Search Documents

By S. Bozorgi, K. Anders

"The automotive applications of heat treatable AlCu cast alloys are designed for performance at high temperature, which can be improved using specially alloying element as well as different heat treatment. In this research work an effect of alloying element such as Cu, Ni and heat treatment on microstructures and mechanical properties of AlCu alloy were investigated using optical microscope (LIMI), scanning electronic microscope (SEM) equipped with energy dispersive X-ray detection (EDS), Differential scanning calorimetry (DSC) and mechanical testing. It was found that during solidification most of the elements Cu, Mg and Ni segregated at the grain boundaries in the form of Al2CuMg or Al7Cu4Ni and a very small part of Cu and Ni element dissolved in the FCC-Al matrix. The latter is not completely reclaimable for strengthening mechanisms in FCC-Al matrix in its as-cast state. The results of mechanical test show that yield strength and ultimate tensile strength increases after heat treatment significantly compared with the as-cast state. Furthermore the mechanical properties at elevates temperature (240°C) is higher with higher Cu+Ni+Si containing alloys compared with the less Cu+Ni+Si containing alloy.INTRODUCTION Due to the high strength-to-weight ratio, high strength and ductility at room- and elevated temperature, AlCuSi cast alloys are widely applied in the automotive industries specially for producing cylinder head and engine block, where modified alloys with enhanced metallurgical properties are always needed to satisfy the ever increasing demands for the applications. The AlCu based cast alloys can be strengthened by age hardening. The precipitation processes from which this hardening is derived can be attributed to the presence of selected trace element additions or micro alloying, which can change the process or kinetics of precipitation in age hardenable AlCu cast alloys (Polmear, 1998; Morris, 1991). Furthermore their strength is mainly controlled by the aging process through the precipitation and growth of very fine precipitates of the ?'-phase (a semi-coherent, metastable form of the equilibrium Al2Cu phase) from the Al and Cu Guinier-Preston (GP) zones. Several studies have shown that solute clustering occurs prior to the precipitation of GP zones, and this modifies both the nature and kinetics of the precipitation process. The typical size of GP zones is in the order of tens of nanometers, and the chemical composition of these precipitates is not easily measured, even with a typically analytical electron microscope (Polmear, 1989)."

Jan 1, 2018

By G. Zárate, G. Tapia

Anglo American Chile has been doing copper concentrate leaching studies at the laboratory and small pilot plant scale since 1992. Among the processes evaluated are bacterial leaching and pressure leaching using Mantos Blancos, Salobo Project and Quellaveco Project concentrates. Late in the nineties, it was decided to focus the research on pressure leaching, either medium or total pressure oxidation. Preliminary scouting tests were run with Mantos Blancos concentrate samples during 2000, which were repeated during 2003 together with samples of Los Bronces and El Soldado concentrates, in order to define the most suitable concentrate for running a pilot plant campaign at AARL, which was carried out in two campaigns, a first one from November 2003 through January 2004 and a second one during April 2004. Mantos Blancos was the selected concentrate and the laboratory and pilot plant results are discussed in this paper together with some preliminary economic estimates.

Jan 1, 2004

By Denis Beaudoin

Program Basics: Goals, Course Content & Training Process Sudbury: History of the Program & Lessons Learned Diavik: History of the Program & Lessons Learned Most Recent Program: Totten Mine in partnership with Sagamok Anishnabek Summary -Lessons Learned Conclusion

