Search Documents

By A. Ghahreman

Activated carbon is proven to be able to catalyze arsenic oxidation in aqueous solution under acidic conditions. A commercially available granular coconut shell based activated carbon (AC) has been evaluated for catalysis of arsenic oxidation in this study. The rapid small-scale column test (RSSCT) has been developed to simulate and predict the performance of a carbon-based arsenic treatment system in a pilot scale reactor. Effects of residence time, aeration rate, and initial arsenic concentration in the influent solution on the AC catalysis of arsenic oxidation under dynamic and continuous conditions were studied by manipulating these parameters during RSSCTs. The effectiveness of the AC on arsenic oxidation was examined over the course of constant diffusivity based RSSCT operation. Residence time and initial arsenite concentration are proven to be the most effective impacting parameters on the arsenic oxidation process. For the 218 min residence time, the highest steady-state arsenic oxidation efficiency achieved was 98% with 1 g/L As(III) being treated at pH=1 under 0.05 L/min oxygen aeration. In a long-running RSSCT, the oxidation efficiency did not seem to deteriorate over a course of 666 hours operation, corresponding to 13986 mL total influent throughput volume. INTRODUCTION Arsenic is toxic to both animals and plants and inorganic arsenicals are proven carcinogens in humans. The increased extraction of low grade and complex mineral resources has introduced high ratios of arsenic into metallurgical processes. Discharge of arsenic by acid mine drainage resulting from mining activities has added intensive pressure on the need for proper treatment (Lawrence & Higgs, 1999). Since trivalent arsenite is more toxic and has lower affinity to solid surfaces for adsorption, many treatment systems initiate with an oxidation step to convert arsenite to arsenate and reach the ultimate immobilization of arsenic by the following precipitation of arsenate (Nazari, Radzinski, & Ghahreman, 2016). Scorodite precipitation has been studied extensively as a means of arsenic immobilization due to its high stability and negligible potential of releasing arsenic (Filippou & Demopoulos, 1997). As a stable ferric arsenate mineral, crystalline scorodite can contain up to 30 wt% arsenic (Paktunc, Dutrizac, & Gertsman, 2008). Arsenic must be in its pentavalent oxidation state in order for scorodite to be precipitated via oxidizing ferrous ions (Clancy, Hayes, & Raskin, 2013).

Jan 1, 2019

By John D. Carriere, Jean Leung, Daniel. Laguitton, Michael .. J. Burrows

"The objective of this expert system application in a copper-zinc concentrator, is to increase the availability of assay data through substitution for erroneous data. The assay data is used by the Operations personnel and automatic process control strategies to control flotation circuit performance. Two online X-ray fluorescence analysis systems analyze 24 streams across four divisions to provide the required data. Data availability of individual streams average 90% while the resulting circuit availabilities are 70%. The unavailability of correct data results from mechanical, X-ray or process problems. The erroneous data can be identified by process experts using knowledge relating stream interdependencies and historical process behaviour. An expert system was devised to provide real time identification of erroneous data and substitute for that data with the ultimate aim of improving metallurgical response by both the operator and automatic control systems.The paper discusses the early development work and architecture of the knowledge base designed using Neuron Data's expert shell NEXPERT.INTRODUCTIONThis paper describes the early development of an expert system (ES) prototype at the Kidd Creek concentrator. The project is a joint undertaking of the Kidd Creek Division of Falconbridge Limited and CANMET. Kidd Creek entered into the project to apply heuristic rules to the XRF assay data to improve the metallurgical control of the flotation process by increasing availability of analysis data. This project provided a problem of suitable size and future expandability while making use of a wide base of in-house expertise and experience. Another important benefit is the introduction of expert system technology to the site providing tools and experience for future system selection and technology application. CANMET has an on-going interest in assessing various aspects of ES technology (hardware, software, knowledge engineering, integration) while addressing problems in process operations that could most readily benefit from the technique. CANMET's role in the project was to provide project assistance, financial support, substitution algorithm assistance and software for data substitution. The knowledge bases (rules) have now been completed and are to be tested in the online environment."

