Search Documents

By K R. Brentley

"Tshepong Mine, Harmony’s largest gold producing mine, is situated in the Free State portion of the Witwatersrand Basin, east of Odendaalsrus and north of Welkom, South Africa. The Basal reef is a narrow tabular conglomerate and is the main gold bearing ore body. The strata strikes mainly in a northsouth direction with an average dip of 22 degrees. Currently mining takes place at depths of between 1 690m and 2 150m below surface. The Basal reef unit consists of a conglomerate ranging between a few and 30cm in thickness. Some 80-90% of the gold occurs in the lower portion of the conglomerate. Directly above the conglomerate is a quartzite placer unit, the Basal quartzite, which is a clean, hard competent rock and varies in thickness between 50cm and 200cm. The Basal unit is overlain by the Khaki shale which can vary between 30cm and 500cm in width. It is weak and incompetent khaki coloured chloritic shale.A method of stoping, termed “undercut”, is practiced in order to remove the lower 15-20cm of the gold rich strata. The method entails removing this portion along with some 70-80cm of footwall host rock which is a strong competent quartzite. The hard competent quartzite overlying the conglomerate is left in-situ to form a competent hangingwall which can stabilize and prevent exposure of the weak Khakishale. This method of extraction was developed through trial and error and has been used reasonably successfully since its inception in the early 1960’s where the method was developed to extract the Basal reef at the Western Holdings Mines. Recently prospect drilling and a number of localised hangingwall failures indicated that the residual quartzite beam could be less than 60cm and in some instances as thin as 30cm in certain areas of the mine. The result of this is a less stable hangingwall which not only poses a safety risk to workers in these areas but also had the potential of locking up some 840 000 Tonnes of gold bearing ore. At the present gold price this amounts to revenue of approximately ZAR1.5 billion (U.S. $143 million).This paper discusses the method of “undercut stoping” and existing practices in place at Tshepong Mine. It also explores new initiatives such as the use of a simple freely-supported elastic beam solution to perform back analysis, on-site data capturing of beam thickness and support geometries in order to develop empirical design charts and numerical modelling to assist in the verification of the empirical design method."

Jan 1, 2015

By P. Reyes

The Codelco Chile El Teniente Division Caletones Smelter has an objective to smelt 1,250,000 tonnes per year of copper concentrate. This is a great challenge for the smelter facilities and particularly for the acid plants. The analysis ensuring that there are no obstacles to achieve the production capacity was of great importance. Therefore a series of activities were undertaken as well as studies dedicated to reach the target. This paper presents work focused on a fluid dynamic study, translated in an operation methodology of integrated handling of the smelting and converting gases with the objective to optimize the gas flow and S02 concentration. The optimization should be done employing the current installations, equipment and instrumentation and/or minor modifications. In the first part of the work the condition of the instrumentation involved in the gas handling was checked, improvements determined and the corresponding corrective actions were carried out. The proposed operation method consists of operation of the Cleaning Gas Plant 2 (TC' s gases) and operation of Gas Cleaning Plant 1 (the remaining gas plus the gases from CPS). The implementation of the operation method involves the modification of the valve of the gas into the duct to plant 1 from On to Off to modulate flow. After modification a three days test was carried out. To evaluate the tests, a "Sulphur Capture" indicator was used. During the test the behaviour of the effluent treatment plants was closely examined. No problems or unusual operating conditions were observed. The reduced flow of gas to Gas Cleaning Plant No. 1 permitted the start up of the 2nd test day treating most of the gas received by Gas Cleaning Plant No. 2. The operation was carried out with the limitation not to increase the effluent pond level, which was maintained constant.

