Search Documents

By C. -M. Katsari, G. N. Anastassakis

"Copper is considered one of the most important industrial metals because of its properties (conductivity, malleability) and variety of uses. Approximately 70% of the global copper is used for various electrical applications, with a significant part of copper originating from recycling, since copper can be recycled and re-used countless times, without any loss of performance and difference in the quality of recycled copper in comparison to that from ore. Copper recycling significantly contributes to natural resources conservation, waste minimization, energy saving, and overall cost reduction. Approximately, 35% of the globally produced copper originates from recycled copper.The objective of the current work is to investigate the recovery of copper from electric wire scraps using wet shaking table as an alternative to air separation methods that prevail over the wet ones in recycling processes. The tests were carried out using feed of correspondingly high- and low-grade in copper. In the first case, the wire scraps had been subjected to shredding only, prior to tabling separation; in the later, the low-content tailing of prior air separation was used as feed ?n table separation.In regard to testing, the following factors were examined: table tilt, water flow-rate, and reciprocating speed. The results of the tests clearly denote that copper wire separation from plastic polymer is feasible, as in most cases, table separation resulted in heavy products of high purity in copper and high recovery, and tailings of very low copper grade. The results of the current work clearly denote that wet tabling can be applied efficiently for the separation of recycled copper wire from plastic, as an alternative to air separation methods, as well as for the recovery of copper from the low-grade tailings derived from air separation methods."

Jan 1, 2016

By M. Bourassa, R. del Villar, S. St. Arnaud, J. Valenzuela

"Autogenous grinding is used quite frequently for mineral comminution as a result of its lower capital and operating costs. However, it is more difficult to control than conventional grinding, particularly when the autogenous or semiautogenous mill is the only comminution stage (i.e. no secondary grinding is available). Analysis of the control strategy used then becomes extremely important, a task that is greatly simplified by the use of an empirical dynamic simulator:This paper presents the methodology used in the development and the calibration of such a simulator for the autogenous grinding circuit of an iron are concentrator: The various steps are described: industrial data acquisition, preliminary treatment of the gathered information. and empirical modelling of the process. Finally, both the actual and the proposed control strategies are compared using simulation results.This exercise has shown that the variability of some of the controlled variables could be reduced through a better handling of the water addition and the use of filters on some of the signals used for control purposes. The reduction in variability of critical variables, such as power draw, would allow their average value to be increased without the risk of exceeding their safety values. Some advanced control techniques were also tested, with interesting results."

Jan 1, 1995

By Jonathan Peck, Jim Gray

"With the implementation of more advanced monitoring, control and locating systems in surface mines, there is an ever increasing need for their mine-wide integration toward achieving over-all optimization. AQUILA Mining Systems Ltd. is developing the basis for a comprehensive real-time monitoring, control and information system called the Total Mining System or TMS. This system is being designed to address both current and future needs of open pit mines toward improving productivity and minimizing costs, through better two-way information flow between each component in the operation. At a basic level, feedback from equipment and process monitoring will enable decision making to be based on quantitative, on-demand information, thus permitting proactive rather than reactive planning. Dynamic planning would be a valuable tool as market conditions fluctuate, equipment fleets age and variations in the grade, quality, geometry and hardness of the mined material all contribute to either changing production targets or levels of achievable performance. Such a capability could be implemented within the next two years.At a higher level, and within five years, autonomous operation and/or real-time supervisory control of mobile and stationary equipment in open pit mines will be achieved. A discussion is provided in regard to the development and implementation of an autonomous haultruck and blasthole drill, to demonstrate the need for such a system.This paper outlines a preliminary program for the design, development and implementation of this system, primarily in relation to high-level communications and its role in the future automation of open pit mobile equipment."