Jan 1, 1989

By J. C. Salas, A. Weishaupt, J. A. Guzman

The origins of the electrorefining process date back to 1869, when the first ER cathodes were produced at Pembrey, South Wales. By the time that Pembrey was closing, Chuquicamata tank house was under construction, initiating in 1915 a long history of electrolytic cathodes production. Initially electrowon cathodes and later electrorefined cathodes were produced. During the history of Chuquicamata tank house, there have been several challenges associated with the quality demanded for electrolytic copper. Among them, the transformation from electrowinning to electrorefining in 1952, the onset of the direct commercialization of ER cathodes and the phase out of wire bars in the 80s, several technological changes including the implementation of permanent cathodes, and certainly the constant increase in complexity of the anodes refined. This paper explores the manner in which Chuquicamata has addressed these challenges and examines its links to process characteristics, which have been necessary to maintain a product quality according to market requirements and a brand, “CCC”, that is widely recognized worldwide. INTRODUCTION Located in the north of Chile, in the Atacama Desert, Chuquicamata is an open pit copper mine that for many years has played a relevant role in the global and local mining industry. Known from prehispanic times, the Chuquicamata deposit was initially developed between 1912 and 1915 by the Chile Exploration Company, the operating company of the Chile Copper Company controlled by the Guggenheim Brothers in the USA (Yeatman, 1916). Officially inaugurated on May 18th, 1915, by the President of Chile who pressed a button in Santiago sending a telegraph signal to the power generation plant specially built in Tocopilla, 1500 km north. It signaled the beginning of generating energy, sending it to Chuquicamata, another 140 km east (“El mineral de Chuquicamata”, 1915), marking the beginning of its industrial operation.

Jan 1, 2019

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

By Ali Bunjaku, Lauri Pesonen, Hannu Johto

It is well known that there are many ways to process copper concentrates into copper anodes using the pyrometallurgical route. All modern copper smelting technologies are fundamentally energy efficient and environmentally safe options, and therefore choosing one depends on the desired capacity range, feed impurity levels, plant location, flexibility needs, overall energy use, and of course smelter economics in both the short and long term. This paper focuses on comparing different solutions which have potentially the lowest variable opex (operational expense), meaning in practice finding out which technology offers the best chances for profit maximization under certain scenarios. For the comparison, we chose to have a closer look at Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC), Outotec Flash Smelting (FSF) – Outotec- Kennecott Flash Converting (FCF), Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC), Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF), Mitsubishi Smelting Process (MIT), Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC), and Side Blowing Furnace (SBF) - Top Blowing Converting (TBC) since these seem to be the main state-of-art technologies now being applied in many recent copper smelter projects around the world. The work was carried out by modelling each smelting route by using the new HSC SIM 9 simulation software and applying operation time, energy, and consumables consumption numbers for each unit process and stream. Combined with cost data, the exercise produced a rich set of information which will be shown in detail for each area per scenario. The authors’ goal here was to provide a fair comparison where each technology can be evaluated from various perspectives such as electricity use or refractory consumption. INTRODUCTION Copper can be produced either pyrometallurgically or hydrometallurgically. The hydrometallurgical route is used only for a limited amount of the world’s copper production (~20%) and is normally only considered in connection with in-situ leaching of copper ores. On the other hand, most of the copper extraction from Cu-Fe-S minerals is pyrometallurgical (~80%) (Schlesinger 2011, ICSG 2017). Thus, several different processes can be applied for copper production, including the following state-of-the-art technologies: Outotec Flash Smelting (FSF) – Outotec-Kennecott Flash Converting (FCF) Outotec Flash Smelting (FSF) – Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Peirce-Smith Converting (PSC) Outotec Ausmelt TSL Smelting (ASF) - Outotec Ausmelt TSL Converting (ACF) Mitsubishi Smelting Process (MIT) Bottom Blowing Reactor (BBR) – Bottom Blowing Continuous Converting (BCC) Side Blowing Furnace (SBF) - Top Blowing Converting (TBC)

