Search Documents

By R. J. Enright

Eight mines in canada and three in Australia were visited between September 1987 and Februacy 1988. All mines had encountered problems with sulphide dust explosions and had introduced defence mechanisms to prevent or limit the extent of these explosions. Techniques included dispersion of limestone by various methods, use of water foggers, placing of water and inert stenuning in blast holes, and removal of settled dust to prevent secondary explosions. The techniques were evaluated and it was concluded that certain practices should be modified or discontinued as they were of little value in preventing dust explosions.

May 11, 1988

By Turgut Yalcin

"In this study, potential benefits of focculant usage were explored in the processing of mill tailings by hydrocyclones. Tests conducted on copper-nickel mill tailings have demonstrated that, under suitable conditions, flocculation could significantly enhance solid-liquid separation in hydrocyclones. For example, at a feed pulp density of approximately 9%, focculant-assisted hydrocyclone produced an underflow with over 98% solids recovery, compared to a recovery of less than 53% with conventional hydrocyclone. However, feed pulp density was found to be a critical factor, and tailings with pulp densities of greater than about 15%required a two-stage hydrocyclone operation where the focculant-assisted hydrocyclone was employed at the second stage to process the overfow of a conventional hydrocyclone.The underflow and overflow products obtained from the focculant-assisted hydrocy-clone may be discharged into tailings dams in the same manner as those produced by gravity thickeners. The focculant-assisted hydrocy-clone would, however, provide a higher throughput."

Jan 1, 1996

By V. K. Karra

A mathematical model for the performance of a vibrating screen is developed in terms of an oversize partition curve. This is a normalized curve for any assemblage of particles presented for screening when their size is normalized with respect to the 50 per cent passing size (d50 ) under the prevailing screening conditions. Based on the throughfall aperture (hT) of the wire mesh on the deck, the effects of oversize (% >hT), half-size under (% <0.5 hT), deck location and feed rate were evaluated using the existing screen sizing information. All these variables and also the near-mesh (1.25 hTx 0.75 hT) content (%) of the feed affect the d50. Performance data from different decks of a double-deck screen with various feed rates, size distributions and screen apertures were used to evaluate the near-mesh factor. Effects of wet screening and material bulk density are also incorporated in the model. This generalized model is useful for the simulation of a multiple-deck screen. It furnishes the sieve analysis information of all the deck output streams and therefore has a potential use in the over-all circuit evaluation when used in conjunction with relevant crushing and grinding performance models. An example illustrating the prediction capabilities of the model is given.

Jan 1, 1979

By T. Mulpeter, G. Deschênes

Sadiola Gold Mine is an open pit operation located in Mali and owned by Anglogold Ashanti Ltd, Iamgold Corporation and the State of Mali. A conventional cyanidation process (cyanidation/CIP) treats 15,000 tpd (of a mixture of oxide and sulphide ores) at an average grade of 3 g/t Au. In 2002, the increasing tonnage of sulphides caused an increase in production costs and a decrease in gold extraction (from 95% to 70-76%). Because of the short retention time of the leach circuit (18 hours) and the refractory nature of the sulphides, gold leaching kinetics are critical. A laboratory investigation was initiated to evaluate actual plant practice and identify a means of improving the gold leaching rate. The study was conducted on a "soft" sulphide gold sample containing 4.96 g/t Au, 0.4 g/t Ag, 2.5% pyrite, 1.2% arsenopyrite, and 0.2% pyrrhotite with a P80 of 74microns. Pre-leaching significantly influenced the gold leaching rate. A short pre-leach (2 hours) performed at pH 8, a DO of 8 ppm, and with 300 g/t lead nitrate added at the start or the end, produced the preferred conditions. Pre-leaching for more than 2 hours was detrimental to gold extraction. The cyanide concentration had to be maintained at 450 ppm NaCN to reach a maximum gold extraction within the retention time of the circuit. A maximum extraction of 81.3% Au was obtained in 20 hours (leach residue at 0.97 g/t Au). A high level of dissolved oxygen in the pre-leach was not of any benefit. Extension of gold leaching beyond 20 hours indicated that all leachable gold had been extracted by that time. Plant modifications were made to allow leaching of oxides and sulphides in separate circuits. Treatment of oxide ores is now performed at a higher rate. Sulphides are processed at a lower throughput, with 300 g/t lead nitrate, to allow a retention time of 22 hours. Combined throughput remains the same, and total gold recovery has increased from 76% to 80% for an additional gold production of 16,000 ounces per year.

