Search Documents

By G. Vibert Douglas

It often happens that the field geologist encounters a fault in ground where there is little to guide him with regard to the throw, or vertical displacement, and the heave, or horizontal displacement. The following construction gives both of these components of the fault, and the writers hope that it may prove a help to others. The construction is applicable to both normal and reversed faults. Briefly the procedure is as follows: Take a point which is common to the faulted geological feature and to the fault plane and on the downthrow side of the fault. Move this point in the horizontal plane in the direction indicated by the fault striæ. Rebat the point down to the plane of the fault and obtain its throw. Next consider the other side of the fault and truncate it down by the amount of the throw just determined. Then project the line of the geological feature through to the trace of the fault-plane at the lower horizon. The result is the relative positions of the two parts of the original geological feature as severed by the fault. In Figure r, let us consider a typical normal fault, that is, a fault in which the hanging-wall has gone down relative to the footwall. This characteristic, or its alternative, the reversed fault, is determined by observation on the ground. Let AB be the line of any geological feature such as the edge of a dyke, vein, or bedded sediment. The plane of which AB is the trace may have any dip; in the present case let us say 70° right. Let FF be the trace of a fault-plane which may have any dip; let us say 35° left in this case.

Jan 1, 1928

By C. G. McLachlan

Professor H.E.T. Haultain: To me from time to time the urge comes to say the agreeable thing as well as the disagreeable in commenting on the work of others. It is a prerogative of age. I don't apologize. To myself I justify my action as based on a long experience of the matters with which I deal, and I like to tell myself that I have a certain responsibility in such matters on account of my detached position. This Noranda article is a very fine contribution concerning Canadian milling, and I am surprised that no word of commendation or thanks has appeared concerning it in the BULLETIN. There is altogether too much written in these days by men rushing into print, concerning laboratory work, that has not been tied into, nor has resulted in application in the field. The authors of this paper have not rushed into print. The preparation of this paper was evidently an uncongenial task. If the authors had been that way inclined, it could have spread over several lengthy papers. It is an important article because it represents an enormous amount of work in the laboratory and the mill, extending over a period of sixteen years, and resulting in fine metallurgical and economic results with a very difficult and involved problem. It is a fine article because it is so well prepared and presented. It deals with an unusual ore condition, but there is much in it of use to every cyanide millman. It leaves very little room for criticism, though there may be differences of opinion in regard to some of the chemistry phases with which I am not conversant. I am struck by the enormous amount of persistent, painstaking, conscientious research work involved, and in the careful, sincere way in which the methods and difficulties have been described. Persistence and sincerity are the key note of the effort. It should have a good educational effect on the rising generation of millmen, and it should continue for long as a work of reference, and a spur to others. There has been an important by-product, the training and development of the young men engaged in the work. Three of them became superintendents of important mills. One was sought for important work in Africa, another has joined a large research organization in the United States.

Jan 1, 1946

By D. Sharma, A. K. Singh, R. Singh, P. K. Mandal, M. Sarkar

"This paper deals with the stability investigations carried out at the XIVth seam of Jitpur colliery. The study was conducted to investigate the possible causes of roof cavity formation and face spalling at the middle slice face of block-3 longwall panel and to suggest remedial measures. The instrumentation and monitoring work was carried out in the panel over a period of nine months. On the basis of observations, it was found that if the maximum face span was reduced from the existing 4.8 m to 3.6 m, and if the face time schedule cycle was reduced from a maximum of 37 days to about 18 days, this problem could be eliminated. The recommendations of CMRI have been implemented in the middle slice face of block-4 panel with success. IntroductionModerate to steeply dipping, undisturbed seams of uniform thickness are worked by way of inclined slicing parallel to walls. In this method, the seams are treated as a combination of several moderately thick seams dipping parallel to roof and floor. Numerous variations of multislice mining have been used worldwide to get high coal recovery under local conditions of geology, subsidence control, proness to spontaneous combustion, statutes and economics. Multislice mining can proceed either downward descending from the roof or upward ascending from the floor. Ascending methods require backfill behind the working face to provide a base for the next slice. It is also adopted for surface protection against subsidence or mining under a massive roof. This paper presents a scientific study conducted in Jitpur colliery, IISCO where a 9 m thick seam is mined in three slices in ascending order with stowing."