Jan 1, 2019

By S. Eckert, M. Reuter, O. Keplinger, D. Obiso, N. Shevchenko, M. Akashi

We report on laboratory experiments focusing on bubbling phenomena arising from gas injection through a top submerged lance (TSL) in a liquid metal layer. The objective of this study is to reveal the characteristics of the formation and behaviour of the particular bubbles at different gas flow rates and submergence depths of lance. Visualization was performed in the eutectic alloy GaInSn using X-ray radiography. Argon bubbles were injected through the injection positions at three different submergence depths. Essential parameters such as the bubble size, bubble shape, detachment frequency and the two- dimensional gas distribution in the flat vessel were obtained by image processing. The results show that the deep position of the submerged lance causes an asymmetric large-scale circulation inside the fluid vessel. Bubble detachment frequencies were calculated by Fast Fourier Transformation from fluctuations of the image intensity in the vicinity of the nozzle injection point. This frequency does not show strong variations with respect to changes of the gas flow rate and the submergence depth of the nozzle. An increasing gas flow rate results in an increasing two-dimensional projected bubble area and the occurrence of a significant number of small bubbles being trapped by the strong fluid flow in the liquid metal layer. INTRODUCTION The Top Submerged Lance (TSL) process has been an essential component of the metallurgical industry since the emergence of first concepts about 50 years ago (Floyd, 2005). The process, which is characterized by blowing reactive gas through the submerged lance into a liquid bath, was developed mainly for improving the tin smelting process and has been applied for waste treatment or the production of several metals such as copper, lead, nickel and zinc. The productivity of the reactor is determined mainly by the efficiency of the chemical reaction between the gas or solid particles and the liquid. To achieve a high efficiency requires good exchange between the gas-liquid phase and therefore a large interface area. The efficiency changes greatly with the number and size of bubbles injected from the nozzle and the extent of splashing on the free surface. The degree of turbulence in the bath plays a decisive role here. For the reason, the design of an efficient TSL process requires a profound knowledge of the fluid dynamics especially for complex multiphase flows.

Jan 1, 2019

By Adriana Ramirez, Bradford C. Wesstrom, Blanca Olave

The Freeport McMoRan El Paso Copper Refinery optimizes electrolyte quality using a number of systems. The facility controls copper, arsenic, antimony and bismuth using electro-winning cells within the Tank House and Nickel Carbonate Plant Liberator Circuit (NCP). The NCP manages sulfuric acid content utilizing recycled electrolyte in the slimes autoclave as well as operation of the Acid Purification Unit, APU. The El Paso Refinery removes common sulfates using metal hydrolysis with sodium carbonate. Finally, a Mechanical Vapor Recompression, (MVR), at the water recovery plant removes sodium sulfate generated by the NCP. This paper will provide a summary of these operations. INTRODUCTION In the mid 1920’s Nichols Copper Company, in Laurel Hill, New York, recognized the need for a modern copper refining facility in the southwest. Because of the many railroad heads, affordable power and abundant labor supply, and the close proximity to regional copper smelters in Mexico, Arizona, and New Mexico, El Paso became the ideal location. In December 1928, ground was broken for the joint venture refinery between the Nichols Copper Company, Phelps Dodge, and the Calumet and Arizona Mining Company. In September 1930, Nichols Copper Company became a part of Phelps Dodge Corporation after a stock exchange. In July 1938, Nichols Division officially became Phelps Dodge Refining Corporation. In March 2007, Freeport McMoRan Copper & Gold acquired Phelps Dodge. Water is a precious commodity in the desert southwest, making conservation of this natural resource an important goal for the El Paso Operations. In the 1980’s, work on the treatment of slimes was improved through the use of pressure leaching of the refinery slimes using an autoclave. Due to the high tellurium content in the leached slimes solution, it was crucial to implement a method for its removal before the solution returns to the tank house electrolyte. A copper telluride cementation operation was installed for tellurium recovery and the ability for the recycle of the leachate and wash water to the refinery electrolyte. In October of 1997, ground was broken for the construction of the water recovery plant using an MVR to reuse process water, reducing water consumption by 25%. In 2002, electrolyte purification was further improved with the installation of an Acid Purification Unit, (APU) (Sheedy, Pajunen, & Wesstrom, 2007). The APU recycles 90% of the acids (both sulfuric and arsenic acids) back to the tank house electrolyte. The solution that passes through the APU is treated with soda ash to precipitate metals out of solution as carbonates and generates a sodium sulfate solution. This sodium sulfate solution is easily processed in the new water recovery plant, where the majority of the water recycles back into the plant as pure condensate. In 2012, the power plant at the refinery upgraded its Reverse Osmosis System to provide RO water to the tankhouse. This insured that the refinery would not have to bleed electrolyte for metals contained in well water such as: calcium, magnesium, iron and sodium chloride.