Jan 1, 2005

By Gordon A. Gross

During the last half century major steel industries of the world have become dependent on iron and manganese resources derived from siliceous ironformation sediments. More than two billion years ago vast amounts of iron and manganese were deposited in ironformation sediments on all continents and until recent years their genesis was considered to be a uniquely Precambrian phenomenon. Research work has demonstrated that the origin of the banded ironformations was related to major tectonic features and associated volcanogenic processes that were active throughout geological history. Similar sedimentary-tectonic environments are being explored on the seafloor where metalliferous sediments are forming today. Ironformations are now considered to be a major part of the stratafer group of stratiform metalliferous deposits. They developed in sedimentary basins in areas where deep tectonic fracturing intersected high thermal gradients in the earth?s crust and gave rise to profuse volcanism and the hydrothermal effusive discharge of metals in the vicinity of the volcanic centres. Concepts for the genesis and metamorphism of stratafer deposits as revised in the last half century have had a profound impact in the development of iron ore resources and have had a dramatic impact in the use of metallogenetic concepts for guiding exploration for other mineral resources. They are based on the tectonic history and stratigraphy in the sedimentary basins, the role of hydrothermal volcanogenic processes , as well as environmental and sedimentation factors which influence the deposition of silica, iron , and other metals that were emphasized in the past. Topics of special interest in the genesis of ironformation and stratafer deposits and for guiding mineral exploration are: biomediation in their sedimentation and genesis, the significance of metamorphism in the processing and beneficiation of iron ore and in the genesis of iron ore by natural enrichment processes, syngenetic concentrations of Mn, Ti, Cu. Zn, Pb, Ni, Co, REE, F, Ba, B, As, Hg, W and Au in ironformations and stratafer lithofacies, and the mobilization of gold and other elements by alkaline solutions during diagenesis of ironformation and other stratafer metalliferous sediments.

May 1, 2003

By J. I. Carroll, J. A. Walker

"Abstract - Camelback is a small (=200 000 tonnes), moderate grade (5%-7% Zn+Pb), volcanogenic massive sulfide deposit, which occurs within the Nepisiguit Falls Formation of the Ordovician Tetagouche Group. The host rocks are tuffaceous sedimentary rocks (Little Falls member) that overlie quartz-feldspar porphyritic tufflavas (Grand Falls member). The hanging-wall sequence comprises rhyolite of the Flat Landing Brook Formation, overlain by the Forty Mile Brook tholeiitic basalt. A dike of unaltered andesite was intersected beneath the massive sulfides, but was not found in the hanging-wall sequence in the vicinity of the deposit. The stratiform part of the deposit is made up of two, steeply south dipping, subparallel massive lenses that average approximately 4 m in thickness. Each lens is zoned, with an upper part consisting mainly of a pyrite and a basal part containing pyrite, sphalerite, and galena, with Ag values. The Au content in the massive sulfides is low (average = 52 ppb for 271 samples), but tends to be enriched in the massive pyrite near the top of each lens. Oxide facies iron formation is spatially associated with the massive sulfides, and has been traced up to 1800 m along strike. Footwall hydrothermal alteration is typical of VMS systems, and is characterized by depletion in K2O and Na2O, and enrichment in MgO and Fe2O3T with proximity to massive sulfides. The massive lenses are underlain by intensely chloritic, fine-grained, tuffaceous sedimentary rocks containing locally significant sulfide (chalcopyrite > pyrite > pyrrhotite) veins, which are interpreted to represent feeder zone mineralization. Unlike many VMS deposits, there is no evidence of silicification beneath the massive sulfides at the top of the feeder zone. The oxygen isotopic compositions (d18O = -1.5‰ to -0.3‰) of hydrothermal chlorite coupled with sulfur isotopic compositions (d34S ˜ 12‰) of the massive sulfides suggest that seawater was the dominant fluid in the hydrothermal system. Normalized rare earth element diagrams show flat Ce profiles and positive Eu anomalies, indicating that modified seawater was involved in ore formation; i.e., high-temperature (=350ºC), acidic, and reduced prior to entrainment into the hydrothermal cell. Although, seawater was the dominant fluid in the sulfide-forming system, d34S values of stringer zone sulfides (8.5‰) coupled with elevated Sn (400 ppm) in one massive sulfide sample indicate that there was at least some magmatic component in the hydrothermal cell."

