Search Documents

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The major importance of liners in grinding is their role in providing an appropriate trajectory for the charge. Since it is not possible to study the charge movement by direct observation in operating industrial mills, this task is accomplished by physical (laboratory), and/or, mathematical (software) methods. Because of the high cost and a longer time required for a physical analysis, mathematical simulations have become more common. Simulation of the effect of liner shape on the charge movement has provided a means to select a proper design based on the operational objectives and conditions. Furthermore, the liner shape changes due to wear and impact during operation, which will influence the charge trajectory. This adds more of an incentive to use simulation. These changes in liner could be predicted through liner profile measurements during operation and/or simulation. In this research, an inhouse developed DEM software called KMPCDEM © was used to simulate the charge movement in industrial plant SAG mills. A geometrical method of implementing the shell liners on SAG mills at the Sarcheshmeh (9.75×4.87 m) and the Gole-E-Ghohar (9×2.05 m) operations facilitated the software simulation. Point by point implementation of the measurements of liner profiles of these mills enabled the study to trend the change in the charge movement as the liners wear. Comparison of the simulation to a laboratory mill (1 m diameter) showed that the difference between the measured and predicted charge impact point, shoulder angle and toe angle were 6, 4 and 3°, respectively.INTRODUCTIONComminution is the most energy intensive operation constituting the major portion of operating and capital costs of a mineral processing plant. In the last decade, a vast number of research was aimed at studying various aspects of grinding with the aim of performance improvements (Davis, 1919; Mishra & Rajamani, 1990; kalala, Breetzke, & Moys, 2008). Mill liners transfer the input power to the charge and play a significant role in affecting the motion of the charge (Mclvor, 1983; Mishra & Rajamani, 1990; Radziszewski, 1997; Van Nierop, Glover, Hinde, & Moys, 2001; kalala et al., 2008). Lifters are usually used with mill liners to extend their life and to enhance the grinding and impact breakage efficiency. Mill lifters are used to raise the grinding media and ore to transfer the energy from the mill to the load (Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010)."

Jan 1, 2016

By A. A. Ruitenberg, L. R. Fyffe

"This paper compares several distinct types of mineral deposits associated with different families of granitoid rocks in the New Brunswick Appalachians. Porphyry copper deposit s are associated with late-stage differentiates of Lower to Middle Devonian I-type igneous complexes. Contact metasomatic deposits were formed where these plutons intrude carbonate rocks and they gave rise to vein deposits in fracture zones near wrench faults. The I-type granitoids were emplaced mainly in areas of thin continental crust and locally along prominent faults in areas of thick continental crust.In contrast, tin-tungsten-molybdenum-bearing greisen deposits and skarns, and antimony-bearing quartz veins are associated with predominantly S-stype granitoid complexes ranging in age from Middle Devonian to early Carboniferous. The mineral deposits occur within or along the contacts of very fractionated (specialized) late phases of these intrusive complexes, which are characterized by high K2O/Na2O, Rb/Sr and Rb/Ba, and low Fe, Mg, Zr and Ti contents. These specialized granitoids are in a large wrench fault zone that cuts across thick continental crust in southwestern and central New Brunswick.IntroductionA great variety of igneous intrusions and subvolcanic stocks were emplaced in the New Brunswick Appalachians during the latter stages of and immediately after the Acadian Orogeny (late Lower to Middle Devonian) and during the subsequent Hercynian Orogeny (Carboniferous). The presence or absence and characteristics of mineral deposits associated with these intrusions reflect the level of intrusion, the composition of the associated igneous rocks and the composition of the invaded sequences.Nickel-copper sulphide deposits occur in mafic intrusions in the St. Stephen area of the southwestern Magaguadavic - St. Croix Zone and in the Goodwin Lake area of the northeastern Mirarnichi Zone. Contact metasomatic and vein-type copper-rich base metal sulphide deposits and porphyry copper deposits with or without molybdenum are related mainly to high-level granitoid stocks of intermediate composition in the Matapedia-Tobique and northwest Miramichi zones. Tintungsten - molybdenum deposits with or without base metal sulphide minerals and antimony-uranium deposits are mainly associated with Upper Devonian and Lower Carboniferous biotite-muscovite granites and related 'subvolcanic intrusions that occur in an arc-shaped belt extending from the southwestern Magagaudavic - St. Croix Zone into the central Mirarnichi Zone."