Jan 1, 2007

By Farzad Mohammadi, David Kratochvil, Patrick Littlejohn

"With more rigorous regulations being enacted in the mining industry, a need exists for cost effective and environmentally compliant technologies to remove selenium from mine impacted waters to ultra-low concentrations. Existing selenium treatment methods have high life cycle costs, introduce risks of acute fish toxicity, and produce biological waste residues that represent future liabilities. Furthermore, achieving selenium discharge limits of less than 4 ppb is a challenge for existing technologies. Selen-IX™ is a technology developed by BioteQ that selectively removes selenium from mine impacted waters to less than 1 ppb. The technology is purely physico-chemical and takes advantage of the basic principles of ion exchange and electrochemistry. Unlike conventional electrocoagulation that removes suspended solids and breaks emulsions or oxidizes heavy metals, the electrochemical process employed by Selen-IX™ relies on creating conditions where iron acts as a highly effective reducing reagent transforming selenium from a dissolved species into elemental selenium bound in a solid phase. The iron-selenium by-product of Selen-IX™ is an inorganic, non-hazardous and chemically stable solid. Due to their high iron content, the solids produced by Selen-IX™ are of interest to the steel making industry as a low cost feedstock. This offtake potential can not only reduce the life cycle cost of selenium removal by reducing disposal costs but more importantly, eliminate the risk of future environmental liabilities. In this paper, the basics of Selen-IX™ technology are presented along with results of successful piloting on streams from coal and copper-gold deposits.INTRODUCTIONVarious contaminants are released into mining wastewater during the extraction and processing of metals. One such contaminant is selenium. A naturally occurring element found in rocks and minerals, mining activities accelerate its release into the environment. Selenium in trace quantities is essential to all life forms but at higher concentrations it can be harmful, especially to aquatic life where selenium bioaccumulation can lead to reproductive deficiencies."

Jan 1, 2016

By Sean Hillacre, Arthur Lieu

NexGen’s approach to uranium processing design including the crushing/grinding and leaching of raw ore through to yellowcake precipitation and tailings management focuses on minimizing surface footprint, freshwater consumption, and human radiation exposure. Applying the concept of best available technologies economically achievable (“BATEA”), NexGen continues to research, evaluate, test and validate various advanced technologies that can be incorporated into the Project design, including distinctive tailings storage techniques. Additionally, NexGen is proposing that tailings generated from the mill processes be used as cemented paste backfill of stopes, as well as stored in a purpose-built, Underground Tailings Management Facility (“UGTMF”) comprised of several dedicated chambers. The paste backfill method of tailings storage is used globally, however, constructing purpose-built tailings chambers in waste rock is a new concept in uranium mining, which would typically be cost prohibitive for most projects given the expense to develop non-economic material for the sole purpose of storing tailings. The Rook I Project is uniquely positioned to implement the UGTMF due to robust Project economics and favourable technical setting which provides NexGen with the opportunity to set an elite standard for tailings management. When compared to conventional surface tailings management facilities, storing tailings underground as cemented paste reduces geotechnical, geochemical, environmental, and human health risks associated with tailings management. Additionally, the UGTMF vastly reduces the area of surface disturbance and allows for progressive decommissioning during the life of mine operations.

Jan 1, 2020

By L. Fernandes

A two level factorial study was undertaken to investigate the relative impacts of factors affecting the kinetics of polytetrafluoroethylene, PTFE, assisted pressure oxidation of chalcopyrite. A copper flotation concentrate, principally composed of chalcopyrite, was leached in 850 mL of leach solution under conditions similar to those of the CESL process. The factors manipulated were: the amount of 1/8" PTFE beads added (100 g or 650 g), oxygen pressure (690 kPa or 1030 kPa), and concentrate addition (10 grams or 65 grams). Copper extraction data, which indicated complete leaching under certain conditions, were fit using a shrinking core model from which rate constants were estimated and further used to generate a statistical model containing only the factors of significance and their interactions. Results indicated a strong positive effect of PTFE addition and a strong negative effect of increasing pulp density. A weak negative interaction between increasing PTFE addition and pulp density was attributed to PTFE/concentrate agglomeration.