Jan 1, 1995

By H. E. Wilde

"Zinc has been used for many years as a galvanic coating for the protection of steel. Electrochemical measurements show that zinc actually overprotects steel. The corrosion rate of DQSK (drawing quality semi-killed) steel in air saturated salt water was determined as a Junction of applied cathodic potential. The resulting data indicate that at a critical cathodic over potential of - O. 725 Vsce an acceptably low corrosion rate of less than 1 mpy occurs. Using the developed criterion, alloys of Zn/X and AL/X were produced and evaluated in galvanic contact with steel in a standard laboratory test. The results indicate that Zn /Mn, Zn /Co, AI/Mg/Si and AI/Mg/Ge alloys offer excellent galvanic protection along with (a) no hydrogen evolution, and (b) improved dissolution life over Zn coatings.IntroductionZinc coated (galvanized) steel has been successfully used in applications where bare (or painted non-galvanized) steel would suffer corrosive attack. In general, galvanic coupling to zinc, as either an anode or a coating, is an effective means for combatting steel corrosion. Because of this, the use of galvanized steel has increased markedly, stimulated primarily by automobile manufacurers seeking to extend the corrosion warranties on automobiles(1).Although effective, zinc coatings are not without a number of drawbacks which warrant efforts to improve them. For example, because of the widely differing electrode potentials between zinc and steel ( - 1.05 Vsce and - 0.60 Vscc, respectively, in air saturated NaCl solutions), the zinc corrodes at a rapid rate to protect the steel. This is reflected in the limited lifetimes of galvanized unpainted siding. The basic electrochemistry controlling the situation is shown in Figure 1, for a system controlled by oxygen reduction. The zinc corrodes sacrificially to protect the steel, while cathodically polarizing the steel to a potential near that of zinc's open circuit anode potential."

Jan 1, 1990

By René G. del Villar, Jules Thibault, René del Villar

"Some key control variables of industrial processes, associated with product quality, often cannot be measured directly or frequently enough to establish adequate control. In such cases, it is possible to use available measurements to provide a prediction for these process variables and use them in a control strategy, thereby giving rise to what is now commonly called a softsensor.In some industrial grinding circuits, the on-line particle size analyzer is shared between various sampling points. Therefore, for a given location, the actual measurement is only available every 10 to 20 minutes, a delay which is unacceptable for automatic control purposes. To alleviate this problem, a softsensor based on an artificial neural network has been investigated. First, the structure of the neural network and different schemes for the training process are analyzed. Then, the performance of the neural network softsensor is compared with other inferential methods such as ARMA models and Kalman filters.IntroductionGRAHM, French acronym of the Research Group on Computer Applications in the Mineral Industry at Laval University, began in 1990 a research project on Knowledge Based Automatic Control (KBAC). This project, sponsored by a consortium of eight mining companies and the federal and provincial governments, seeked to screen advanced (knowledge-based) methods for data processing (filtering, mass balancing, etc) and automatic control (model-based) for their use in the mineral processing operations and the transfer of the project results to the sponsor companies.In parallel to more academic research work, a number of case-studies have been undertaken with the cooperation of partner companies. Among such works, a very successful one has been the design and installation of a new control strategy for one of the Kidd Creek (Falconbridge Ltd.) grinding circuits. This project was related to the evaluation of a number of control strategies and the implementation of one of them, as selected by the plant management, in the concentrator.A total of sixteen control schemes were evaluated on one of the dynamic phenomenological simulators developed at GRAHM, a trademark of this research group [ l]. The calibration of the simulator models was done based on industrial data gathered by GRAHM and Kidd Creek personnel. Then, the simulator was used to test the performance of various PID-based control schemes, designed to achieve the control objectives set by the Kidd Creek personnel. The best scheme proposed called for controlling the cyclone overflow particle size by manipulating the water addition rate to the cyclone feed box and the circulating load by manipulating the circuit ore feed. The particle size analyzer (PSI-200) available for monitoring the product size, was unfortunately shared (multiplexed) among various streams of the plant, which meant a 14 min delay between two consecutive readings for any particular stream. This induced the plant personnel to choose an alternative control strategy, one which controlled the cyclone feed density instead of the cyclone overflow particle size."

