Search Documents

By Sarah R. Hindle

Carbon capture and storage has jumped to the forefront of climate change mitigation efforts for its capacity to sequester large amounts of carbon. Mineral carbonation is one prominent option, mimicking and accelerating the natural weathering process of certain silicate minerals. This has the ability to produce stable carbonate minerals that can store carbon on geologic time scales with little to no risk of leakage. Commercialization of this process is ideally suited for integration into the proposed mining operations at the Turnagain Nickel site in Northern BC. This is due to the abundant supply of suitable ultramafic feedstock material, as well as the economic benefit of sharing costs while reducing net emissions and bringing value to otherwise valueless and costly waste rock. While studies have shown this process to be technologically viable on a laboratory scale, assessing the economic and financial viability of such a process on an industrial scale is necessary. An evaluation of the financial feasibility of integrating mineral carbonation into the mining cycle at Turnagain under a proposed cap-and-trade system is presented.

May 1, 2010

By L Munholand, G. Soucy, P. Quintal

This work presents early results from the first study to optimize the hydrodynamics of a Plasma Lift Reactor (PLR). The PLR is designed to break down organic contaminants in aqueous solutions. New experimental results are presented for air/water tests and for plasma degradation of organic contaminants in Bayer liquor. In addition, a multiphase Computational Fluid Dynamics (CFD) model has been developed which predicts the hydrodynamic behavior in the PLR. These results of this work suggest the PLR is effective at reducing contaminants in the Bayer liquor and that the CFD model adequately describes the hydrodynamic flow.

Jan 1, 2005

By T. G. Joseph

ABSTRACT: The Canadian oil sands provide some of the harshest mining conditions in the world. Asoperations demand ever bigger tools, the toll on large mobile mining equipment is high, with structurallife often half of that expected. Soft ground conditions predominantly lead to fatigue failure scenarios, poor stability, and inconsistent payload evaluations. These challenges are not solely a concern for Canadian oil sands mines; there are far-reaching implications for surface mining equipment in any poor ground-operating environment. This paper focuses on the basics of payload evaluation, motion response and a simple estimate of structural life for haulers.

Jan 1, 2011

By B. Karnath, K. Guha, S. Tandon

At Jhagadia Copper Ltd (India), Copper is produced through secondary route using Top Blown Rotary Converter (Kaldo Furnace). The basic raw material being treated includes Matte-slag Reverts, Copper Cakes, dross & Cement, Oxide Ore, Low S bearing Concentrates & various metallics along with high grade copper scraps. The plant has capability to refine & produce Blister grade copper from Kaldo furnace as well as PS Converter . Blister is fire refined in Anode furnace & electro refined in Refinery to produce cathode copper. Our product , Copper Cathode , has already been established in the market as its quality is better than 'LME Gr'. The paper deals with the experiences encountered during commissioning & stabilization of the plant.

Jan 1, 2007

By F. Parada Luna, F. Parada Torres, J. Salvo, A. Reghezza

In the pyrometallurgical processes of copper concentrates, arsenic is preferentially concentrated in the dusts carried by the gases as a result of their volatility and subsequent condensation in the gas cleaning train. In this work results obtained by alkaline leaching of the dusts from Ministro Hales roasting plant, belonging to Codelco, are presented. For the Ministro Hales plant the alkaline leaching would be an alternative to the recirculation of dusts to the roasting furnace. The experimental study considered NaOH and NaOH plus NaHS leaching of two samples of dusts, with 4.24 and 2.55% arsenic respectively. The results show that it is feasible to extract 90% of the arsenic and 50% of the antimony at room temperature using only NaOH, and when the temperature increases to 95ºC, the extractions of As and Sb increase. Copper remains in the solid residue with less than 1% dissolution, and the NaOH net consumption was approximately 140 kg/t of dust. In leaching tests with NaOH + NaHS, two types of methods were tested, baking plus leaching with water and direct leaching with a NaOH+NaHS solution. With the second method arsenic extraction increased to 95% and copper dissolution was less than 0.01% at 85ºC, NaOH 100 g/L, NaHS 90 g/L, 1.5 h and L/S ratio of 5/1 (L/kg). The bismuth remains stable in the solid in all cases. INTRODUCTION The presence of arsenic in copper concentrates has increased with time and the environmental regulations are becoming increasingly more stringent. In concentrate treatment pyrometallurgical plants, most of the arsenic is volatilized condensing in the gas train and is collected along with the entrained solids to form the flue dusts. Under these conditions, in smelters of copper concentrates with high arsenic content, the dusts are being treated in hydrometallurgical plants to extract and stabilize the arsenic, which also means that most of the copper contained in the dust is co-extracted with the arsenic. This affects the recovery of copper in the smelter and an alternative such as the selective alkaline leaching of arsenic, would allow the copper from flue dust to be recovered.