Jan 1, 2014

By Gabriel G. Walton

Conventional numerical modelling tools for analyses of underground excavations are well suited for modelling elastic behaviour and yield response of geomaterials with very simple constitutive behaviour. Non-dilatant elastic and perfectly plastic behaviour is most commonly used for preliminary analyses in the absence of the data required to consider more complex behaviours such as strainweakening and dilation. For truly brittle models, this deficiency is more acute. Current state of practice allows only for reliable estimation of the volume of failure, but not for any prediction of displacement. In fact, there is no consensus in rock engineering regarding the most accurate approach or most suitable tool to model the magnitude of the plastic deformation that strain-weakening or brittle rocks experience at tunnel boundaries, particularly when support is incorporated into these models. This problem is largely a function of a poor understanding of how inelastic dilation occurs in different types of rockmasses, the rate controls on strength loss and volume change during yield, and the complexities of rock-support interaction in yielding conditions.

Jun 1, 2012

By L. Hacini, N. Van L ê, P. Bacher, D. Thibault

Manufacturer welded components may suffer from high level of residual stresses which can cause premature cracking and decrease the life of the components if they reach values close to the yield strength of the material. In the present work, a robotized hammer peening technique is simulated by an impact machine and the residual stresses generated by the indentation are measured. To better understand phenomena behind residual stresses relaxation by hammer peening, the impact energy level was changed. 304L steel plates were hammer peened with 10 impacts. The contact between the hammer and sample surface was always at the same location. The strains on the surface close to the impact location were recorded during the test using strain gauges to follow residual stresses variations. At the end of the test residual stresses were measured indepth using hole drilling technique at 8mm from the impact center. The micro-hardness was monitored to evaluate the affected zone by the hammer peening. This approach gave a good estimation of the energy and number of blows to be used for efficient relaxation of the manufactured parts.

Jan 1, 2006

By George A. Guess

The making of contracts for the purchase of ores is a business which the metallurgist usually understands better than the miner. Companies in the custom ore business often employ an ore buyer who is aware of the class of ore which the smelter needs, and is thoroughly conversant with the business. The miner on the other hand makes ore contracts but seldom, and it is often only after a settlement has been made that he realizes the meaning of the terms of the contract under which he has sold his ores. He has expectations usually greatly in excess of the amount 'net proceeds' shown at the bottom of the settlement sheet. Seldom does the occasional shipper really know his contract. A somewhat similar parallel is to be found in insurance policies. We all have insurance policies; we never know the conditions contained in them until after the fire. The clauses in the policy are for the protection of the Insurance Company. An Insurance Company has no friends.

Jan 1, 1926

By Colin Jones

Canadian Clay Products Inc., which mines bentonite in Saskatchewan near Truax and operates a plant at Wilcox, is the sole producer of swelling bentonite, often called western bentonite, in Canada. Seven products produced by the company are used in binders, sealants, water and waste water treatment, plasticizing agents, foundries and absorbents. Reserves are reported at about one million tonnes for the deposit but the area in general contains significant additional reserves.

Jan 1, 2001

By René Dufour

Jusqu?à son acquisition par MM René Dufour et Alain Robin en 1994, les claims miniers et les droits de surface de la propriété étaient détenus depuis 1953 par la société Québec Columbium, une filiale de la socité américaine Kennecott Copper qui y a réalisé d?importants travaux miniers. En 1995 la compagnie NIOCAN inc. fut incorporée; ses actions furent inscrites à la bourse de Montréal en 1997, et à la bourse de Toronto en décembre 1999. Jusqu?à maintenant, NIOCAN a investi plus de 7 millions de dollars dans le développement de sa propriété minière de niobium située à quelques 40 kilomètres au nord-ouest de Montréal. Le haut rendement économique des deux gisements principaux que compte exploiter la compagnie, le S-60 et le HWM-2, a été établie par des études de faisabilité effectuées par le consortium Met-Chem/SNC-Lavalin. La mission que s?est donnée NIOCAN inc. consiste à mettre en production ses deux gisements et à devenir ainsi productrice de ferroniobium dans les plus brefs délais. Figure 2 Le projet est présentement à un stade avancé d?obtention du certificat d?autorisation du ministère de l?Environnement. À plus long terme, la compagnie compte aussi exploiter les sous-produits de ses gisements (apatite, forsterite, magnétite, calcaire et terres rares).