Jan 1, 1996

By Randy Billing, J. Fraser Wilson

"IntroductionThe job of designing and implementing effective environmental management sounds like what one executive, assuming responsibility for a very sick organization with lots of potential described as, ""an insurmountable opportunity"".Effective environmental management is an opportunity, no doubt. Its an unusual, if not unique opportunity. Insurmountable? Maybe not! Indeed, in the authors' experience, the keys to unlocking this opportunity are not in new or complicated technicalities; they are in the existing strengths and successful experience that one has in managing other complex and exacting management issues.To begin, it is necessary to understand what these issues of sustainable development mean to business. What is the nature of this opportunity? What makes it look unsurmountable?New Games: New RulesLawyers have described some of the new rules companies are facing and there is a new game being played; a game characterized by unique challenges.Take two, for example: • The ecological problems to be faced are Mother Nature's business, the political solutions required are our business. This combination of natural problems and political solutions requires the development of new management mechanisms, to bridge the gaps among us, as individuals, as professions, as interest groups and so on; indeed, even as countries;• and gaps there are : about as many gaps as the people involved : many of them with new and changing expectations, often mutually exclusive and not negotiable.The challenge of these relationships and communications among so many different interests is one of the keys to effective environmental management.Like any game, this one has rules and they are new, too. These rules are evident not just in new legislation - tough legislation with draconian penalties; they are also evident in new and exacting business policies, value driven and just as unforgiving of poor performance. Senior management of many companies are speaking about the role of enlightened corporate policies and how important it is for everyone involved that these policies drive and reflect business practices. Absence of day to- day behaviour which evidences the words in action, the policy on the wall of a corporate office or published in an Annual Report is first evidence for the prosecution , not the defence.The challenge of practical policies is another key to effective environmental management.This is a new game, with new rules: the challenge of change."

Jan 1, 1991

By Y. Mercadier, M. Ait-Ali, M. Dostie

"This paper presents the results of an analytical study to assist in the design of blast furnace tuyeres, including a prediction of the heat transfer process.IntroductionA blast furnace tuyere must be made of a material which must con serve its geometric and structural integrity in the environment of the fire-ball of the furnace. It must be cooled by a fluid forced through its internal cavities in such way as to keep its maximum temperature below the allowable limit. The prediction of the convective heat transfer coefficient inside the tuyere is of great importance in the design of new tuyeres with increased service life. We have developed a computer program which can predict the convective heat transfer coefficient for two-phase flow. This paper shows how the program work s and how it can be used for the numerical simulation of tuyeres.To simulate the h eat transfer conditions in water-cooled tuyeres, one has to predict:a) The heat flux (radiation and convection) generated by the combustion gases. This was evaluated using the single-zone gas-furnace model. This model yields results which are of the right order of magnitude. A more fundamental study of radiation heat transfer based on combustion and gas concentration s will be reported in a future publication.b) The local convective heat transfer coefficient at all points with in the tuyere.Prediction of the Convective Heat Transfer CoefficientTo calculate the convective heat transfer coefficient for refrigerant stream, semi-empirical correlations developed by the nuclear industry were adopted. These correlations permit us to analyze the entire range of the convective boiling range, as shown in Table 1. Our first attempt, with a single-phase flow correlation, has shown the need to take nucleate boiling into account."

Jan 1, 1982

By G. E. Bogin, C. Strebinger, J. F. Brune

"Evidence shows that methane gas emanates from the mined-out area or gob of a longwall coal mine and can travel towards the working face, posing an explosion risk. Since the gob consists of varying levels of compacted rock, many researchers have modeled fluid flow through the gob as a Darcy-type porous media with a specified porosity and permeability. When studying methane gas explosions near the gob fringe, the Darcy flow assumption may not be applicable to describe the methane flame interaction with the gob. Computational fluid dynamic studies were performed modeling methane flame propagation across a simulated gob which was modeled as both a Darcy porous medium and as discrete rock objects with varying sphericity. Modeling the gob as a Darcy porous medium results in unrealistic methane flame propagation since the porous media assumption does not consider any differences in rock size and/or distribution. Additionally, the porous media model does not allow for ignition within and subsequent flame propagation through the porous medium, which must be modeled to understand the potential for methane gas explosions in the gob area. Modeling the gob as discrete rock objects produces more realistic methane flame dynamics and agrees with experimental observations. Modeling results show flame propagation across circles, hexagons, and squares, meant to represent rock rubble in the gob, produce different levels of turbulence which affects methane flame propagation velocity. This research demonstrates that modeling methane gas explosions in a longwall coal mine environment, specifically near the gob area, requires modeling obstacles, such as rock rubble, as discrete physical objects to capture the complex coupling of fluid dynamics, thermodynamics, and heat transfer. INTRODUCTION Although there are methods to mitigating methane accumulations in a longwall coal mine, explosive gas zones (EGZs) of methane and air may exist and pose an explosion risk to nearby miners and equipment (Brune, 2014) (Karacan, Ruiz, Cote, & Phipps, 2011). In the event of an explosion, the resulting methane flame and pressure wave can be catastrophic as evidenced by the Upper Big Branch explosion in 2010 that killed 29 miners (Page, et al., 2011). Since the mining process is transient, it is difficult to determine exactly where these EGZs exist, but investigative reports show in many cases, these EGZs can be near the working face, behind the shields, or within the gob area (Brune, 2014) (McKinney, et al., 2001). Additionally, miners have recounted seeing flames moving back and forth within the gob and under the roof supports (McKinney, et al., 2001) and in other cases, anecdotal evidence of hearing small pressure pops deep within the gob area (Brune, 2014)."