Jan 1, 2019

By J. Robison, H. Pieterse, C. C. Smith, M. Luque, S. Chipman

Phase change during pressure let down releases significant amounts of energy that must be controlled to avoid undo wear and tear on equipment. Hydrometallurgical slurries require flow control equipment (valves and tanks) made of expensive materials to withstand the abrasive, and often corrosive nature of the slurry. Presented is a model of the nozzle of a let-down choke which is designed to control the flow pattern that exits the choke (valve) as it enters the receiving tank. This model can be used to design chokes which allow for the dissipation of the energy released during pressure let down by spreading the stream over a significant portion of the slurry pool in the receiving tank to minimize wear on equipment near the nozzle exit and the bottom of the slurry tank. An example uses the model to choose the nozzle expansion (area) ratio to select the outlet slurry velocity and slurry expansion angle.

Jan 1, 2004

By J. A. Rogers

"The Arthur W. White Mine (formerly Dickenson Mine) is a structurally controlled, hydrothermal gold deposit. A gold producer since 1948, it has, to December 31, 1990, processed 6.9 million (m) tons (T) of ore grading 0.45 ounces per ton gold (oz/T Au). As of December 31, 1991, Proven and Probable Ore Reserves were 3.2 m. T. at 0.32 oz/T Au. The mine is located just east ofPlacer Dome Inc. 's Campbell Mine, within the Cochenour-Gull.rock Lake deformation zone. It is situated on the hanging-wall side of a southeast-plunging anticline in a sequence of metamorphosed Archean volcanic, sedimentary and plutonic rocks of the Red Lake greenstone belt. Ore-bearing structures, found mainly within basaltic rocks, are brittle within greenschist-facies rocks to the northwest, but become more ductile toward the southeast, in amphibolite-facies rocks. Within and proximal to these structures, carbonate and arsenopyrite alteration decreases, whereas biotite, actinolite, pyrite and pyrrh otite all increase to the southeast.Ore and shear structures occur symmetrically about the northwest-trending, steeply southwest-dipping, flattening foliation . The three most common ore trends are on average: (A) northwest trending with a 55 degree to 85 degree dip to the southwest; (B) north-trending with a 40 degree to 50 degree dip to the west; and (C) due east-west-trending with a vertical dip. In general, the dominant direction of economic gold concentrations are explained and thus predicted by considering deformation style (brittle or ductile), rock anisotropies such as bedding and lithological contacts, and direction/magnitude of relative block movement. Direction ""A"" can be found adjacent to both right- and left-handed faults. Direction ""B "" occurs with dominantly right-handed systems and direction ""C"" is found with predominantly left-handed movement. Major faults active prior to, during, and after ore formation can have offsets in the order of 2500 feet. Movements along these faults were transpressive while their conjugate breaks were dilatant, thus creating zones for alteration and ore solution emplacement. A series of faults , each with offsets up to 30 feet were established under lower temperature brittle conditions during late- to post-ore formation. In more complex zones, formed during more ductile deformation, these faults controlled the localized geometry and, thereby, the depletion and enrichment of ore shoots, causing a high nugget effect.Although an important aspect of production planning and monitoring, grade control is also very important within a complex ore zone so that the nuggets are not missed. Detailed observation of structure at the hand-sample scale and detailed mapping at the stope scale give valuable clues to interpreting the structures on a mine-wide scale. Determining the relative movement along fault structures is very important so that using an action-reaction- type logic, potential dilatant areas can be predicted and targeted for development and diamond drilling."