Jan 1, 2002

By Minghui Li

China is the largest coal producer in the world. In 2012, the coal production in China is 3.65billion tonnes, accounting for approximately 49% of global coal production. The raw coal production in 2012 was 3.8% more than the year 2011. 56% of total raw coal has been washed. The increase in raw coal production also promotes technology to be developed and brings separation capacity become larger and larger in coal processing in China. At present, over 40 extra-large scale coal preparation plants (each plant has capacity of more than 10 Mtpa) are in operation in China, the largest one is 32.5 Mtpa. Heavy medium separation are widely used in new built coal preparation, the washing limit for thermal coal feed lower and lower, the equipment selection tends larger which brings the whole washing system simplified, the local equipment developed and manufactured are more and more used. By discussing designs of several typical thermal coal preparation plants and coking coal preparation plants in China, this thesis introduces the current design of China?s extra-large coal preparation plants, and sums up the prevailing design features and trends of extra-large coal preparation plants.

Aug 1, 2013

By The Staff

"SummaryDetermination of uranium in ores may be made by measurement of their radioactivity.The method most commonly used is that of measuring beta radiations with the tray-type beta counter. This will give an accurate uranium determination provided the sample does not contain thurium and that the beta and gamma activities have not been disturbed from their natural state of equilibrium. Such a loss of equilibrium will result from mining the ore or from the weathering of the surface rock.A method is described which eliminates errors due to loss of equilibrium. The beta and gamma activities are measured simultaneously in one simple operation. This method is recommended for assaying samples of products from milling operations and its use is limited only by the presence of thorium in a ratio greater than one part of thorium to twenty parts of uranium.A third method is recommended for the analysis of exploration samples and diamond drill cores, which may be assayed in the uncrushed state.Rapid determinations of a large number of samples is possible with the pressure ionization chamber, which is sensitive to gamma activity."

Jan 1, 1950

By Atsuki Sado, Akira Ueno, Kazuaki Takebayashi, Kunio Watanabe

The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® process in 2006 to improve product quality and productivity. After resolving various technical difficulties associated with the process, a current density of 325 A/m2 and electrolytic copper production of 234 000 tons per year were realized in 2018. In recent years, Saganoseki Smelter & Refinery has promoted treatment of recycled materials in addition to copper concentrates. Accordingly, the amount and type of impurities charged to the smelting process have tended to increase. In the electrorefining process, impurities such as nickel and antimony cause anodic passivation and formation of suspended solids, respectively. Although these undesirable phenomena can be avoided by controlling impurity concentrations in the anode and electrolyte to appropriate ranges, this also limits the choice of recycled materials that can be processed by the smelter. To achieve both stable operation of the electrorefining process and flexibility in treatment of recycled materials in the smelting process, Saganoseki Refinery improved the capacity of the impurity recovery processes during 2016 to 2018. This paper describes the expansion of the purification plant to remove and recover nickel and antimony. INTRODUCTION The Saganoseki Refinery of Pan Pacific Copper Co., Ltd., Japan, introduced the ISA 2000® (wax- less permanent cathode method) in 2006 to improve product quality and productivity. Since then, the refinery has gradually increased current density, and has been committed to establishing stable operation and high productivity via various improvements related to the electrolyte filtration and additive management systems. Figure 1 shows the trends of current density and current efficiency at the refinery. Although the current efficiency temporarily dropped when the current density was raised to 322 A/m2, it consistently exceeded 97% thereafter. At present, stable operation at 325 A/m2 has been achieved and continues.