Jan 1, 2019

By Z. Wu, L. N. Y. Wong

The present study develops the numerical manifold method (NMM) as a tool to investigate the progressive failure in rock slopes. The entire processes of the progressive slide surface development related to crack initiation, propagation, coalescence and degradation to eventual catastrophic failure are successfully captured. To overcome the limitation of the original NMM associated with an improper removal of the interface cohesion of the discontinuities, the displacement-dependent cohesion removal method is adopted. Simple examples of failure of rock slopes containing different arrangements of discontinuities are modeled and their results are compared with those based on the popular limit equilibrium method proposed by famous pioneers Jennings and Jaeger. In cases of coplanar non-persistent discontinuities, close results are obtained despite the differences in the consideration of the stress concentrations at the crack/discontinuity tips. In cases of non-coplanar discontinuities, since the influence of the tensile strength is considered by both the Jaegers model and the NMM, the Factor of Safety (SF) values are similar despite the difference in the failure path trajectories predicted by these two models. The results also reveal that the original NMM without the displacement-dependent cohesion removal method is always more conservative due to the improper removal of the interface cohesion. The displacementdependent cohesion method can to some extent alleviate such a limitation.

Jan 1, 2015

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016

By Gabriel Zarate

"Los Bronces had two ROM dump leach operations designated Leach I and Leach II. Leach I was commissioned in 1998 and stopped in 2014 due to the mine requirements. Leach II plant, commissioned in early 2002, was built to treat around 700 million tons of marginal ROM ore averaging 0.45 % total copper. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides.The original electrowinning plant design capacity for copper production was nominal 19,500 tonnes per year at a current density of 276 A/m2 and a current efficiency of 92%. Presently, Los Bronces San Francisco plant typically operates at current densities between 390 and 440 A/m2, much higher than the average in the industry, with current efficiencies around 93% and a maximum copper cathodes production of 37,200 tonnes per year.In order to accomplish these achievements, a number of modifications in the process conditions, in the cell hardware and in the operational procedures have been implemented. In the first case, the specific flowrate, copper concentration and temperature of the electrolyte were modified to accommodate the operational requirements facilitating the increased current density. Associated with the cell hardware, a six cells expansion was added, upgraded equipotential inner cell busbars were installed and the cross section of the cathode hanger bars was enlarged for increased current carrying capacity. Documented operational procedures like short circuit detection and cathode weight control were improved.The modifications implemented and the results obtained are discussed in this paper.INTRODUCTIONLos Bronces Division of Anglo American Chile is located up in the Andes Mountains, northeast of Santiago. It had two cathode plants, Los Bronces at an altitude of 3500 meters above sea level (m.a.s.l.) commissioned in 1998 and closed in 2014 and San Francisco at an altitude of 2800 m.a.s.l. and in operation since 2002.The process is leaching run off mine (ROM) low grade copper sulphide ore in dumps. The mineralogy of this material was estimated to be 70% chalcopyrite, 20% chalcocite/covellite and the balance oxides. The average grade is 0.45% total copper (Cut).At Los Bronces dump, Leach I plant, the pregnant leach solution (PLS) was collected and stored in an underground reservoir. From there, it was fed to a solvent extraction plant with a series-parallel configuration in two extraction stages and one stripping stage. The electrolyte produced was fed to the electrowinning plant having 30 cells and 60 cathodes per cell. Maximum capacity of this plant was 12,000 tonnes per year (tpy)."