Jan 1, 1992

By E. De Souza

Energy associated with ventilating an underground operation comprises a significant portion of a mine operation's base energy demand and is consequently responsible for a large percentage of the total operating costs. Ventilation systems may account from 25?40% of the total energy costs and 40?50% of the energy consumption of a mine operation. Fans are the most important mechanical devices used to ventilate underground mines and the total fan power installed in a single mine operation can easily exceed 10,000 kW. Investigations of a number of mine main fan installations have determined their assemblage to be, in general, very energy inefficient. The author has found that 40?80% of the energy consumed by a main fan is used to overcome the resistance of fan assemblage components. This paper presents how engineering design principles can be applied to improve the performance and efficiency of fan installations, resulting in substantial reductions in power consumption, operating cost and greenhouse gas emissions. A detailed case study is presented to demonstrate that, by designing fan assemblages using proper engineering concepts of fluid physics and industrial ventilation design, main fan systems will operate at efficiencies well above 80?90% (compared to common operating efficiencies of between 20 and 65%), resulting in a drastic reduction in a mine's overall costs and base electrical and energy loads.

Aug 1, 2013

By William C. Martin

"Consolidated Sudbury Basin Mines Limited owns two mines, 4 miles apart, near the southwest end of Sudbury Basin. The Errington mine lies close to the north boundary of Creighton Township and about 18 miles by car from Sudbury. The Vermilion Lake mine is in Fairbank Township, on the south side of Vermilion Lake.The first discovery of base-metal mineralization within Sudbury basin was made by James Stobie in 1897 at Stobie Falls on the Vermilion River, half a mile west of the Errington mine. A few years later Alphonse Oilier made a discovery of massive pyrite with base-metal sulphides near the west end of the present Errington workings.No work of consequence was done on these discoveries until 1924, when Joseph Errington acquired options on a large acreage of ground which was later taken over by the Treadwell Yukon Company Limited. After considerable diamond drilling this company sank No. 1 shaft in 1926. In the next three years, a large amount of underground development was done, a pilot mill was constructed and operated for two years. All operations ceased in 1931 with the fall in metal prices. While in operation the pilot mill treated 186,172 tons of ore the average grade of which was 1·07 per cent copper; 1 10 per cent lead; 4·60 per cent zinc; 0·03 ounces gold; and 1 70 ounces silver.Up to the time of closing in 193 l there had been completed at the mine 26, 790 feet of lateral work and 75,500 feet of surface and underground diamond drilling. The company records, however, showed no figures on ore reserves, except broken ore in stopes amounting to about 60,000 tons. A study of the plans, prior to reopening the mine in 1952, showed 1,450 lineal feet of ore (at 1952 prices) opened up by drifting on the 300-foot and 500- foot levels. It is clear that no comprehensive picture of the structure was had at this time. The orebodies were considered to be very irregular pods scattered through masses of quartzite-carbonate in a sheared zone about 800 feet wide. In some way the ore was believed to be related to the tuff-slate contact zone. With this picture it was impossible to make a reasonable ore estimate or even gauge the tonnage potentialities with any feeling of reliability."

Jan 1, 1949

By J. W. Merks

"Simulation is the process of designing a computerized model, of a system or procedure, for the purpose of understanding its behaviour and developing strategies to control its operation. Simulation models are rapidly becoming an effective tool for mineral processing plants. Powerful software and fast hardware are more readily available than a basic understanding of the theory of mathematical probability and applied statistics that process simulation models demand.Simple spreadsheet software can be used to develop simulation models that take into account any set of conditions at a mineral processing plant. In addition to an unbiased estimate for each variable in the set on which two-and three-product formulas are based, reliable variance estimates for all variables are required. How to estimate variances, effectively and at the lowest possible cost, and how to compute variances for simple functions such as the metal content of a quantity of ore or concentrate, or more complex functions such as the percentage recovery at a mineral processing plant, are the key to useful simulation models.IntroductionSimulation models for systems and procedures have become one of the most powerful and effective applications for computers( 2.6). Simulations are applied to a wide range of scientific and engineering disciplines. Generally, a model is designed to investigate the effects of changes in and interactions between a set of variables before a system is in operation or a procedure is implemented, by simulating weeks, months, and even years of operation, in a few minutes of computer time. Along with practical and useful applications always comeabuse and misuse. For a simulation process cannot be more reliable than the methodology that was applied to design the model, to estimate variables and variances, to check performance, and to verify validity. A mineral processing plant is a dynamic system that changes continuously as a function of time but within probabilistic constraints that can be estimated by applying statistical tools and techniques to the variables and variances that interact in the system.A model should be designed to simulate not only the set of variables but also the variance for each variable. Models in which constant variances are used to generate normally distributed random numbers, are less realistic than models in which the variances are simulated first, and then used to simulate the variables."

