Search Documents

By A. Lam

The use of a liquid fed direct methanol fuel cell (DMFC) as a power source for micro and small portable applications is attractive due to its system simplicity, low temperature, etc. The aqueous methanol is directly oxidized and does not require additional fuel processing steps as in reformate based PEM fuel cells. In addition, the use of a liquid fuel is advantageous with respect to humidification, stack cooling and system energy density. The DMFC however, has technological issues that must be addressed before it can be widely adopted, particularly in larger applications such as small utility and transportation. At present, the crossover of methanol from the anode to the cathode is a major limitation on DMFC performance and fuel utilization efficiency. In this paper we discuss the influence of fuel modification on the control of crossover. This involves the use of different fuel additives and concentrations to minimize crossover. This appears to be the first reported case of the use of fuel modification (additives) to reduce methanol crossover. The rate of methanol permeation under passive conditions is discussed with respect to the different conditions.

Jan 1, 2005

By J. R. Gill

Introduction The property and plant of the Falconbridge Nickel Mines, Limited, is situated about 13 miles northeast from Sudbury, in Falconbridge township, near the eastern extremity of the southern Nickel Range. As early as 1899 or 1900 some work was clone on this property by the late Thos. A. Edison, when a shaft was sunk through 80 feet of overburden to within a few feet of the ore-body. At this point quicksand was encountered, which made it impossible to continue with the equipment at hand. As a result, the activities of the Edison party ceased in this section. There was no further progress until 1915 and 1916, when an extensive diamond-drilling campaign, carried out by the E. J. Longyear Company, located the ore-body that is now being worked. The property was acquired by the present operators in 1928, and in September of that year active mining development was commenced. Features Influencing Design Of Plant Early in 1929 plans were prepared for a smelter and the necessary crushing and sorting plant. In spite of the general trend towards the reverberatory furnace as a smelting unit, it was decided to erect a blast-furnace plant. The limited tonnage to be treated, of course, influenced this decision to a great extent. However, it was known that, with the proper procedure, extremely favourable results, both economic and metallurgical, could be obtained in blast furnace smelting. The possibility of very low slag losses, the simplicity of operation by the elimination of roasting plant, fuel plant, etc., the ability to handle coarse feed, and the lower initial cost, were considered factors in favour of the blast furnace. Notwithstanding the fact that we might be called on to treat a certain amount of concentrate, it appeared that the blast furnace was the proper unit for the contemplated operation.

Jan 1, 1932

By B. Friedrich, N. Anastasijevic, S. Stopic

The extraction of nickel from Serbian and Western Australian lateritic ore by sulphuric pressure acid leaching (PAL) has been studied. The following parameters were tested: stirring rate, acid to ore ratio, reaction time, pressure and temperature. These studies were performed with ore samples from the Rudjinci, Serbia and Silcrete, Australia, both belonging to the laterite-silicate group of deposits. An increase of the reaction temperature and the stirring speed at a fixed acid/ore ratio showed a positive influence on nickel extraction. The decrease of the oxidation potential with time correlated with the increase in Fe(II) in solution and nickel extraction as the reaction went to completion for both ores. The target values of 95 % Ni extraction and 60 % Co extraction were attained in 5 min at 250°C for the Serbian silicate ore, at an agitation rate of 1500 rpm, 10 % solids, and acid/ore ratio of 0.40. Under similar conditions only 60 % Ni, but 69 % Co could be extracted from the Australian Silcrcte ore due to different mineralogy. The nickel extraction was shown follow a diffusion-controlled reaction model.

Jan 1, 2004

By I. M. R. Duarte, J. A. Rodrigues-Carvalho, F. R. S. Rosa, A. B. Pinho

"This paper aims to contribute to the knowledge of the mechanical properties of the shales and greywackes which constitute the flysch-type deposits of the Baixo Alentejo Flysch Group, in the south of Portugal. These formations are flysch-type deposits constituted by sequences of usually thick greywacke beds alternating with thin shale beds, which include sometimes intercalations of conglomerate beds. All the sedimentation of these flysch formations was controlled by tectonics. At the same time, should have occurred along with the first Hercynian deformation phase, a low-grade metamorphic event (chlorite zone), that affected these flysch deposits. This study highlights the influence of anisotropy and heterogeneity of these flysch rocks on their physical and mechanical characteristics. The anisotropy verified in some physical properties and on mechanical properties, due to the foliation makes difficult the sample preparation for the laboratory tests. Besides, it induces a scattering of the properties values measured, as for example, the strength and the deformability. The heterogeneity is related to the main features of these geological formations, which are constituted mostly by thinly stratified greywackes and shale beds, which sometimes may affect the results of the laboratory tests making them less representative. The study is made by using both shales and greywackes that constitute these flysch-type deposits in order to evaluate their geotechnical properties, mainly of the shales. Samples of these two rock materials, are tested accordingly a laboratory testing programme, which includes which included mineralogical analysis (X-ray diffraction), physical tests (bulk density, porosity, and void index) and mechanical tests (uniaxial compression, and deformability tests). INTRODUCTIONOne of the factors that most influence the geomechanical behavior of rocks, as well as rock masses is the anisotropy. The word anisotropy comes from two Greek words ""anisos"" (meaning uneven) and ""tropos"" (meaning direction). A body or material is considered to be anisotropic, where the same property has different values depending in which direction it is measured, therefore, an anisotropic material is one whose magnitude of the properties depends on the direction in which these are studied or measured. Otherwise, it is about an isotropic material. However, the fully isotropic materials are quite rare in nature."