Jan 1, 2016

Real Time Monitoring of Cemented Paste Backfill Introduction Methods ?how to instrument a Long Hole stope Key Results from 2 case studies: barricade pressures and displacement, in-stope pressures Importance of Real Time Monitoring How binder, rise rate, cement content affect fence pressures

May 1, 2010

By K. E. Waters, C. Marion, T. Grammatikopoulos, A. Jordens

"The Nechalacho deposit, located in the Northwest Territories, Canada, is a heavy rare earth element (REE) deposit. The main REE-bearing minerals in the deposit are zircon, allanite, bastnäsite, synchysite, columbite (Fe) and fergusonite. Previous work investigated the use of gravity and magnetic separation in the processing of this ore and showed that coarse particles following grinding were enriched in zircon, suggesting the potential for selective comminution. The current work investigates the possibility to selectively comminute gangue minerals and concentrate REE-bearing zircon into coarser size fractions. The ore was ground wet in a laboratory rod mill for various lengths of time (0, 10, 20, 30, and 40 min). The resultant products were analyzed using ICP-MS, to determine the distribution of zirconium and REEs in the different size fractions produced after grinding, and QEMSCAN, to identify mineral phases, mineral liberation and the distribution of minerals. Optimum grind sizes for the upgrading of zircon due to selective comminution were then proposed, and dense medium separation was investigated as a means to further concentrate zircon.It is important to note that this process is not representative of the currently selected process design or recovery for the Nechalacho deposit. Any application of this process to this deposit would require optimization in order to ensure appropriate grade and recovery targets are met.INTRODUCTIONThe rare earth elements (REEs) are the fifteen elements in the lanthanide series of the Periodic Table, as well as yttrium (scandium is excluded in this work). Traditionally, REEs are categorized into two groups: the cerium sub-group of “light” rare earth elements (LREEs); and the yttrium sub-group of “heavy” rare earth elements (HREEs) (Golev et al., 2014). The LREEs comprise the first six lanthanides (lanthanum through samarium) and the HREEs comprise the remaining nine lanthanide elements (europium through lutetium) coupled with yttrium (Golev et al., 2014). HREEs are much less abundant in the earth’s crust and on average are more expensive than LREEs (Seredin, 2010). Of the fifteen REEs, the production of neodymium, europium, terbium, dysprosium and yttrium has been determined to be most critical due to their scarcity, high demand and criticality in many high-technology and clean energy applications, such as in illuminated screens for electronic devices and permanent magnets in wind turbines (Seredin, 2010; U.S. Department of Energy, 2011). These five elements are classified as critical rare earth elements (CREEs) (U.S. Department of Energy, 2011)."

Jan 1, 2016

Some examples of the results of research projects, conducted in the KOMAG Institute of Mining Technology are presented. Special attention is paid to mining machines and equipment, and improving work safety and comfort of miners in underground workings. From numerous scientific and technical achievements of the KOMAG Institute within the last 2 years, a few design solutions have been selected for a presentation. Some results of European projects on innovative solutions are described as well, highlighting KOMAG?s role in the national and international research area.

Aug 1, 2013

By Ken G. Stowe, Stephen L. Chryssoulis, Christian Bendel, Joe Y. Kim, Ewald Niehuis