Oct 1, 2010

By M. A. Clayton, D. Kinakin

The Mitchell Creek Landslide is a large, structurally controlled, complex bedrock instability located in northwestern British Columbia. Characterization of the landslide using aerial photograph, exploration geology, and geotechnical investigation data has been completed allowing the development of a three dimensional conceptual model of the landslide domains and slope behaviour. Three domains have been identified in the landslide, from top to bottom: the Sliding domain, a relatively intact slab slowly sliding into the valley; the Transition domain, located in the mid slope of the landslide and showing evidence of significant extension and continuing to subside and displace into the valley; and a Toppling domain, at the toe of the landslide in an area of overturned foliation. Movement is greatest in the Toppling domain, with long term estimated rates of movement up to 4 times that of the Sliding domain; the Transition domain exhibits the greatest range of displacement rates, with average long term values approximately double the slower Sliding domain. This paper documents the results of numerical modelling of the Mitchell Creek Landslide with variation in geomechanical properties, basal rupture surface configuration, structural fabric, and pore water pressure conditions. The locations of internal shear surfaces within the landslide have been estimated from surface scarps, structural fabric orientation, and borehole monitoring data. The performance of each numerical model was evaluated against observed behaviour of the landslide. The configuration and properties of the basal rupture surface were identified as critical to model behaviour, as was spacing and location of internal structures.

Jan 1, 2015

By E. J. Marcotte

"INCO LIMITED'S Shebandowan Mine and Mill is located in a scenic tourist and cottage area near the western tip of Lower Shebandowan Lake, approximately 90 Km west of Thunder Bay, Ontario. This nicely designed complex is a positive indication that mining operations can co-exist in harmony within the natural environment.The Shebandowan complex processed nickel-copper ore from 1973 to 1985, inclusive, after which operations were shut down.In late 1988, INCO LIMITED decided to place the Shebandowan complex back into operation, under contract, to mine and mill the remainder of the ore body, according to their specifications. MaclSAAC'S EXPLORATIONS was the successful bidder for the project. Following preliminary rehabilitation, operations were re-activated in late March, 1989. The ore mined to date is of a moderately lower nickel grade than the majority of previous years. However, a higher tonnage rate, combined with improved nickel recoveries, has contributed to a viable operation.A series of mill operating and equipment modifications has enabled MaclSAAC EXPLORATIONS to achieve the quality and grade of nickel-copper concentrates specified, and at the same time, expand mill tonnage throughput while attaining increased nickel recovenes."

Jan 1, 1992

By G. P. Kundargi

India is one of the fastest growing economies in the world. The role of the Iron & Steel industry is very important for the development of the country. Iron and steel are among the most important components required for the infrastructure development of the country. This is one of the fastest growing sectors. The demand drivers for the Indian Iron & Steel industry are increase in the activities of the manufacturing industry and infrastructure development. Indian Iron & Steel industry with its strong forward and backward linkages contributes significantly to overall growth and development of the economy. The industry today directly contributes 2% of India?s Gross Domestic Product and its weightage in the official Index of Industrial Production (IIP) is 6.2%. Manganese is a main ingredient for production of steel. Almost 90% manganese is being utilized by the steel industry worldwide. Globally, there is no substitute for manganese as on date. There is huge gap between demand and production of manganese ore in the country. To meet this demand gap and to support for growth of national economy, MOIL Limited (formerly Manganese Ore India Limited), a Government Enterprises, producing annually around 1.1 million tonnes (mt) of manganese ore and value added products, has geared up with various infrastructural activities to increase the present production capacity of 1.1?1.5 mt in 2016?2017 and 2.2 mt in 2020?2021. The paper deals with the technological improvements and infrastructural development activities of MOIL; this will help MOIL to become the market leader in manganese ore production globally in the coming years.

Aug 1, 2013

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016

By Mosquera. J.

Tailings Storage Facilities (TSFs) are vast structures that respond to site-specific characteristics, rate of production, placement techniques, and the physical and mechanical properties of tailings. As a common denominator, TSFs are in some degree vulnerable to failure due to liquefaction, poor management, slope instability and/or unusual climatic events. In practice, stability of TSFS is determined by calculating a minimum Factor of Safety (FOS) using the Limit Equilibrium Method (LEM). However, it has been proven that relying exclusively on the limit equilibrium approach is not accurate because it is basically a static method that does not take into account the stress-strain distribution and displacement experienced by the constitutive materials of a TSF. In order to overcome these limitations of the LEM, the finite element method - Shear Reduction Technique (SRT) has been used as a more reliable tool for TSFs stability assessment. This paper presents a comparative stability analysis between an upstream tailings storage facility (UTSF), and a water retention tailings dam (WRTD) under static and pseudo-static states using simplified and rigorous LEMs and the SRT. Additionally, and taking into consideration the intrinsic uncertainty of tailings properties, sensitivity and probabilistic analyses in the form of Monte Carlo Simulation (MCS) and the Point Estimate Method (PEM) are applied to determine the Probability of Failure (Pf) and Reliability Index (ß) of each TSF. It is shown that the friction angle of UTSF?s foundation and the core?s cohesion of the WRTD are the main variables that govern stability. Further analysis shows that the WRTD has a higher reliability index and a lower probability of failure than the UTSF.