May 1, 2003

By T Nakamura, M. Itoh

Most of the used cathode ray tube (CRT) glass in Japan, which contains lead oxide, was exported and recycled in overseas factories of new CRTs. However, domestic treatment and recycling of waste CRT glass has become necessary because overseas CRT factories have shut down and exports of CRT glass have stopped. Some of the waste CRT glass recycled domestically is charged in lead blast furnaces instead of silica flux, because there is no local reproduction route for glass that contains lead. However, the mass of CRT glass that can be treated in this manner is limited because of its high silica content. Consequently, additional treatment methods for waste CRT glass are required so that more can be used as a lead smelting material. In this study, waste CRT glass was treated with hydrofluoric acid to dissolve the silica contained in the glass, and the dissolved lead was recovered by precipitation. Lead metal was recovered by electrodeposition from the prepared hexafluorosilicic acid solution.

Jan 1, 2011

By A. Poor Zaeif Doost

With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.

Jan 1, 2012

By Benoît Valley

Optimization of the mining sequence in terms of economics (maximizing net present value) often leads to multi-front mining methods generating pillars. Significant resources are tied up in these pillars, but mining them is often challenging. In order to improve our understanding of rock mass behaviour while extracting these pillars, an extensive monitoring program has been designed and implemented at Vale?s Coleman mine (Sudbury, Canada). The program focuses on existing and new technologies that have potential for monitoring deformation and rock mass property changes. It includes both active and passive methods: gravimeters, multi-point borehole extensometers, fiber optic strain meters, fixed and portable three-component seismic arrays, borehole imaging and sonic logging, and, repeated LiDAR surveys. This paper reports results from an initial project phase, when only a small amount of mining has taken place. The goal was to test and compare technologies in order to assess their sensitivity, accuracy, repeatability and suitability for underground mining conditions. Value is gained by having a broad range of monitoring devices running side by side, enabling comparisons and benchmarking.

Jun 1, 2012

From 1999 to 2008 rock related accidents accounted for 75 fatalities, nearly 6,000 injuries and almost 14,000 incidents (Pappas and Mark, 2011). Clearly this shows that rock related safety on coal mines remains a serious issue and more effort is needed to address this hazard. This paper reviews support design considerations and monitoring needed to improve rock related safety in room and pillar coal mines in the USA. From the present study design considerations continue to evolve and improvements in technology and a better understanding of failure mechanisms and methods to prevent these failures from occurring are in place. At first glance, the design of safe and efficient underground openings appears simple until the designer begins to realize the complexities and variability of geometries, geology, loading and stress influences, support designs and other factors such as corrosion and economics. Ultimately the goal of all designs is to ensure that it can be completed safely, last for the duration of the design life and it is economically feasible.

Aug 1, 2013

By Nathan Deisman

Coupled reservoir geomechanical simulations have become a key component of caprock integrity assessments for SAGD operations. This work demonstrates the differences of stress evolution when considering coupled versus uncoupled reservoir simulation. Coupled simulation involves the use of a reservoir and a geomechanical simulator with feedback to each simulator to update reservoir or geomechanical variable (permeability, porosity, relative permeability, pressure, temperature, saturations). Uncoupled simulation only passes the pressure and temperature to the geomechanical simulation with no reservoir simulator updating. Therefore, it is possible to complete uncoupled simulations exclusively with no knowledge of geomechanical flow property evolution. However, it is important to understand the differences between the stress evolution in each model for caprock integrity analysis. A single geological model was selected and parametric analysis was completed while varying the geomechanical the production injection pressures (1600 kPa, 1900 kPa, 2200 kPa) for a reservoir with an initial pressure at the injector of 1300 kPa. The results of the six uncoupled and coupled models are compared through the changes in mean stress, shear stress, and strength with focus on geomechanical assessment of caprock integrity.