Jan 1, 2006

By I. P. Swainson, A. Ilbagi, H. Henein

Powders of Al-50wt%Ni, Al-40wt%Ni and Al-36wt%Ni were produced using the Impulse Atomization technique, a rapid solidification technique. The molten droplets were cooled in-flight by the stagnant helium or nitrogen in the atomizing chamber. The resulting powders were sieved into different size ranges. X-Ray diffraction and neutron diffraction were used in order to quantify the phase fractions in the samples. The computer software GSAS was used to calculate the weight fraction of the existing phases, namely Al3Ni2, Al3Ni and Al, by profile refinement method. The effect of processing parameters, alloy composition and particle size will be discussed in this paper. In brief, no AlNi was found in any of the samples analyzed. Higher cooling rates resulted in the reduction of the ratio of Al3Ni/Al3Ni2. Also, at high cooling rates, Scheil closely predicted the ratio of Al3Ni/Al3Ni2. Some metastable phases were found in Al- 36wt%Ni.

Jan 1, 2010

By George F. Crocker

Introduction The Helen mine and the Victoria mine of Algoma Ore Properties, Limited, in the Michipicoten district, Ontario, are 120 miles north of Sault Ste. Marie, on the north shore of lake Superior. They are on the Algoma Central railway between Hawk Junction and Michipicoten Harbour. Between them, these mines have produced 10,757,113 tons of iron ore. From 1900 to 1918, 2,823,369 gross tons of brown ore was shipped, and from 1939 to the end of 1949, 7,933,744 tons of siderite was produced from the open-pit operations and underground development. The finished product, known as &apos;Algoma sinter&apos;, is shipped to blast furnaces both in Canada and the United States. The iron-ore bodies are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 feet and has maximum width of 1,000 feet. The two siderite orebodies, known as the Helen and Victoria, are separated by two diabase dykes. The Helen orebody is 1,600 feet long with a maximum width of 250 feet and the Victoria is 1,200 feet long with a width comparable to the Helen. These orebodies are considered to be a replacement of the original rock by iron carbonate. The introduction of the iron-1bearing material probably occurred after the development of the major folded structures. The open-pit mining of siderite started in the Helen ore body in 1939 and continued until 1945. During this period, 3,853,395 tons of ore was mined. Open-pit mining started in the Victoria body in 1946 and is still being carried on. Underground development commenced in September, 1947. Diamond drilling and surface sampling had shown the Helen deposit to average 35.61 per cent Fe and 7.28 per cent SiO2, and the Vi.otoria deposit 33.73 per cent Fe and 10347 per cent SiO2?

Jan 1, 1950

By Dave M. Jakelski, Gerhard W. Heinrich, Peter F. Wells, Daniel F. Suarez, Jamie B. Beauchamp

"A need for increased copper concentrate production and for less nickel contamination in that concentrate at Falconbridge's Strathcona Concentrator during 1993 required the installation of a third flotation column and improvements in the operation of the existing circuit. Innovations in wash water distributor and launder design were fundamental in achieving objectives on a new 3 meter diameter column. Minnovex plug-type spargers were tested on a 2.1 meter diameter column in order to reduce maintenance requirements. The paper details the measures taken to enhance column flotation circuit performance and the results obtained.IntroductionFalconbridge's Strathcona Mill receives 10% of the ore feed from a rich copper zone in the Strathcona mine. This ore typically grades 7% copper and 1 % nickel and, because of its high copper content, it is processed in a separate circuit ('C' circuit) which consists of conventional grinding, rougher flotation with the concentrate being treated with lime to pH 12.3 and cyanide followed by column flotation. The columns are operated with mechanical flotation scavengers and the scavenger concentrate is returned to the column feed. Testwork conducted in 1991 showed that the original flotation column (Column 2) could only produce 5.5 mtph of concentrate with less than 0.5% nickel (Figure 1).Between 1991 and spring of 1993, production was increased at times by open circuiting the scavengers. Metallurgical improvements were obtained by improving the wash water distributor of Column 2 and by wash water sprays in conventional cells (1 ). However, the scavenger concentrate assayed 0. 7 -0.8% nickel and was not acceptable for long term operation. When Copper ore production targets were significantly increased for 1993, it became clear that an additional flotation column was required. The new flowsheet employs mechanical scavenger cells on the column tails as in Column 2 circuit (Figure 2). A -parallel configuration was chosen as pulp solids fraction has been shown to be a critical variable and the second column in series would receive a lower density feed."