Jan 1, 2019

By Shuai-Jun Li, Xia-Ting Feng, Xian-Jie Hao

"The anisotropy of rock is of great importance to the rock engineering. To investigate the anisotropic character of slate, the rock samples of slate under different confining pressures and bedding plane angles was conducted on the MTS. The results indicated that the relationship between bedding plane angle and elasticity modulus, friction angle, cohesion and strength was shown as U pattern. The minimum value of them is located from 30°to 45°.In addition, the elasticity modulus and Poisson's ratio increase with the increasing confining pressure. The slate behaves brittle failure both in the uniaxial and triaxial compression. The failure pattern of uniaxial compression is generally tension failure, and triaxial test usually shows shear failure. The failure angle decrease with the increasing of confining pressure.INTRODUCTIONThe anisotropy of rock is that loading in different orientations the rock has different mechanical properties. The anisotropic property of rock is always an important problem in rock engineering (Hoek E. & Brown E. T., 1980). J. C. Jaeger (1960) first presented that transverse strength criterion for sliding fracture on joint surface. Later he revised rock parameters to anisotropy empirically for isotropic Mohr- Coulomb criterion. His main idea is revising cohesion according to loading direction (J. C. Jaeger, 1971). Then, many scholars study a lot on transverse strength criterion. E. Z. Lajtai (1969) considered the influence of connecting rate in all directions in joint groups for shear strength in intact rock; R. Mclamore and K. E. Gray (1967) referenced the theory of J. C. Jaeger. They not only revised cohesion also revised friction coefficient. Y. M. Tien (2000, 2001) made further study on the influence of connecting rate in joint group to transverse strength. R. Nova (1980) studied on the variation of strength when rock specimens in triaxial pressure and complex stress paths. O. Cazacu(1998) put forwards a new anisotropic strength criterion for analyzing rock strength. S. Pietruszczak(2000) introduced fabric tensor for characterizing inner seismic structure and he built an anisotropic strength criterion containing the invariants of stress tensor and seismic fabric tensor."

Jan 1, 2015

By E. Trickey

In the mining industry there exists a constant drive for increased safety and productivity and decreased operating costs. This acts as a driver for implementing advanced technology. As more and more mining operations turn to new technologies, an observed bottle-neck for technology advancement has been the limitation of machine vision solutions available. LiDAR has been seen as a possible solution to the machine vision problem. In the past, a few studies on machine vision solutions have been undertaken by various groups involving scanning laser range-finders and millimetre-wave radar. These studies have done little more than highlight the limitations of both technologies in the mining environment. Little work has been done, however, exploring the applicability of LiDAR imaging technology for mining applications. Neptec Technologies Corp. has developed an obscurant-penetrating LiDAR (OPAL) sensor technology which overcomes the limitations faced by traditional LiDAR sensors when operating in a dusty environment, as well as advanced 3D real-time intelligence (3DRi) data processing algorithms that enable the real-time exploitation of 3D imaging data with sensors mounted on moving vehicles. Working with Teck Resources Ltd. and Barrick Gold Corporation, Neptec is adapting the OPAL sensors and 3DRi technology to mining applications. This paper highlights a number of real-time OPAL/3DRi based mining applications demonstrating how this technology overcomes the limitations of traditional LiDAR to provide a real-time machine vision solution that supports mine machine autonomy.

Aug 1, 2013

"One of the corporate values mentioned by many companies deals with respect for people. This paper discusses one aspect of this value, namely, the need for clarity of accountabilities and authorities. The job of the manager in achieving this goal is analyzed and the benefits of enhancing the manager-employee conversation outlined. IntroductionCorporate values usually refer to the standards of behaviour that the leaders of the organization expect of all employees, including themselves, in carrying out their duties. Terms such as integrity, respect for the individual, continuous improvement, continuous learning, teamwork, speed, and innovation are quite common. The company-specific values are typically developed by the top executives of the company, and then tested with a broader group of employees. Where the process works, employees have a good understanding of what behaviour is expected of them in doing their work, in making difficult decisions, and in interacting with others.Having spent considerable time in his career investigating and studying the management systems at over 50 of the most successful companies in Canada, the United States, Europe and Japan, the author has had the opportunity to visit organizations such as Hewlett-Packard, 3M, Xerox, Intel, Toyota, NEC, Komatsu, British Airways, and Eastman Chemical. These experiences, together with the work of many other researchers, including the work of Dr. Elliott Jacques, have helped significantly to form the thoughts expressed below.Rather than reviewing the creation of corporate values and their deployment through the organization, these remarks focus on issues over which managers and employees have some control. The value in which managers can have significant impact deals with people and the respect shown them in the workplace. The component of respect to be emphasized is to be clear about expectations or accountabilities for oneself and the people who report to you, and to ensure that personal authority matches those expectations."

