination of lead headings and lead price was such that recovery of this metal at Britannia became worthwhile. In that year, with the mining of a new orebody, the lead in the mill feed was raised from 0.07 per cent to 0.15 per cent. Chalcopyrite, sphalerite, and pyrite concentrates are produced by flotation at Britannia, •and 95 per cent of the lead in the mill feed reports with the chalcopyrite concentrate, so that the rise in lead headings was reflected almost wholly in the lead content of the copper concentrate. In 1950, investigation was started to determine if some of this lead could be recovered economically."

Jan 1, 1953

By D. L. Johnston

"Function and ApplicationsWater-only cyclones, (WOC) are a dynamic mineral separator which cause minerals to separate in a water medium by virtue of difference in specific gravity. Figure 1 shows diagramatic plan and sectional views of a water-only cyclone.A slurry of mineral matter and water is fed through the inlet opening under gravitational or pump pressure. The combined effect of centrifugal action and conical shape is to concentrate the heaviest fraction of mineral on the periphery and bottom of the cyclone. This layer of higher specific gravity particles increases in thickness and density between the cyclone inlet and apex. The action in the bed of higher gravity particles formed in the flattened portion of the cone surrounding the tip of the vortex finder deter;nines the specific gravity of separation or cut-point. Mineral particles of lower specific gravity flow with the bulk of the water, out the vortex finder. Mineral particles of higher specific gravity flow with little water out the apex. A more technically e:mct description of the functioning of the water-only cyclone can be found in previous publications noted in the references.The water-only cyclone was invented and refined by J. Vis man, formerly of the Canadian Mines Branch staff, between 1958 and 1965. The first industrial application noted in the literature was when it was introduced as a cleaner for fine coal in 1962. Since 1970 the water-only cyclone has become a common separation apparatus in many Canadian and foreign coal processing plants. The only other mineral industry application known to the author is in separation of gold bearing heavy minerals from sand<'>. The potential does exist for other applications and this area deserves to be investigated more thoroughly than it has been."

Jan 1, 1989

"The North Star and Don Jon copper deposits lie beneath the waters of Thompson Lake, which is 12 miles east of Flin Flon, Manitoba. The deposits were discovered during the years 1949 and 1951 by diamond drilling done in the vicinity of pyritic showings on the shores of two small islands in the lake. The Don Jon ore body lies 1, 700 feet southeast of the North Star orebody and is connected with the North Star mine workings by a crosscut on the 600-foot level (Figure 1 ).Production began on January 1, 1955, at a combined rate of 200 tons per day. The ore is trucked, on 24 miles of highway, to the Hudson Bay Mining and Smelting Co., Limited mill at Flin Flon.Regional GeologyRocks in the Thompson Lake area are Precambrian volcanics, ranging in composition from andesite to rhyolite, with related tuffs and breccia. These rocks have a general north-south trend and are steeply dipping. The area is part of the Lac Aimee fault block, which probably is the southward extension of a south-plunging syncline now thrust some miles to the north. This regional deformation has produced many subsidiary zones of intense shearing and crumpling. It is in two of these zones of shearing and drag-folding that the orebodies occur. The only recognizable intrusive is a narrow diorite sill which trends northeasterly near the west shore of Thompson Lake.The North Star MineA pyritic showing, carrying some chalcopyrite, was discovered around the year 1930 on the west side of a small island near the west shore of Thompson Lake. This ground was included in a group of claims acquired by the Hudson Bay Exploration and Development Co., Limited in 1947.In the years 1949 to 1951, a diamond drilling program outlined a copper sulphide orebody. This ore zone comes to surface beneath the lake, about 300 feet north of the pyritic showing on the island."

Jan 1, 1949