Aug 1, 2013

By R. P. van Hille, N. Mooruth

Remediation of acid rock drainage (ARD) was performed within a linear flow channel reactor (LFCR) via a floating sulphur biofilm (FSB). A full sulphur species material balance was conducted in order to characterize the sulphide oxidation. The reactor was able to achieve an 82% and 93% conversion of sulphide with a hydraulic residence time of 2 and 5 days respectively. 92% and 55.5% of the converted sulphide reported to the biofilm as sulphur for the 2 and 5 day residence times respectively. The mass transport limitations within the biofilm were identified via a dissolved oxygen gradient profiling system.

Jan 1, 2011

By Akihiko Nishiyama

Unmanned construction technology used for remote control operation of construction machines has some problems to solve compared with manned operation of construction machines, such as fatigue due to long-term operation or decreases in operational efficiency. To solve these problems, we recorded the viewpoints of operators in both manned and remote control operation and analyzed the differences. This paper reports on our discussion of improving the operability of remote control operation based on the analysis results.

Aug 1, 2013

By Fritz F. Prugger

In August, 1970, during routine shaft grouting, a major water source was intersected. Water and quicksand under very high pressure entered the shaft at a rate of 65 m3 per minute. The mine and both shafts were flooded. The breach was sealed simultaneously from within the shaft and through a relief hole drilled from surface. The mine was dewatered, rehabilitated and the equipment was restored. Production resumed two years after the accident.

Jan 1, 1979

By P. Chryssanthakis

"The aim of this study is to give a better understanding for the behaviour of the composite material RRS and the synergy effect of its components while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10 m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. The newest part of the lower part of the Q-chart gives more information on required support compared to older Q-system versions. The RRS can be described as a three part composite material with the 3rd component being the reinforced concrete beam (with no fibers) and with steel rebars that are placed in groups and sprayed with pneumatically applied shotcrete in layers. The RRS usually have a total thickness varying between 0.20 and 0.50 m and a width between 0.25 and 0.60 m respectively. They are placed at different distances along the tunnel axis depending on the rock mass quality.In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. This was done by writing a FISH subroutine which is implemented in the discontinuous numerical code Universal Distinct Element Code (UDEC) that takes into account the characteristics of the reinforced beam (height, width, number of steel rebars, and spacing) in the calculation process. A rather extensive parametric study has been run by using the same key input rock mass parameters and in situ stresses (?H/?v = 0.5), and changing only the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam.The results show that: a) the S(fr) is almost overloaded in the first 4 hours after application in both tunnels; b) on the S(fr) and steel rebars, the stresses, axial and shear loads, as well as moments are decreasing after 16 hours and 28 days; and c) the bolts loads are increasing with time. The observed reduction in stresses and loads in both the S(fr) and reinforced beam is surprising. A possible explanation is that tunnel arches are self-supported to a lesser extent as time progresses due to redistribution of stresses in the nearby rock mass through the radial bolts. The loads in radial bolts are increasing by almost 25%. This can be seen from the overall results as we observe an increase in maximum principal stresses, displacements, shear displacements along joints and hydraulic apertures compared to tunnel baseline that has no support of any kind."