"TOF-SIMS (Time-of-flight secondary ion mass spectrometry) was used to detect collectors sorbed onto the surface of mineral particles in concentrate and tailings samples from the Brunswick, Matagami and Kidd Creek concentrators. This technique uses ion beams from either Cs or Ga sources to sputter the particle surface, a method which reduces fractionation of the collector molecule during sampling.In the Brunswick Zn circuit, sphalerite particles lost to the scavenger tails had less amyl xanthate and isobutyl xanthate compared to sphalerite recovered to the Zn final concentrate. Xanthates were detected on the surface of sphalerite particles floating to the CuPb final concentrate.At Matagami, significantly more isopropyl xanthate and isobutyl dithiophosphate were detected on sphalerite recovered to the Zn final concentrate, compared to sphalerite lost in the Zn rougher tails.In the Zn circuit of Kidd Creek, sphalerite lost to the tails had on average ten times less xanthate compared to sphalerite recovered into the Zn final concentrate. Xanthate was also detected on the floated pyrite particles. In addition to isobutyl xanthate, amyl xanthate was also detected on the floated sphalerite and pyrite particles.This preliminary investigation has (a) demonstrated the ability of TOF-SIMS to detect individual collectors on particle surfaces from plant samples and (b) shown that TOF- SIMS is an excellent tool, complimentary to TOF-LIMS, in establishing the surface chemistry of minerals as related to mineral processing."

Jan 1, 1995

By E. R. Landry

This paper reviews the current state of electric furnace technology, with emphasis on some of the more recent developments. A large section of the paper is devoted to the use of increasingly high power inputs by arc furnace operators. Operating practices are then covered, including some of the newer techniques which have been tried.

Jan 1, 1967

By Wouter Bleeker, Isabelle Cadieux

"Abstracts of theses related to mineral deposit studies and exploration, completed at geology or earth science departments of Canadian universities, have been compiled for the period 1991 to mid-I993. Part I, presented in the June, 1994 issue of the CIM Bulletin, gave a listing of thesis titles. Part II. which consists of edited abstracts of theses considered to be of direct application to mineral deposit studies and exploration. is presented under various themes as follows:A. Kimberlites, Other Alkaline Intrusions and Related Studies;B. Volcanogenic Massive Sulphide Deposits and Related Studies;C. Mineral Economics;D. Mesothermal Gold Deposits. Other Gold Deposits and Related Studies:E. Magmatic Nickel-Copper, Platinum Group Element and Chromite Deposits and Miscellaneous Platinum Group-related Studies;F. Granite and Pegmatite-related Deposits and Porphyry Deposits;G. Diverse Hydrothermal Deposit,>, Sediment-hosted CopperDeposits and Mississippi Valley Type Lead-Zinc Deposits; andH. Uranium-related studies, Evaporites and Exploration Geophysics.Abstracts related to themes A to F were presented in previous issues of the CIM Bulletin, abstracts related to themes G and H are presented in this issue.G. Diverse Hydrotbennal Deposits, Sedimenthosted Copper Deposits and Mississippi Valley Type Lead-Zinc Deposits"

Jan 1, 1995

By D. L. Johnston

"The avenues and degree of participation by aboriginals in the Canadian minerals industry have changed significantly during the thirty years of the author's career in that industry.The typical 1950s cycle of mineral industry involvement of a local non-Europeanized aboriginal was as an individual employee. The employment relationship would begin with the best of intentions by both parties of permanence and terminate when the pioneering employee was unable to reconcile the attendance behaviour required by the employer and the social-sharing behaviour demanded by family and friends.Cominco Ltd. has been a mine operator and developer in the North since the 1920s. Cominco's early experiences with employment of non-Europeanized natives at the Con Mine in Yellowknife, Northwest Territories from 1938 to 1986 was a negative experience from both the employee and employer ends. A series of classic failures in employment of individual aboriginals was a large part of the history. A few Metis or natives from other areas were the permanent aboriginal employees at Con (2010). Racial prejudice was overt on the street in Yellowknife and, it can be assumed, in the workplace, as well.The history of aboriginal employment at the Pine Point, Northwest Territories operation (1964 to 1988) was somewhat better but also frustrating. The mine was equidistant (80 km) from the Dene communities of the Hay River Indian Reserve and Fort Resolution, both on Great Slave Lake. Despite a large aboriginal presence and many well-intentioned efforts, employment of aboriginals at Pine Point never got much beyond ten per cent. These would have been half local and half northern prairie aboriginals. One continuing success story was the railcar loading and covering crew led by Ed McKay, a local aboriginal. This predominantly aboriginal crew did its own recruiting and several are on Cominco pension."

Jan 1, 1995