Jan 1, 2015

By G. A. Vissac

In this paper we intend to deal particularly with the economic side of coal washing as it applies to our mines. We will then discuss why the dry-cleaning process has been selected, and give a brief description of our plant, dwelling only on its specific features and referring the reader to the numerous papers published on the subject for any details on the principles and machinery used in dry cleaning. ECONOMIC DISCUSSION The washery introduces an extra cost for depreciation, operation, and loss in treatment. A certain proportion of the coal, now being sold, and which the miners have been paid for. will have to be wasted. As a whole, the total increase in cost would be approximately 60 cents per ton. On the possibility of recovering this amount depends the success of the washery. There are two advantages to be expected from the washery, the first, which occurs at the mine and which will be certain; the second, more difficult to estimate, because it depends upon convincing our customers that they should pay more for a better product.

Jan 1, 1924

By William G. Pariseau

"This contribution describes linkage of stress concentration at the face of tabular excavations, for example, longwall coal mine panels, at a meter scale to surface subsidence at a kilometer scale. Joints are considered according to orientation and spacing at an intermediate scale. A new dual-node, dual-mesh technique based on first principles uses a multi-scale technique that allows for computing whole mine surface subsidence while also allowing for computational details of stress, strain and displacement about main entries and pillars, panel entries, and bleeder entries. The technique is implemented in a conventional continuous Galerkin finite element program that has been in use for many years.The advantage of the dual-node, dual-mesh technique is the capability to do a whole mine analysis that takes into account interaction between all sections of a mine where stress transfer over long distances is often the rule rather than the exception while at the same time allowing for details of stress concentration at working faces where caving is initiated and subsidence begins. The technique, outlined recently during ARMA 2014 (Pariseau, 2014), is applied to an underground coal mine in central Utah where mines are developed from outcrops in steep canyon walls. Meshes contain over 10 million, three-dimensional nodes; runtimes are typically overnight, as a practical matter. Results compare favorably with mine subsidence measurements made over a period of several years and show the capability of this new technique to provide useful design guidance for tabular deposits such as underground coal mines. The role of variability or uncertainty in strata properties is illustrated in element safety factor distributions about development, bleeder and main entries and pillars. Such details are new in this contribution. Energy tracking for mine-induced seismicity is also new. Results show a high correlation between number of events and failed elements and suggest a simple index to mine induced seismicity."

Jan 1, 2015

By Brian W. Mackenkzie, Jozef Lajzerowicz

This paper is intended to familiarize planners in the noncommunist world with the district planning approach used in eastern Europe for mining development. It deals generally with the basic nature of the district planning problem, the planning process for mining development and the state organization for the planning of mining districts. A number of applications of district planning techniques to both established and new eastern European mining districts are described.

Jan 1, 1971

By Amir Asadi

Various damage modes that evolve with time in polymer composite laminates, such as transverse cracking, vertical cracking, delamination, and fiber fracture, as well as the interaction among them, influence the time-dependent degradation in modulus (creep) and strength (creep rupture) of polymer composite laminates. This study is focused on modeling the time-dependent evolution of transverse cracking in [90] plies of a multidirectional polymer composite laminate [0m/190n]. This model uses a two-dimensional variational analysis to determine the stress state at any given creep time. The elastic stored energy, determined using this stress state, is compared with a critical energy for fracture to determine the crack evolution with creep time. Model predictions are compared with experimental results to validate the model.

Jan 1, 2010

By A. Tabereaux

The reduction of perfluorocarbon (PFC) emissions from aluminum electrolytic cells is a key issue in reducing greenhouse gases at all aluminum smelters, The emission of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) gases during anode effects at smelters can be calculated using two different methods; anode effect-minutes slope and anode effect overvoltage, This work demonstrates that the optimum method depends to a large extent on the type of anode effect kill algorithm utilized at each smelter, CF4 emissions vary widely from aluminum cells depending on the type of anode effect kill method utilized; fast, aggressive anode bridge movements vs. slower, moderate anode bridge movements.