Jan 1, 2015

By C. H. Lau, I. T. Ng

Uniaxial Compressive Strength (UCS) of rocks is an important mechanical parameter for many civil engineering and rock engineering applications such as tunnel excavation, slope stability and foundation design. Macau is one of the world's fastest growing and most densely populated cities, many large and important infrastructures have been being continuously built using pile foundations which are designed to be supported by granitic bedrock. In Macau, the UCS of the granitic bedrock is required almost for every project involving pile foundations and is always measured directly from UCS test in the laboratory. However, direct measurement of UCS requires high quality rock core sample which is not only time-consuming and expensive but also requires high level of operating skill. In view of this fact, estimation of UCS using some empirical correlations will be more practical and efficient because they are relatively fast and economical compared to the direct measurement from UCS test. In the past, some empirical correlations had been established and widely used for estimating UCS of rocks in common engineering practice. However, it has been well recognized that the rock properties are generally varied with sites or geological regions in other words an empirical correlation developed from one region or one country may not be applicable for other regions or countries. Due to the reason that the empirical correlations for predicting UCS for granite are scarce in practice, in this study an extensive experimental program has been performed and a large database containing data such as UCS, Point Load Index (Is50), Schmidt Rebound Hardness (RL), porosity (?), water absorption (S), specific gravity (Gs) and dry density (?d) has been developed. An attempt has been made for developing a new empirical correlation for estimating the UCS of Macau granite. Accordingly, a comprehensive statistical analysis for correlating UCS with Is50, RL, ?, S, Gs and ?d has been performed and a local empirical relationship based on the developed database is proposed for obtaining reliable estimation of UCS for the granite of Macau. Finally, the performance of the proposed correlation is accessed by using another independent testing database developed in this study. It indicates that Is50, RL, ? and S have strong correlation with UCS whereas Gs, ?d have poor correlation with UCS. This study not only proposed a proper predictive empirical correlation for UCS determination for Macau granite but also provides detailed statistical information which is beneficial to engineers for obtaining better characterization of Macau granite.

Jan 1, 2015

By K. A. Natarajan, M. N. Chandraprabha

Selective separation of minerals from complex sulphide ores is a challenging task and it is often difficult to get commercially acceptable individual concentrates by conventional selective flotation using inorganic collector reagents. Microbially-induced mineral beneficiation has proved to be more effective, economically viable and an environmentally benign process for the effective separation of various minerals. Applications of microbially-induced mineral beneficiation are demonstrated in this paper with respect to beneficiation of complex multimetal sulfides. The role of adapted microorganisms and bioreagents in the beneficiation of complex sulphide minerals are also illustrated.

Jan 1, 2009

By Matthew Novak, J. Brent Hiskey

It is well known that when chalcopyrite is put in direct contact with copper in an acidic medium a galvanic cell is created. Chalcopyrite is reduced to iron and sulfur deficient defect phases such as bornite, chalcocite, and at very low potentials to elemental copper. Galvanic conversion experiments were performed using three chalcopyrite concentrates. The first chalcopyrite contained less than 10% impurity phases. The second concentrate had a high concentration of pyrite, and the third concentrate had a high concentration of pyrrhotite. The effect of temperature, acid concentration, chalcopyrite grain size, copper grain size, and agitation on the rate of chalcopyrite conversion was studied.