Jan 1, 1994

By Andreea Catalina Gluhoi

Oxidation and reduction reactions of N-containing molecules have been studied over different types of gold-based catalysts, Au/MOx/Al2O3 and Au/MIOx/MIIOx/Al2O3 (M, MI, MII=Li, Rb, Mg, Ce, Zr, Mn, Cu) prepared by deposition precipitation with urea. In general, all the catalysts were already active at low temperatures. NH3 oxidation was effectively catalyzed by Au/CuO/Al2O3, a catalyst which also gives the highest yield in N2. NO reduction by H2 performed over gold-based catalysts produced N2O, N2 and NH3 and N2O reduction resulted in the formation of dinitrogen. For all the reactions, large synergistic effects have been obtained by addition of different kind of additives.

Oct 1, 2003

By E. O. Magnusson

THE orebodies of the Preston East Dome mine show a considerable variation in size,? shape, dip, and ground condition. They vary from small and large irregular masses being mined by shrinkage, cut-and-fill, and square set-and-fill mining methods to narrow veins being mined by open stoping. Standardization of mining operations has necessarily been difficult. This considerable variation in mining condition prompted the development of a bonus system which would give more equitable bonus payments through-out the mine than those obtained by the usually accepted methods of calculating mine bonus. PRINCIPLES ON WHICH THE SYSTEM IS BASED Under an incentive bonus system, performance (efficiency) and a price per unit of work done are inter-related. It is in the application of this? principle to working conditions .in the Preston East Dome mine that the system to be described differs from the standard methods of calculating mine bonus. It was found that the method of paying a fixed price per unit of work done, under the &apos;contract&apos; system, gave satisfactory results in development, less satisfactory results in timbering, and results which were not satisfactory in stoping. Under the fixed price system, bonus payments, in timbering and stoping particularly, were very erratic and did not necessarily represent fair payment for the work done. A fixed price in development is satisfactory because the work done, and the conditions under which the work is done, are uniform. The drilling and blasting cycle is completed in one shift, the size of heading is con-trolled, and a minimum number of holes are required in order to obtain a satisfactory break. The performance possible under these conditions has been found to be confined to a fairly narrow range. By performance in development is meant the efficiency of the working crew as expressed in terms of the two variables of feet of advance per round and pounds of ex-plosives consumed per foot of advance. A change in rock formation, how-ever, may alter to a marked degree the performance possible, quite independent of the skill and energy of the working crew. The changes in working conditions that affect development performance from the standpoint of bonus calculation are usually easily apparent and are satisfactorily met by establishing several fixed prices.

Jan 1, 1944

By M. M. Helm

Samples sourced from the Goldstrike property in Nevada USA, have been evaluated in terms of their preg-robbing capacity and the physical structure of the graphitic carbon component in the carbonaceous gold ore. The study highlights a wide range in preg-robbing capacity between samples collected from the Betze-Post open pit and Rodeo underground mine. The physical structure of the graphitic carbon was assessed using Raman spectroscopy, and is found to play an important role in influencing preg-robbing behaviour. Differences observed in the physical structure of graphitic carbon are thought to be the result of hydrothermal events that occurred at Goldstrike.

Jan 1, 2011

By F. Y. Hsiao, H. C. Kao

Underground excavation in hard rock is normally stable at shallow depth except for wedge failure. However, the excavation depth is rapidly increasing recently. In high overburden stress condition, the integrity of rock would be destroyed with degrading rock strength. Therefore, understanding both the peak and the post-peak strengths of hard rock are necessary to assess the tunnel stability at depths. The characteristic of the post-peak strength is seldom studied in Taiwan in the past. Various estimation methods for the post-peak strength degradation were briefly reviewed in the paper. Based on the Geological Strength Index (GSI) system is widely used in the determination of the rock mass strength, the quantitative residual GSI system was adopted to estimate the possible strength degradation for a hydraulic tunnel in Taiwan. The Mohr-Coulomb model (no strength degradation) and the post-peak strength degradation model (strain softening model) were used to simulate the excavation of the case tunnel at different depths. The analyses demonstrate that the tunnel is in stable condition at 600m of depth. And the effect of the postpeak strength degradation on tunnel deformation is progressively significant with increasing tunnel depth. Approximate 3-5 times of increase in crown settlement and horizontal convergence would occur when post-peak strength degradation are considered at 2400m of depth. Severe tunnel deformation may endanger the tunnel stability. Modeling results reveal that the post-peak strength degradation has a great effect on tunnel stability under high overburden stress condition, which should not neglect in deep tunnel design.