Jan 1, 1991

By G. E. Agar

"The distribution of gold in the grinding-classification circuit of an operating gold plant was determined by assaying the size fractions of samples from each of the streams. This analysis identified the streams with the maximum potential for gravity recovery of gold and revealed that there was up 110 seventy-five times as much gold in the primary cyclone underflow as in the concentrator feed.Laboratory jigging and tabling tests were done on samples from two of the streams to determine what the recovery might be with a gravity circuit and to show that a high grade concentrate could be produced. A numerical simulation procedure was used to calculate a material balance for a circuit that included gravity separation on the primary cyclone underflow. The numerical simulation optimistically indicated that as much as 84% of the gold might be recovered in a reasonable grade of concentrate even though the recovery in batch bench scale tests was only 14%.Incorporation of a gravity separation device would reduce the inventory of gold in the grinding-classification circuit.INTRODUCTIONMany gold concentrating plants include a gravity concentration operation while others do not and the reasons that some do and some do not is not clear. Some of the advantages and disadvantages of gravity circuits are discussed by Penman (Penman 1987) without clear cut resolution. Penman's comments elicited an interesting response from Lloyd (1989) who produced a simple way to determine if the addition of a gravity concentration circuit would enhance the recovery of gold. Lloyd's method does not consider the cost of running the circuit so it only partially answers the question. There are reports in the literature (Wells and Patel 1991, Matwijenko 1988) that as much as 60% of the entire production comes from a gravity circuit when it is used, and that the grade of the concentrate produced often exceeds 65% gold, an assay that far exceeds most Merrill-Crowe precipitates that are sent to refining. In at least one instance (Hood 1984) a range of recovery from 40-50% was indicated from laboratory test work and the plant subsequently realized recoveries in the range of 26-40%. Despite these favorable numbers other plants use gravity separation when as little as 20% of the gold is recovered in the gravity concentrate (Carter 1992)."

Jan 1, 1993

By Z. D. Hora

The major fluorite producer in British Columbia was the Rock Candy Mine, inactive since 1942. Other deposits of economic interest include the Rexspar deposit, in which fluorite is associated with uranium and rare earth mineralization, and the Eaglet and Liard River occurrences. THE former Rock Candy fluorite mine, located 26 km north of Grand Forks, is the only major past producer of fluorite in British Columbia. The deposit was in production from 1918 to 1929 and again in 1942; total output was about 36,000 tonnes with average grade between 22 and 32 per cent CaF2. The fluorite body occupies a steeply-dipping vein structure, approximately 175 m long and up to 12 m wide, in porphyritic syenite. The chief vein-filling minerals are quartz and fluorite with local small len ses of barite. Fluorite content decreases with depth and the deposit becomes silicified. The Rexspar (or Birch Island) fluorite deposit is located 130 km north of Kamloops. The deposit is complex with rare earth elements and high uranium values, but !1uorite mineralization forms an independent zone adjacent to the uranium orebodies. Fluorite is present as fine-grained impregnations and as breccia cement in strongly schistose or brecciated alkali feld spar porphyry. Reported reserves are 1,088,000 tonnes of 22 per cent CaF2 or 450,000 tonnes of 29 per cent CaF2. 268 Another potential deposit of fluorite is Eaglet, situated on the north side of Quesnel Lake. Fluorite occurs as a stock work with scattered veins and irregular lenses up to 20 centimetres wide and as impregnations in altered Proterozoic Kaza Group feld spathic gneiss over an area of 1,500 metres by 500 metres. To date (1983) approximately $2 million have been spent on the exploration of this property and reserves of 18.8 mimon tonnes grading 11.59 per cent CaF2 have been outlined . A group of significant occurrences is known from north of Liard River Hot Springs Park , where fluorite occurs in small zones up to 17 m thick along the interface between Middle Devonian Dunedin Formation limestone and Middle Devonian to Mississippian Besa River Formation argillite. Fluorite, associated with witherite, barytocalcite and barite, is present as replacement bodies, breccia fillings and minor veins.