Jan 1, 1982

By K. Halada

Current trend of the global flow of strategic metals are analyzed to discuss the strategy of the development of recycling technology and alternative technology. In many cases, each global flow of metal is changing from the trilateral structure of U.S., EU and Japan in the later 20th century into the convergence to China as the factory of the world. Scrap flows are also changing dynamically. A long term change of prices of metal has gotten changed since the entrance of this century. The estimation of metal consumption up to 2050, in which the author estimated that many kinds of metal will overshoot the reserve base line, is revised considering these change of current trends.

Jan 1, 2014

By Patrick S. Hudd

Traditionally in hard rock mining, large diameter raise boring was thought of as 3.04 metre or 3.66 metre diameter holes 300 metres deep. Mine and ventilation engineers were challenged to design systems either incorporating such holes, or slashing and modifying to suit. Now, 5.49 metre diameter holes up to 1,000 metres deep are being excavated. The ability to pilot and ream such holes not only creates new options for mine engineers in mine ventilation system design, but also creates new opportunities in mine access. By combining holes of this diameter with the ability to accurately drill long pilot holes within the diameter of the pilot hole through the entire length of the hole, borehole hoisting systems are now fully capable of being main production or service accesses for mines. This paper will review the present day capabilities of large diameter raise boring, potential applications for such excavations and some considerations for companies contemplating using large diameter raise boring in their operations

Oct 1, 2010

By Gary Pattrick

A new class of spongy Au catalysts is studied for the selective catalytic reduction of NOx by propene under leanburn conditions. The spongy catalyst is an unsupported powdered Au that consists of micrometer particles (~5 microns) that have nanometer scale (~10 nm) internal skeletal structures. The effects of alloying 1 ? 50 atom % platinum group metals (M= Pt, Pd, Rh) and 5 wt% first row transition metals (M = Ti, Mn, Fe, Co) were studied. Even low additions of PGMs (1 at.%) cause significant shifts to lower temperature regions of activity and the largest shift is obtained for Rh. For Rh this is interpreted as a strong synergistic interaction between Rh and Au. Possibly related to the Rh effect, Co is the only other metal studied that lowers the temperature of NOx reduction. The other first row transition metals inhibit the reduction reaction.

Oct 1, 2003

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe."

Jan 1, 2017

By Daniel J. Corkery

Mines in Canada and the United States are subject to regulations limiting ammonia, nitrate and nitrite levels in mine effluents released into the environment. The primary source of these nitrogen compounds is typically explosive used in blasting operations, as ammonium nitrate (AN) remains a significant component of most explosives used in the mining industry. The amount of AN entering a local water drainage system is related to site conditions, explosives used, explosive handling and blast efficiency. Mining operators acknowledge AN loss to mine water from blasting operations. However, the mechanisms by which ammonia, nitrite and nitrate are entering the water drainage system, or the relative contribution of specific mechanisms, may not necessarily be assessed or monitored adequately. Characterization of these mechanisms, through systematic investigations, allows a mining operation to focus its efforts on reducing AN loss. This paper outlines a strategy for investigating the mechanisms through which AN enters the mine water drainage system and methods to mitigate this loss. This strategy includes collection and analysis of data to identify and quantify the AN loss mechanisms, design and implementation of tests to mitigate this loss, and assessment of the results. Such investigations are not intended to be a separate one-time project, but part of a long-term process of continual feedback and optimization that is related to the collection and reporting of AN levels for regulatory purposes. The implementation of the strategy must be tailored to each mine?s requirements and existing conditions.