Jan 1, 2015

By Robert A. Creaser, David R. Lentz

Abstract - The Moss molybdenite deposit, which was mined during both world wars, is hosted in late Grenvillian granitic pegmatite dikes. These dikes are locally aplitic, and intrude the late tectonic Onslow syenite (probably correlative with the ~1090-1070 Ma Kensington suite), which is in turn intrusive into the 1170-1155 Ma Chevreuil intrusive suite of southwestern Quebec. A Re-Os model age of 1053 ± 4 Ma (8.3 ppm Re) was obtained for molybdenite from a pegmatitic veinlet within an aplitic phase of the dike. A much younger Re-Os date of 860.9 ± 9.2 Ma (6.9 ppm Re) obtained previously from a pyrrhotiteand pyrite-rich metasomatic vein might reflect Os diffusion during slow cooling of the Grenville province, because this age is consistent with K-Ar dates reported from the region. Alternatively, the similarity between these younger dates may be fortuitous, and may instead relate to sampling issues for molybdenite. The Mo-rich granitic dikes at the Moss deposit are similar to other Mo-rich A-type pegmatite-aplite granitic dike systems that formed immediately after the peak of the Ottawan orogeny (1070-1090 Ma), and possibly are more closely related to the Kensington suite than previously thought.

Jan 1, 2005

By J. Kempken, R. Hagmann, C. -P. Reip, W. Hennig

The CSP technology symbolizes a highly productive process for the cost-effective production of steel grades with a range of sophisticated properties comprising both the inner quality of hot strip, its surface formation as well as the relating technological characteristics. Thanks to extensive development work undertaken during the last 15 years, the range of steel grades that can be produced was continuously expanded and the process technology optimized. The present paper describes the ongoing development work concerning the production of higher-strength, microalloyed pipe steels. The resulting hot strip, due to the associated thickness and the potential pipe diameters, is particularly suited for being processed to HFI-welded pipes. Based both on ferrite-pearlite as well as very fine-grained, ferrite-bainite hot-strip microstructures, strength levels of up to grade API X80 can be realized. It can be demonstrated that hot strip produced in a CSP plant has very good toughness values at temperatures down to -60°C and can even make application with required sour-gas resistance possible.

Jan 1, 2005

By Y. M. Shneerson, V. M/ Shpaer, E. E. Zhmarin, A. Y. Lapin, E. M. Vigdorchik

This paper describes studies of zinc concentrate oxidizing pressure leaching using the method of mathematical modeling. The concept of a kinetic function was taken as a basis for mathematical modeling of the leaching process. The kinetic function describes dependence of the unreacted component share OJ on the relative time x (the relative time is the ratio of the test duration and the time of complete dissolution). This kinetic function is determined in accordance with the results of batch laboratory tests. The laboratory tests have been carried out on zinc concentrate produced from Kazakhstan zinc-copper ores. Zinc concentrate consisted mainly of three types of minerals: sphalerite (70%), pyrite (13%) and chalcopyrite (10%). Oxidation reactions of sphalerite, pyrite and chalcopyrite have been considered as principal ones. The kinetic characteristics of the process (kinetic function, reaction order, activation energy, duration of complete dissolution of the concentrate components) have been calculated in the course of laboratory tests. The mathematical model was used for estimation of the main technological leaching process parameters (such as process rate, degree of metals extraction, autoclave capacity, heat balance, etc.). Mathematical modeling based on the kinetic function concept allows safe designing of metallurgical equipment and scaling the technology to industrial capacity.

Jan 1, 2004

By L. J. Cabri

A gold sample assaying 11.4 g Ault was selected for this study. Approximately 99% of the gold in this sample occurs as discrete gold minerals; the balance occurring as invisible gold in pyrite (determined by SIMS analysis). The sample was coarsely ground and sieved, yielding -38, 17, 22 and 22 wt.% in the -400+160 um, -160+80 um, -80+40 µm and -40 µm size fractions. Assays of the size fractions gave a gold distribution of -32, 20, 21, and 27% respectively. Processing with the hydroseparator (model HS-02) gave two tailings products and one concentrate from each size fraction. Assays of the concentrate from each size fraction gave gold recoveries of -7, 7, 24, 19%, respectively. Polished sections were prepared from each hydroseparation product and studied by image analysis to automatically search for gold minerals. Calculations were done using the surface area of the grains of gold minerals found on the polished sections.