Jan 1, 2019

By R. L. Bruening, L. Navarro, R. M. Izatt, N. E. Izatt, S. R. Izatt

Green chemistry principles will be discussed, and examples will be given of the use of Molecular Recognition Technology (MRT) to selectively separate valuable metals such as rhenium and palladium from various copper refinery feed streams. Recovery of these metals has numerous advantages including (i) conservation of valuable resources, (ii) prevention of environmental damage, and (iii) elimination of capital and operating expenses due to re-processing or disposal of metal-bearing streams. INTRODUCTION Refining of copper ores has a long and successful story. The history of copper, one of the first metals mined in human history, illustrates the global challenges faced as a result of increased demand for major metals and for by-product specialty metals found with them in trace amounts (Izatt et al., 2014). Copper has valuable properties, which have sustained its use over the centuries. It is an ideal material for creation of novel materials. Some desirable properties of copper that have proved valuable in our high-technology society include suitability for alloying with many other metals; ease of joining by soldering and brazing; good combination of mechanical qualities; high resistance to corrosion; suitability for many artistic purposes; and, of great importance in the modern era, efficient and economic use as a conductor of electricity. Copper mining in the U.S.A. began in the late nineteenth century in Montana (Izatt et al., 2014). The estimated total amount of copper mined globally before 1800 is about 5 million tons, four times less than is mined in a single year today (Flanagan, 2018). Production of copper in the U.S.A. has remained fairly constant at about 1,300,000 to 1,400,000 metric tons per annum from 2013 to 2017. Specialty metals such as bismuth, rhenium, molybdenum, and others that have become essential in our 21st century technology, and precious metals such as silver, gold, and the platinum group metals (PGMs) are concentrated by geochemical processes in trace amounts in copper ores. These specialty and precious metals were discarded into tailings in early mining operations, since limited extractive technologies existed and uses for most of them were limited. Thus, economic benefits for recovering them were limited, primarily, to silver and gold. Today, copper processing is the main, and often the only, commercial source for certain of these elements (Izatt et al., 2014). For example, molybdenite (MoS2) is the predominant ore mineral of molybdenum mining (Pohl, 2011). Cu-Mo-Au porphyry ore deposits supply ~75% of the world’s copper, 50% of the molybdenum, nearly all of the rhenium, and 20% of the gold. Typical ore grades are 0.5–1.5% copper, 0.01–0.04% molybdenum, and <1.5 g/ton gold. Molybdenite is the primary source for rhenium, among the rarest of metals, which is an essential component of super alloys, such as turbine blades in the aerospace industry (Pohl, 2011). Most rhenium is obtained as a by-product of molybdenite from copper mines in Chile. The case of rhenium raises an important issue. Continued availability of rhenium, selectively concentrated in copper ores, depends on continued mining and processing of copper. Since the mining company’s main interest is typically in copper production, continued recovery of rhenium and other specialty elements present in the ore body is at risk. Dependence of specialty metal supply on continued mining of major metals exists in several additional cases including indium, gallium, selenium, tellurium, germanium and bismuth (Pohl, 2011). PGMs, on the other hand, are typically mined for their own value, which far exceeds that of associated base metals. However, copper ores often contain marketable amounts of platinum and palladium, making their separation of interest, if this can be done economically.

Jan 1, 2019

By É. Poulin, J. Bouchard, E. M. Pérez-García

Process control and optimization have always been crucial aspects in the mineral processing industry, and expectations constantly increase to cope with more stringent security, quality, efficiency, and environmental performances. The main challenges to reduce variability of key process variables, and steer profits to higher values while maintaining sustainability indexes within acceptable ranges come from nonlinear responses and circulating loads. The most commonly implemented control strategies rely on simple PID controllers for practical implementation and maintenance considerations. If arguably good performances are accomplished when these are adequately set up, there is also room for further gains by using more advanced methods such as model-based techniques. There is thus a need for more realistic process and equipment models. Based on advances of the past few decades, this paper introduces an autogenous/semi-autogenous mill (AG/SAG) model to be included in a modular comminution circuit simulation toolbox comprising ball/rod mills, material handling, and classification devices. The proposed mill model incorporates a modified version of the classic comminution equation that makes grinding rates proportional to the energy input. It requires the determination of a selection function (fragmentation rates) and a breaking function (fragments distribution). The former is modelled with an S-shaped curve characteristic of AG/SAG processes and the latter is a size-relative distribution of the produced fragments. The power draw is predicted employing the empirical equation of Austin. The paper also develops a case study to illustrate how the proposed simulation framework can capture the behaviour of an actual plant. Model calibration consists in an optimization problem that search the global minimum of the difference between predicted and measured/estimated size distributions, power draw, solid fractions, etc. Results demonstrate that the mill simulator can mimic an actual process in its operation conditions. INTRODUCTION Comminution is a key stage in the mineral processing industry, obviously because the phases of interest must be liberated to be able to recover them. In general terms, the global performance of a plant depends largely on the efficiency of the grinding circuit and on the material properties such as its grindability, density, and mineral grades. The subject has vastly been studied since as early as the 19th century, when Rittinger (1867) and Kick (1883) developed some of the first empirical models to relate grinding and energy input. The great interest in the subject comes from the fact that this operation is costly and, probably most concerning, highly inefficient. Buckingham et al. (2011) estimated that ore comminution can represent up to 60% of the overall plant power draw. Moreover, only a modest fraction of the power draw effectively translates into rock fragmentation. For grinding, estimates range between 1% and 25%, depending on the reference used, while the rest is mainly lost as heath (Fuerstenau & Abouzeid, 2002; Tromans & Meech, 2002; Bouchard et al., 2017).