Jan 1, 1984

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-Fe0x-Ca0 ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04. 0

Jan 1, 2007

By Jochen Petersen, Alison Lewis, Cledwyn Mangunda

Run-off and waste water streams high in dissolved metal content are generated in all mining operations. The metals pose a threat to life due to their persistent bio-accumulative toxic (PBT) characteristics. Hence, there is a need to treat mine waste water effectively. Lime precipitation is the technology of choice through which Fe, as the major metal species, is removed as Fe (III) oxyhydroxides with other metals co-precipitated and/or adsorbed. Sulphates are removed as gypsum or incorporated into the Fe phases. The resulting sludge has poor dewatering characteristics and is deposited in landfills, with an inherent risk of returning the Fe back into the water cycle through leaching. This study seeks to understand the mechanisms behind the formation of this sludge in terms of product quality. The relationship between process conditions and product characteristics has been investigated through exploring the effect of Fe (III) concentration on the precipitate product characteristics (particle size distribution (PSD), size, morphology and structure) and quality (in terms of filterability, settling ability, etc.) in a simplified system. Neutralisation of acidic synthetic aqueous Fe (III) sulphate streams containing 50, 400 and 800 mg/L Fe(III), respectively, was effected by mixing it in a continuous stirred tank reactor (CSTR) with dissolved calcium hydroxide for pH control at a residence time of 15 minutes. Precipitate samples analysed for morphology and PSD, using nanoSEM and Zetasizer respectively, showed a general decrease in PSD and zeta potential with increases in feed Fe (III) concentration. These results were used to infer the particle size enlargement mechanisms of Fe (III) oxyhydroxide precipitates under a given set of operating conditions. Preliminary product quality results indicate that a high concentration (800 mg/L) leads to the rapid formation of metastable precursors with poor product quality, whilst a low concentration (50 mg/L) leads to formation of thermodynamically more stable precipitates with good product quality. The approach demonstrates a potential route forward in terms of linking operating conditions to the attainment of desirable characteristics rather than specific precipitate phases which are difficult to identify.

Jan 1, 2016

By C. Barnett

"A description of the Geco orebody has been given by W .L. Brown and R.C.E. Bray (1). The mill flowsheet and equipment were described by M.J.S. Bennett, D. Wild and C. Lawton (2). Mill capacity is now 4, 150 tons per operating day of copper, silver, zinc and lead ore. A recent flowsheet has been published in the - Canadian Mining Manual (1966).Soon after the start of production in September 1957, it became apparent that large tonnages of sand would be required by the mine for backfill pruposes. Initial experimental work on the preparation of sand fill from the flotation tailings was begun in late 19 59. Cyclones of local manufacture, in a variety of sizes, were tested quite successfully. There were, however, several obvious advantages with some of the custom-built cyclones and a recommendation was obtained from the Techniquip Company. A single Krebs D-10-B cyclone was tested experimentally in 1960.INITIAL TESTWORKExperimental results showed that with our relatively coarse grind (in the order of 53 % minus 200 mesh) 75 - 80% of the flotation tailings could be recovered as backfill sand with one stage of treatment. Percolation rates of four inches per hour were obtained with cyclone inlet pressures in the range of 20 - 25 psi and feed densities of 20 - 23% solids."