Jan 1, 2005

By Robert A. MacGregor

"Following several months of test work, water leaching in mined-out areas at Stanrock commenced on a production basis in February, 1963. A combination of fast high-pres-sure washing and rewashing of stopes on a predetermined cycle, and the intermittent sprinkling of low-grade heaps, using both fresh water and recirculated acid water, has proved most successful. There was also a correlation of daily sampling data points to a relationship between the leach water grade and the grade of the material being washed, the leaching time and the location along the dip. An increasing tolerance for uranium by the acid-producing bacteria is also indicated. A steady production rate of 10,000 to 12,000 lbs. of u.08 per month is being maintained, with an over-all mine water grade of 0.25 lb. per ton and a pH of 2.3."

Jan 1, 1966

By Syamujulu. M

Subsequent to the unbundling of the Zambia Consolidated Copper Mines (ZCCM) and the privatization of its constituent parts, the Konkola Copper Mines (KCM) represents a third of the original conglomerate. Now run by private hands as a sub group of Vedanta Resources Plc of India, KCM is strategizing on how best to deal with the operational issues of the organisation to resolve some of the difficult, logistical, environmental, mineralogical and metallurgical problems being encountered to tum them into opportunities as the company turns around. This paper reviews the options being put in place to provide appropriate solutions and strategies including the treatment of the highly siliceous low energy copper belt concentrates in its mining operations in Zambia.

Jan 1, 2007

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By R. J. A. Fricker

IT is the purpose of this essay to give a reasonably complete description of shaft sinking under a rock pentice in a small Northern Ontario gold property. Hallnor is in many ways an exceptional mine, but the sinking operations here described are but typical examples of the excellent practice for which Canadian mines and mining engineers are justly famous the world over. The worth of the subject lies, therefore, nor in its originality, but in its soundness; not in the spectacular, but in the economical and safe. Attention is particularly drawn to the excellent safety record and to the exceptionally low overall sinking cost. INTRODUCTION Prior to April, 1939, the Hallnor No. 1 shaft had been sunk vertically to a depth of 997 feet below the surface. It is a three-compartment shaft, 19 ft. 10 in. by 7ft. 7 in. outside the timbers (see Figure 1).

Jan 1, 1941

By M. Bouchard et G. Martineau

In the Chibougamau area, a large portion of the glacially tranported boulders which were deposited at the surface were later partly remobilized by the waters of Glacial Lake Ojibway. In the dispersal studies of these boulders, it is sometimes difficult to discern the effect of this reworking process. In addition, depositional processes in the lake contributed material to the original block deposits through the formation of boulder lag by littoral wave action and through direct sedimentation in the form of deltaic deposits. In spite of these complicating factors, dispersal studies at carefully selected sites which were unaffected by the above processes make it possible to unravel the general patern of glacial dispersion. In this study, indicator lithologies of the Albanel and Chibougamau formations were used. They give a coherent image of dispersal throughout the area showing transport toward the southwest. Considering the particular geological context of the region, and in view of the extensive mineral exploration studies which are being carried out, the results of this study are encouraging for the tracing of source areas of glacially transported mineralized boulders.

Jan 1, 1984

By J. Lu, J. B. Wiskel, D. G. Ivey, E. Niemi, H. Henein

Simulated TMCP using a Gleeble was undertaken to evaluate the effect of the austenite to ferrite cooling rate, coiling temperatures of either 400°C or 500°C and the magnitude of plastic deformation at the coiling temperature on the hardness of a Grade 483 (X70) steel. For comparable apparent cooling rates and deformation conditions, the hardness of the samples were independent of coiling temperature The application of a minimum compressive deformation > 8% was required to increase hardness at both simulated coiling temperatures of 400°C and 500°C. An increase in hardness was also observed with increased cooling times between 800°C and 500°C (i.e., slower cooling rates).

Jan 1, 2005

By Eiichiro Mizushima

Catalyst systems comprising (Ph3P)AuCH3 and acid co-catalysts were found to be highly efficient for hydration of alkynes to give ketones. Methanol was the best choice of solvents. Introduction Hydration of carbon-carbon unsaturated bonds is one of the environmentally benign routes to the carbon-oxygen bond formation. Hydration of alkynes forming carbonyl compounds, an important variation in this category, is a well known reaction which has been extensively studied. The reaction by acid-catalysis is the most conventional method, while it is applicable only to electron rich acetylenes to obtain satisfactory yields (1,2). The hydration of simple alkynes usually requires another catalyst (co-catalyst), typically a mercury(II) salt (3), which is inconsistent with the guiding principle of Green Chemistry (4).