Jan 1, 2019

By T. Fliß

The protection of natural resources is of essential importance in times of rapidly increasing populations and resulting shortage of agricultural land. Soil and groundwater resources play a central role for the production of food or feed of any kind. The intensive agricultural and environmentally friendly use of these resources must ensure sufficient income and sustainability of life for future generations. Mining projects often represent a particularly deep intervention into ecosystems due to their size as well as the most expensive treatment processes. Conventional mines comprising of shafts and developed mining fields require the stockpiling of waste rock and in particular to potash mining, the discharge of brines from raw salt processing. In contrast, mining operations based on the solution mining method can be operated without major environmental impacts and lower security risks. While the solution mining for the production of rock salt finds application since more than 500 years, exist a procedure to produce potash using solution mining only since the 1980&apos;s. For solution mining drill holes are used to exploit the potash, launched from the surface into the deposit. The exploitation of the raw material occurs by the dissolution of the potash injecting solvents and creating so-called brine caverns. Currently, a number of mining projects in Carnallite deposits by the solution mining method are in progress around the world. Often these projects are located in sensitive ecosystems. K-UTEC project and support actual a solution mining operation of a Carnallite deposit for a Chinese customer in South-East Asia. This work comprises a comprehensive geological and geomechanical modeling as well as stability analyses. Furthermore the cavern design and brine field layout as well as the planning of the brine processing and the plant design. The present paper introduces this project as a case study. The application of a special solution mining procedure and processing design ensures an emission-free mining operation (Zero Disposal Plant). The emission-free operation is achieved by utilizing the full extent of the caverns to dispose the liquid solutions from processing. The presentation of principal salt processing and technical equipment will be rounded by information about the geology of the deposit. Since the deposit includes a number of sensitive minerals, such as Tachyhydrite and Bischofite the presentation comprise a lot of interesting items with special view at the brine field operation. K-UTEC designed and delivered a special blanket measuring system and a well cement according the request of the customer. K-UTEC, a research and engineering company with more than 60 years of experience in the sector of potash and rock salt mining, developed the world&apos;s first solution mining operation for Carnallite in Germany more than 30 years ago. In recent times K-UTEC served in different solution mining projects worldwide, with special view at the environmental impact, as well as the optimal utilization of the deposits.

Aug 1, 2013

By R. O. Burt, R. W. Bruce

"IntroductionGravity concentration, the separation of two or more minerals due to the difference in their relative specific gravity and usually in a fluid medium, is the oldest recorded form of mineral processing.The principles of gravity concentration were known to, and practiced by, the ancients and Hoover's commentary to De Re Meta/lied'' notes many early references.Over the centuries, as direct smelting ores became more and more uncommon, the mineral processing industry developed and along with it many varied methods of concentration. Gravity concentration declined rapidly in importance in the early twentieth century, and it is only in the last decade that its advantages are being re-evaluated.A significant proportion of ores are processed by gravity; a large proportion being in the iron and coal industries<'>, or in the treatment at very high volume of relatively coarse alluvial deposits. The tin dredges of South East Asia and Beach sand plants of Australia are prime examples.An indication of the broad application of gravity concentration is the variety of minerals presently recovered. A list is given in Table 1; this list is not exhaustive.Principle of Gravity ConcentrationGravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid, such as water or air.The relative movement of minerals to one another is achieved by a variety of methods. These are: separation in a fluid of intermediate density (heavy media separation); by stratification (such as in jigging); in a flowing fluid (cones, spirals, sluices etc.) and with a horizontal shear (shaking tables etc.)."