Oct 1, 2010

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By Gonzalo Bernstein, David G. Meadows, German Naranjo, Edgardo Tapia

"During the last decade Antofagasta Minerals’ Los Pelambres Mine has dramatically increased its ore throughput following the fast initial phase ramp up through a series of planned incremental expansions. The original 85,000 mtpd, two SAG line plant was commissioned in 1999 and rapidly exceeded nameplate tonnage in only a few months. Following this, the inclusion of a pebble crushing circuit resulted in throughputs in excess of 114,000 mtpd and a recent, final third line SAG and ball mill addition have taken the plant to over 175,000 mtpd even with increasing ore hardness and changing ore feed characteristics. The progressive changes are described in this paper together with how the technical challenges have been met.INTRODUCTIONMinera Los Pelambres is a world class copper-molybdenum operation located in the Salamanca area in Chile, in region four, approximately 500 km north east of Santiago, the capital of Chile. In the late 1990s Antofagasta Minerals developed the Minera Los Pelambres project in Chile at an investment cost of approximately $1.3 billion USDs. The project construction was successfully led and completed by Bechtel Corporation in 1999 and within a matter of months the plant was already exceeding the nameplate capacity of 85,000 mtpd. In 2001 a pebble crushing circuit was added to raise the capacity to 114,000 mtpd. In the early part of 2003-2004, it was recognized that the hardness profile was changing with depth and that in order to maintain the plant capacity additional power would be needed in the SAG mills together with upgrading of the primary crusher. In conjunction with these changes a fifth ball mill and a second primary crusher station would also need to be installed. A further detailed engineering study and evaluation was initiated by Minera Los Pelambres. This was lead by Bechtel Corporation with major design contributions from FLSmidth and Siemens in order to establish the re-powering requirements for the SAG mills. These re-powering changes together with the inclusion of a pebble crushing circuit took the plant to up to 125,000 mtpd even with harder more competent ores. Finally in the last two years an additional grinding line has been added to take the capacity to consistently over 175,000 mtpd. The third line was installed in a record time of 256 days. A schematic of the current comminution circuit, discussed in this paper, is shown in Figure 2."

Jan 1, 2012

By K. A. Hildebrant, J. R. Norgate

"Synthetic lubricants have for many years documented extended service life and provided superior performance in temperature extremes. Increasing interest in synthetics' ability to reduce energy costs has resulted in laboratory and industry application evaluations. These tests have documented savings in functions such as worm gear drives, spur gears and in compressors. Energy savings data are presented as well as payback calculations as low as thirty days.The National Research Council of Canada has estimated that the Canadian economy loses over five billion dollars per year in friction and wear. Figures quoted were for 1986 during which it was estimated that nine hundred and forty million dollars were lost in the mining industry alone"" It has been further estimated that about 115 million dollars can be immediately recovered through improved tribology practices (Table I).The purpose of this paper is to present results and savings opportunities through the use of synthetic lubricants in various but common applications. Many other areas exist with the opportunity for energy savings such as in the use of more efficient drive equipment, reduced contact seals, spray mist lubrication systems and reduced friction coatings on rotating equipment such as pump impellers"

Jan 1, 1994

By S. N. Dixon

"Maximizing the value of each tonne of processed ore is the goal for all operations. Cyanidation processing of gold-copper ores has been challenging since its first use in 1889. The current practice treats a bleed or the total flow of mill solution to recover copper as copper sulfide (by sulfidization, acidification, recycling, and thickening), or to recover the cyanide (by acidification-volatilizationneutralization). The process presented uses the adsorption of copper cyanide by carbon and the selective elution of copper from carbon to concentrate copper into a smaller stream. Copper contained in the smaller stream is precipitated as copper cyanide.RÉSUMÉ Toutes les exploitations ont pour objectif commun d’optimiser la valeur de chaque tonne de minerai traité. Depuis sa première utilisation en 1889, la méthode de traitement par cyanuration des minerais aurifère et cuprifère s’est révélée complexe. La pratique actuelle traite la saignée ou le débit total d’une solution de traitement du concentrateur pour récupérer le cuivre sous la forme de sulfure de cuivre (par sulfuration, acidification, recyclage et épaississement), ou pour récupérer le cyanure (par acidification, volatilisation et neutralisation). Le procédé présenté dans cet article utilise l’adsorption sur charbon actif de la solution de cyanure de cuivre et l’élution sélective du cuivre depuis le charbon pour concentrer le cuivre en un plus petit jet. Le cuivre contenu dans ce plus petit jet est précipité sous forme de cyanure de cuivre."