Oct 1, 2003

By H. W. Smith, R. D. Fournier

This paper presents the results of an investigation of a full-scale rod mill. Appropriate numerical techniques are developed for the experimental determination of the parameters of a dynamic mathematical model from steady state data. The results confirm that this full-scale rod mill behaves similarly to laboratory-scale ball mills for which results have previously been obtained. It is noted, however, that although the model presented is adequate for predicting over-all particle size distributions, the size distributions of individual components of a multicomponent ore cannot be predicted.

Jan 1, 1972

By Bian Xue, Wu Wenyuan

High quality, mono-dispersed, hollow CeO2 microspheres with high surface area were produced by a spray pyrolysis method at 700oC. CeCl3 was used as the raw material of the process rather than Ce(NO3)3 because the latter is relatively difficult to obtain in industrial quantities. X-ray diffraction and electron microscopy results confirm the high quality synthesis of hollow CeO2 microspheres with narrow size distribution, good mono-disperse, and good reproducibility. The process of the formation of mono-dispersive CeO2 microspheres was investigated by chemical dynamics and a possible mechanism is proposed. This simple method for synthesis of CeO2 microspheres is easily scaled up to fabricate other metal oxide nanostructured materials at industrial scale.

Jan 1, 2014

By J. P. Nicoud

"The Frog's Leg project is located in the Kundana mining centre 22 kms West of Kalgoorlie, in Western Australia. The Mines and Resources Australia (MRA) Dioro Exploration Joint Venture has had considerable exploration success centred on the high grade Frog's Leg discovery. A gold resource of 930,000 ounces has been defined. At Frog's Leg there have been three discrete resource domains recognised - Supergene, Contact, and Quartz Lodes. This paper describes the metallurgical test work undertaken.The selection of the drill core was a joint effort by the MRA Senior Geologist and Mineral Engineering Technical Services (METS) to ensure the samples were representative of the ore body. Optimisation of gold recovery was essential as both the Contact and Quartz Lodes have exceptionally high percentages of free gold as well as significantly higher grades than the typical open pit ores found in Western Australia. The metallurgical scope of work included documenting all of the metallurgical test results, establishing the comminution characteristics, determining the percentage of gravity recoverable gold, evaluating the cyanide leach characteristics and determining the tailings characteristics. These studies were used as the basis of flow sheet design to treat both ores and to discuss the advantages and disadvantages of alternative flowsheets. Investigations also included toll milling options at various plants as well as second hand and transportable plants. Considerable technical effort has been put into ore characterisation by way of test work aimed at managing the process risk at each stage of project development, including mitigation. MRA also carried out detailed mineralogical analysis of the ores."

Jan 1, 2005

By J. Muralha, L. Lamas

"Given the results of triaixial tests, regressions are commonly used to evaluate the parameters of failure criteria that model intact rock strength and to perform statistical inferences used to evaluate characteristic values defined in EC7. Statistical robustness of these inferences is affected if the basic hypothesis underlying regression are not met, namely homoscedasticity (constant variance of the errors). This paper presents analyses of 23 sets of triaxial tests, starting by the evaluation of the regression parameters of the Mohr-Coulomb linear criterion and of the Hoek-Brown non-linear criterion, followed by carrying several statistical tests to check the homoscedasticity null hypothesis of independence between the variance of intact rock strength and the confining stress.INTRODUCTIONThough rock engineering design is clearly included in the scope of Eurocode 7(EN1997-1), its implementation raised a wide discussion regarding the applicability of structural safety concepts to geotechnical design of construction works in or on rock masses. The basis of the limit state design philosophy adopted in EC7 is that, for each particular design situation, all the possible limit states for a structure, or part of it, shall be considered and that it shall be demonstrated that the likelihood of any limit state being exceeded is sufficiently small. Though EC7 allows the limit states to be verified by one or a combination of methods, use of calculations is by far the most used, and it is often confused with the EC7 itself. It involves using characteristic values of actions, ground properties and geometrical data, as well as obtaining their design values by the partial factor method.Characteristic value of a given material property is defined in Eurocode (EN 1990) as: “value of a material or product property having a prescribed probability of not being attained in a hypothetical unlimited test series. This value generally corresponds to a specified fractile of the assumed statistical distribution of the particular property of the material or product”. As regards the design value of a material or product property, according to the Eurocode it is a “value obtained by dividing the characteristic value by a partial factor”."

Jan 1, 2015