Jan 1, 1989

By Victor Dolmage

"The localization of orebodies by geological structures is well demonstrated at the Copper Mountain mine of southwestern British Columbia. These extensive deposits; owned and workd by the Granby Consolidated Mining; Smelting and Power Company; are at Princeton; abo!lt 150 miles east of Vancouver and 40 miles north of the International boundary. The geology of the deposits and the surrounding district is described by the present writer in Memoir 171 of the Geological Survey of Canada; pub1ished in 1934.The main geological feature is a gabbro stock, elliptical in plan, with a major axis about 5 miles in length extending in a northwest-southeast direction. The stock varies in composition from syeno-gabbro (gabbro plus orthoclase) through diorite and syenite to a core of syenite pegmatite. All the members contain orthoclase, which ·increases greatly in amount toward the centre, but all are devoid of quartz. The stock has been injected into a steeply folded series of volcanic flows, breccias, and tuffs that strike more or less parallel with the major axis of the stock. On its northeast side the stock is flanked by a band of fairly coarse volcanic breccia of andesitic composition and ·having fragments up to several inches in length. Where this breccia is tangential to the stock it is both dynamically and chemically metamorphosed to a marked degree, and within the zone of this metamorphism are enclosed the copper deposit~. The ore consists of bornite, chalcopyrite, and a little magnetite occurring as disseminated grains and small veinlets in the metamorphosed breccias. The only gangue minerals are orthoclase, albite, oligoclase, and biotite. The two most common vein minerals, quartz and pyrite, are conspicuously rare or absent. The dynamic metamorphism has produced two well-defined structures, namely, a strong schistosity parallel with the curved vertical contact of the stock and a very striking set of small, straight, nearly parallel open fractures that stand nearly vertical and at right angles to both the schistosity and the stock contact. These are called the ore fractures."

Jan 1, 1954

By J. M. Toye

The Canadian nuclear fuel business relates primarily to supplying fuel for Candu reactors. The product development, manufacturing and marketing activities of our nuclear fuel industry will therefore be determined by the rate of growth of the Candu nuclear reactor business. The nature of this relationship between the Canadian nuclear fuel industry and the Canadian Heavy Water Reactor program will be considered, with particular reference to the factors influencing future economic growth.

Jan 1, 1969

By C. Zangerl, H. Lechner

"Large scale rock slides in deeply incised Alpine valleys are common hazards that can endanger human life, settlement areas and critical infrastructure such as highways, railways and reservoirs (Bonzanigo et al., 2007). In order to perform reliable forecasts of the behaviour of rock slides influenced by large dam reservoirs the geometry, the kinematics, the deformation behaviour and the hydrogeological situation need to be understood profoundly. Based on generic rock slide models the influence of the rock slide geometry on the stability as well as the impact of the buoyancy forces and water load of the reservoir at the toe of the slope are the main focus of this study. Various assumptions of hydraulic conductivity, groundwater conditions of the rock slide and impoundment depth of the reservoir are analysed using limit equilibrium approaches.Generally, deep seated rock slides are characterised by deformation along one or multiple shear zones where most of the measured total slope displacement localizes. Many large rock slides, especially those observed in foliated, mica-rich crystalline rock masses (e.g. paragneisses, mica schists, phyllites), do not fail suddenly or reach high velocities. Instead, many of them move slowly and reach velocities of centimetres per year or even less. Some show episodic accelerations, sometimes reaching alarming levels, but then subside to non-critical levels again. However, there is a potential that deep-seated rock slides fail rapidly, develop into far-reaching run-out rock flows, and cause catastrophic events. Whereas the role of triggers in promoting phases of acceleration is often understood, the same cannot be said regarding the kinematics and dynamic processes by which the rock slide mass decelerates, re-stabilises or accelerates to a catastrophic degree once the trigger impetus has been removed. Thus key questions of the presented work concern the geotechnical, geometrical and hydrogeological conditions under which a slowly moving rock slide is triggered to accelerate to irreversible, maybe dangerous velocities. The development of the sliding zone is generally influenced by pre-existing discontinuities such as brittle fault zones, shear and tensile fractures, foliation and bedding planes. These geological structures determine the geometry of the sliding zone which can either be rotational or translational. During the gravitationally induced failure process the geometry of the rock slide undergoes a change.Several observed post-failure geometries in metamorphic rocks show a concave topography in the middle to upper part of the rock slide and a typical convex or bulge-like topography at the toe of the slope (Zangerl et al., 2012). Whereas the sliding zone of the upper part of such a rock slide mass is rather steep and planar, the inclination of the sliding zone at the toe can be close to zero and act against the driving forces (Alonso et al., 2010). A shear zone that meets alluvial deposits at the foot of the slope encounters a stabilizing impact on the mechanical behaviour. This buttressing effect of alluvial sediments has a remarkable influence on the slope stability."