Jan 1, 2005

Stellite-6 coatings were formulated on two Ni-base superalloys, namely Superni 75 and Superni 600, by a shrouded plasma-spray process, and the oxidation behaviour of these coatings has been investigated in air and in an aggressive environment of Na2SO4- 60%V2O5. Accelerated oxidation tests were conducted in a silicon-carbide tube furnace under cyclic conditions at an elevated temperature of 900°C for 50 cycles. Each cycle consisted of 1 h heating and 20 min cooling in air. A thermogravimetric technique was used to approximate the oxidation kinetics. The corrosion scales were characterised by XRD, SEM/EDAX and EPMA analysis. It has been observed that the coatings nearly followed the parabolic rate law of oxidation. Overall weight gain conceived in air was just 51% of that in the aggressive environment in the case of coated Superni 75, whereas in case of coated Superni 600, the cumulative weight gain in air was found to be one-third of that in the Na2SO4-60% V2O5 atmosphere. Furthermore, the coating showed very good adherence to both of the substrates during the course of air oxidation, whereas some superficial cracks were observed near the edges of the specimens during the molten salt induced oxidation. XRD analysis revealed the presence of phase-like CoO, CoCr2O4 and Cr2O3 in the oxide scales, which are reported be protective against high-temperature oxidation. The XRD results were further supported by SEM/EDAX and EPMA.

Jan 1, 2005

By V. G. Papangelakis, S. Peters

Pressure oxidation of refractory gold ores can be conducted on ores with high carbonate content using just water or water with alkaline reagents to promote fast kinetics, and suppress the formation of elemental sulphur and CO2. In this work, a fundamental study was conducted to explore the silica-pyrite interaction in the presence of calcium and sodium carbonate. It was found that an alkaline environment increases the pyrite decomposition kinetics on one hand, but on the other dissolves silica, which encapsulates the dissolving pyrite thus hindering ultimately its complete decomposition.

Jan 1, 2011

By Y. S. Sun, Northeastern University, W. B. Li, P. Gao, Z. Y. Zhang, J. W. Yu

"The boron-bearing iron concentrate was extracted from ludwigite ore by the process of magnetic-gravity separation. In order to fully utilize the refractory ore and meet the boron consumption of China, a novel process for separation of boron from iron in boron-bearing iron concentrate was proposed in this paper. In particular, laboratory scale experiments of improving boron reactivity were performed. Fine boron-bearing iron concentrate briquettes were reduced by bituminous coal completely at 1125 °C for 150 min. The effect of sodium carbonate, which was used as an additive in the roasting process, was investigated. The addition of sodium carbonate decreased the boron reactivity and facilitated the volatilization of boron. The influence of diverse cooling methods of the reduced samples on the boron reactivity was studied. The results indicated that boron reactivity could reach up to 80.76% when the reduced samples were cooled by rapid water quenching. In addition, the magnetic material containing 92.71 % Fe with a recovery of 95.11 % and boron-rich non-magnetic material containing 14.51% B2O3 with a recovery 88.85% could be obtained by low-intensity magnetic separation. The magnetic material and boron-rich non-magnetic material were good raw materials for steel-making and borax production, respectively.INTRODUCTION Ludwigite ore is abundant in Liaoning province of China, with 28.43 Mt B2O3 accounting for 57% of the boron resources of the country (Liu et al., 2006). However, it has not yet been utilized on an industrial scale due to its complex mineralogy and fine mineral dissemination (Wang, Wang, Ding, Ma & Xue, 2012). At present, boron-bearing iron concentrate and boron concentrate can be obtained from ludwigite ore using magnetic-gravity separation. The boron concentrate contains B2O3 12%~16%, which can be used as a high-quality raw material for the boron chemical industry after activated roasting, but the B2O3 content in the iron concentrate reaches up to 4%~6%. In order to further separate boron and iron from boron-bearing iron concentrate, a blast furnace and a solid pre-reduction followed by electric arc furnace melting have been proposed (Liu, Cui & Zhang, 1998; Wang et al., 2012). However, both of these two current routes face the same crucial problem that molten boron-rich slag has to be cooled slowly to obtain the alkali-dissolution activity of boron, which affects the yield of boron resource."

Jan 1, 2016