Jan 1, 1968

By A. Pranowo, G. R. F. Alvear F., N. Aslin, M. S. Moats

"The toxicity of arsenic is well known and documented; however, the presence of arsenic in copper electrorefining anodes and electrolytes is critically necessary to produce high-quality cathode. Arsenic as well as antimony and bismuth concentrations vary relative to their concentration in the anode copper received from the smelter. The behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance are discussed. This will include the minimization and mitigation of problems associated with arsenic, antimony, and bismuth—including cathode contamination, floating slimes, scaling, and anode passivation.RÉSUMÉ La toxicité de l’arsenic est bien connue et documentée; toutefois, la présence d’arsenic dans les anodes de l’électroaffinage du cuivre et dans les électrolytes est d’une nécessité critique pour produire une cathode de grande qualité. Les concentrations en arsenic, ainsi qu’en antimoine et en bismuth varient selon leur concentration dans l’anode de cuivre reçue de la fonderie. Le comportement et les avantages de l’arsenic dans l’électroaffinage du cuivre et les effets indésirables de l’antimoine et du bismuth sur la qualité de la cathode et le rendement des cuves d’électrolyse sont discutés. On traite aussi de la minimisation et de l’atténuation des problèmes associés à l’arsenic, l’antimoine et le bismuth – incluant la contamination de la cathode, les schlamms flottants, l’entartage et la passivation de l’anode."

Jan 1, 2016

By Dale A. Walters

The thermal recovery of bitumen reservoirs by steam assisted gravity drainage (SAGD) is often designed to maximize the operating pressure. In general, the benefits of higher operating pressures are higher steam temperatures that maximize the reduction of oil viscosity, potential permeability enhancement associated with lower effective stress and shear dilation, and a larger pressure window to allow flexible control of the producer. This is especially important for shallow reservoirs where the pressure window for injection and production is smaller. Higher operating pressure can reduce thermal efficiency (due to heat losses), but the other benefits usually compensate. The limitation of the maximum operating pressure is then based on maintaining caprock integrity. Thus, shear and tensile failure mechanisms must be quantified and managed. This paper presents a geomechanical analysis of caprock integrity for SAGD operation. Both analytical and numerical approaches are used to investigate the modes of caprock failure. Main factors in the analysis are the knowledge of the initial stress state and proper representation of the complexity of the geomaterials. Typical initial stress states for northern Alberta are presented showing the potential for low initial minimum total stress and elevated initial shear stress levels. The stress-strain behavior for the sand and caprock materials is discussed focusing on the potential for shear dilation in the sand and shear strength behavior in the caprock. Elasto-plastic constitutive models used to represent the sand and caprock are presented and compared using numerical analysis. The increase in pressure and temperature alter the stress state and disturb the soil matrix. This disturbance results in shear dilation of the sand matrix creating regions of enhanced permeability and porosity. Also, the transfer of stress and strain to the caprock causes dynamic stress changes and, therefore, dynamic behavior of shear and tensile failure conditions. Calculations are presented showing the stress paths associated with SAGD operations, suggesting better design of lab testing programs and the implications for shear dilation in the sand and shear failure in the caprock.

Jun 1, 2012

?Bank Lending to the Mining Sector affected by 2 broad factors since Mid 2008: 1. Economic Downturn (?the Real Economy?) for mining companies directly reflected in lower metal prices (current and forecasted). In the case of gold companies, minimal effect. 2. Financial Crisis (?the Credit Crunch?) as it has affected the lending activities of those banks active in the mining sector.

May 1, 2009

By Jeffrey S. Loen

"Abstract - The size, morphology, surface texture, per cent mineral inclusions, and bulk chemistry (Ag and trace elements) of placer gold particles vary systematically according to transport distance from source rocks, as indicated by a case study from the Pioneer district in Montana, and data from the literature.Placer gold samples show a rapid decrease in mean and maximum particle length, and a gradual increase in flatness index (F.I. = length + breadth/2 X thickness) from about F.I. = 2 in bedrock deposits, to as much as F.I. = 45 over transport distances of several tens of kilometers. Primary mineral inclusions (mainly quartz, sulfide minerals, and iron oxides) are mostly lost within 10 km to 20 km of fluvial transport; this loss of quartz and trace metals causes a major change in bulk chemistry of placer gold samples. Following the loss of inclusions and the development of flakes, edges of flakes are folded and the mean number of folded edges in a sample increases with distance. When viewed under the electron microscope, surface textures of placer gold particles also become progressively more pitted with distance.Analysis of placer gold particles can be used to help evaluate placer source-area problems (placers with no known hard-rock gold deposits). For example, coarse placer gold containing abundant inclusions indicates a proximal source. On the other hand, an abundance of thin flakes is evidence of a long transport distance and possible reworking from older gravels. Placer gold characteristics can therefore provide information on distance to mineralized source rocks."

Jan 1, 1995