Jan 1, 2015

By D. W. McDonald

Coal mining and railway transportation are so closely en-twined and so dependent one upon the other that the failure of one would mean the total collapse of the other. With this indisputable fact in mind, there is no doubt that the operator of each is deeply interested in the other&apos;s success. Railway transportation began at the mouth of a coal mine. The first railway car was the English coal-wagon, a crude box on four wooden trowlets, running on wooden rails and holding 1,600 pounds. This was operated by gravity or horse-power in England to convey coal from the mines to the rivers. The first coal-cars used on Nova Scotia railways were of 4 tons capacity with side doors and "V" shaped centres. Then followed flat-bottom, 4-ton cars that operated on tipples, the car bei.ng held in tipple by a chain passing over the top and fastened on either side. Next came the 6-ton car with drop-bottoms, then the 10, 15, 30-ton cars, and now the modern 50 and 100-ton steel cars, equipped with automatic couplers, brakes, and rachet dumping device. Contrast the first coal-car with a modern luxurious pull-man or a I 00-ton coal and ore car, and you have a record of progress in railway transportation. The development of the steam locomotive was no doubt the greatest factor in this progress, but let us not forget that the foundation of all industrial development was and is coal. and that development in mining and railway transportation should keep abreast.

Jan 1, 1924

By Douglas Lay

Attention has been drawn in the publications of the Department of Mines to the view that veins of two different ages occur in the Cariboo district, namely, those of Jura-Cretaceous age and those of pre" Mississippian age. It has been further pointed out that while there is doubtless a wide distribution of veins of pre-Mississippian age in and about the Barkerville and Stanley areas, and in the vicinity of Round Top mountain and Yank&apos;s peak, there is no such wide distribution of veins carrying gold values of commercial significance. Veins of the latter type discovered to date occur almost exclusively within one or other of two comparatively narrow zones, both trending northwest and southeast, the one extending from Island mountain co Round Top mountain, and the other from a point somewhat north of Stanley co Yank&apos;s peak. In addition, there is some evidence of a third zone trending northwest from Spanish mountain, at or near the contact of the pre-Cambrian and Mesozoic rocks. In short, all the evidence from prospecting and lode-mining operations to date indicates that values are mainly restricted co zones having marked directional distribution. Moreover, it can be demonstrated that the placer deposits resulting from the erosion of the pre-Mississippian veins have a similar directional distribution, allowance being made for modifications due to glaciation. The observations offered in this paper are of the nature of a generalization which seeks to explain certain anomalies both in the vein-mineralization and in the -important auriferous-pyrite replacement deposits in limestone which have recently been discovered. For the sake of brevity, the Island Mountain-Round Top Mountain zone will be referred to as Zone No. 1, and the Stanley-Yank&apos;s Peak zone as Zone No. 2.

Jan 1, 1936

By George Booth

In mining operations the cost of timber is an item of much importance, because the life of mine timbers is, in many cases, very short and, as the supply of the better grades becomes depleted, less durable kinds must be used. This, of course, tends to shorten still further the period of service-ability. While it is possible that concrete and steel may, to some extent, take the place of timber in mines, their high initial cost and the difficulty in installation will greatly restrict their use. Moreover, wood, besides being comparatively cheap to handle, possesses other desirable qualities, and for many purposes a satisfactory substitute is hard to find. Both the decreasing supply and the increasing price of timber make its more efficient utilization imperative. AGENCIES DESTRUCTIVE TO MINE TIMBERS Timber used in mines is exposed to destruction from many sources. Wear, breakage, and waste are responsible for much loss. Wood rollers and drum laggings must be frequently replaced on account of the constant wear by ropes. Unprotected timber in chutes and mills is also rapidly worn by abrasion, and track ties in main haulage ways get worn by the feet of mules, cut by ropes, etc. Large amounts of timber are broken by &apos;crush&apos; and &apos;squeeze,&apos; and much temporary timber is buried beyond all recovery in pillar workings and in those mines which resort to back filling. Decay and insect attack, however, cause the greatest damage. If not totally destroyed by one or both of these, the timbers frequently become so weakened that they break under the pressure upon them.