Jan 1, 1999

By Tyler Roberts

New Afton mine is an 11,000 tonne per day block caving operation, located 8 km west of the city of Kamloops, British Columbia. Due to the nature of block caving and the weak rock mass at New Afton, the mine has faced and overcome many blasting challenges during its ramp-up to commercial production. As New Afton Mine continues to grow the demand for drill and blast precision has continued to grow as well; any misstep incurs delays in achieving full production capacity. The block cave mining method used at New Afton employs single-shot draw-bells, fired with very little void and blind undercutting, allowing little margin for error. New Afton has made continuous improvements to its blasting strategy by reacting quickly to real-time problems and employing sustainable, repeatable solutions to overcome its unique blasting requirements. Examples of these solutions include: increasing blast hole diameter, casing production drill holes, developing pre-loading procedures and developing strategies for remotely blasting under-broken remnants in both draw-bells and undercutting. Increasing the blast hole diameter has alleviated initial problems with hole plugging in the highly jointed rock mass at New Afton. This has reduced drill-cleaning time significantly and enabled New Afton to meet blasting targets. PVC hole casing was trialed when blasting in extremely fractured ground, where drill holes continually plugged. The casing allowed the drill holes to remain open long enough to load and blast. Calculations were carried out in order to achieve the same explosive energy in the cased holes as a typical blast. Results were generally positive, but more testing is required. Production flexibility and scheduling reliability have been maintained at New Afton by developing a pre-loading procedure for the production undercutting. In doing so, New Afton has been able to keep productivity high by having a flexible production schedule that is not reliant on a specific piece of equipment or production drive to remain productive; this flexibility is because the mucking of undercut material can occur at any stage of the drill/blast/muck cycle. New Afton has developed a strategy for blasting remnant under-break in its draw-bells and undercutting by remotely drilling holes near to the under-broken section and then loading the toes of these holes with emulsion, the remainder of the hole is then filled with grout. The holes are grouted in order to prevent damage to permanent pillars between draw-bells (where the majority of the recovery holes need to be located). Several critical areas were recovered using this technique with little to no damage to the remaining permanent pillars. Innovative blasting solutions have allowed New Afton to overcome obstacles in order to become a producing operation. Moving forward, New Afton looks to continue its trend of innovative drilling and blasting techniques when faced with out of the ordinary situations.

Aug 1, 2013

By Q. G. Reynolds, R. T. Jones

"Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. A mathematical description is presented for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are shown to have a significant effect on the residence time distribution.INTRODUCTIONThere are some processes in which the time spent by the feed material in a smelting furnace plays a significant role in determining the extent of the reactions between metal and slag and influences the degree of settling of metal droplets from a molten slag.Residence time distributions are well defined for batch and continuously stirred reactors. However, there exist many smelting furnaces that do not fit either of these classifications. Here we will focus on producing a mathematical description for the case of a furnace that is fed continuously, but where the liquid slag and metallic products are tapped intermittently. The effects of slag and metal tapping intervals and the fraction of liquid retained in the furnace, are studied.Previous work (Jones, la Grange and Assis, 1997) has studied the effect of retention time on the degree of cobalt recovery achieved in a slag reduction process. In that work, a method was proposed for the calculation of the mean residence time of the contents of a pilot-plant furnace. That approach is to be extended here for the purposes of providing a more general design or scale-up tool.The maximum allowable depth of molten material in a given furnace is affected by such factors as the desired batch size (or the size of the ladles) and the pressure of the molten material that the tap-hole and surrounding system can withstand. Within these constraints, there might be some scope for choice of taphole position. The effects of this choice need to be understood mathematically."

Jan 1, 2012

By D. Sanguinetti, A. Consigny, M. Nodwell

"Alkali precipitation of dissolved metals is an inexpensive but non-selective means of treating mine wastewater. Alternatively, sulphide precipitation can treat to below parts-per-million concentrations while selectively recovering valuable metals. While technically feasible, sulphide treatment of dilute waste streams increases the size and cost of the plant relative to the metals loading. Ion exchange has been applied at two separate sites to pre-concentrate nickel containing wastewater prior to recovery in smaller and more cost effective sulphide precipitation circuits. The result is a dual-circuit system that can maintain high selectivity and reduce overall facility cost while meeting strict effluent regulations.INTRODUCTIONAlkali precipitation using lime is the most common method of treating mining effluents for dissolved metals removal. This method is generally sufficient for waste streams containing mixed metals of little value, and for meeting modest metal concentration limits in the final effluent. Due to the non-selective nature of the lime process, the produced metal hydroxide sludge is of little value. All metals are removed together in a sludge product which cannot be re-processed for further value recovery.By contrast, sulphide precipitation can be used to selectively remove and recover valuable base metals (such as copper, zinc, nickel and cobalt), since the sulphide will preferentially target these metals without reacting with less valuable metals (such as iron and aluminum). The low solubility of the metal sulphide solids also supports the removal of base metals to lower concentrations than can be achieved with alkali precipitation in addition to other benefits discussed more fully in a prior paper (Bratty, Lawrence, Kratochvil & Marchant, 2006). The corollary to this solubility feature is that sulphide precipitation can function on influent streams containing low (< 10 mg/L) metals concentrations to meet very low parts-perbillion final effluent concentrations. Reagent overdosing is also minimized when compared to alkali precipitation."