Jan 1, 2014

By André Piché

"Over the last ten years, several developments have been undertaken to conceive a machine capable of carrying out simultaneously all the mining tasks in hard rock deposits: cutting, mucking, hauling, ground support and dust control.The main advantages of continuous mining over conventional drill and blast is the elimination of the cyclical nature of the actual methods. Other advantages sought are improved stability of mine openings, higher productivity, lower costs, and a cleaner and safer mining environment. Noranda has con-tributed to these developments in a major way. As a member of HDRK, Noranda participated in the development of two mechanical continuous mining machines; the TM60 and the Wirth. Noranda also undertook a development of its own based on the utilization of electricity to break rock. This technology is called plasma blasting (PBT). The concept of plasma blasting is illustrated in Figure 1.When the operating voltage is reached (18kV), the energy is released through a high current switch (500k A) into a coaxial powercable. It is then delivered to the tip of an electrode inserted into a drill hole which is filled with an electrolyte (water). When the energy reaches the electrolyte, it is instantaneously transformed into a high temperature, high pres-sure plasma that produces a shock wave capable of breaking rock(1).After initial testing of the plasma blasting technology in the lab and in the feld, two experimental platforms were constructed. The first one, a test bench, was erected at the Noranda Technology Centre in Pointe Claire, Quebec.(2)The second one is a rock breaker prototype based on a standard diesel-powered carrier (Fig. 2). Each platform was equipped with a 300 kJ pulsed-power module.In 1993, the rock breaker prototype was used for an extensive series of tests in the field. During that campaign, over 700 oversized boulders were blasted. The results of the tests demonstrated that more durable components for PBT were needed. The test bench was then used to successfully develop and test long-lasting components (probe, switch, cable, connector) that can be adapted to industrial platforms leading to the commercialization of the technology."

Jan 1, 1996

By J. Bigu, M. G. Grenier, S. Hardcastle

"This study was undertaken in a belt conveyor drift of an underground hard rock mine. The conveyor transported ore or waste from a crushing operation located upwind from the drift sampling locations. A 250 m section of this drift was selected and several types of measurements were taken. Average respirable concentrations in the drift were 0.43 mg/m3 and 0.19 mg/m3 for total and silica dust, respectively. From the respirable dust concentration profile along the drift, it may be possible to estimate the contribution from extended sources such as dust produced by the belt and return idlers.The airborne dust in the drift had an average mass-median aerodynamic diameter of 4.2 micron. A continuous dust monitor showed that the crushing operation produced fairly high dust concentrations (sometimes greater than 4 mg/m3) over short periods of time.IntroductionAirborne dust in the respirable range is known to be the cause of various forms of lung ailments . In underground mines, respirable dust sources are created at many stages of production. All mining operators are responsible for de signing and establishing means of reducing airborne dust. In some cases, sources of dust are well defined and suppression methods are standard.In the case of interest here, the airborne dust cloud was formed from the contribution from many sources, which may be either discrete or extended. At the experimental site, the discrete or point sources were the crushing operation and the belt conveyor transfer point (tail pulley). These sources may be controlled by proper dust capture and scrubbing systems as well as dilution ventilation. Examples of extended dust sources in the area include dust produced by the re-entrainment of settled particles along the drift. Ventilation air movement and vehicular traffic both contribute to this phenomenon. Dust produced by the conveyor is another example of an extended dust source. Caked deposits on the return strand and idlers as well as the transportation of dry material on the belt, can be major contributors. Proper wetting of roadways and muck as well as proper belt cleaning techniques can help reduce these emissions. The cleaning apparatus, used on the belt where these experiments were conducted, is shown in Figure I. These and other belt cleaning techniques are described in more detail elsewhere."