Jan 1, 1926

By G. W. Brooks

This short article is quite different to the general run of papers that are presented to the Institute, but no apology is offered because I consider that first-aid and mine-rescue work are of equal importance to many other subjects that are dealt with in our Transactions. Members of the Institute should be as much interested in the safety of persons engaged in the mining industry as they are in the practical methods of modern mining. We must not only do our best to conserve life and property by adopting every known device to that end, but we must also prepare ourselves so that we may take prompt and effective action when life is in danger, or when property is subject to loss. The need for such preparation in Alberta is perhaps greater than in most places where mining is carried on, and we must spare no effort to assemble at every mine men who are well trained in first-aid and mine-rescue work. The large area over which the mines are distributed renders central training stations out of the question, hence the need for local rescue-teams. Hospitals with skilled staffs, close enough to the mines to be convenient, also seem to be out of the question; therefore the greater need of a high standard of first-aid training for the people in our mining camps. The Government mine-rescue cars are supplied with the equipment necessary for training persons in this essential work and also for dealing with disasters should they occur. The question then arises: are there a sufficient number of men who are trained ? If so we can rest assured that what is possible to be done will be done. But if a sufficient number of trained men are not available much loss of life and damage to property is likely to result.

Jan 1, 1925

By W. L. Stuewe

For the purpose of this paper I shall, in order to limit myself, define the words &apos;Maintenance&apos; and &apos;Equipment&apos; as follows: Maintenance shall mean the &apos;care of or &apos;the sustaining of equipment in as nearly perfect condition as possible. Equipment shall mean any item of a mechanical nature entering into the production of coal; it will be seen that unless one limits the use of this word it could take in administration as well as operative equipment, and include metal mines, mills and smelters, and manufacturing plants. In any industry the first consideration is the proper operation of all units entering into the production of the article manufactured or produced. I wish to quote here what a man, well known internationally in financial circles, told his operators at the time a large expansion programme was under consideration. His exact words were: "I do not care how much it is going to cost. What I want to know is how much it is going to cost to operate and maintain. It is the continuous drain for repairs that costs us the most money." The truth of this statement has been proved time and again, and many companies have found the cost of maintenance to be the balance between profit and loss-so much so that, in two instances with which the writer is familiar, the mechanical equipment was practically replaced throughout. I bring this point out here to emphasize the value and necessity of keeping abreast of the times, and obtaining maximum efficiency with the minimum outlay. Time is indeed money where delays occur due to defective or poorly kept equipment, and it is absolutely necessary to prevent machinery from becoming defective or inefficient.

Jan 1, 1930

By Hans Lundberg

The magnetometer which was developed during the war for detecting submarines has proven exceedingly valuable in outlining deep-seated structures in oil exploration, and will be useful also to geologists in outlining regional structural features in the Precambrian. Our magnetometer has been developed to outline local and detail structures. 1 am quite sure that all geophysicists and geologists would agree with me that, in ore prospecting, it is important to obtain as much detailed information as possible. We know that, as we ascend from the ground and get away from the magnetic ore-bearing structures and orebodies, the magnetic intensity decreases rapidly, but, worse than that, we lose the details even faster. Figure l shows two strong, very sharp, magnetic &apos;highs&apos; over two orebodies which, as our distance increases, rapidly merge into one fairly broad, moderately strong anomaly. If we drilled on this maximum, we would not encounter any of the orebodies. Therefore, we should fly the airborne magnetometer as close to the ground as possible in order to duplicate the results of the magnetic ground surveys. The first chance to accomplish this came with the helicopter, which is an exceedingly maneuverable aircraft. It can be landed in a cleared space not much more than fifty feet square. With floats, it can be landed anywhere, even in a swamp, on thin ice, or on soft snow. It can stand still in the air, hovering over a given point. It can ascend and descend vertically, fly sideways and even backwards, at the will of the pilot. It flies forward at any speed up to l00 miles an hour. The helicopter can be taken to any desired position at a given time. It can fly at any useful altitude from a few feet to several thousand feet above the ground. It can fly very close to the ground with safety. In bare areas, the survey flight may be performed a few feet above the ground. In forested areas, however, the flights, to clear the trees, must be made at l00 to 150 feet. To mark out a certain point, a small parachute-like marker may be draped over a tree or laid on the ground. This can be done from the helicopter without touching the ground.

Jan 1, 1947