Jan 1, 2017

By J. S. Stewart

THIS paper was prompted by a persistent demand for what information we have that will throw light on the oil and gas possibilities of the Maritime Provinces. The problems involved were made familiar to the writer during three seasons of field work in New Brunswick and Nova Scotia. The reasons for renewed interest are: (1) In many parts of that region, the surface is underlain by a thick series of unaltered sedimentary rocks. (2) Oil seepages occur, and oil in commercial quantity has been exploited' near Moncton, New Brunswick, for many years. (3) In recent years, a new method of attack has been developed toward the finding of stratigraphic traps. This method is based on a detailed study of the geological history of the region, as revealed in surface outcrops and samples from deep wells. The well samples show the lateral variation of strata, far from any possible surface outcrop of the same beds. Sufficient work has now been done in the Maritime Provinces to reveal the broad features of the geological history and the character and distribution of the various rock formations. Comparatively little deep drilling has been done in this region, but the holes are widely scattered and the samples from them have added much to the information obtained from the numerous outcrops of bed-rock. The following discussion gives a summary of available information that has a bearing on the subject.

Jan 1, 1943

By P. M. Solozhenkin, O. I. Ibragimova, I. P. Solozhenkin

Molecular models of complexes of poorly studied bismuth, gold, and arsenic mineral clusters and reagents were created for use in collector activity forecasting using Chem Bio 3D and ChemOffice2005, with optimization by MM2. The density functional theory approach was used to determine HOMO, LUMO, SOMO, and total energies, atomic charges, and s, p, d- populations for various compounds. The structure-based virtual screening (SBVS) and docking technique was proposed to reduce the vast number of compounds to a more manageable number for selection of potential flotation candidates. The prognosis of collector activity evaluation (PCAE) strategy was proposed as a consistent approach to estimate the interaction between a collector and a mineral cluster as the difference between the total energy and sum of cluster energy and collector energy to search the analogue of butyl xanthate. The negative relationship between PCAE and flotability was shown. The combinations of dialkylamino sulfhydryl collectors can be considered as prospective reagents for gold-bearing sulfide ore flotation. These results were confirmed by experimental data in ore flotation. The increase in recovery of gold and bismuth with the aid of a combination of reagents has been established and additional cyanidation of tailings has been avoided.

Jan 1, 2016

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"Abstract-A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By D. B. Dreisinger, M. R. Tavakoli

Vanadium has been produced from a variety of sources. This metal is known to make aqueous solutions of complex speciation as a function of vanadium concentration and pH. Considering the method of leaching, the impurities in the PLS and the planned vanadium product, different extractants and flowsheets can be applied for solution purification. In this paper, purification of vanadium leaching solution using organophosphorus, solvating and amine extractants will be reviewed. This review will be focused on vanadium separation from iron, molybdenum and uranium which are often present in vanadium resources including primary ores, fly ashes and spent catalysts.

Jan 1, 2014

By K. A. Foxford, D. A. Polya, R. P. B. Hebblethwaite

"A variety of techniques for interpreting systems of mineralized echelon veins is discussed using examples from Panasqueira and SW England. As aids for exploration and mine planning, and as a tool for ore reserve evaluation, particular emphasis is placed upon establishing vein morphology in the third dimension, and upon understanding vein dilation and propagation histories. Special attention is also placed upon investigating vein thickness and spacing relationships, and upon understanding vein segmentation. The relevant data for these techniques are all readily obtainable from stope and core sources.The vein systems described were produced in host-rock sequences that underwent incremental dilation in response to fluid overpressures, and individual veins display evidence for mineral infilling synchronous with their propagation. Echelon vein geometries resemble those reported from igneous dikes and sills: vein walls are stepped and veins are divided into segments arranged in echelons. Changes in vein geometry, from arrays to composite structures, reflect both the evolution of the vein system with time, and the changes occurring between the margins (arrays) and core (composite structures) of the system. These characteristic morphologies can be used to infer vein propagation and fluid injection trends, proximity of neighboring veins, and the shape of the system as a whole. The techniques are applicable to systems of echelon veins produced under tensile conditions in rocks where faults were absent at the time of vein formation, and where subsequent deformation has been minimal. Further work is required to assess the application to echelon vein systems formed within more complex tectonic regimes."