Jan 1, 1987

By J. Etcheverry, E. Seguel, R. Díaz, F. Parada, R. Parra, E. Balladares

A thermodynamic and kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite during partial roasting of enargite-containing copper concentrates. The proposed mechanism involves solid-solid-gas and solid-gas reactions between chalcocite, pyrrhotite, gaseous sulfur and oxygen. The formation of bornite could be explained by a two-step reaction: the first one involving the formation of chalcopyrite by a reaction between Cu2S, FeS and gaseous sulfur, followed by a second step in which the newly formed chalcopyrite reacts with additional chalcocite to form bornite. Although thermodynamically the direct formation of bornite is more favorable than that of chalcopyrite, the lower diffusion kinetics of bornite formation could explain the preferential formation of chalcopyrite. If the reaction occurs with stoichiometric chalcocite and pyrrhotite in the presence of gaseous sulfur to form chalcopyrite, no bornite is formed, while for the stoichiometric reaction between chalcopyrite and chalcocite in the absence of sulfur, only bornite is formed. For the formation of magnetite and chalcopyrite the mechanism could involve the partial reaction of chalcocite and pyrrhotite in the presence of oxygen. The proposed model is thermodynamically consistent with the experimental results obtained in laboratory and pilot plant. INTRODUCTION The processing of high-arsenic copper concentrates with over 0.7 wt.-% arsenic by conventional smelting-converting normally require an additional arsenic removal step to reduce arsenic content to levels below 0.2–0.3%. One of these high-arsenic copper concentrates is the one produced by the Ministro Hales Division (DMH) of CODELCO, which has the typical chemical composition shown in Table 1. Enargite (Cu3AsS4), chalcocite (Cu2S) and pyrite (FeS2) are the main mineralogical species present in these concentrates, with over 75 wt.-%, as shown in Table 2. Partial or “neutral” roasting of these concentrates under controlled temperature and partial oxygen pressure conditions at 923–993K (650–720ºC) can remove up to 95% of the arsenic as As2S3 (As4S6), which has a high vapor pressure under these conditions, leaving a calcine with low residual arsenic. In copper concentrates, arsenic is present generally as enargite and arsenopyrite. This compounds as well as others such as pyrite and covelite, decompose readily above 770 K (500ºC), releasing, in addition to gaseous arsenic trisulfide, gaseous sulfur which by oxidizing to SO2 generates most of the heat required by the process.

Jan 1, 2019

"The Companion Policy is guidance and not law. It sets out the views of the Canadian Securities Administrators (CSA) at to the manner in which the CSA interprets and applies certain provisions of NI 43-101 and Form 43101F1. The Companion Policy references the CIM Best Practice Guidelines for Mineral Exploration, and the Mineral Resources and Mineral Reserves, and that they should be followed by Qualified Persons.COMPANION POLICY 43-101CP TO NATIONAL INSTRUMENT 43-101 STANDARDS OF DISCLOSURE FOR MINERAL PROJECTS This companion policy sets out the views of the Canadian Securities Administrators (the “CSA”) as to the manner in which the CSA interprets and applies certain provisions of National Instrument 43-101 and Form 43-101F1 (the “Instrument”), and how the securities regulatory authorities or regulators (the “Securities Regulatory Authorities”) may exercise their discretion in respect of certain applications for exemption from provisions of the Instrument. PART 1 APPLICATION AND TERMINOLOGY 1.1 Supplements Other Requirements – The Instrument supplements other continuous disclosure requirements of securities legislation that apply to reporting issuers in all business sectors. 1.2 Evolving Industry Standards and Modifications to the Instrument- Mining industry practice and professional standards are evolving in Canada and internationally. The Securities Regulatory Authorities will monitor developments in these fields and will solicit and consider recommendations from their staff and external advisers as to whether modifications to the Instrument are appropriate. 1.3 Application of the Instrument -The definition of “disclosure” under the Instrument includes oral and written disclosure. The Instrument establishes standards for disclosure of scientific and technical information regarding mineral projects and requires that the disclosure be based on a technical report or other information prepared byor under the supervision of a qualified person. The Instrument does not apply to disclosure concerning petroleum, natural gas, bituminous sands or shales, groundwater, coal bed methane or other substances that do not fall within the meaning of the term “mineral project” in section 1.1 of the Instrument. 1.4 Mineral Resources and Mineral Reserves Definitions - The Instrument incorporates by reference the definitions and categories of mineral resources and mineral reserves as set out in the Canadian Institute of Mining, Metallurgy and Petroleum (the “CIM”) Definition Standards on Mineral Resources and Mineral Reserves (the “CIM Definition Standards”) adopted by the CIM Council on November 14, 2004, as amended. 1.5 Best Practices Guidelines for Mineral Resources and Mineral Reserves - A qualified person classifying a mineral deposit as a mineral resource or mineral reserve should follow the CIM Estimation of Mineral Resources and Mineral Reserves Best Practice Guidelines adopted by CIM on November 23, 2003, as amended. These guidelines are posted on www.cim.org."

Jan 1, 2003

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998