Jan 1, 2012

By N. Bakhshizadeh

In this investigation, the aging effect on creep behavior of A12024-10%SiC composite fabricated by powder metallurgy was studied. P/M bars were manufactured by hot powder extrusion method at 450°C with a ratio of 16 to 1. Creep specimens were over-aged at 187 ºC for 43 h. It was found that almost full density composite with relatively homogenous distribution of reinforcing particles throughout the aluminum alloy matrix could be attained by direct powder extrusion process. Creep tests were conducted at temperatures from 275 to 325°C under stresses from 25 to 60 MPa. The analysis of the creep mechanism determined that dislocation glide was the predominant mechanism of plastic deformation. The activation energy of the creep process was found to be higher than that of lattice self-diffusion in pure aluminum.

Jan 1, 2007

By J. Paquin, P. Doiron, G. Proulx, P. Champoux

After nine years on a 36 hour schedule and two programs of creeping, the Alcoa Deschambault Potroom of faced the necessity of changing its organization for many reasons: the anodes butts were too small, the anode schedule was unbalanced, the iron content in the metal trends had increased, the metal tapping volume did not convene with crucible capacity and the liquid measurement task was delayed by tapping activities. A kaizen activity inspired the Potroom department to improve the organization. A team of 15 people including the process engineer, the process technician, team supervisors and Potroom operators developed a scenario, which would permit flexibility to creep pots if energy is available and an increase of added value production.This paper will describe the systematic approach, the communication method, the trials, the changes, and our success, along with the problems experienced by the team during the adaptation of Alcoa Deschambault Potroom organization over a 20 month period. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By JOHN DUNFIELD

Good quality sphagnum peat bogs occur across Canada in areas of ample rainfall and cool, temperate climates. Early peat production techniques were restricted primarily to hand digging blocks of peat and piling them up to be dried by sun and wind. Suburban de velopment in the 1950s and the concomitant spread of home gardening triggered a dramatic growth in peat demand; labour costs rose in the same period. Peat production techniques had to alter accordingly. The three mechanical inno vations attempted were hydraulic mining, mechanical block digging and vacuum harvesting. Of these, the last method pro ved the most successful in Canada and is used to harvest 80% of Canadian peat production. Escalating transportation costs are the most important feature affecting future development of the Canadian peat industry.

Jan 1, 1984

By Ming’an Wei, Qifu Duan, Jianmin Wu, Lusheng Zhou, HMR Group Limited / HMR Technology Canada Ltd., Wenjian Wu

"The development and industrial applications of magnetic liners have been around for decades. A Swedish company Skega first introduced rubber magnetic liners, and then followed by the Chinese invention of metal magnetic liners. Traditionally, both liners were used in secondary ball mills and regrind ball mills for industrial applications, especially for ores containing magnetic materials. Mostly steel balls or equivalent forged steel balls, usually below 60 mm in diameter, were used as grinding media. With the development of mineral resources over the years, SAG mills and larger ball mills have become the dominating components for comminution circuit design. Due to the development of larger diameter ball mills and thus larger ball charge diameter (up to 80mm) especially in non-ferrous metal mining operations, the application of magnetic liners have been very limited. Based on “Magnetism theory” and the development of new materials, the HMR Group Limited has been conducting researches on examining the structures of magnetic liners, associated materials and magnetic circuits which led to the invention of the Nano Alloy Steel Magnetic Liner (NSML). Recently, NSML had a successful application in a 5.5 m diameter × 6.5 m ball mill at the Erdenet Copper Mine in Mongolia. The NSML successfully handled a ball size up of to 80 mm, while achieving a service life of nearly 24 months, which is almost 3 times wear life of the original manganese steel liners.INTRODUCTIONDuring the development and utilization of mineral resources, mineral processing is an indispensably operation. The effective separation of various useful minerals depends on sufficient monomer dissociation of minerals in the ores. The crushing and grinding operation is prior operation of mineral processing. Ball mills are used in different concentrators. As the main consumption parts of mill, liners have been studied constantly. As a new kind of liners, magnetic liners besides can meet the requirement of production, and also have characteristics with maintenance-free, saving energy and increasing efficiency. So the magnetic liners are worth to be spread and applied world widely."