Jun 1, 2012

By Kazem Oraee

Implementing stable final pit walls in open pit mines during the open pit design phase and mine exploitation has become one of the most important concerns of mining engineers in recent years. Failure of mine walls can potentially cause loss of life, roads blocks, and damage to mining machinery, temporarily or permanently halt production at the face and in the worst case scenario, close the mine. Thus, the role of creating stable mine walls is crucial to safety and general operations of mines and any effort to optimize this process has great economic value for mine operators. This paper aims to illustrate the technical aspects of use of the successful presplit blasting method in metal open pit mines. It also shows that using this approach not only increases safety in mines through wall stabilization, but also will boost economic profits by savings in stripping ratio. In this regard, appropriate practical concepts for designing the drilling and blasting patterns and the role of selecting the correct drilling rigs are elaborated in detail through conducting a case study in Chador Malu iron ore mine in Iran.

Aug 1, 2013

By Fadi Layyous Gedeon, David Hatton, Solomon Mogashoa, Tuhin Banerjee, Faisal Aljohani

The adoption of innovative technologies in mineral processing often raises concerns about complexity and integration. However, Woodgrove’s Direct Flotation Reactor (DFR) technology at Barrick’s Jabal Sayid copper concentrator provides a different perspective. This paper outlines the smooth integration of DFR technology from piloting to full-scale commissioning, showcasing how easily the cells were brought online. Installed in a cleaner scalper role, DFR cells at Jabal Sayid upgrade re-ground rougher concentrate to final concentrate in one stage. Despite processing challenging ore, the DFR cells delivered concentrate grades that consistently exceeded expectations. The commissioning process was straightforward with minimal hurdles, highlighting the technology's user-friendly nature. This paper advocates for a shift in perceptions about new technologies in mineral processing. The success of DFR technology at Jabal Sayid demonstrates that “different” doesn’t mean “difficult.” By focusing on ease of commissioning and operational integration, innovative solutions can enhance processes, improving efficiency and productivity in the mining industry.

May 4, 2025

By Patrick Laflamme, Jean-François Boulanger

Les minerais de cuivre sulfurés, qui représentent 80% de la production mondiale de cuivre, imposent une étape de concentration des minéraux, premièrement pour atteindre une teneur en cuivre minimale qui permette le traitement pyrométallurgique, mais aussi pour limiter la présence d’élément pénalisants (délétères). Cette introduction offre un survol des principes, limites et pistes d’améliorations touchant la concentration des minéraux de cuivre.

May 2, 2024

By Hervé Toubon, Matthieu Davrinche, Jim Corman, Mamane Bello Boubacar Kinassa, Pierre Amadieu

Orano Mining maintains a significant level of Innovation and Development Research for its sites in Canada, Niger, Kazakhstan, Mongolia, and France. This effort is formalized within the six major thematic programs below, which include more than one hundred affiliated R&D projects:  Geological understanding, tools and methods for exploration  ISR technology (geology, modeling, mining development tools)  Mining technology (SABRE)  Ore treatment and processing (in particular via our Centre for Innovation for extractive metallurgy, CIME)  Environment (radiochemistry, modeling, tools and methods for remediation)  Digital Mine (sensors, transmission, database, and data modeling) This paper describes the main actions of these six programs, their stakes, and their progress. There is no single path leading to innovation but fostering an innovative context and a structured project approach are essential ingredients to successful development and industrial deployment. As a result, Orano Mining has, over the years, developed a disciplined methodology for R&D portfolio and project management. This methodology, presented here, targets a reduction in time to implementation while valuing both the expertise and the work in project mode.

Jan 1, 2020

By M. Hamamoto, M. Furuta, S. Tanaka

The Tamano smelter and refinery has expanded its production from 228kt/y to 260kt/y since 2006. It was not a big jump, but efficient and economical improvements were executed. These were not only de-bottlenecking and modernization of the smelting plant, including the acid plant, but also additional processes were commissioned, e.g. slag cleaning furnace and steam dryer. On the other hand, a conversion to permanent cathode process in the #2 tank house made the biggest impact on production efficiency for the refinery plant. In order to overcome the drastic change of copper business, although each scale is not so big, continuous improvements are very important to survive. This paper mainly describes the recent improvements of the smelting plant.

Jan 1, 2007