Jan 1, 1995

By Robert B. Parsons

"Effective January 1, 1990, mines in British Columbia are subject to a new provincial mining tax statute, the Mineral Tax Act. Under this Act, mines are subject to a two-tier tax system, with a minimum tax payable on ""net current proceeds"" and a higher tax paid on net income. For many mines, the present value of tax paid under the new rules should be comparable to the amount paid under the old rules. Earlier cash payments could pose difficulties, particularly for smaller mines, but existing producing mines could benefit in the short-term.IntroductionEffective January 1, 1990, British Columbia has replaced the provincial mining tax regime under the Mineral Resources Tax Act with a new system under the Mineral Tax Act. The new rules borrow some ideas from other provinces (New Brunswick's two-tier concept, and Saskatchewan's indexed costs) with a view to levying a tax that is fairer to both the producer and the province."

Jan 1, 1990

By William D. Swank, Prabhat K. Tripathy, Tedd E. Lister, Eric S. Peterson, Delon C. Haggerd

More than half of the primary neodymium, produced directly from ores, is being used to manufacture neo magnets. Neodymium, being a critical element in supply, has attracted considerable interest worldwide to recover this metal from a variety of waste streams. From among different recycling processes, hydriding-dehydriding can prove to be highly effective in recycling discarded neo magnets present in consumer electronics. In the present study, manually removed magnets from discarded Hard Disk Drives (HDDs) were subjected to the hydriding-dehydriding process in order to evaluate the resultant products for the re-fabrication of the magnets. The paper describes the effect of experimental parameters on both the hydriding and dehydriding processes as applied to different magnet chemistries.

Jan 1, 2014

By R. Dawes, B. R. Davis, T. LeBel, C. Pelow

Settling of copper, lead, and other metals in slags is an important part of overall recovery of metals, both in primary and secondary operations. The impact of slag reduction on settling is not well known. This is important since the cycle time for slag cleaning can be significantly changed with reduction of slag, through a decrease in slag viscosity and growth of metal/sulphide particles. KPM has worked with a number of primary and secondary recyclers to better understand how reduction of slag can improve overall operation. In this presentation, we describe the type of test work and analysis done and how this information can be used to guide improvements in metal recovery from slags. INTRODUCTION Typically, copper smelter slags contain about 1-2% copper, both in the form of copper and copper sulphide beads and dissolved copper oxide in the slag (converter slags are recycled to the smelter). With the average grade of world copper deposits close to 0.7%, it is practical to recovery copper from these slags. This is done routinely by one of two methods. The first method uses slow cooling in large ladles or beds to grow particles of copper sulphide. The slag is then crushed, milled, and floated for copper recovery. The slow cooling promotes precipitation and growing of the sulphide particles from the solution and then, the slag can then be milled to recover the copper through froth flotation. A consideration of this process includes the energy cost related to grinding, the use of water, capital cost for ladles, and the availability of tailing dumps. At the same time, the retreatment of the Cu concentrate produced in the mill will displace fresh concentrate, which ultimately results in a reduction of the throughput. The second method is the so-called “slag cleaning” and is based on the settling of copper and copper sulphides particles dispersed in the slag. This is achieved by decreasing its viscosity by increasing the slag temperature and reducing the iron spinel solid phases (magnetite) that increase the apparent viscosity of the slag. Typically, the reduction does not extend to the reduction of copper, and soluble copper (mainly as oxide) and fine matte particles remain at concentrations typically at or above 0.5% (Cardona et al., 2011; Cardona, 2011). This is an improvement on 20 years ago when slag was sent to dumps at 1% or less (Demetrio et al., 2000).

Jan 1, 2019

By Matthew Violot

Vale Canada?s Birchtree Mine, located in Thompson Manitoba, has been experiencing problems with hanging wall / footwall dilution, as well as sloughing off of adjacent stopes and temporary stope block backs. Birchtree Mine is interested in determining how time affects the stability of their open stope blocks. Many factors simultaneously influence open stope stability (rock mass quality, joint condition, stress condition). This makes it challenging to determine the influence of a single parameter such as exposure time or stand-up time. This study focuses on determining the effect of exposure time on open stope dilution and combines stress analysis and empirical based approaches.

Jun 1, 2012