Jan 1, 2016

By D. D. Downing

This paper is a review of material selection considerations concerning protective coatings in the mining industry. The discussion will cover both capital-dollar projects and maintenance requirements. Emphasis will be on industrial finishes for structural steel and process equipment subjected to aggressive atmospheres. The presentation will cover the total needs of a job, emphasizing not only the owner&apos;s requirement for a cost-effective system during plant operations, but also taking into consideration the short-term requirements of general contractors, steel fabricators, erection firms and paint contractors.

Jan 1, 1979

By G. H. Montgomery

THE PROPERTY of Aunor Gold Mines, Limited, consists of eleven claims, located in Deloro township, approximately three miles southeast of the town of Timmins. Production began in 1940 and currently the mine is operating at a rate of 485 tons per day. GEOLOGY AND MINE DEVELOPMENT The ore zone at Aunor occurs in altered lavas bounded on either side by soft talc-chlorite schist, locally known as &apos;soapstone&apos;. The zone has a strike of N.80°E, dips 60° North, and varies in width from 0 to 250 feet. Within this zone the main orebody has a westerly plunge, away from the No. 1 shaft area (Figure 1). The mine is developed by a vertical three-compartment shaft from surface to the 3,082-foot horizon. Working levels are spaced at 125- foot intervals from the 625-foot to the 1,625-foot horizon, from which to tl1e 2,125-foot level the interval is 250 feet.

Jan 1, 1957

By A. H. Lang

THE recent production of important quantities of high-grade muscovite at the Purdy mine, near Eau Claire, Ontario, bas brought that district into prominence and bas added another strategic mineral to the list of Canadian products. The discoveries are thirteen miles west of Mattawa and about two miles north of the Trans-Canada highway and the Canadian Pacific railway. HISTORY Clear mica of low power factor is in considerable demand in Canada and in the United States for war purposes such as radio and telephone condensers, aircraft spark-plugs, radio tubes, and transformers. Some muscovite (white mica) bas been produced in North Carolina and New Hampshire, but the United States trade bas depended largely on importations of muscovite from India and of phlogopite (amber mica) from Madagascar. For many years Canada bas been a substantial producer of phlogopite, but was unable to compete extensively in the United States with importations from abroad. Canadian production of muscovite bas been negligible as no important deposits were known. Ever since the construction of the Canadian Pacific railway, attempts have been made from time to time to mine the pegmatite dykes in and near the Eau Claire area, but, although some feldspar has been mined, no appreciable muscovite was produced. Lace in 1941, J. Purdy and H. MacDonald discovered a dyke containing large crystals of high-grade muscovite from which they are reported to have sold $700 worth of mica. They recorded claims 35974 and 35975 in December, 1941, and claim 36095 in May, 1942.

Jan 1, 1943

By John F. Gartner

"Traditionally, the geologists of Canada have been occupied with the tasks of finding new mineral bodies, locating gas and oil fields or hunting for economic deposits of industrial minerals. A very minor percentage of graduate geologists have applied their skills to solution of the ""urban blight"" or employing their understanding of ""Nature"" for the optimum use of land by mankind. However, things are changing quickly. The role of the geologist in the planning process is being established. It is an exciting time! Geologists are now being consulted on a wide range of urban planning problems. These vary, tor example, from assessment of the geological environment for the new communities of Erin Mills and Meadowvale, which will have total populations in excess of 100,000 people (truly a satellite city), to a complete geological/ geohydrological assessment of the new sanitary landfill for the city of Guelph.Use of geologic techniques and methods for urban studies must be enhanced with certain skills not taught, in the past, to the geologist. These include airphoto interpretation, soil mechanics, geohydrology, municipal engineering and highway engineering to mention a few. The geologist has the unique training to assess the natural environment and to discover, warn and explain the implications of man's attempt to command his environment."

Jan 1, 1972